Das Einzugsgebiet der Fulda - Untersuchung der Methoden der Hochwasserstatistik im Zeichen des Klimawandels

Numerous studies have proven an effect of a probable climate change on the hydrosphere’s different subsystems. In the 21st century global and regional redistribution of water has to be expected and it is very likely that extreme weather phenomenon will occur more frequently. From a global view the flood situation will exacerbate. In contrast to these discoveries the classical approach of flood frequency analysis provides terms like “mean flood recurrence interval”. But for this analysis to be valid there is a need for the precondition of stationary distribution parameters which implies that the flood frequencies are constant in time. Newer approaches take into account extreme value distributions with time-dependent parameters. But the latter implies a discard of the mentioned old terminology that has been used up-to-date in engineering hydrology. On the regional scale climate change affects the hydrosphere in various ways. So, the question appears to be whether in central Europe the classical approach of flood frequency analysis is not usable anymore and whether the traditional terminology should be renewed. In the present case study hydro-meteorological time series of the Fulda catchment area (6930 km²), upstream of the gauging station Bonaforth, are analyzed for the time period 1960 to 2100. At first a distributed catchment area model (SWAT2005) is build up, calibrated and finally validated. The Edertal reservoir is regulated as well by a feedback control of the catchments output in case of low water. Due to this intricacy a special modeling strategy has been necessary: The study area is divided into three SWAT basin models and an additional physically-based reservoir model is developed. To further improve the streamflow predictions of the SWAT model, a correction by an artificial neural network (ANN) has been tested successfully which opens a new way to improve hydrological models. With this extension the calibration and validation of the SWAT model for the Fulda catchment area is improved significantly. After calibration of the model for the past 20th century observed streamflow, the SWAT model is driven by high resolution climate data of the regional model REMO using the IPCC scenarios A1B, A2, and B1, to generate future runoff time series for the 21th century for the various sub-basins in the study area. In a second step flood time series HQ(a) are derived from the 21st century runoff time series (scenarios A1B, A2, and B1). Then these flood projections are extensively tested with regard to stationarity, homogeneity and statistical independence. All these tests indicate that the SWAT-predicted 21st-century trends in the flood regime are not significant. Within the projected time the members of the flood time series are proven to be stationary and independent events. Hence, the classical stationary approach of flood frequency analysis can still be used within the Fulda catchment area, notwithstanding the fact that some regional climate change has been predicted using the IPCC scenarios. It should be noted, however, that the present results are not transferable to other catchment areas. Finally a new method is presented that enables the calculation of extreme flood statistics, even if the flood time series is non-stationary and also if the latter exhibits short- and longterm persistence. This method, which is called Flood Series Maximum Analysis here, enables the calculation of maximum design floods for a given risk- or safety level and time period.

"Thematically Analysing Social Network Content During Disasters Through the Lens of the Disaster Management Lifecycle" & "Investigating Similarity Between Privacy Policies of Social Networking Sites as a Precursor for Standardization"

Abstract 1: Social Networks such as Twitter are often used for disseminating and collecting information during natural disasters. The potential for its use in Disaster Management has been acknowledged. However, more nuanced understanding of the communications that take place on social networks are required to more effectively integrate this information into the processes within disaster management. The type and value of information shared should be assessed, determining the benefits and issues, with credibility and reliability as known concerns. Mapping the tweets in relation to the modelled stages of a disaster can be a useful evaluation for determining the benefits/drawbacks of using data from social networks, such as Twitter, in disaster management.A thematic analysis of tweets’ content, language and tone during the UK Storms and Floods 2013/14 was conducted. Manual scripting was used to determine the official sequence of events, and classify the stages of the disaster into the phases of the Disaster Management Lifecycle, to produce a timeline. Twenty- five topics discussed on Twitter emerged, and three key types of tweets, based on the language and tone, were identified. The timeline represents the events of the disaster, according to the Met Office reports, classed into B. Faulkner’s Disaster Management Lifecycle framework. Context is provided when observing the analysed tweets against the timeline. This illustrates a potential basis and benefit for mapping tweets into the Disaster Management Lifecycle phases. Comparing the number of tweets submitted in each month with the timeline, suggests users tweet more as an event heightens and persists. Furthermore, users generally express greater emotion and urgency in their tweets.This paper concludes that the thematic analysis of content on social networks, such as Twitter, can be useful in gaining additional perspectives for disaster management. It demonstrates that mapping tweets into the phases of a Disaster Management Lifecycle model can have benefits in the recovery phase, not just in the response phase, to potentially improve future policies and activities. Abstract2: The current execution of privacy policies, as a mode of communicating information to users, is unsatisfactory. Social networking sites (SNS) exemplify this issue, attracting growing concerns regarding their use of personal data and its effect on user privacy. This demonstrates the need for more informative policies. However, SNS lack the incentives required to improve policies, which is exacerbated by the difficulties of creating a policy that is both concise and compliant. Standardization addresses many of these issues, providing benefits for users and SNS, although it is only possible if policies share attributes which can be standardized. This investigation used thematic analysis and cross- document structure theory, to assess the similarity of attributes between the privacy policies (as available in August 2014), of the six most frequently visited SNS globally. Using the Jaccard similarity coefficient, two types of attribute were measured; the clauses used by SNS and the coverage of forty recommendations made by the UK Information Commissioner’s Office. Analysis showed that whilst similarity in the clauses used was low, similarity in the recommendations covered was high, indicating that SNS use different clauses, but to convey similar information. The analysis also showed that low similarity in the clauses was largely due to differences in semantics, elaboration and functionality between SNS. Therefore, this paper proposes that the policies of SNS already share attributes, indicating the feasibility of standardization and five recommendations are made to begin facilitating this, based on the findings of the investigation.

Polimorfismos del gen Butirilcolinesterasa responsables de reacciones adversas en pacientes consumidores de “cocaína”

La butirilcolinesterasa humana (BChE; EC 3.1.1.8) es una enzima polimórfica sintetizada en el hígado y en el tejido adiposo, ampliamente distribuida en el organismo y encargada de hidrolizar algunos ésteres de colina como la procaína, ésteres alifáticos como el ácido acetilsalicílico, fármacos como la metilprednisolona, el mivacurium y la succinilcolina y drogas de uso y/o abuso como la heroína y la cocaína. Es codificada por el gen BCHE (OMIM 177400), habiéndose identificado más de 100 variantes, algunas no estudiadas plenamente, además de la forma más frecuente, llamada usual o silvestre. Diferentes polimorfismos del gen BCHE se han relacionado con la síntesis de enzimas con niveles variados de actividad catalítica. Las bases moleculares de algunas de esas variantes genéticas han sido reportadas, entre las que se encuentra las variantes Atípica (A), fluoruro-resistente del tipo 1 y 2 (F-1 y F-2), silente (S), Kalow (K), James (J) y Hammersmith (H). En este estudio, en un grupo de pacientes se aplicó el instrumento validado Lifetime Severity Index for Cocaine Use Disorder (LSI-C) para evaluar la gravedad del consumo de “cocaína” a lo largo de la vida. Además, se determinaron Polimorfismos de Nucleótido Simple (SNPs) en el gen BCHE conocidos como responsables de reacciones adversas en pacientes consumidores de “cocaína” mediante secuenciación del gen y se predijo el efecto delos SNPs sobre la función y la estructura de la proteína, mediante el uso de herramientas bio-informáticas. El instrumento LSI-C ofreció resultados en cuatro dimensiones: consumo a lo largo de la vida, consumo reciente, dependencia psicológica e intento de abandono del consumo. Los estudios de análisis molecular permitieron observar dos SNPs codificantes (cSNPs) no sinónimos en el 27.3% de la muestra, c.293A>G (p.Asp98Gly) y c.1699G>A (p.Ala567Thr), localizados en los exones 2 y 4, que corresponden, desde el punto de vista funcional, a la variante Atípica (A) [dbSNP: rs1799807] y a la variante Kalow (K) [dbSNP: rs1803274] de la enzima BChE, respectivamente. Los estudios de predicción In silico establecieron para el SNP p.Asp98Gly un carácter patogénico, mientras que para el SNP p.Ala567Thr, mostraron un comportamiento neutro. El análisis de los resultados permite proponer la existencia de una relación entre polimorfismos o variantes genéticas responsables de una baja actividad catalítica y/o baja concentración plasmática de la enzima BChE y algunas de las reacciones adversas ocurridas en pacientes consumidores de cocaína.

Detection of flood extent in urban areas using high resolution TerraSAR-X data

Flooding is a major hazard in both rural and urban areas worldwide, but it is in urban areas that the impacts are most severe. An investigation of the ability of high resolution TerraSAR-X data to detect flooded regions in urban areas is described. An important application for this would be the calibration and validation of the flood extent predicted by an urban flood inundation model. To date, research on such models has been hampered by lack of suitable distributed validation data. The study uses a 3m resolution TerraSAR-X image of a 1-in-150 year flood near Tewkesbury, UK, in 2007, for which contemporaneous aerial photography exists for validation. The DLR SETES SAR simulator was used in conjunction with airborne LiDAR data to estimate regions of the TerraSAR-X image in which water would not be visible due to radar shadow or layover caused by buildings and taller vegetation, and these regions were masked out in the flood detection process. A semi-automatic algorithm for the detection of floodwater was developed, based on a hybrid approach. Flooding in rural areas adjacent to the urban areas was detected using an active contour model (snake) region-growing algorithm seeded using the un-flooded river channel network, which was applied to the TerraSAR-X image fused with the LiDAR DTM to ensure the smooth variation of heights along the reach. A simpler region-growing approach was used in the urban areas, which was initialized using knowledge of the flood waterline in the rural areas. Seed pixels having low backscatter were identified in the urban areas using supervised classification based on training areas for water taken from the rural flood, and non-water taken from the higher urban areas. Seed pixels were required to have heights less than a spatially-varying height threshold determined from nearby rural waterline heights. Seed pixels were clustered into urban flood regions based on their close proximity, rather than requiring that all pixels in the region should have low backscatter. This approach was taken because it appeared that urban water backscatter values were corrupted in some pixels, perhaps due to contributions from side-lobes of strong reflectors nearby. The TerraSAR-X urban flood extent was validated using the flood extent visible in the aerial photos. It turned out that 76% of the urban water pixels visible to TerraSAR-X were correctly detected, with an associated false positive rate of 25%. If all urban water pixels were considered, including those in shadow and layover regions, these figures fell to 58% and 19% respectively. These findings indicate that TerraSAR-X is capable of providing useful data for the calibration and validation of urban flood inundation models.

Coupled simulations of the Indian monsoon intraseasonal oscillation using a fine-resolution mixed-layer ocean model

The intraseasonal variability (ISV) of the Indian summer monsoon is dominated by a 30–50 day oscillation between “active” and “break” events of enhanced and reduced rainfall over the subcontinent, respectively. These organized convective events form in the equatorial Indian Ocean and propagate north to India. Atmosphere–ocean coupled processes are thought to play a key role the intensity and propagation of these events. A high-resolution, coupled atmosphere–mixed-layer-oceanmodel is assembled: HadKPP. HadKPP comprises the Hadley Centre Atmospheric Model (HadAM3) and the K Profile Parameterization (KPP) mixed-layer ocean model. Following studies that upper-ocean vertical resolution and sub-diurnal coupling frequencies improve the simulation of ISV in SSTs, KPP is run at 1 m vertical resolution near the surface; the atmosphere and ocean are coupled every three hours. HadKPP accurately simulates the 30–50 day ISV in rainfall and SSTs over India and the Bay of Bengal, respectively, but suffers from low ISV on the equator. This is due to the HadAM3 convection scheme producing limited ISV in surface fluxes. HadKPP demonstrates little of the observed northward propagation of intraseasonal events, producing instead a standing oscillation. The lack of equatorial ISV in convection in HadAM3 constrains the ability of KPP to produce equatorial SST anomalies, which further weakens the ISV of convection. It is concluded that while atmosphere–ocean interactions are undoubtedly essential to an accurate simulation of ISV, they are not a panacea for model deficiencies. In regions where the atmospheric forcing is adequate, such as the Bay of Bengal, KPP produces SST anomalies that are comparable to the Tropical Rainfall Measuring Mission Microwave Imager (TMI) SST analyses in both their magnitude and their timing with respect to rainfall anomalies over India. HadKPP also displays a much-improved phase relationship between rainfall and SSTs over a HadAM3 ensemble forced by observed SSTs, when both are compared to observations. Coupling to mixed-layer models such as KPP has the potential to improve operational predictions of ISV, particularly when the persistence time of SST anomalies is shorter than the forecast lead time.

Purpose built teaching equipment for a laboratory based course in three phase machines and drives

The hazards associated with high voltage three phase inverters and the rotating shafts of large electrical machines have resulted in most of the engineering courses covering these topics to be predominantly theoretical. This paper describes a set of purpose built, low voltage and low cost teaching equipment which allows the "hands on" instruction of three phase inverters and rotating machines. By using low voltages, the student can experiment freely with the motors and inverter and can access all of the current and voltage waveforms, which until now could only be studied in text books or observed as part of laboratory demonstrations. Both the motor and the inverter designs are optimized for teaching purposes cost around $25 and can be made with minimal effort.

Three-phase machines and drives - equipment for a laboratory-based course

The hazards associated with high-voltage three-phase inverters and high-powered large electrical machines have resulted in most of the engineering courses covering three-phase machines and drives theoretically. This paper describes a set of purpose-built, low-voltage, and low-cost teaching equipment that allows the hands-on instruction of three-phase inverters and rotating machines. The motivation for moving towards a system running at low voltages is that the students can safely experiment freely with the motors and inverter. The students can also access all of the current and voltage waveforms, which until now could only be studied in textbooks or observed as part of laboratory demonstrations. Both the motor and the inverter designs are for teaching purposes and require minimal effort and cost

Evaluating a new LISFLOOD-FP formulation with data from the summer 2007 floods in Tewkesbury, UK

Two-dimensional flood inundation modelling is a widely used tool to aid flood risk management. In urban areas, where asset value and population density are greatest, the model spatial resolution required to represent flows through a typical street network (i.e. < 10m) often results in impractical computational cost at the whole city scale. Explicit diffusive storage cell models become very inefficient at such high resolutions, relative to shallow water models, because the stable time step in such schemes scales as a quadratic of resolution. This paper presents the calibration and evaluation of a recently developed new formulation of the LISFLOOD-FP model, where stability is controlled by the Courant–Freidrichs–Levy condition for the shallow water equations, such that, the stable time step instead scales linearly with resolution. The case study used is based on observations during the summer 2007 floods in Tewkesbury, UK. Aerial photography is available for model evaluation on three separate days from the 24th to the 31st of July. The model covered a 3.6 km by 2 km domain and was calibrated using gauge data from high flows during the previous month. The new formulation was benchmarked against the original version of the model at 20 m and 40 m resolutions, demonstrating equally accurate performance given the available validation data but at 67x faster computation time. The July event was then simulated at the 2 m resolution of the available airborne LiDAR DEM. This resulted in a significantly more accurate simulation of the drying dynamics compared to that simulated by the coarse resolution models, although estimates of peak inundation depth were similar.

Purpose built teaching equipment for a laboratory based course in three phase machines and drives

The hazards associated with high voltage three phase inverters ond the rotating sha@s of large electrical machines have resulted in most of the engineering courses covering these topics to be predominantly theoretical. This paper describes a set of purpose built, low voltage and low cost teaching equipment which allows the “hands on I’ instruction of three phase inverters and rotating machines. By using low voltages, the student can experiment freely with the motors and inverter and can access all of the current and voltage waveforms, which until now could only be studied in text books or observed as part of laboratory demonstrations. Both the motor and the inverter designs are optimized for teaching purposes, cost around $25 and can be made with minimal effort.

Three-phase machines and drives - Equipment for a laboratory-based course

The hazards associated with high-voltage three-phase inverters and high-powered large electrical machines have resulted in most of the engineering courses covering three-phase machines and drives theoretically. This paper describes a set of purpose-built, low-voltage, and low-cost teaching equipment that allows the hands-on instruction of three-phase inverters and rotating machines. The motivation for moving towards a system running at low voltages is that the students can safely experiment freely with the motors and inverter. The students can also access all of the current and voltage waveforms, which until now could only be studied in textbooks or observed as part of laboratory demonstrations. Both the motor and the inverter designs are for teaching purposes and require minimal effort and cost.

Principles and calibration of solid phase microextraction fibre (passive sampler) for measurements of airflow and air infiltration in dwellings

Tracer gas techniques have been the most appropriate experimental method of determining airflows and ventilation rates in houses. However, current trends to reduce greenhouse gas effects have prompted the need for alternative techniques, such as passive sampling. In this research passive sampling techniques have been used to demonstrate the potential to fulfil these requirements by using solutions of volatile organic compounds (VOCs) and solid phase microextraction (SPME) fibres. These passive sampling techniques have been calibrated against tracer gas decay techniques and measurements from a standard orifice plate. Two constant sources of volatile organic compounds were diffused into two sections of a humidity chamber and sampled using SPME fibres. From a total of four SPME fibres (two in each section), reproducible results were obtained. Emission rates and air movement from one section to the other were predicted using developed algorithms. Comparison of the SPME fibre technique with that of the tracer gas technique and measurements from an orifice plate showed similar results with good precision and accuracy. With these fibres, infiltration rates can be measured over grab samples in a time weighted averaged period lasting from 10 minutes up to several days. Key words: passive samplers, solid phase microextraction fibre, tracer gas techniques, airflow, air infiltration, houses.

Interpretation bias and anxiety in childhood: stability, specificity and longitudinal associations

Background: Biases in the interpretation of ambiguous material are central to cognitive models of anxiety; however, understanding of the association between interpretation and anxiety in childhood is limited. To address this, a prospective investigation of the stability and specificity of anxious cognitions and anxiety and the relationship between these factors was conducted. Method: Sixty-five children (10–11 years) from a community sample completed measures of self-reported anxiety, depression, and conduct problems, and responded to ambiguous stories at three time points over one-year. Results: Individual differences in biases in interpretation of ambiguity (specifically “anticipated distress” and “threat interpretation”) were stable over time. Furthermore, anticipated distress and threat interpretation were specifically associated with anxiety symptoms. Distress anticipation predicted change in anxiety symptoms over time. In contrast, anxiety scores predicted change in threat interpretation over time. Conclusions: The results suggest that different cognitive constructs may show different longitudinal links with anxiety. These preliminary findings extend research and theory on anxious cognitions and their link with anxiety in children, and suggest that these cognitive processes may be valuable targets for assessment and intervention.

Calibration and bias correction of climate projections for crop modelling: an idealised case study over Europe

Producing projections of future crop yields requires careful thought about the appropriate use of atmosphere-ocean global climate model (AOGCM) simulations. Here we describe and demonstrate multiple methods for ‘calibrating’ climate projections using an ensemble of AOGCM simulations in a ‘perfect sibling’ framework. Crucially, this type of analysis assesses the ability of each calibration methodology to produce reliable estimates of future climate, which is not possible just using historical observations. This type of approach could be more widely adopted for assessing calibration methodologies for crop modelling. The calibration methods assessed include the commonly used ‘delta’ (change factor) and ‘nudging’ (bias correction) approaches. We focus on daily maximum temperature in summer over Europe for this idealised case study, but the methods can be generalised to other variables and other regions. The calibration methods, which are relatively easy to implement given appropriate observations, produce more robust projections of future daily maximum temperatures and heat stress than using raw model output. The choice over which calibration method to use will likely depend on the situation, but change factor approaches tend to perform best in our examples. Finally, we demonstrate that the uncertainty due to the choice of calibration methodology is a significant contributor to the total uncertainty in future climate projections for impact studies. We conclude that utilising a variety of calibration methods on output from a wide range of AOGCMs is essential to produce climate data that will ensure robust and reliable crop yield projections.

Mid-term evaluation of African Technology Policy Studies Network Phase VI Strategic Plan: for the period January 1, 2009 to December 31, 2010

The African Technology Policy Studies Network (ATPS) is a multidisciplinary network of researchers, private sector actors, policymakers and civil society. ATPS has the vision to become the leading international centre of excellence and reference in science, technology and innovation (STI) systems research, training and capacity building, communication and sensitization, knowledge brokerage, policy advocacy and outreach in Africa. It has a Regional Secretariat in Nairobi Kenya, and operates through national chapters in 29 countries (including 27 in Africa and two Chapters in the United Kingdom and USA for Africans in the Diaspora) with an expansion plan to cover the entire continent by 2015. The ATPS Phase VI Strategic Plan aims to improve the understanding and functioning of STI processes and systems to strengthen the learning capacity, social responses, and governance of STI for addressing Africa's development challenges, with a specific focus on the Millennium Development Goals (MDGs). A team of external evaluators carried out a midterm review to assess the effectiveness and efficiency of the implementation of the Strategic Plan for the period January 1, 2009 to December 31, 2010. The evaluation methodology involved multiple quantitative and qualitative methods to assess the qualitative and quantitative inputs (human resources, financial resources, time, etc.) into ATPS activities (both thematic and facilitative) and their tangible and intangible outputs, outcomes and impacts. Methods included a questionnaire survey of ATPS members and stakeholders, key informant interviews, and focus group discussions (FGDs) with members in six countries. Effectiveness of Programmes Under all six strategic goals, very good progress has been made towards planned outputs and outcomes. This is evidenced by key performance indicators (KPIs) generated from desk review, ratings from the survey respondents, and the themes that run through the FGDs. Institutional and Programme Cost Effectiveness Institutional Effectiveness: assessment of institutional effectiveness suggests that adequate management frameworks are in place and are being used effectively and transparently. Also technical and financial accounting mechanisms are being followed in accordance with grant agreements and with global good practice. This is evidenced by KPIs generated from desk review. Programme Cost Effectiveness: assessment of cost-effectiveness of execution of programmes shows that organisational structure is efficient, delivering high quality, relevant research at relatively low cost by international standards. The evidence includes KPIs from desk review: administrative costs to programme cost ratio has fallen steadily, to around 10%; average size of research grants is modest, without compromising quality. There is high level of pro bono input by ATPS members. ATPS Programmes Strategic Evaluation ATPS research and STI related activities are indeed unique and well aligned with STI issues and needs facing Africa and globally. The multi-disciplinary and trans-boundary nature of the research activities are creating a unique group of research scientists. The ATPS approach to research and STI issues is paving the way for the so called Third Generation University (3GU). Understanding this unique positioning, an increasing number of international multilateral agencies are seeking partnership with ATPS. ATPS is seeing an increasing level of funding commitments by Donor Partners. Recommendations for ATPS Continued Growth and Effectiveness On-going reform of ATPS administrative structure to continue The on-going reforms that have taken place within the Board, Regional Secretariat, and at the National Chapter coordination levels are welcomed. Such reform should continue until fully functional corporate governance policy and practices are fully established and implemented across the ATPS governance structures. This will further strengthen ATPS to achieve the vision of being the leading STI policy brokerage organization in Africa. Although training in corporate governance has been carried out for all sectors of ATPS leadership structure in recent time, there is some evidence that these systems have not yet been fully implemented effectively within all the governance structures of the organization, especially at the Board and National chapter levels. Future training should emphasize practical application with exercises relevant to ATPS leadership structure from the Board to the National Chapter levels. Training on Transformational Leadership - Leading a Change Though a subject of intense debate amongst economists and social scientists, it is generally agreed that cultural mindsets and attitudes could enhance and/or hinder organizational progress. ATPS’s vision demands transformational leadership skills amongst its leaders from the Board members to the National Chapter Coordinators. To lead such a change, ATPS leaders must understand and avoid personal and cultural mindsets and value systems that hinder change, while embracing those that enhance it. It requires deliberate assessment of cultural, behavioural patterns that could hinder progress and the willingness to be recast into cultural and personal habits that make for progress. Improvement of relationship amongst the Board, Secretariat, and National Chapters A large number of ATPS members and stakeholders feel they do not have effective communications and/or access to Board, National Chapter Coordinators and Regional Secretariat activities. Effort should be made to improve the implementation of ATPS communication strategy to improve on information flows amongst the ATPS management and the members. The results of the survey and the FGDs suggest that progress has been made during the past two years in this direction, but more could be done to ensure effective flow of pertinent information to members following ATPS communications channels. Strategies for Increased Funding for National Chapters There is a big gap between the fundraising skills of the Regional Secretariat and those of the National Coordinators. In some cases, funds successfully raised by the Secretariat and disbursed to national chapters were not followed up with timely progress and financial reports by some national chapters. Adequate training in relevant skills required for effective interactions with STI key policy players should be conducted regularly for National Chapter coordinators and ATPS members. The ongoing training in grant writing should continue and be made continent-wide if funding permits. Funding of National Chapters should be strategic such that capacity in a specific area of research is built which, with time, will not only lead to a strong research capacity in that area, but also strengthen academic programmes. For example, a strong climate change programme is emerging at University of Nigeria Nsukka (UNN), with strong collaborations with Universities from neighbouring States. Strategies to Increase National Government buy-in and support for STI Translating STI research outcomes into policies requires a great deal of emotional intelligence, skills which are often lacking in the first and second generation universities. In the epoch of the science-based or 2GUs, governments were content with universities carrying out scientific research and providing scientific education. Now they desire to see universities as incubators of new science- or technology-based commercial activities, whether by existing firms or start-ups. Hence, governments demand that universities take an active and leading role in the exploitation of their knowledge and they are willing to make funds available to support such activities. Thus, for universities to gain the attention of national leadership they must become centres of excellence and explicit instruments of economic development in the knowledge-based economy. The universities must do this while working collaboratively with government departments, parastatals, and institutions and dedicated research establishments. ATPS should anticipate these shifting changes and devise programmes to assist both government and universities to relate effectively. New administrative structures in member organizations to sustain and manage the emerging STI multidisciplinary teams Second Generation universities (2GUs) tend to focus on pure science and often do not regard the application of their know-how as their task. In contrast, Third Generation Universities (3GUs) objectively stimulate techno-starters – students or academics – to pursue the exploitation or commercialisation of the knowledge they generate. They view this as being equal in importance to the objectives of scientific research and education. Administratively, research in the 2GU era was mainly monodisciplinary and departments were structured along disciplines. The emerging interdisciplinary scientific teams with focus on specific research areas functionally work against the current mono-disciplinary faculty-based, administrative structure of 2GUs. For interdisciplinary teams, the current faculty system is an obstacle. There is a need for new organisational forms for university management that can create responsibilities for the task of know-how exploitation. ATPS must anticipate this and begin to strategize solutions for their member institutions to transition to 3Gus administrative structure, otherwise ATPS growth will plateau, and progress achieved so far may be stunted.