Influencing effect of heat-treatment on radon emanation and exhalation characteristic of red mud

The reuse of industrial by-products is important for members of numerous industrial sectors. However, though the benefits of reuse are evident from an economical point of view, some compounds in these materials can have a negative effect on users' health.In this study, the radon emanation and exhalation features of red mud were surveyed using heat-treatment (100-1200 °C). As a result of the 1200°C-treated samples, massic radon exhalation capacity reduced from 75 ± 10 mBq kg^-1 h^-1 to 7 ± 4 mBq kg^-1 h^-1, approximately 10% of the initial exhalation rate.To find an explanation for internal structural changes, the porosity features of the heat-treated samples were also investigated. It was found that the cumulative pore volume reduced significantly in less than 100 nm, which can explain the reduced massic exhalation capacity in the high temperature treated range mentioned above.SEM snapshots were taken of the surfaces of the samples as visual evidence for superficial morphological changes. It was found that the surface of the high temperature treated samples had changed, proving the decrement of open pores on the surface.

Effect of heat treatment on reactivity-strength of alkali-activated natural pozzolans

Natural pozzolans can be activated and condensed with sodium silicate in an alkaline environment to synthesize high performance cementitious construction materials with low environmental impact. The nature of the starting materials including mineral composition, chemical composition and crystal structure groups affects the formation of the geopolymer gel phase. In this paper, the pozzolanic activities of five natural pozzolans are studied. From XRD and XRF results, most of the raw materials contain zeolite clay minerals and have a high loss on ignition. Therefore, before use, samples were calcined at 700, 800 and 900 °C, respectively. The improvement in pozzolanic properties was studied following heat treatment including calcinations and/or elevated curing temperature by using alkali solubility and compressive strength tests. The results show that pozzolan containing sodium zeolite clinoptilolite can be used to prepare a moderate to high strength binder by heat treatment and calcinations can impart disorder hornblende as a constituent of pozzolan with no amorphous phase to prepare a moderate strength binder.

EFFECT OF SORGHUM SEED TREATMENT IN BURKINA FASO VARIES WITH BASELINE CROP PERFORMANCE AND GEOGRAPHICAL LOCATION

Sorghum [ Sorghum bicolor (L.) Moench] is a major subsistence crop throughout the region of Sahel. With the exception of seeds and labour, no agricultural inputs are in general used in sorghum production since the grain is of a relatively low commercial value and the risk of losing the crop to drought, flooding, etc. is substantial. A meta-analysis of 118 field experiments was carried out to identify conditions in which two protective seed treatments could support a yield increase of sorghum in Burkina Faso. The two treatments were: i) treatment with the pesticide Calthio C (thiram and chlorpyrifos) and ii) treatment with an aqueous extract from the plant Eclipta alba . Both treatments were found to produce a yield increase (Medians: Calthio C +199 kg ha-1, P<2x10-9; E. alba +90.5 kg ha-1 P<4x10-4). A strong relative effect of Calthio C on yield (+36%) was found for field experiments with a low baseline yield. A strong relative effect of E. alba extract on yield (+22%) was found for experiments with a low baseline of emergence. ANOVA of the 118 field tests showed that baseline crop performance (yield and emergence) and the effect of seed treatments were strongly linked to geographical location (twelve different villages included). Roots from sorghum in the village showing the strongest effect of both seed treatments (>40% yield increase) were found to carry a comparatively high load of the infectious ascomycetes: Fusarium equiseti , Macrophomina phaseolina and Curvularia lunata .

Antimicrobial effect of polymeric biomaterials for bone infection treatment

Dissertação de mestrado em Bioquímica, apresentada à Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa, 2016.

Clinical efficacy of paclitaxel in the treatment of mid-stage and advanced malignant gastric cancer, and effect of nursing interventions

Purpose: To investigate the clinical efficacy of paclitaxel combined with additional chemotherapy for mid-stage and advanced malignant tumors, and the benefits afforded by scientific nursing. Methods: Patients with mid-stage and advanced gastric cancer were randomly divided into test and control groups. Control group was given intravenous chemotherapy (400 mg/m2 fluorouracil and 2500 mg/m2 cisplatin) and nursed conventionally, while the test group was additionally treated with 80 mg/m2 paclitaxel and underwent special scientific nursing. Clinical effects and changes in the rates of apoptosis and cell proliferation were recorded. The effect of applying scientific nursing on therapeutic outcomes was also evaluated. Results: The overall rate of treatment effectiveness, clinical control rate, mean apoptosis and proliferation rates in the test group were 56.40, 92.30, (7.10 ± 3.17 and 28.70 ± 3.22 %, respectively, while, in the control group, the values were 38.50, 64.10, 25.40 ± 2.67 and 32.60 ± 2.93 %, respectively. The differences were all statistically significant (p < 0.05). In terms of nursing efficacy, the test group had a lower pain score and higher quality-of-life scores (Karnofsky performance status score) than control group. There was no significant difference in the incidence of adverse reactions between the two groups (p > 0.05). Conclusion: Paclitaxel has a significant effect when used to treat mid-stage and advanced gastric cancer. Moreover, additional nursing not only enhances the therapeutic effect but also improves prognosis and quality-of-life.

Determing the Effect of Thermal Treatment Timing on Ultra-High Performance Concrete Beams

The loss of prestressing force over time influences the long-term deflection of the prestressed concrete element. Prestress losses are inherently complex due to the interaction of concrete creep, concrete shrinkage, and steel relaxation. Implementing advanced materials such as ultra-high performance concrete (UHPC) further complicates the estimation of prestress losses because of the changes in material models dependent on curing regime. Past research shows compressive creep is "locked in" when UHPC cylinders are subjected to thermal treatment before being loaded in compression. However, the current precasting manufacturing process would typically load the element (through prestressing strand release from the prestressing bed) before the element would be taken to the curing facility. Members of many ages are stored until curing could be applied to all of them at once. This research was conducted to determine the impact of variable curing times for UHPC on the prestress losses, and hence deflections. Three UHPC beams, a rectangular section, a modified bulb tee section, and a pi-girder, were assessed for losses and deflections using an incremental time step approach and material models specific to UHPC based on compressive creep and shrinkage testing. Results show that although it is important for prestressed UHPC beams to be thermally treated, to "lock in" material properties, the timing of thermal treatment leads to negligible differences in long-term deflections. Results also show that for UHPC elements that are thermally treated, changes in deflection are caused only by external loads because prestress losses are "locked-in" following thermal treatment.

Treatment trials for neonatal seizures: the effect of design on sample size

Neonatal seizures are common in the neonatal intensive care unit. Clinicians treat these seizures with several anti-epileptic drugs (AEDs) to reduce seizures in a neonate. Current AEDs exhibit sub-optimal efficacy and several randomized control trials (RCT) of novel AEDs are planned. The aim of this study was to measure the influence of trial design on the required sample size of a RCT. We used seizure time courses from 41 term neonates with hypoxic ischaemic encephalopathy to build seizure treatment trial simulations. We used five outcome measures, three AED protocols, eight treatment delays from seizure onset (Td) and four levels of trial AED efficacy to simulate different RCTs. We performed power calculations for each RCT design and analysed the resultant sample size. We also assessed the rate of false positives, or placebo effect, in typical uncontrolled studies. We found that the false positive rate ranged from 5 to 85% of patients depending on RCT design. For controlled trials, the choice of outcome measure had the largest effect on sample size with median differences of 30.7 fold (IQR: 13.7–40.0) across a range of AED protocols, Td and trial AED efficacy (p<0.001). RCTs that compared the trial AED with positive controls required sample sizes with a median fold increase of 3.2 (IQR: 1.9–11.9; p<0.001). Delays in AED administration from seizure onset also increased the required sample size 2.1 fold (IQR: 1.7–2.9; p<0.001). Subgroup analysis showed that RCTs in neonates treated with hypothermia required a median fold increase in sample size of 2.6 (IQR: 2.4–3.0) compared to trials in normothermic neonates (p<0.001). These results show that RCT design has a profound influence on the required sample size. Trials that use a control group, appropriate outcome measure, and control for differences in Td between groups in analysis will be valid and minimise sample size.

Effect of investigation intensity and treatment differences on prostate cancer survivor's physical symptoms, psychological well-being and health-related quality of life: a two country cross-sectional study.

Aim: To investigate effects on men's health and well-being of higher prostate cancer (PCa) investigation and treatment levels in similar populations. Participants: PCa survivors in Ireland where the Republic of Ireland (RoI) has a 50% higher PCa incidence than Northern Ireland (NI). Method: A cross-sectional postal questionnaire was sent to PCa survivors 2–18 years post-treatment, seeking information about current physical effects of treatment, health-related quality of life (HRQoL; EORTC QLQ-C30; EQ-5D-5L) and psychological well-being (21 question version of the Depression, Anxiety and Stress Scale, DASS-21). Outcomes in RoI and NI survivors were compared, stratifying into ‘late disease’ (stage III/IV and any Gleason grade (GG) at diagnosis) and ‘early disease’ (stage I/II and GG 2–7). Responses were weighted by age, jurisdiction and time since diagnosis. Between-country differences were investigated using multivariate logistic and linear regression. Results: 3348 men responded (RoI n=2567; NI n=781; reflecting population sizes, response rate 54%). RoI responders were younger; less often had comorbidities (45% vs 38%); were more likely to present asymptomatically (66%; 41%) or with early disease (56%; 35%); and less often currently used androgen deprivation therapy (ADT; 2%; 28%). Current prevalence of incontinence (16%) and impotence (56% early disease, 67% late disease) did not differ between RoI and NI. In early disease, only current bowel problems (RoI 12%; NI 21%) differed significantly in multivariate analysis. In late disease, NI men reported significantly higher levels of gynaecomastia (23% vs 9%) and hot flashes(41% vs 19%), but when ADT users were analysed separately, differences disappeared. For HRQoL, in multivariate analysis, only pain (early disease: RoI 11.1, NI 19.4) and financial difficulties (late disease: RoI 10.4, NI 7.9) differed significantly between countries. There were no significant between-country differences in DASS-21 or index ED-5D-5L score. Conclusions: Treatment side effects were commonly reported and increased PCa detection in RoI has left more men with these side effects. We recommended that men be offered a PSA test only after informed discussion.

Effect of acid alcoholic solution in waxy maize starch treatment.

O amido é o polissacarídeo mais abundante presente em plantas, composto por amilose e amilopectina. O amido de milho ceroso apresenta somente amilopectina. A modificação do amido é recomendada para melhorar suas aplicações. A hidrólise ácida é utilizada para alterar as propriedades físico-químicas sem modificar o grânulo e o meio alcoólico ajuda na recuperação da molécula após o tratamento. O objetivo do trabalho foi o tratamento químico com HCl 0,5 mol L-1 durante 1 hora em 100 ml de água, etanol ou metanol. Os equipamentos SETSYS Evolução TGADTA / DSC e Rápido Visco-Analisador (RVA-4) foram usados para avaliar as alterações dos amidos. As curvas TG mostraram três eventos (desidratação, estabilidade e decomposição), com resultados similares para todas as amostras. Este resultado pode estar relacionado a resistência da amilopectina para a hidrólise ácida. Na análise reológica (RVA) o tratamento das amostras mostrou valores mais baixos de perfis de viscosidade. A solução ácida forneceu mudanças nas propriedades de pasta do amido e a solução etanólica (solvente mais apolar) foi maior que as demais soluções. Conclui-se portanto que o tratamento dos amidos forneceu produtos com características térmicas similares e com diferentes respostas mecânicas

Effect of the KMnO4 Treatment on the "pinhão" starch.

O pinhão, sementes de Araucaria angustifolia, tem o amido como componente principal. Os amidos oxidados melhoram as características físico-química, de pasta e térmicas dos produtos em processos industriais. O amido de pinhão nativo foi tratado com soluções padronizadas de permanganato de potássio (KMnO4) e as amostras foram analisadas por técnicas termoanalíticas (TG-DTA) em atmosfera inerte. As amostras foram oxidadas da seguinte forma: quatro porções de 20 g (base seca) foram separadas e três foram suspensas em solução de KMnO4 (0,001; 0,002; 0,005 mol L-1) em agitação constante durante 30 minutos, a quarta amostra foi mantida como recebida. As suspensões de amido foram filtradas, lavadas, secas e analisadas. As modificações oxidativas provocaram mudanças estruturais das moléculas de amido, registradas pelos diferentes resultados calculados a partir das curvas TGA e DTA. A amostra (3) teve as mudanças mais significativas na degradação com o 3ª evento exotérmico com temperaturas acima de 330 °C.

Optimization of an innovative T6 heat treatment for the AlSi10Mg alloy processed by Laser-based Powder Bed Fusion: effect on microstructure, mechanical properties, and tribological behavior

Laser-based Powder Bed Fusion (L-PBF) technology is one of the most commonly used metal Additive Manufacturing (AM) techniques to produce highly customized and value-added parts. The AlSi10Mg alloy has received more attention in the L-PBF process due to its good printability, high strength/weight ratio, corrosion resistance, and relatively low cost. However, a deep understanding of the effect of heat treatments on this alloy's metastable microstructure is still required for developing tailored heat treatments for the L-PBF AlSi10Mg alloy to overcome the limits of the as-built condition. Several authors have already investigated the effects of conventional heat treatment on the microstructure and mechanical behavior of the L-PBF AlSi10Mg alloy but often overlooked the peculiarities of the starting supersatured and ultrafine microstructure induced by rapid solidification. For this reason, the effects of innovative T6 heat treatment (T6R) on the microstructure and mechanical behavior of the L-PBF AlSi10Mg alloy were assessed. The short solution soaking time (10 min) and the relatively low temperature (510 °C) reduced the typical porosity growth at high temperatures and led to a homogeneous distribution of fine globular Si particles in the Al matrix. In addition, it increased the amount of Mg and Si in the solid solution available for precipitation hardening during the aging step. The mechanical (at room temperature and 200 °C) and tribological properties of the T6R alloy were evaluated and compared with other solutions, especially with an optimized direct-aged alloy (T5 alloy). Results showed that the innovative T6R alloy exhibits the best mechanical trade-off between strength and ductility, the highest fatigue strength among the analyzed conditions, and interesting tribological behavior. Furthermore, the high-temperature mechanical performances of the heat-treated L-PBF AlSi10Mg alloy make it suitable for structural components operating in mild service conditions at 200 °C.

Evaluation Of Different Treatment Methods Against Denture Stomatitis: A Randomized Clinical Study.

The aim of this clinical study was to determine the efficacy of Uncaria tomentosa (cat's claw) against denture stomatitis (DS). Fifty patients with DS were randomly assigned into 3 groups to receive 2% miconazole, placebo, or 2% U tomentosa gel. DS level was recorded immediately, after 1 week of treatment, and 1 week after treatment. The clinical effectiveness of each treatment was measured using Newton's criteria. Mycologic samples from palatal mucosa and prosthesis were obtained to determinate colony forming units per milliliter (CFU/mL) and fungal identification at each evaluation period. Candida species were identified with HiCrome Candida and API 20C AUX biochemical test. DS severity decreased in all groups (P < .05). A significant reduction in number of CFU/mL after 1 week (P < .05) was observed for all groups and remained after 14 days (P > .05). C albicans was the most prevalent microorganism before treatment, followed by C tropicalis, C glabrata, and C krusei, regardless of the group and time evaluated. U tomentosa gel had the same effect as 2% miconazole gel. U tomentosa gel is an effective topical adjuvant treatment for denture stomatitis.

Evaluation Of The Effect Of Different Methods Of Microabrasion And Polishing On Surface Roughness Of Dental Enamel.

The microabrasion technique of enamel consists of selectively abrading the discolored areas or causing superficial structural changes in a selective way. In microabrasion technique, abrasive products associated with acids are used, and the evaluation of enamel roughness after this treatment, as well as surface polishing, is necessary. This in-vitro study evaluated the enamel roughness after microabrasion, followed by different polishing techniques. Roughness analyses were performed before microabrasion (L1), after microabrasion (L2), and after polishing (L3).Thus, 60 bovine incisive teeth divided into two groups were selected (n=30): G1- 37% phosphoric acid (37%) (Dentsply) and pumice; G2- hydrochloric acid (6.6%) associated with silicon carbide (Opalustre - Ultradent). Thereafter, the groups were divided into three sub-groups (n=10), according to the system of polishing: A - Fine and superfine granulation aluminum oxide discs (SofLex 3M); B - Diamond Paste (FGM) associated with felt discs (FGM); C - Silicone tips (Enhance - Dentsply). A PROC MIXED procedure was applied after data exploratory analysis, as well as the Tukey-Kramer test (5%). No statistical differences were found between G1 and G2 groups. L2 differed statistically from L1 and showed superior amounts of roughness. Differences in the amounts of post-polishing roughness for specific groups (1A, 2B, and 1C) arose, which demonstrated less roughness in L3 and differed statistically from L2 in the polishing system. All products increased enamel roughness, and the effectiveness of the polishing systems was dependent upon the abrasive used.

Effect Of Daily Use Of An Enzymatic Denture Cleanser On Candida Albicans Biofilms Formed On Polyamide And Poly(methyl Methacrylate) Resins: An In Vitro Study.

Candida biofilms on denture surfaces are substantially reduced after a single immersion in denture cleanser. However, whether this effect is maintained when dentures are immersed in cleanser daily is unclear. The purpose of this study was to evaluate the effect of the daily use of enzymatic cleanser on Candida albicans biofilms on denture base materials. The surfaces of polyamide and poly(methyl methacrylate) resin specimens (n=54) were standardized and divided into 12 groups (n=9 per group), according to study factors (material type, treatment type, and periods of treatment). Candida albicans biofilms were allowed to form over 72 hours, after which the specimens were treated with enzymatic cleanser once daily for 1, 4, or 7 days. Thereafter, residual biofilm was ultrasonically removed and analyzed for viable cells (colony forming units/mm(2)) and enzymatic activity (phospholipase, aspartyl-protease, and hemolysin). Factors that interfered with the response variables were analyzed by 3-way ANOVA with the Holm-Sidak multiple comparison method (α=.05). Polyamide resin presented more viable cells of Candida albicans (P<.001) for both the evaluated treatment types and periods. Although enzymatic cleansing significantly (P<.001) reduced viable cells, daily use did not maintain this reduction (P<.001). Phospholipase activity significantly increased with time (P<.001) for both materials and treatments. However, poly(methyl methacrylate) based resin (P<.001) and enzymatic cleansing treatment (P<.001) contributed to lower phospholipase activity. Aspartyl-protease and hemolysin activities were not influenced by study factors (P>.05). Although daily use of an enzymatic cleanser reduced the number of viable cells and phospholipase activity, this treatment was not effective against residual biofilm over time.