Influência do ruído sonoro subaquático na variação dos assobios do boto-cinza, Sotalia guianensis

A poluição sonora é um grave problema nos oceanos devido à eficiência de propagação do som na água e à importância da comunicação acústica para os organismos marinhos. Delfinídeos utilizam o som para comunicação, coordenação de grupo, percepção do hábitat e busca por alimentos, já tendo sido demonstrado que podem alterar suas vocalizações em função do aumento do ruído subaquático. O presente estudo realizou uma comparação dos assobios do boto-cinza Sotalia guianensis em dois ambientes acústicos distintos, um silencioso e um ruidoso, dentro da Baía de Guanabara, Rio de Janeiro, Brasil. Também foram realizadas investigadas as relações dos parâmetros acústicos dos assobios de S. guianensis com os valores de pressão sonora do ruído subaquático. O sistema de gravação foi totalmente calibrado e consistiu de um gravador digital Marantz PMD670 com taxa de amostragem de 96 kHz e um hidrofone HTI-96MIN (5 Hz 30 kHz, sensibilidade média de -170,5 dB re 1 Pa). As gravações realizadas dos assobios e do ruído subaquático ocorreram simultaneamente em duas regiões da baía: a APA de Guapimirim e o Canal central. Durante o período de amostragem os grupos de S. guianensis foram observados em três estados comportamentais: alimentação, deslocamento e socialização; foram anotadas também informações quanto a tamanho e composição de grupo. A análise dos assobios foi realizada no software Raven 1.4 e 10 parâmetros acústicos foram extraídos. Também foi calculada a razão de emissão de assobios. A análise de ruído subaquático foi realizada no software Adobe Audition 1.5, onde foram extraídos valores de pressão sonora do ruído 300ms imediatamente antes de cada assobio analisado, sendo utilizados para análise estatística os maiores valores de pressão sonora dentro de sete intervalos de frequência. Um Teste U de Mann-Whitney foi aplicado para comparar os parâmetros acústicos dos assobios e os valores de pressão sonora das duas regiões amostradas. Esta comparação foi feita para cada estado comportamental observado durante a coleta. Posteriormente foi realizado um teste de correlações de Spearman para investigar a relação entre os parâmetros acústicos e os valores de pressão sonora. Este teste também foi feito separadamente para cada estado comportamental. No comportamento de alimentação foi encontrada diferença na duração, na frequência central e em todos os valores de pressão sonora. Durante o comportamento de socialização foi encontrada diferença na duração e em todos os valores de pressão sonora. Durante o comportamento de alimentação foi encontrada relação entre cinco parâmetros acústicos, a taxa de vocalização e a pressão sonora. Durante o comportamento de socialização foi encontrada relação entre a duração e a pressão sonora. S. guianensis alterou seu comportamento acústico em situações ruidosas, diminuindo a duração e aumentando a taxa de vocalização. Na Baía de Guanabara esta espécie está exposta diariamente a poluição sonora, sendo a APA de Guapimirim o ambiente acústico menos perturbado a que S. guianensis tem acesso.

Estudo da precisão e da exatidão da técnica da birrefringência acústica na avaliação de tensões residuais e aplicadas.

Este trabalho apresenta um procedimento numérico para o estudo da precisão e da exatidão da técnica de birrefringência acústica como usada no Instituto de Engenharia Nuclear (IEN) para avaliação de tensões residuais e aplicadas em estruturas metálicas. Esse procedimento deverá ser incorporado posteriormente ao módulo de processamento de sinal do sistema ultrassônico utilizado no Laboratório de Ultrassom do IEN para levar em conta, de forma automática e sistemática, as incertezas nos dados de entrada e as suas propagações ao longo dos cálculos efetuados. A birrefringência acústica é geralmente definida a partir das velocidades de duas ondas ultrassônicas volumétricas de incidência normal e ortogonais entre si. A birrefringência pode ser definida diretamente a partir dos tempos de percurso dessas duas ondas, uma vez que elas percorrem o mesmo espaço físico. Os tempos de percurso das ondas podem ser assim considerados como as variáveis primárias de interesse. Por meio da teoria da acustoelasticidade é possível relacionar a birrefringência acústica com as tensões atuantes no material explorando o fato da velocidade da onda ultrassônica ser afetada pela presença de um campo de tensões. Nesta dissertação elaborou-se um conjunto de planilhas eletrônicas no aplicativo Microsoft Excel para efetuar de forma automática todos os cálculos necessários ao objetivo proposto, levando em conta as incertezas nos dados, sua propagação ao longo dos cálculos e o número de dígitos significativos nos resultados. Como exemplo do procedimento desenvolvido, o estudo da precisão e da exatidão na determinação das tensões em uma viga de aço sob flexão pela técnica da birrefringência acústica é apresentado. Como valor de referência, para fins do cálculo da exatidão alcançada, utilizou-se uma solução analítica derivada da teoria clássica da resistência de materiais. Os resultados encontrados indicaram uma razoável precisão, com um erro relativo menor do que 8%, e uma baixa exatidão, menor do que 57%, nos pontos da viga sujeitos às maiores tensões principais de flexão.

Three-dimensional ultrasound imaging.

This review is about the development of three-dimensional (3D) ultrasonic medical imaging, how it works, and where its future lies. It assumes knowledge of two-dimensional (2D) ultrasound, which is covered elsewhere in this issue. The three main ways in which 3D ultrasound may be acquired are described: the mechanically swept 3D probe, the 2D transducer array that can acquire intrinsically 3D data, and the freehand 3D ultrasound. This provides an appreciation of the constraints implicit in each of these approaches together with their strengths and weaknesses. Then some of the techniques that are used for processing the 3D data and the way this can lead to information of clinical value are discussed. A table is provided to show the range of clinical applications reported in the literature. Finally, the discussion relating to the technology and its clinical applications to explain why 3D ultrasound has been relatively slow to be adopted in routine clinics is drawn together and the issues that will govern its development in the future explored.

Magnetoacoustic properties of self-biased Terfenol-D 2-2 composites

Self-biased Terfenol-D 2-2 composites exhibit high frequency of actuation and good magnetomechanical properties; however, their potential usefulness is highly dependent on their magnetoacoustic properties, particularly for ultrasonic applications. The speed of sound, c, and its variation with an externally applied magnetic field have been measured for the above composites using a 10 MHz longitudinal pulse. When the sound propagates parallel to the layers, the acoustic impedance was found to be independent of the external applied field, and lower than that for bulk Terfenol-D. The magnetomechanical coupling coefficient was found to be generally low (up to 0.35) and dependent on the volume ratio of materials, being higher for the specimens with greater content of Terfenol-D. The low attenuation, low acoustic impedance, and high frequency of actuation make this structure an interesting alternative for use in underwatersound navigation and ranging and other ultrasonic applications. When the pulse propagates orthogonal to the layers, c was found to vary by up to 3% with the application of an external field, but the acoustic attenuation was found to be very high due to the multiple reflections produced at the interfaces between the layers. This latter phenomenon has been calculated theoretically. © 2007 American Institute of Physics.

Innovative fabrication of PZT pillar arrays by a colloidal approach

An innovative approach for fabricating pillar arrays for ultrasonic transducer applications is disclosed. It involves the preparation of concentrated piezoelectric lead zirconate titanate (PZT) suspensions in aqueous solutions of epoxy resin and its polymerization upon adding a polyamine based hardener. Zeta potential and rheological measurements revealed that 1wt.% dispersant, 20wt.% of epoxy resin and a hardener/epoxy resin ratio of 0.275mLg -1, were the optimized contents to obtain strong PZT samples with high green strength (35.21±0.39MPa). Excellent ellipsoidal and semi-circle shaped pillar arrays presenting lateral dimensions lower than 10μm and 100μm height were successfully achieved. The organics burning off was conducted at 500°C for 2h at a heating rate of 1°Cmin -1. Sintering was then carried out in the same heating cycle at 1200°C for 1h. The microstructures of the green and sintered ceramics were homogeneous and no large defects could be detected. © 2011 Elsevier Ltd.

Occurrence of particle debris field during focused Ga ion beam milling of glassy carbon

To explore the machining characteristics of glassy carbon by focused ion beam (FIB), particles induced by FIB milling on glassy carbon have been studied in the current work. Nano-sized particles in the range of tens of nanometers up to 400 nm can often be found around the area subject to FIB milling. Two ion beam scanning modes - slow single scan and fast repetitive scan - have been tested. Fewer particles are found in single patterns milled in fast repetitive scan mode. For a group of test patterns milled in a sequence, it was found that a greater number of particles were deposited around sites machined early in the sequence. In situ EDX analysis of the particles showed that they were composed of C and Ga. The formation of particles is related to the debris generated at the surrounding areas, the low melting point of gallium used as FIB ion source and the high contact angle of gallium on glassy carbon induces de-wetting of Ga and the subsequent formation of Ga particles. Ultrasonic cleaning can remove over 98% of visible particles. The surface roughness (Ra) of FIB milled areas after cleaning is less than 2 nm. © 2010.

An analytical model for guided wave inspection optimization for prismatic structures of any cross section.

This paper presents an analytical modeling technique for the simulation of long-range ultrasonic guided waves in structures. The model may be used to predict the displacement field in a prismatic structure arising from any excitation arrangement and may therefore be used as a tool to design new inspection systems. It is computationally efficient and relatively simple to implement, yet gives accuracy similar to finite element analysis and semi-analytical finite element analysis methods. The model has many potential applications; one example is the optimization of part-circumferential arrays where access to the full circumference of the pipe is restricted. The model has been successfully validated by comparison with finite element solutions. Experimental validation has also been carried out using an array of piezoelectric transducer elements to measure the displacement field arising from a single transducer element in an 88.9-mm-diameter pipe. Good agreement has been obtained between the two models and the experimental data.

Microfluidics-based acoustic microbubble biosensor

This paper proposes a chip-scale microbubble-based biosensing platform. An encapsulated microbubble oscillates acoustically in liquid when exposed to an ultrasound field with its resonant frequency set by shell parameters. Changes in the resonant frequency of the microbubble can be used to monitor analyte-binding events on the shell. A device concept is proposed where ultrasonic transducers are integrated within a microfluidic channel, inside which electrodes are patterned for differential measurements of microbubble impedance. This device enables simultaneous measurements of the acoustic and electrical response of the microbubble, from which both mechanical and electrical parameters can be extracted. These parameters are used to provide a signature of the analyte. This paper presents acoustic and electrical models of the microbubbles, with the effect of shell parameters being thoroughly discussed. © 2013 IEEE.

A passive acoustic monitoring method applied to observation and group size estimation of finless porpoises

The present study aimed at determining the detection capabilities of an acoustic observation system to recognize porpoises under local riverine conditions and compare the results with sighting observations. Arrays of three to five acoustic data loggers were stationed across the main channel of the Tian-e-zhou Oxbow of China's Yangtze River at intervals of 100-150 m to record sonar. signals of free-ranging finless porpoises (Neophocaena phocaenoides). Acoustic observations, concurrent with visual observations, were conducted at two occasions on 20-22 October 2003 and 17-19 October 2004. During a total of 42 h of observation, 316 finless porpoises were sighted and 7041 sonar signals were recorded by loggers. The acoustic data loggers recorded ultrasonic signals of porpoises clearly, and detected the presence of porpoises with a correct detection level of 77.6% and a false alarm level of 5.8% within an effective distance of 150 m. Results indicated that the stationed passive acoustic observation method was effective in detecting the presence of porpoises and showed potential in estimating the group size. A positive linear correlation between the number of recorded signals and the group size of sighted porpoises was indicated, although it is faced with some uncertainty and requires further investigation. (C) 2005 Acoustical Society of America.

Echolocation signals of the free-ranging Yangtze finless porpoise (Neophocaena phocaenoides asiaeorientialis)

This paper describes the high-frequency echolocation signals from free-ranging Yangtze finless porpoise in the Tian-e-zhou Baiji National Natural Reserve in Hubei Province, China. Signal analysis showed that the Yangtze finless porpoise clicks are typical high-frequency narrow-band (relative width of the frequency spectrum Q=6.6 &PLUSMN; 1.56, N=548) ultrasonic pulses. The peak frequencies of the typical clicks range from 87 to 145 kHz with an average of 125 &PLUSMN; 6.92 kHz. The durations range from 30 to 122 μ s with an average of 68 &PLUSMN; 14.12 μ s. The characteristics of the signals are similar to those of other members of the Phocoenidae as well as the distantly related delphinids, Cephalorhynchus spp. Comparison of these signals to those of the baiji (Lipotes vexillifer), who occupies habitat similar to that of the Yangtze finless porpoise, showed that the peak frequencies of clicks produced by the Yangtze finless porpoise are remarkably higher than those produced by the baiji. Difference in peak frequency between the two species is probably linked to the different size of prefer-red prey fish. Clear double-pulse and multi-pulse reverberation structures of clicks are noticed, and there is no indication of any low-frequency (< 70 kHz) components during the recording period. © 2005 Acoustical Society of America.

Comparison between visual and passive acoustic detection of finless porpoises in the Yangtze river, China

Recently, sonar signals and other sounds produced by cetaceans have been used for acoustic detection of individuals and groups in the wild. However, the detection probability ascertained by concomitant visual survey has not been demonstrated extensively. The finless porpoises (Neophocaena phocaenoides) have narrow band and high-frequency sonar signals, which are distinctive from background noises. Underwater sound monitoring with hydrophones (B&K8103) placed along the sides of a research vessel, concurrent with visual observations was conducted in the Yangtze River from Wuhan to Poyang Lake in 1998 in China. The peak to peak detection threshold was set at 133 dB re 1 mu Pa. With this threshold level, porpoises could be detected reliably within 300 m of the hydrophone. In a total of 774-km cruise, 588 finless porpoises were sighted by visual observation and 44 864 ultrasonic pulses were recorded by the acoustical observation system. The acoustic monitoring system could detect the presence of the finless porpoises 82% of the time. A false alarm in the system occurred with a frequency of 0.9%. The high-frequency acoustical observation is suggested as an effective method for field surveys of small cetaceans, which produce high-frequency sonar signals. (C) 2001 Acoustical Society of America.

超声波对HCFC-141b水合物形成过程的影响研究

针对水合物形成过程中存在成核诱导期长、过冷度大，形成速度慢的问题，本文以HCFC-141b（1，1-dichloro-1-flooroethane）作为研究工质，将超声波引入水合物形成过程中，研究超声波对水合物形成的影响。建立了包括超声波水合反应系统、数据采集和图像采集系统的可视化低温实验系统。利用这套实验系统，分别实验研究了频率为20kHz和15kHz，功率为0-1000w的超声波对HCFC-141b水合物的形成影响。实验结果表明，超声波对水合物的形成有明显的影响。水合物形成过程主要分为三阶段：冷却期、