Titanium dioxide based nanomaterials for photocatalytic water treatment

Water treatment using photocatalysis has gained extensive attention in recent years. Photocatalysis is promising technology from green chemistry point of view. The most widely studied and used photocatalyst for decomposition of pollutants in water under ultraviolet irradiation is TiO2 because it is not toxic, relatively cheap and highly active in various reactions. Within this thesis unmodified and modified TiO2 materials (powders and thin films) were prepared. Physico-chemical properties of photocatalytic materials were characterized with UV-visible spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectrometry (XPS), inductively coupled plasma optical emission spectroscopy (ICP-OES), ellipsometry, time-of-flight secondary ion mass spectrometry (ToF-SIMS), Raman spectroscopy, goniometry, diffuse reflectance measurements, thermogravimetric analysis (TGA) and nitrogen adsorption/desorption. Photocatalytic activity of prepared samples in aqueous environment was tested using model compounds such as phenol, formic acid and metazachlor. Also purification of real pulp and paper wastewater effluent was studied. Concentration of chosen pollutants was measured with high pressure liquid chromatography (HPLC). Mineralization and oxidation of organic contaminants were monitored with total organic carbon (TOC) and chemical oxygen demand (COD) analysis. Titanium dioxide powders prepared via sol-gel method and doped with dysprosium and praseodymium were photocatalytically active for decomposition of metazachlor. The highest degradation rate of metazachlor was observed when Pr-TiO2 treated at 450ºC (8h) was used. The photocatalytic LED-based treatment of wastewater effluent from plywood mill using commercially available TiO2 was demonstrated to be promising post-treatment method (72% of COD and 60% of TOC was decreased after 60 min of irradiation). The TiO2 coatings prepared by atomic layer deposition technique on aluminium foam were photocatalytically active for degradation of formic and phenol, however suppression of activity was observed. Photocatalytic activity of TiO2/SiO2 films doped with gold bipyramid-like nanoparticles was about two times higher than reference, which was not the case when gold nanospheres were used.

Adsorção de corantes têxteis aniônicos e catiônicos em resíduos do processamento de fios de algodão modificados quimicamente

The textile industry generates a large volume of high organic effluent loading whoseintense color arises from residual dyes. Due to the environmental implications caused by this category of contaminant there is a permanent search for methods to remove these compounds from industrial waste waters. The adsorption alternative is one of the most efficient ways for such a purpose of sequestering/remediation and the use of inexpensive materials such as agricultural residues (e.g., sugarcane bagasse) and cotton dust waste (CDW) from weaving in their natural or chemically modified forms. The inclusion of quaternary amino groups (DEAE+) and methylcarboxylic (CM-) in the CDW cellulosic structure generates an ion exchange capacity in these formerly inert matrix and, consequently, consolidates its ability for electrovalent adsorption of residual textile dyes. The obtained ionic matrices were evaluated for pHpcz, the retention efficiency for various textile dyes in different experimental conditions, such as initial concentration , temperature, contact time in order to determine the kinetic and thermodynamic parameters of adsorption in batch, turning comprehensive how does occur the process, then understood from the respective isotherms. It was observed a change in the pHpcz for CM--CDW (6.07) and DEAE+-CDW (9.66) as compared to the native CDW (6.46), confirming changes in the total surface charge. The ionized matrices were effective for removing all evaluated pure or residual textile dyes under various tested experimental conditions. The kinetics of the adsorption process data had best fitted to the model a pseudosecond order and an intraparticle diffusion model suggested that the process takes place in more than one step. The time required for the system to reach equilibrium varied according to the initial concentration of dye, being faster in diluted solutions. The isotherm model of Langmuir was the best fit to the experimental data. The maximum adsorption capacity varied differently for each tested dye and it is closely related to the interaction adsorbent/adsorbate and dye chemical structure. Few dyes obtained a linear variation of the balance ka constant due to the inversion of temperature and might have influence form their thermodynamic behavior. Dyes that could be evaluated such as BR 18: 1 and AzL, showed features of an endothermic adsorption process (ΔH° positive) and the dye VmL presented exothermic process characteristics (ΔH° negative). ΔG° values suggested that adsorption occurred spontaneously, except for the BY 28 dye, and the values of ΔH° indicated that adsorption occurred by a chemisorption process. The reduction of 31 to 51% in the biodegradability of the matrix after the dye adsorption means that they must go through a cleaning process before being discarded or recycled, and the regeneration test indicates that matrices can be reused up to five times without loss of performance. The DEAE+-CDW matrix was efficient for the removal of color from a real textile effluent reaching an UV-Visible spectral area decrease of 93% when applied in a proportion of 15 g ion exchanger matrix L-1 of colored wastewater, even in the case of the parallel presence of 50 g L-1 of mordant salts in the waste water. The wide range of colored matter removal by the synthesized matrices varied from 40.27 to 98.65 mg g-1 of ionized matrix, obviously depending in each particular chemical structure of the dye upon adsorption.

A influência da incorporação de ácido α-eleosteárico, purificado e isolado do óleo de tungue, na dinâmica molecular de lipossomos

Este trabalho descreve o isolamento e purificação do ácido α-eleosteárico (α-ESA) a partir do óleo de tungue e sua caracterização por espectroscopia de infravermelho com transformada de Fourier (FTIR), cromatografia gasosa acoplada com espectrometria de massas (GC-MS) e espectroscopia de ressonância magnética nuclear (RMN) de 1H e 13C. O α-ESA apresenta atividades biológicas (antitumorais, anti-inflamatórias e antioxidantes), tornando-se importante compreender sua interação com membranas lipídicas. Assim, este trabalho também descreve resultados referentes ao efeito da incorporação de α-ESA na dinâmica molecular de lipossomos compostos por fosfatidilcolina. O sistema lipossomal puro e contendo α-ESA foi caracterizado através do uso de espectroscopia de UV-visível, FTIR, RMN e calorimetria de varredura diferencial (DSC). Como resultados da purificação do α-ESA, obtivemos uma pureza de 95,9% utilizando acetona como solvente de recristalização em detrimento dos 92,2% em solução etanólica. Na incorporação em lipossomos, observou-se uma maior interação do α-ESA com a parte polar, de interface e os primeiros metilenos da região apolar da fosfatidilcolina. Além disso, α-ESA apresentou um efeito de redução da fluidez de lipossomos. Os resultados contribuem para a geração de conhecimento para o desenvolvimento de novos sistemas farmacológicos.

Preparation, Characterization, and Photocatalytic Applications of MWCNTs/TiO2 Composite

The multiwall carbon nanotubes (MWCNTs)/titanium dioxide (P25) composite in different ratios was prepared using simple evaporation and drying process. The composite was characterized by Raman spectroscopy, X-ray diffraction (XRD), UV-visible diffuse reflectance spectroscopy, and scanning electron microscopy (SEM). The photocatalytic activity of this composite was investigated using degradation of the Bismarck brown R dye (BBR). An optimal MWCNTs/TiO2 ratio of 0.5% (w/w) was found to achieve the maximum rate of BBR degradation. It was observed that the composite exhibits enhanced photocatalytic activity compared with TiO2. The enhancement in photocatalytic activity performance of the MWCNTs/P25 composite is explained in terms of recombination of photogenerated electron-hole pairs. In addition, MWCNTs act as a dispersing support to control the morphology of TiO2 particles in the MWCNTs/TiO2 composite.

Non-inclusion complexes between riboflavin and cyclodextrins

Objectives To investigate the molecular interaction between beta-cyclodextrin (beta CD) or hydroxypropyl-beta-cyclodextrin (HP beta CD) and riboflavin (RF), and to test the anticancer potential of these formulations. Methods The physicochemical characterization of the association between RF and CDs was performed by UV-vis absorption, fluorescence, differential scanning calorimetry and NMR techniques. Molecular dynamics simulation was used to shed light on the mechanism of interaction of RF and CDs. Additionally, in-vitro cell culture tests were performed to evaluate the cytotoxicity of the RFCD complexes against prostate cancer cells. Key findings Neither beta CD nor HP beta CD led to substantial changes in the physicochemical properties of RF (with the exception of solubility). Additionally, rotating frame Overhauser effect spectroscopy experiments detected no spatial correlations between hydrogens from the internal cavity of CDs and RF, while molecular dynamics simulations revealed out-of-ring RFCD interactions. Notwithstanding, both RF beta CD and RFHP beta CD complexes were cytotoxic to PC3 prostate cancer cells. Conclusions The interaction between RF and either beta CD or HP beta CD, at low concentrations, seems to be made through hydrogen bonding between the flavonoid and the external rim of both CDs. Regardless of the mechanism of complexation, our findings indicate that RFCD complexes significantly increase RF solubility and potentiate its antitumour effect.

Síntese e caracterização de espinélios a base de Cu, Fe e Cr para pigmentos cerâmicos

Inorganic pigment comprises a host lattice, which is part of the chromophore component (usually a transition metal cation) and possible components modifiers, which stabilize, add or restate the properties pigments. Among the materials with spinel, ferrites, and the chromite stand out, because they have broad technological importance in the area of materials, applicability, pigments, catalytic hydrogenation, thin film, ceramic tiles, among others. The present work, pigments containing CuFe2O4, CuCr2O4,e CuFeCrO4, were synthesized by a method that makes use of gelatin as organic precursor using their application to ceramic pigments. The pigments were characterized by X-ray diffraction (XRD), Infrared spectroscopy, scanning electron microscopy (SEM) spectroscopy in the UV-visible and Colorimetry. The results confirmed the feasibility of the synthetic route used, with respect to powders synthesized, there is the formation of spinel phase from 500°C, with an increase in crystallinity and the formation of other phases. The pigments were shown to be crystalline and the desired phases were obtained. The copper chromite have hues ranging from green to black according to the calcination temperature, while the copper chromite doped with iron had brownish. The ferrites showed copper color and darker brown to black, which may indicate an interesting factor because of the importance of black pigment

Valorization of the Macroalgae Sargassum Muticum by Enzymatic Hydrolysis, Interest of Surfactants to Improve the Extraction of Phlorotannins and Polysaccharides

The use of surfactants to improve enzymatic hydrolysis of the macroalgae Sargassum muticum has been investigated. Visible absorption spectroscopy has been used to quantify the solubilization of both polysaccharides and phlorotannins in the hydrolysates.   After total extraction, results showed that Sargassum muticum contained 2.74% (expressed in percent of the dry weight of the algae) of phlorotannins whose 32 % were in the cell wall. This result shows that it is important to access to the parietal phlorotannins. To reach this objective, we chose the enzymatic approach for destructurating the cell wall of the algae. The use of 5% dry weight (DW - 5% by weight of hydrolyzed algae) of an enzymatic mix containing a commercial beta-glucanase, a commercial protease and an alginate lyase extracted from Pseudomonas alginovora led after 3 hours of hydrolysis to the solubilization of 2.43% DW polysaccharides and 0.52% DW phlorotannins. The use of 0.5% volume of the surfactant Triton® X-100 with 10% DW of the enzymatic mix has allowed to reaching the value of 2.63% DW of solubilized phlorotannins, that is 96% of the total phenolic content.   The use of non-ionic surfactant, combined to enzymatic hydrolysis, showed an increased efficiency in disrupting cell wall and solubilizing phlorotannins in Sargassum muticum.

Determinação eletroanalítica de ácido salicílico em produto dermatológico com eletrodos de nanotubos de carbono e nanopartículas de óxido de ferro

Dissertação (mestrado)—Universidade de Brasília, Instituto de Química, Programa de Pós-Graduação em Tecnologias Química e Biológica, 2016.

Fabricación y caracterización de películas delgadas de óxidos transparentes con aplicaciones ópticas.

Los óxidos transparentes conductores (TCO′ s) son materiales compuestos conformados por oxígeno y un metal, que presentan una combinación única de alta estabilidad química, alta concentración electrónica y alta transparencia óptica. Por esta razón, el procesamiento de TCO′ s en película delgada va orientado hacia aplicaciones específicas tales como ventanas ópticas en celdas solares, sensores de gases, electrodos en dispositivos de pantallas planas, ventanas inteligentes. En este proyecto se trabajó en la síntesis experimental de dos TCO′ s relevantes tanto en investigación fundamental como en aplicaciones tecnológicas: el óxido de indio (In2O3) y el óxido de estaño (SnO2). Ambos TCO′ s se depositaron por la técnica de erosión iónica reactiva por corriente directa (DC). Para el análisis de las películas se utilizaron varias técnicas de caracterización: difracción de rayos X, espectroscopia UV-Visible, resistividad eléctrica, efecto Hall, así como microscopías electrónica de barrido y de fuerza atómica. Se fabricó también una bicapa de In2O3/SnO2, la cual se caracterizó además con espectroscopia de fotoemisión de rayos X (XPS).En esta tesis se reporta por primera vez la síntesis y caracterización de esta bicapa, la cual abre una línea de investigación en el área de interfaces. Asimismo, se desarrolló e implementó un procedimiento, basado en los modelos ópticos, tal que permite obtener parámetros que se utilizan para evaluar a cualquier película delgada TCO como potencial metamaterial. Las propiedades de las muestras se analizaron en función de la temperatura aplicada post-depósito: temperatura ambiente (TA), 100oC, 200oC, 300oC, bajo una atmósfera de argón o argón-oxígeno. Los resultados confirman que las películas presentan un crecimiento de tipo poli cristalino. Además, la calidad cristalina tiende a incrementarse como función del incremento de la temperatura. El In2O3 creció con estructura cúbica bcc (a=10.11 ˚A, ICDD #71-2195). A partir de 200C, se detectaron trazas de la fase romboédrica (a=5.490 ˚A, c=14.520 ˚A, ICDD #73-1809). Asimismo, el SnO2 creció con estructura tetragonal (a = 4.737 ˚A, c = 3.186 ˚A, ICDD #88-0287). Las películas de In2O3 poseen una transparencia promedio del 90 % en una ventana de 500 nm a 1100 nm. El borde de absorción se recorre al azul como función de la temperatura, de Eg=3.3 eV a Eg=3.7 eV por el efecto Burstein-Moss. Por otra parte, la bicapa presentó una interfaz claramente definida, sin difusión de especies metálicas. Al incrementarse la temperatura, de TA a 400oC, se detectaron dos fases de óxido de estaño: SnO2 y SnO, en un porcentaje atómico de ≈70 %:30 %, respectivamente. Se concluye que los parámetros y valores obtenidos de las películas como son el texturizado y espesor homogéneo, alta transparencia, crecimiento preferencial, ancho prohibido y resistividad eléctrica, son comparables a los que se requieren del In2O3 y SnO2 en película delgada para aplicaciones optoelectrónicas.

Síntese de pigmento cerâmico ferrita de cobalto utilizando planejamento experimental

Synthetic inorganic pigments are the most widely used in ceramic applications because they have excellent chemical and thermal stability and also, in general, a lower toxicity to man and to the environment. In the present work, the ceramic black pigment CoFe2O4 was synthesized by the polymerization Complex method (MPC) in order to form a material with good chemical homogeneity. Aiming to optimize the process of getting the pigment through the MPC was used a fractional factorial design 2(5-2), with resolution III. The factors studied in mathematical models were: citric acid concentration, the pyrolysis time, temperature, time and rate of calcination. The response surfaces using the software statistica 7.0. The powders were characterized by thermal analysis (TG/DSC), x-ray diffraction (XRD), scanning electron microscopy (SEM) and spectroscopy in the UV-visible. Based on the results, there was the formation of phase cobalt ferrite (CoFe2O4) with spinel structure. The color of the pigments obtained showed dark shades, from black to gray. The model chosen was appropriate since proved to be adjusted and predictive. Planning also showed that all factors were significant, with a confidence level of 95%

Preparação e caracterização de catalisadores à base de titânio suportado em MCM-41 para produção de compostos oxigenados através da pirólise catalítica do capim elefante

In recent years, the area of advanced materials has been considerably, especially when it comes to materials for industrial use, such as is the case with structured porosity of catalysts suitable for catalytic processes. The use of catalysts combined with the fast pyrolysis process is an alternative to the oxygenate production of high added value, because, in addition to increasing the yield and quality of products, allows you to manipulate the selectivity to a product of interest, and therefore allows greater control over the characteristics of the final product. Based on these arguments, in this work were prepared titanium catalysts supported on MCM-41 for use in catalytic pyrolysis of biomass, called elephant grass. The reactions of pyrolysis of biomass were performed in a micro pyrolyzer, Py-5200, coupled to GC / MS, the company CDS Corporation, headquartered in the United States. The catalysts Ti-MCM-41 in different molar ratios were characterized by XRD, TG / DTG, FT-IR, SEM, XRF, UV-visible adsorption of nitrogen and the distribution of particle diameter and specific surface area measurement by the BET method. From the catalytic tests it was observed that the catalysts synthesized showed good results for the pyrolysis reaction.The main products were obtained a higher yield of aldehydes, ketones and furan. It was observed that the best reactivity is a direct function of the ratio Si/Ti, nature and concentration of the active species on mesoporous supports. Among the catalysts Ti-MCM-41 (molar ratio Si / Ti = 25 and 50), the ratio Si / Ti = 25 (400 ° C and 600 ° C) favored the cracking of oxygenates such as acids , aldehydes, ketones, furans and esters. Already the sample ratio Si / Ti = 50 had the highest yield of aromatic oxygenates

Propriedade fotoluminescente da ZrO2: Tb+3, Eu+3, Tm+3 obtida pelo método de polimerização de complexos

Recent studies are investigating a new class of inorganic materials which arise as a promising option for high performance applications in the field of photoluminescence. Highlight for rare earth (TR +3 ) doped, which have a high luminous efficiency, long decay time and being able to emit radiation in the visible range, specific to each element. In this study, we synthesized ZrO2: Tb +3 , Eu +3 , Tm +3 nanoparticles complex polymerization method (CPM). We investigated the influences caused by the heat treatment temperature and the content of dopants in zirconia photoluminescent behavior. The particles were calcined at temperature of 400, 500 and 600 ° C for two hours and ranged in concentration of dopants 1, 2, 4 and 8 mol% TR +3 . The samples were characterized by thermal analysis, X-ray diffraction, photoluminescence of measurements and uv-visible of spectroscopies. The results of X-ray diffraction confirmed the formation of the tetragonal and cubic phases in accordance with the content of dopants. The photoluminescence spectra show emission in the region corresponding simultaneous to blue (450 nm), green (550 nm) and red (615 nm). According to the results, ZrO2 particles co-doped with rare earth ions is a promising material white emission with a potential application in the field of photoluminescence

Cadmium Telluride Magic-Sized Clusters and Superstructures

The aim of the present work is to gain new insights into the formation mechanism of CdTe magic-sized clusters (MSCs) at low temperatures, as well as on their evolution towards 1D and 2D nanostructures and assemblies thereof, under mild reaction conditions. The reaction system included toluene as solvent, octylamine as primary alkylamine, trioctylphosphine-Te as chalcogenide precursor and Cd(oleate)2 as metal precursor. UV-Vis absorption spectroscopy and transmission electron microscopy (TEM) were used to analyze samples containing concentrations of octylamine of 0.2, 0.8 and 2 M: well-defined, sharp absorption peaks were observed, with peaks maxima at 449, 417 and 373 nm respectively, and 1D structures with a string-like appearance were displayed in the TEM images. Investigating peaks growth, step-wise peaks shift to lower energies and reverse, step-wise peak shift to higher energies allowed to propose a model to describe the system, based on interconnected [CdTe]x cluster units originating an amine-capped, 1-dimensional, polymer-like structure, in which different degrees of electronic coupling between the clusters are held responsible for the different absorption transitions. The many parameters involved in the synthesis procedure were then investigated, starting from the Cd:Te ratio, the role of the amine, the use of different phosphine-Te and Cd precursors. The results allowed to gain important information of the reaction mechanism, as well as on the different behavior of the species featuring the sharp absorption peaks in each case. Using Cd(acetate)2 as metal precursor, 2D structures were found to evolve from the MSCs solutions over time, and their tendency to self-assemble was then analyzed employing two amines of different alkyl chain length, octylamine (C-8) and oleylamine (C-18). Their co-presence led to the formation of free-floating triangular nanosheets, which tend to readily aggregate if only octylamine is present in solution.

Decoration of Ti/TiO2 Nanotubes with Pt Nanoparticles for Enhanced UV-Vis Light Absorption in Photoelectrocatalytic Process

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Performance characteristics of UV and visible spectrophotometry methods for quantitative determination norfloxacin in tablets

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)