Extraction of phosphorus in natural waters and sediments by ignition method

Phosphorus recoveries from selected inorganic and organic P-containing compounds after ignition with auxiliaries, such as MgSO4, Mg (NO3)(2), MgCl2, Mg (Ac)(2) and CaCl2 were studied. It was found that the phosphorus could not be completely recovered when most P-containing compounds were ignited with MgSO4 at temperature not higher than 500degreesC if the baked residue was extracted with 0.2 mol/L HCl for 30 min at 80degreesC or at room temperature. In contrast, MgCl2, Mg(Ac)(2) and CaCl2, as well as Mg(NO3)(2), could all yield complete P recoveries. We suggest that MgCl2 rather than MgSO4, which is usually used, should be utilized as ashing auxiliary agent in the P extraction by ignition method. Although Mg (NO3)(2) is a highly effective auxiliary agent, yet interference from MgSO4, danger of explosion, toxicity of nitrogen dioxide and more manipulation steps may limit its widespread utilization. It is suggested that if sediment is ignited with MgCl2, the extraction of residue with 0.2 mol/L HCl for 30 min at 80degreesC could give good result.

PCBs and its coupling with eco-environments in Southern Yellow Sea surface sediments

In this paper, the spatial distribution and source of the PCBs in surface sediments of the Southern Yellow Sea (SYS) and influencing factors, such as the sediment characteristics (components, relative proportions and total organic carbon contents), and hydrodynamic conditions were analyzed. PCB concentrations in the surface sediments ranged from 518-5848 pg/g, with average values of 1715 pg/g decreasing sharply compared to last year. In the study area, the PCB pollution level in the middle area was the highest, followed by that of the east coast and the west coast, respectively. Although the PCB level in the coastal areas was lower than that in the middle areas, it was proven in our study that the Yellow Sea obtained PCBs by virtue of river inputs. There was a positive and pertinent correlation between the clay proportion and PCB concentrations, and the increase of the PCB concentrations was directly proportional to the increase of TOC contents, with r = 0.61, but it was contrary to the sediment grain size. Consequently, the factors controlling PCB distribution had direct or indirect relationships with sediment grain size; moreover, the hydrodynamic conditions determined the sediment components and grain size. In conclusion, hydrodynamic conditions of the Yellow Sea were the most important influencing factors effecting the distribution of PCBs in the surface sediments of the SYS. (C) 2007 Elsevier Ltd. All rights reserved.

Characteristics of nitrogen forms in the surface sediments of southwestern Nansha Trough, South China Sea

The area of the southwestern Nansha Trough is one of the most productive areas of the southern South China Sea. It is a typical semi-deep sea area of transition from shoal to abyssal zone. To understand distributions and roles of nitrogen forms involved in biogeochemical cycling in this area, contents of nitrogen in four extractable forms: nitrogen in ion exchangeable form (IEF-N), nitrogen in weak acid extractable form (WAEF-N), nitrogen in strong alkali extractable form (SAEF-N) and nitrogen in strong oxidation extractable form (SOEF-N), as well as in total nitrogen content (TN) in surface sediments were determined from samples collected from the cruise in April-May 1999. The study area was divided into three regions (A, B and C) in terms of clay sediment (< 4 mu m) content at < 40%, 40%-60% and > 60%, respectively. Generally, region C was the richest in the nitrogen of all forms and region A the poorest, indicating that the finer the grain size is, the richer the contents of various nitrogen are. The burial efficiency of total nitrogen in surface sediments was 28.79%, indicating that more than 70% of nitrogen had been released and participated in biogeochemical recycling through sediment-water interface.

Investigation of heavy metals in sediments and Manila clams Ruditapes philippinarum from Jiaozhou Bay, China

Manila clams (Ruditapes philippinarum) and sediments were collected bimonthly during 2007 at five locations in Jiaozhou Bay near Qingdao, China, to determine heavy metal concentrations and to assess the validation of R. philippinarum as a metal biomonitor. Concentrations of heavy metals in clam soft tissues ranged between 0.75 and 3.31, 0.89 and 15.20, 5.70 and 26.03, 52.12 and 110.33, 10.30 and 72.34, 9.64 and 28.60, and 3.15 and 52.75 mu g g (-aEuro parts per thousand 1) dry weight for Cd, Pb, Cu, Zn, Mn, Cr, and Ni, respectively. Most of the highest values occurred at the northeast bay and the lowest values occurred at the western part. Regarding seasonal variation, relatively high tissue metal concentrations were observed during October or December. A similar pattern was also found in habitat sediments. There was a strong correlation between the concentrations of Cd, Pb, Zn, Mn, Cr, and Ni in soft tissues and surrounding sediments. It is indicated that R. philippinarum could be used as a biomonitor for heavy metal contamination in Jiaozhou Bay.

Inorganic carbon of sediments in the Yangtze River Estuary and Jiaozhou Bay

JGOFS results showed that the ocean is a major sink for the increasing atmospheric carbon dioxide resulting from human activity. However, the role of the coastal seas in the global carbon cycling is poorly understood. In the present work, the inorganic carbon (IC) in the Yangtze River Estuary and Jiaozhou Bay are studied as examples of offshore sediments. Sequential extraction was used to divide inorganic carbon in the sediments into five forms, NaCl form, NH3 H2O form, NaOH form, NH2OH HCl form and HCl form. Studied of their content and influencing factors were also showed that NaCl form < NH3 H2O form < NaOH form < NH2OH HCl form < HCl form, and that their influencing factors of pH, Eh, Es, water content, organic carbon, organic nitrogen, inorganic nitrogen, organic phosphorus and inorganic phosphorus on inorganic carbon can be divided into two groups, and that every factor has different influence on different form or on the same form in different environment. Different IC form may transform into each other in the early diagenetic process of sediment, but NaCl form, NH3 H2O form, NaOH form and NH2OH HCl form may convert to HCl form ultimately. So every IC form has different contribution to carbon cycling. This study showed that the contribution of various form of IC to the carbon cycle is in the order of NaOH form > NH2OH HCl form > NH3 H2O form > NaCl form > HCl form, and that the contribution of HCl form contributes little to carbon cycling, HCl form may be one of end-result of atmospheric CO2. So Yangtze River estuary sediment may absorb at least about 40.96x10(11) g atmospheric CO2 every year, which indicated that offshore sediment play an important role in absorbing atmospheric CO2.

Seasonal variations in growth and clearance rate of the Zhikong scallop Chlamys farreri suspended in the deep water of Haizhou Bay, China

The growth and survival of the Zhikong scallop Chlamys farreri suspended in deep water of Haizhou Bay were studied from July 2007 to June 2008, and the biodeposition method was used to estimate the clearance rate of C. farreri under field conditions. Results showed that the scallop grew fast during all the culture time, with the exception of summer. The condition index of the scallop increased with time and reached the highest value in spring of the second year. The survival of scallops was 60.8 +/- A 3.9% at the end of this study, mortality occurring mainly during the summer and autumn of the first year. The clearance rate fluctuated obviously with season,with the highest value in September 2007, and the lowest value in March 2008. Factors accounting for variations in growth and clearance rate of scallops are also discussed.

The distribution, enrichment and source of potential harmful elements in surface sediments of Bohai Bay, North China

A geochemical study of Bohai Bay surface sediments was carried out to analyze the potential harmful element (PHE: Ge, Mo, In, Sn, Sb,Te, Tl, Bi and V) concentrations, transportation and deposition, enrichment factors and sources. Germanium, Mo, In, Sn, Sb, Te, Tl, Bi and V concentrations in the surface sediments were: 1.43-1.71, 0.52-1.43, 0.04-0.12, 2.77-4.14, 1.14-2.29, 0.027-0.085, 0.506-0.770, 0.27-0.63 and 70.35-115.90 mu g/g, respectively. The distributions of total PHE concentrations, together with sequential extraction analyses, showed that the PHEs were mainly due to natural inputs from the continental weathering delivered to the bay by rivers and atmospheric transportation and deposition. However, high Mo, Sb, Te, Bi and V occurred in non-residual fractions, suggesting some anthropogenic inputs in addition to the natural inputs. Besides sources, the distributions of PHEs were influenced by the coupling of physical, chemical and biological processes. Enrichment factor (EF) was computed for each site for each element in order to assess the polluting elements and the degree of pollution at each site. Results revealed that the EFs were generally lower than 1.0, particularly for Ge, Mo, In, Sn, Tl and V; however, the EFs were higher (>1.5), particularly for Sb, Te and Bi, revealing moderate contamination. (C) 2010 Elsevier B.V. All rights reserved.

Sources and distribution of aliphatic and polyaromatic hydrocarbons in sediments of Jiaozhou Bay, Qingdao, China

The composition and distribution of aliphatic (n-alkanes) and polyaromatic hydrocarbons (PAHs) were measured for the surface sediments collected at 25 sites from Jiaozhou Bay, Qingdao, China. Total n-alkanes and PAH concentrations ranged from 0.5 to 8.2 mu g/gdw and 0.02 to 2.2 mu g/gdw, respectively, and the distribution of both n-alkanes and PAHs showed large spatial variations in the bay. The distribution of PAHs in the sediments was predominated by the three or more ring compounds. High hydrocarbon levels were generally found in the areas associated with high anthropogenic impact and port activities in the bay. The calculated hydrocarbon indexes suggest that petroleum contamination was the main source of n-alkanes, while both pyrolytic and petrogenic sources contributed PAHs to the surface sediments of Jiaozhou Bay. In comparison to other polluted coastal sediments, the level of contamination from both aliphatic hydrocarbons and PAHs in Jiaozhou Bay sediments is relatively low at the present time. (c) 2005 Elsevier Ltd. All rights reserved.

Geochemieal records of phosphorus in Jiaozhou Bay sediments - Implications for environmental changes in recent hundred years

Phosphorus is a key element and plays an important role in global biogeochemical cycles. The evolution of sedimentary environment is also influenced by phosphorus concentrations and fractions as well as phosphate sorption characteristics of the marine sediments. The geochemical characteristics of phosphorus and their environmental records were presented in Jiaozhou Bay sediments. Profiles of different forms of phosphorus were measured as well as the roles and vertical distributions of phosphorus forms in response to sedimentary environment changes were investigated. The results showed that inorganic phosphorus ( IP) was the major fraction of total phosphorus ( TP); phosphorus which is bound to calcium, iron and occluded phosphorus, as well as the exchangeable phosphorus were the main forms of IP, especially calcium-phosphorus, including detrital carbonate-bound phosphorus ( Det - P) and authigenic apatite-bound phosphorus ( ACa - P), are the uppermost constituent of IP in Jiaozhou Bay sediments. Moreover, the lead-210 chronology technology was employed to estimate how much phosphorus was buried ultimately in sediments. And the research showed that the impacts of human activities have increased remarkably in recent years especially between the 1980s and 2000. According to research, the development of Jiaozhou Bay environment in the past hundred years can be divided into three stages; (I) before the 1980s characterized by the relatively low sedimentation rate, weak land-derived phosphorus inputs and low anthropogenic impacts; (2) from the 1980s to around 2000, accelerating in the 1990s, during which high sedimentation rates, high phosphorus abundance and burial fluxes due to the severe: human activities impacted on the whole environmental system; (3) after 2000, the period of the improvement of environment, the whole system has been improved including the decreasing sedimentation rates, concentration and the burial fluxes of phosphonas.

Assessment of metal contamination in surface sediments of Jiaozhou Bay, Qingdao, China

An assessment of metal contamination in surface sediments of the Jiaozhou Bay, Qingdao, one of the rapidly developing coastal economic zones in China, is provided. Sediments were collected from 10 stations and a total of 15 heavy metals were analyzed. Concentrations of metals show significant variability and range from 210 to 620 ppm for Ti, 2.7 to 23 ppm for Ni, 4.2 to 28 ppm for Cu, 5.2 to 18 ppm for Pb, 12 to 58 ppm for Zn, 0.03 to 0.11 ppm for Cd, 5 to 51 ppm for Cr, 1.5 to 9.9 ppm for Co, 5.3 to 19 ppm for As, 12 to 32 ppm for Se, and 19 to 97 ppm for Sr. Based on concentration relationships and enrichment factor (EF) analyses, the results indicate that sediment grain size and organic matter played important roles in controlling the distribution of the heavy metals in surface sediments of the Jiaozhou Bay. The study shows that the sediment of the Jiaozhou Bay has been contaminated by heavy metals to various degrees, with prominent arsenic contributing the most to the contamination. The analysis suggests that the major sources of metal contamination in the Jiaozhou Bay are land-based anthropogenic ones, such as discharge of industrial waste water and municipal sewage and run-off. Notably, the elevated heavy metal concentrations of the Jiaozhou Bay sediments could have a significant impact on the bay's ecosystem. With the rapid economic development and urbanization around the Jiaozhou Bay, coastal management and pollution control should focus on these contaminant sources, as well as provide ongoing monitoring studies of heavy metal contamination within the bay.

Simultaneous enumeration of diatom, protozoa and meiobenthos from marine sediments using Ludox-QPS method

The Ludox-QPS method is a newly developed technique, which combines the Ludox HS 40 density centrifugation and quantitative protargol stain, to enumerate marine ciliates with good taxonomic resolution. We tested the method for simultaneous enumeration of diatoms, protozoa and meiobenthos and compared its extraction efficiency for meiobenthos with that of the routine Ludox-TM centrifugation and a modified protocol using Ludox HS 40. We conducted the evaluation with a sample size of 8.3 ml each from sandy, muddy-sand and muddy sediments collected from the intertidal area of the Yellow Sea in summer 2006 and spring 2007. The Ludox-QPS method not only produced high extraction efficiencies of 97 +/- 1.3% for diatoms and 97.6 +/- 0.8% for ciliates, indicating a reliable enumeration for eukaryotic microbenthos, but also produced excellent extraction efficiencies of on average 97.3% for total meiobenthos, 97.9% for nematodes and 97.8% for copepods from sands, muddy sands and mud. By contrast, the routine Ludox-TM centrifugation obtained only about 74% of total meiobenthos abundance with one extraction cycle, and the modified Ludox HS 40 centrifugation yielded on average 93% of total meiobenthos: 89.4 +/- 2.0% from sands, 93 +/- 4.1% from muddy sands and 97.1 +/- 3.0% from mud. Apart from the sediment type, sample volume was another important factor affecting the extraction efficiency for meiobenthos. The extraction rate was increased to about 96.4% when using the same modified Ludox centrifugation for a 4 ml sediment sample. Besides the excellent extraction efficiency, the Ludox-QPS method obtained higher abundances of meiobenthos, in particular nematodes, than the routine Ludox centrifugation, which frequently resulted in an uncertain loss of small meiobenthos during the sieving process. Statistical analyses demonstrated that there were no significant differences between the meiobenthos communities revealed by the Ludox-QPS method and the modified Ludox HS 40 centrifugation, showing the high efficiency of the Ludox-QPS method for simultaneous enumeration of diatom, protozoa and meiobenthos. Moreover, the comparatively high taxonomic resolution of the method, especially for diatoms and ciliates, makes it feasible to investigate microbial ecology at community level.

Holosticha hamulata n. sp and Holosticha heterofoissneri Hu and Song, 2001, two urostylid ciliates (Protozoa, Ciliophora) from intertidal sediments of the Yellow Sea

Two marine urostylid ciliates, Holosticha hamulata n. sp. and Holosticha heterofoissneri Hu and Song, 2001, were investigated using live observation and protargol impregnation. Both species were isolated from Korean intertidal sediments of the Yellow Sea. Holosticha hamulata measures about 150 x 25 pro in vivo, and is characterized by a tripartite body shape with a narrow head, an inflated trunk, and a tail that distally projects ventrally forming a hook-like structure. It is the characteristic body shape that distinguishes H. hamulata distinctly from congeners. Holosticha hamulata differs from H. heterofoissneri, possibly the nearest relative, also by the location of the contractile vacuole (ahead of mid-body versus near posterior body third) and the configuration of the macronucleus (on average, 33 scattered nodules assuming a Y-shape versus 17 nodules that may form a U shape). The average number of the macronuclear nodules is a pronounced feature showing great consistency in populations of each species. However, their arrangement is variable in H. heterofoissneri where the nodules are basically scattered or connected by fine fibers forming an elongate U-shape. The location of the contractile vacuole as a taxonomic feature is discussed and a dichotomous key to the species of Holosticha sensu stricto is provided.

Morphology and infraciliature of three species of Metaurostylopsis (Ciliophora, Stichotrichia): M. songi n. sp., M. salina n. sp., and M. marina (Kahl 1932) from sediments, saline ponds, and coastal waters.

Two new urostylid ciliates, Metaurostylopsis songi n. sp. and Metaurostylopsis salina n. sp. and Metaurostylopsis marina (Kahl 1932) are investigated using live observation and protargol impregnation. These species were isolated in Korea from intertidal sediments, saline ponds, and coastal waters. Metaurostylopsis songi is in vivo about 120 pm x 25 mu m, has a slenderly ellipsoidal body, colorless cortical granules in rows on ventral and dorsal body sides, about 54 macronuclear nodules, 28-47 adoral membranelles, five frontal, two or three frontoterminal and six or seven transverse cirri, and 9-12 midventral cirral pairs followed posteriorly by 1-3 single cirri. In vivo M. salina is about 60 pin x 25 mu m, has a pyriform body, colorless cortical granules irregularly arranged, about 45 macronuclear nodules, 18-23 adoral membranelles, three frontal, three to five frontoterminal and two to five transverse cirri, and four or five midventral cirral pairs followed posteriorly by five to seven single cirri. Both species have three marginal cirral rows on each body side and 3 long dorsal kineties. The Korean specimens of M. marina match the Chinese population in all main features. Metaurostylopsis songi differs from M. marina by the more slender body, the number of frontal cirri (invariably five vs. four), and the arrangement of cortical granules (in rows on dorsal and ventral cortex vs. only along dorsal kinetics and anterior body margin). Metaurostylopsis salina differs from its congeners by the distinctly smaller size, the pyriform body shape, the scattered cortical granules (vs. in rows), and number of frontal cirri. It differs from M. marina also by the number of midventral cirral pairs (four or five vs. seven to 11).

Study on steel corrosion in different seabed sediments

A series of simulation experiments on carbon steel (A(3) steel) and low alloy steel (16 Mn steel) in marine atmosphere (MA), seawater (SW) and seabed sediment (SBS) including rough sea sand, fine sea sand and seabed mud were carried out indoors for a year or so by means of individually hanging plates (IHP) and electrically connected hanging plates (ECHP). The corrosion of steels in SBS was mainly due to the macrogalvanic cell effect. The steel plates at the bottom of SBS, as the anode of a macrogalvanic cell, showed the heaviest corrosion with a corrosion rate of up to 0.12 mm/a, approximately equal to that of steel plates in marine atmosphere. The test results showed that the corrosion rates of A(3) and 16 Mn steel in marine environment were in the order: MA > SW > SBS by the IHP method; and MA > SBS > SW by the ECHP method. The corrosion rates of steels in the water/sediment interface were directly proportional to the grain size of the SBS by the ECHP method, but those of steels in the water/sediment interface did not vary with the grain size of SBS by the IHP method. The corrosion rate of low-alloy steel was a little higher than that of carbon steel. The results of this study have important applications for design of offshore steel structures such as oil platform, pier, and port.

细粒沉积物多组分粒度特征及其成因机制研究

By using high-resolution laser grain size instrument Mastersizer 2000, the grain size distribution of windblown depositions (loess and sandy dunes), aqueous sediments (lake, river, riverside and foreshore sand), weathering crust, sloping materials and other fine-grain sediments are systemically measured. The multimodal characteristics of grain size distribution of these sediments are carefully studied. The standard patterns and their grain size characteristics of various sediments are systemically summarized. The discrepancies of multimodal distribution among windblown depositions, aqueous sediments and other sediments are concluded and the physical mechanisms of grain size multimodal distribution of various sediments are also discussed in this paper. The major conclusions are followed: 1. The multimodal characteristic of grain size distribution is a common feature in all sediments and results from properties of transportation medium, dynamic intensity, transportation manner and other factors. 2. The windblown depositions are controlled by aerodynamic forcing, resulting in that the median size of the predominant mode gradually decreases form sandy dunes to loess. Similarly, the aqueous sediments are impacted by dynamic forces of water currents and the median grain size of the predominant mode decreases gradually from river to lake sediments. Because the kinetic viscidity of air is lower than of water, the grain size of modes of windblown depositions is usually finer than that of corresponding modes of aqueous sediments. Typical characteristics of sediments grain size distribution of various sediments have been summarized in the paper: (1) Suspended particles which diameters are less than 75μm are dominant in loess and dust. There are three modes in loess’ grain size distribution: fine, median and coarse (the median size is <1μm、1-10μm、10-75μm, respectively). The coarse mode which percentage is larger than that of others is controlled by source distance and aerodynamic intensity of dust source areas. Some samples also have a saltation mode which median size is about 300-500μm. Our analysis demonstrates that the interaction of wind, atmospheric turbulence, and dust grain gravity along the dust transportation path results in a multimodal grain size distribution for suspended dust. Changes in the median sizes of the coarse and medium modes are related to variation in aerodynamic forcing (lift force related to vertical wind and turbulence) during dust entrainment in the source area and turbulence intensity in the depositional area. (2) There is a predominant coarse saltation mode in grain size distribution of sandy dunes, which median size is about 100-300μm and the content is larger than that of other modes. The grain size distribution curve is near axis symmetric as a standard logarithm normal function. There are some suspended particles in some samples of sandy dunes, which distribution of the fine part is similar to that of loess. Comparing with sandy samples of river sediments, the sorting property of sandy dunes is better than of river samples although both they are the saltation mode. Thus, the sorting property is a criterion to distinguish dune sands and river sands. (3) There are 5~6 modes (median size are <1μm, 1-10μm, 10-70μm, 70-150μm, 150-400μm, >400μm respectively) in grain size distribution of lacustrine sediments. The former 4 modes are suspensive and others are saltated. Lacustrine sediments can be divided into three types: lake shore facies, transitional facies and central lake facies. The grain size distributions of the three facies are distinctly different and, at the same time, the transition among three modes is also clear. In all these modes, the third mode is a criteria to identify the windblown deposition in the watershed. In lake shore sediments, suspended particles are dominant, a saltation mode sometimes occurs and the fourth mode is the most important mode. In the transitional facies, the percentage of the fourth mode decreases and that of the second mode increases from lake shore to central lake. In the central lake facies, the second mode is dominant. A higher content of the second mode indicates its position more close to the central lake. (4) The grain size distribution of river sediments is the most complex. It consist of suspension, saltation and rolling modes. In most situations, the percentage of the saltation mode is larger than that of other modes. The percentage of suspension modes of river sediments is more than of sandy dunes. The grain size distribution of river sediments indicates dynamic strength of river currents. If the fourth mode is dominant, the dynamic forcing of river is weaker, such as in river floodplain. If the five or sixth mode is dominant, the water dynamic forcing of rivers is strong. (5) Sediments can be changed by later forcing in different degree to form some complicated deposition types. In the paper, the grain size distribution of aqueous sediments of windblown deposition, windblown sediments of aqueous deposition, weathering crust and slope materials are discussed and analyzed. 3. The grain size distribution characteristics of different sediments are concluded: (1) Modal difference: Usually there are suspended and saltation modes in the windblown deposition. The third mode is dominant in loess dust and the fifth mode is predominant in sandy dunes. There are suspended, saltation and rolling particles in aqueous sediments. In lacustrine sediments, the second and fourth mode are predominant for central lake facies or lake shore facies, respectively. In river sediments, the fourth, or fifth, or sixth mode is predominant. Suspended modes: the grain size of suspended particles of windblown depositions usually is less than 75μm. The content of suspended particles is lower or none in sandy dunes. However, suspended particles of aqueous sediments may reach 150μm. Difference in grain size of suspended modes represents difference between transitional mediums and the strength of dynamic forcing. Saltation modes: the median size of saltation mode of sandy dunes fluctuates less than that of river sediments. (2) Loess dust and lacustrine sediment: Their suspended particles are clearly different. There is an obvious pit between the second and the third modes in grain size distribution of lacustrine sediments. The phenomenon doesn’t occur in loess dust. In lacustrine sediments, the second mode can be a dominant mode, such as central lake facies, and contents of the second and the third modes change reversely. However, the percentage of the third mode is always the highest in loess dust. (3) Dune Sand and fluvial sand: In these two depositions, the saltation particles are dominant and the median sizes of their saltation modes overlay in distribution range. The fifth mode of dune sand fluctuates is sorted better than that of fluvial sand. (4) Lacustrine and fluvial sediments: In lacustrine sediments, there are 5-6 modes and suspended particles can be predominant. The second mode is dominant in central lake facies and the third mode is dominant in lake shore facies. Saltation or roll modes occurred in central lake facies may indicate strong precipitation events. In fluvial sediments, saltation particles (or rolling particles) usually dominant. 4. A estimation model of lake depth is firstly established by using contents of the second, the third and the fourth modes. 5. The paleoenvironmental history of the eastern part of SongLiao basin is also discussed by analyzing the grain size distribution of Yushu loess-like sediments in Jilin. It was found that there is a tectonic movement before 40ka B.P. in SongLiao basin. After the movement, loess dust deposited in Yushu area as keerqin desert developed. In recent 2000 years, the climate became drier and more deserts activated in the eastern part of Song-Liao basin.