Ultra high pressure homogenization (UHPH) inactivation of Bacillus amyloliquefaciens spores in phosphate buffered saline (PBS) and milk

Ultra high pressure homogenization (UHPH) opens up new areas for dynamic high pressure assisted thermal sterilization of liquids. Bacillus amyloliquefaciens spores are resistant to high isostatic pressure and temperature and were suggested as potential surrogate for high pressure thermal sterilization validation. B. amyloliquefaciens spores suspended in PBS buffer (0.01 M, pH 7.0), low fat milk (1.5%, pH 6.7), and whole milk (3.5%, pH 6.7) at initial concentration of similar to 10(6) CFU/mL were subjected to UHPH treatments at 200, 300, and 350 MPa with an inlet temperature at similar to 80 degrees C. Thermal inactivation kinetics of B. amyloliquefaciens spores in PBS and milk were assessed with thin wall glass capillaries and modeled using first-order and Weibull models. The residence time during UHPH treatments was estimated to determine the contribution of temperature to spore inactivation by UHPH. No sublethal injury was detected after UHPH treatments using sodium chloride as selective component in the nutrient agar medium. The inactivation profiles of spores in PBS buffer and milk were compared and fat provided no clear protective effect for spores against treatments. Treatment at 200 MPa with valve temperatures lower than 125 degrees C caused no reduction of spores. A reduction of 3.5 log(10)CFU/mL of B. amyloliquefaciens spores was achieved by treatment at 350 MPa with a valve temperature higher than 150 degrees C. The modeled thermal inactivation and observed inactivation during UHPH treatments suggest that temperature could be the main lethal effect driving inactivation.

Assessing nut germination protocols for macadamia cultivar 'Beaumont'

A rapid rate and high percentage of macadamia nut germination, together with production of vigorous seedlings, are required by nurseries and breeding programs. Germination of nuts is typically protracted, however, and rarely reaches 100%. Many studies have been conducted into macadamia germination, but most have assessed percent germination only. This study investigated the effects of various treatments on percent germination, germination rate, and plant, shoot and root dry weights. The treatments tested were combinations of: (i) soaking or not soaking seeds in a dilute fungicide solution prior to planting; (ii) four different planting media; and (iii) leaving seed trays open or placing them inside clear plastic bags. For freshly harvested nuts, sowing in potting mix under clear plastic and without soaking produced the highest percent germination and germination rate, the largest shoots, and longest lateral roots.

Floral expression and pollen germination ability in productive mountain papaya ( Vasconcellea pubescens A.DC.) orchards

Mountain papaya ( Vasconcellea pubescens A.DC.) is described as trioecious in the centers of origin of Ecuador, Colombia, and Peru. However, under cultivation conditions in La Serena (30° S, 70° W), Chile, it is found to be dioecious and monoecious. The objective was to learn about the variations in floral expression of mountain papaya. Flowers from monoecious and dioecious plants were therefore identified and quantified during two seasons. In vitro pollen germination ability was also evaluated based on the factors of site, season, and plant sex. Monoecious plant inflorescences are polygamous; female and male flowers are observed, as well as bisexual flowers that are usually deformed. This condition allows them to be classified as an ambisexual plant. The existence of flowers of different sexes appears to depend on the season; the female dioecious plant is maintained as such, independently of climatic conditions. Pollen from male flowers, from both ambisexual and male plants, germinates 75% in summer, while germination decreases to 56% in spring (P ≤ 0.05). Flowering of female plants coincides with the permanent occurrence of male flowers in ambisexual plants, which ensures pollination without the need for male plants as pollinators in orchards. Based on this information, some management practices and possible lines of research about this species are proposed.

Termoterapia de banana 'Prata-Anã' no controle de podridões em pós-colheita

O objetivo desse estudo foi determinar a tolerância de banana (Musa spp.) 'Prata-Anã' (AAB) e do fungo Colletotrichum musae à termoterapia no controle de podridões em pós-colheita. Experimentos in vivo e in vitro foram instalados em delineamento inteiramente casualizado, seguindo um esquema fatorial 4x5 (temperatura x tempo). Os tratamentos consistiram na imersão dos frutos (buquês) e do fungo (esporos e micélio) em água aquecida a 47, 50, 53 e 56 ºC, durante 0, 3, 6, 9 e 12 min. A exposição dos frutos a 56 ºC durante 9 min causou escurecimento da casca nas extremidades dos frutos, porém, as características físicas e químicas dos frutos não foram alteradas pelos tratamentos. Frutos inoculados e tratados a 56 ºC durante 6 min não apresentaram podridões nem escurecimento da casca, enquanto aqueles não tratados apresentaram 64% da área lesionada / fruto. A partir das combinações 53 ºC / 9 mi. e 56 ºC / 3 min a germinação de esporos foi reduzida para 4% e 0%, respectivamente. A combinação 56 ºC / 12 min reduziu, mas não paralisou o crescimento micelial. O tratamento 56 ºC / 6 min retardou mas não paralisou o crescimento micelial in vitro, porém foi efetivo no controle completo das podridões in vivo. Esse tratamento evitou a manifestação de podridões no inverno (maio), mas não no verão (novembro), mostrando-se influenciado pelas condições climáticas próximas à colheita dos cachos. A termoterapia pode ser recomendada para controle de podridão em pós-colheita de banana devendo ser ajustada para diferentes estações do ano.

A Multifaceted Study of Scedosporium boydii Cell Wall Changes during Germination and Identification of GPI-Anchored Proteins

International audience

Influence of mother plant and seed coat colour on germination success of Retama sphaerocarpa L (Boissier)

Mestrado em Engenharia Florestal e dos Recursos Naturais - Instituto Superior de Agronomia - UL

Effects of dark or of red, blue or white light on germination of subterranean clover seeds

Dry or imbibed seeds of the negatively photoblastic burr burying subterranean clover cv. ‘Seaton Park’ were treated with dark or with red, blue or white light to evaluate the effects of light on seed germination. Dry seeds treated with constant white light, red light or blue light during 8 days and subsequently incubated in dark had final germination and duration of germination reduced, and the distribution of germination changed from highly asymmetric to symmetric respectively. Imbibing seeds incubated under constant blue or white light had final germination strongly reduced seven days after sowing (7.3% and 50.1% of the germination under dark) with significant differences between them. After transferral to dark, true complete recovery of germination of seeds treated with white light was observed 19 days after sowing, but only partial recovery in seeds treated with blue light. Results of dry and imbibed seeds are consistent with no activity of phytochromes, as expected in negatively photoblastic seeds. Results of dry seeds are seemingly contradictory because total germination data imply the inactivity of red and blue light photoreceptors, the opposite being implied by duration and shape of germination. A tentative hypothetical solution for the contradiction is presented. Results of imbibed seeds are fully consistent with cryptochromes but not with phototropins mediation of responses to light of seed germination in ‘Seaton Park’. The ecological and adaptive significance of such responses are discussed in the framework of light attenuation in soil and the requirement and ability of subterranean clover ‘Seaton Park’ to bury seeds.

DETECTION OF SPORES AND HYPHAE OF ARTWORKS’ BIODETERIOGENIC FILAMENTOUS FUNGI BY RNA-FISH

Filamentous fungi are a threat to the conservation of Cultural Heritage. Thus, detection and identification of viable filamentous fungi are crucial for applying adequate Safeguard measures. RNA-FISH protocols have been previously applied with this aim in Cultural Heritage samples. However, only hyphae detection was reported in the literature, even if spores and conidia are not only a potential risk to Cultural Heritage but can also be harmful for the health of visitors, curators and restorers. Thus, the aim of this work was to evaluate various permeabilizing strategies for their application in the detection of spores/conidia and hyphae of artworks’ biodeteriogenic filamentous fungi by RNA-FISH. Besides of this, the influence of cell aging on the success of the technique and on the development of fungal autofluorescence (that could hamper the RNA-FISH signal detection) were also investigated. Five common biodeteriogenic filamentous fungi species isolated from biodegradated artworks were used as biological model: Aspergillus niger, Cladosporium sp, Fusarium sp, Penicillium sp. and Exophialia sp. Fungal autofluorescence was only detected in cells harvested from Fusarium sp, and Exophialia sp. old cultures, being aging-dependent. However, it was weak enough to allow autofluorescence/RNA-FISH signals distinction. Thus, autofluorescence was not a limitation for the application of RNA-FISH for detection of the taxa investigated. All the permeabilization strategies tested allowed to detect fungal cells from young cultures by RNA-FISH. However, only the combination of paraformaldehyde with Triton X-100 allowed the detection of conidia/spores and hyphae of old filamentous fungi. All the permeabilization strategies failed in the Aspergillus niger conidia/spores staining, which are known to be particularly difficult to permeabilize. But, even in spite of this, the application of this permeabilization method increased the analytical potential of RNA FISH in Cultural Heritage biodeterioration. Whereas much work is required to validate this RNA-FISH approach for its application in real samples from Cultural Heritage it could represent an important advance for the detection, not only of hyphae but also of spores and conidia of various filamentous fungi taxa by RNA-FISH.

The morphological characterization of the dry seeds and reserve mobilization during germination in Morinda citrifolia L.

2016

Robustness of germination analysis methods for Copaifera langsdorffii Desf. (Fabaceae) seeds.

2016

In vitro seed germination and multiplication of Calophyllum brasiliense.

Calophyllum brasiliense é uma espécie arbórea com sistema de propagação natural limitada. A germinação in vitro pode ser uma alternativa para obtenção de plântulas de qualidade. Sementes foram mantidas em água antes da desinfestação e comparadas com sementes controle (não imersas), sem diferença entre os tratamentos. HgCl2 usado durante a desinfestação reduziu a contaminação das culturas. A contaminação fúngica foi reduzida com fungicida adicionado ao meio (23 para 6,4%), mas a porcentagem de bactérias foi aumentada (24 para 36%). Em outro experimento, as sementes foram imersas em plant preservative mixture (PPM?) antes da desinfestação. Combinando a imersão por 48 h e 2 mL L-1 no meio de cultura, a contaminação foi de 6%. A imersão das sementes em GA3 antes da desinfestação reduziu a formação de raízes conforme a concentração foi aumentada. A germinação e o IVG foram reduzidos, respectivamente, de 72% e 0,129 (24 h) para 60% e 0,092 (48 h), de acordo com o tempo de exposição a GA3. Após 90 dias em meio de multiplicação contendo benzilaminopurina, o número médio de brotações por segmento nodal foi 3,4. A germinação in vitro de C. brasiliense é viável em meio WPM sem sacarose, com até 93,3% de sobrevivência.

The infection of soybean leaves by Phakopsora pachyrhizi during conditions of discontinuous wetness.

The ability of Phakopsora pachyrhizi to cause infection under conditions of discontinuous wetness was investigated. In in vitro experiments, droplets of a uredospore suspension were deposited onto the surface of polystyrene. After an initial wetting period of either 1, 2 or 4 h, the drops were dried for different time intervals and then the wetness was restored for 11, 10 or 8 h. Germination and appressorium formation were evaluated. In in vivo experiments, soybean plants were inoculated with a uredospore suspension. Leaf wetness was interrupted for 1, 3 or 6 h after initial wetting periods of 1, 2 or 4 h. Then, the wetting was re-established for 11, 10 or 8 h, respectively. Rust severity was evaluated 14 days after inoculation. The germination of the spores and the formation of the appressoria on the soybean leaves after different periods of wetness were also quantified in vivo by scanning electron microscopy. P. pachyrhizi showed a high infective capacity during short periods of time. An interruption of wetness after 1 h caused average reductions in germination from 56 to 75% and in appressorium formation from 84 to 96%. Rust severity was lower in all of the in vivo treatments with discontinuous wetness when compared to the control plants. Rust severity was zero when the interruption of wetness occurred 4 h after the initial wetting. Wetting interruptions after 1 and 2 h reduced the average rust severity by 83 and 77%, respectively. The germination of the uredospores on the soybean leaves occurred after 2 h of wetness, with a maximum germination appearing after 4 h of wetness. Wetness interruption affected mainly the spores that had initiated the germination.

Synchronizing the in vitro germination of Psidium guineense Sw. seeds by means of osmotic priming.

The Brazilian guava (Psidium guineense Swartz) is seed-propagated and, being native to the Caatinga biome, may frequently have uneven germination.Thus, we aimed to evaluate the synchronization of the in vitro seed germination of three accessions of the Brazilian guava, using water, polyethyleneglycol (PEG 6000), and potassium nitrate (KNO3) at different potentials and times of osmotic priming. Seeds from three accessions of the Brazilian guava (Y85, Y93,and Y97) from the UNEB/BA Germplasm Active Bank were subjected to the following pretreatments: -0.6, -1.0, -1.4, and -1,8 MPa PEG 6000; 10 and 20% KNO3 for 24h; 10 and 20% KNO3 for 48h; water for 24 and 48h; and non-primed seeds as the control. The experimental design was therefore a 10x3+1 factorial scheme. We assessed the germination percentage (G), mean germination time (MGT), germination speed (GS), and germination speed index (GSI). Data was subjected to analysis of variance followed by a means test (Duncan at 5% probability) and regression. There was interaction between the priming treatments and accessions for all evaluated features, except G. PEG 6000 decreased the MGT (from 6 to 8 days) and increased GS and GSI of seeds from all three accessions at potentials -1.0 to -1.5 MPa.Water-priming had a positive effect on MGT, GS, and GSI of accession Y85 seeds. KNO3 negatively affected germination of seeds from all three accessions. Thereby, we could synchronize seed germination of accessions Y85 and Y97 with PEG 6000.

Fungal spore fragmentation as a function of airflow rates and fungal generation methods

The aim of this study was to characterise and quantify the fungal fragment propagules derived and released from several fungal species (Penicillium, Aspergillus niger and Cladosporium cladosporioides) using different generation methods and different air velocities over the colonies. Real time fungal spore fragmentation was investigated using an Ultraviolet Aerodynamic Particle Sizer (UVASP) and a Scanning Mobility Particle Sizer (SMPS). The study showed that there were significant differences (p < 0.01) in the fragmentation percentage between different air velocities for the three generation methods, namely the direct, the fan and the fungal spore source strength tester (FSSST) methods. The percentage of fragmentation also proved to be dependant on fungal species. The study found that there was no fragmentation for any of the fungal species at an air velocity ≤ 0.4 m/s for any method of generation. Fluorescent signals, as well as mathematical determination also showed that the fungal fragments were derived from spores. Correlation analysis showed that the number of released fragments measured by the UVAPS under controlled conditions can be predicted on the basis of the number of spores, for Penicillium and Aspergillus niger, but not for Cladosporium cladosporioides. The fluorescence percentage of fragment samples was found to be significantly different to that of non-fragment samples (p < 0.0001) and the fragment sample fluorescence was always less than that of the non-fragment samples. Size distribution and concentration of fungal fragment particles were investigated qualitatively and quantitatively, by both UVAPS and SMPS, and it was found that the UVAPS was more sensitive than the SMPS for measuring small sample concentrations, and the results obtained from the UVAPS and SMAS were not identical for the same samples.

Somatic embryogenesis, organogenesis and plant regeneration in taro (Colocasia esculenta var. esculenta)

Callus was initiated in three different ‘‘esculenta’’ taro cultivars by culturing corm slices in the dark on half-strength MS medium supplemented with 2.0 mg/l 2,4- dichlorophenoxyacetic acid (2,4-D) for 20 days followed by subculture of all corm slices to half-strength MS medium containing 1.0 mg/l thidiazuron (TDZ). Depending on the cultivar, 20–30% of corm slices produced compact, yellow, nodular callus on media containing TDZ. Histological studies revealed the presence of typical embryogenic cells which were small, isodiametric with dense cytoplasms. Somatic embryos formed when callus was transferred to hormone-free medium and *72% of the embryos germinated into plantlets on this medium. Simultaneous formation of roots and shoots during germination, and the presence of shoot and root poles revealed by histology, confirmed that these structures were true somatic embryos. Plants derived from somatic embryos appeared phenotypically normal following 2 months growth in a glasshouse. This method is a significant advance on those previously reported for the esculenta cultivars of taro due to its efficiency and reproducibility.