Isolated electrical microgrids employing renewable energy resources:analysis of the electrification of remote communities in Peru.

This project points out a brief overview of several concepts, as Renewable Energy Resources, Distributed Energy Resources, Distributed Generation, and describes the general architecture of an electrical microgrid, isolated or connected to the Medium Voltage Network. Moreover, the project focuses on a project carried out by GRECDH Department in collaboration with CITCEA Department, both belonging to Universitat Politécnica de Catalunya: it concerns isolated microgrids employing renewable energy resources in two communities in northern Peru. Several solutions found using optimization software regarding different generation systems (wind and photovoltaic) and different energy demand scenarios are commented and analyzed from an electrical point of view. Furthermore, there are some proposals to improve microgrid performances, in particular to increase voltage values for each load connected to the microgrid. The extra costs required by the proposed solutions are calculated and their effect on the total microgrid cost are taken into account; finally there are some considerations about the impact the project has on population and on people's daily life.

Partial discharge in power distribution electrical systems: pulse propagation models and detection optimization

Investigation on impulsive signals, originated from Partial Discharge (PD) phenomena, represents an effective tool for preventing electric failures in High Voltage (HV) and Medium Voltage (MV) systems. The determination of both sensors and instruments bandwidths is the key to achieve meaningful measurements, that is to say, obtaining the maximum Signal-To-Noise Ratio (SNR). The optimum bandwidth depends on the characteristics of the system under test, which can be often represented as a transmission line characterized by signal attenuation and dispersion phenomena. It is therefore necessary to develop both models and techniques which can characterize accurately the PD propagation mechanisms in each system and work out the frequency characteristics of the PD pulses at detection point, in order to design proper sensors able to carry out PD measurement on-line with maximum SNR. Analytical models will be devised in order to predict PD propagation in MV apparatuses. Furthermore, simulation tools will be used where complex geometries make analytical models to be unfeasible. In particular, PD propagation in MV cables, transformers and switchgears will be investigated, taking into account both irradiated and conducted signals associated to PD events, in order to design proper sensors.

Novel techniques for the remote sensing of photosynthetic processes

Remote sensing (RS) techniques have evolved into an important instrument to investigate forest function. New methods based on the remote detection of leaf biochemistry and photosynthesis are being developed and applied in pilot studies from airborne and satellite platforms (PRI, solar-induced fluorescence; N and chlorophyll content). Non-destructive monitoring methods, a direct application of RS studies, are also proving increasingly attractive for the determination of stress conditions or nutrient deficiencies not only in research but also in agronomy, horticulture and urban forestry (proximal RS). In this work I will focus on some novel techniques recently developed for the estimation of photochemistry and photosynthetic rates based (i) on the proximal measurement of steady-state chlorophyll fluorescence yield, or (ii) the remote sensing of changes in hyperspectral leaf reflectance, associated to xanthophyll de-epoxydation and energy partitioning, which is closely coupled to leaf photochemistry and photosynthesis. I will also present and describe a mathematical model of leaf steady-state fluorescence and photosynthesis recently developed in our group. Two different species were used in the experiments: Arbutus unedo, a schlerophyllous Mediterranean species, and Populus euroamericana, a broad leaf deciduous tree widely used in plantation forestry. Results show that ambient fluorescence could provide a useful tool for testing photosynthetic processes from a distance. These results confirm also the photosynthetic reflectance index (PRI) as an efficient remote sensing reflectance index estimating short-term changes in photochemical efficiency as well as long-term changes in leaf biochemistry. The study also demonstrated that RS techniques could provide a fast and reliable method to estimate photosynthetic pigment content and total nitrogen, beside assessing the state of photochemical process in our plants’ leaves in the field. This could have important practical applications for the management of plant cultivation systems, for the estimation of the nutrient requirements of our plants for optimal growth.

Numerical analysis of Dielectric Barrier Discharge

A numerical investigation of dielectric barrier discharge aimed to simulate the electro hydro dynamic interaction is presented. A discharge drift diffusive model according to the Townsend avalanche is described and used to duplicate the plasma kinetics of a DBD actuator. The discharge characteristics dependence upon dielectric material and applied voltage are simulated and the EHD force field according to a simplified approach is presented and discussed. The coupling of DBD results with a fluid dynamic code is also shown. Finally, a new non invasive diagnostic technique for EHD interaction based on Schlieren imaging is computationally validated.

Applications of remote sensing and geographic information systems in geomorphological studies: Safaga - El Quseir area, Red Sea coast, Egypt as an example

In den letzten drei Jahrzehnten sind Fernerkundung und GIS in den Geowissenschaften zunehmend wichtiger geworden, um die konventionellen Methoden von Datensammlung und zur Herstellung von Landkarten zu verbessern. Die vorliegende Arbeit befasst sich mit der Anwendung von Fernerkundung und geographischen Informationssystemen (GIS) für geomorphologische Untersuchungen. Durch die Kombination beider Techniken ist es vor allem möglich geworden, geomorphologische Formen im Überblick und dennoch detailliert zu erfassen. Als Grundlagen werden in dieser Arbeit topographische und geologische Karten, Satellitenbilder und Klimadaten benutzt. Die Arbeit besteht aus 6 Kapiteln. Das erste Kapitel gibt einen allgemeinen Überblick über den Untersuchungsraum. Dieser umfasst folgende morphologische Einheiten, klimatischen Verhältnisse, insbesondere die Ariditätsindizes der Küsten- und Gebirgslandschaft sowie das Siedlungsmuster beschrieben. Kapitel 2 befasst sich mit der regionalen Geologie und Stratigraphie des Untersuchungsraumes. Es wird versucht, die Hauptformationen mit Hilfe von ETM-Satellitenbildern zu identifizieren. Angewandt werden hierzu folgende Methoden: Colour Band Composite, Image Rationing und die sog. überwachte Klassifikation. Kapitel 3 enthält eine Beschreibung der strukturell bedingten Oberflächenformen, um die Wechselwirkung zwischen Tektonik und geomorphologischen Prozessen aufzuklären. Es geht es um die vielfältigen Methoden, zum Beispiel das sog. Image Processing, um die im Gebirgskörper vorhandenen Lineamente einwandfrei zu deuten. Spezielle Filtermethoden werden angewandt, um die wichtigsten Lineamente zu kartieren. Kapitel 4 stellt den Versuch dar, mit Hilfe von aufbereiteten SRTM-Satellitenbildern eine automatisierte Erfassung des Gewässernetzes. Es wird ausführlich diskutiert, inwieweit bei diesen Arbeitsschritten die Qualität kleinmaßstäbiger SRTM-Satellitenbilder mit großmaßstäbigen topographischen Karten vergleichbar ist. Weiterhin werden hydrologische Parameter über eine qualitative und quantitative Analyse des Abflussregimes einzelner Wadis erfasst. Der Ursprung von Entwässerungssystemen wird auf der Basis geomorphologischer und geologischer Befunde interpretiert. Kapitel 5 befasst sich mit der Abschätzung der Gefahr episodischer Wadifluten. Die Wahrscheinlichkeit ihres jährlichen Auftretens bzw. des Auftretens starker Fluten im Abstand mehrerer Jahre wird in einer historischen Betrachtung bis 1921 zurückverfolgt. Die Bedeutung von Regentiefs, die sich über dem Roten Meer entwickeln, und die für eine Abflussbildung in Frage kommen, wird mit Hilfe der IDW-Methode (Inverse Distance Weighted) untersucht. Betrachtet werden außerdem weitere, regenbringende Wetterlagen mit Hilfe von Meteosat Infrarotbildern. Genauer betrachtet wird die Periode 1990-1997, in der kräftige, Wadifluten auslösende Regenfälle auftraten. Flutereignisse und Fluthöhe werden anhand von hydrographischen Daten (Pegelmessungen) ermittelt. Auch die Landnutzung und Siedlungsstruktur im Einzugsgebiet eines Wadis wird berücksichtigt. In Kapitel 6 geht es um die unterschiedlichen Küstenformen auf der Westseite des Roten Meeres zum Beispiel die Erosionsformen, Aufbauformen, untergetauchte Formen. Im abschließenden Teil geht es um die Stratigraphie und zeitliche Zuordnung von submarinen Terrassen auf Korallenriffen sowie den Vergleich mit anderen solcher Terrassen an der ägyptischen Rotmeerküste westlich und östlich der Sinai-Halbinsel.

Utilizzo delle bande dell’Infrarosso Termico in tecniche di remote sensing per applicazioni in ambito urbano

Il presente studio si concentra sulle diverse applicazioni del telerilevamento termico in ambito urbano. Vengono inizialmente descritti la radiazione infrarossa e le sue interazioni con l’atmosfera terrestre, le leggi principali che regolano lo scambio di calore per irraggiamento, le caratteristiche dei sensori e le diverse applicazioni di termografia. Successivamente sono trattati nel dettaglio gli aspetti caratteristici della termografia da piattaforma satellitare, finalizzata principalmente alla valutazione del fenomeno dell'Urban Heat Island; vengono descritti i sensori disponibili, le metodologie di correzione per gli effetti atmosferici, per la stima dell'emissività delle superfici e per il calcolo della temperatura superficiale dei pixels. Viene quindi illustrata la sperimentazione effettuata sull'area di Bologna mediante immagini multispettrali ASTER: i risultati mostrano come sull'area urbana sia riscontrabile la presenza dell'Isola di Calore Urbano, anche se la sua quantificazione risulta complessa. Si procede quindi alla descrizione di potenzialità e limiti della termografia aerea, dei suoi diversi utilizzi, delle modalità operative di rilievo e degli algoritmi utilizzati per il calcolo della temperatura superficiale delle coperture edilizie. Tramite l’analisi di alcune esperienze precedenti vengono trattati l’influenza dell’atmosfera, la modellazione dei suoi effetti sulla radianza rilevata, i diversi metodi per la stima dell’emissività. Viene quindi introdotto il progetto europeo Energycity, finalizzato alla creazione di un sistema GeoWeb di supporto spaziale alle decisioni per la riduzione di consumi energetici e produzione di gas serra su sette città dell'Europa Centrale. Vengono illustrate le modalità di rilievo e le attività di processing dei datasets digitali per la creazione di mappe di temperatura superficiale da implementare nel sistema SDSS. Viene infine descritta la sperimentazione effettuata sulle immagini termiche acquisite nel febbraio 2010 sulla città di Treviso, trasformate in un mosaico georiferito di temperatura radiometrica tramite correzioni geometriche e radiometriche; a seguito della correzione per l’emissività quest’ultimo verrà trasformato in un mosaico di temperatura superficiale.

Flash floods and their effects on the development in El-Qaá plain area in South Sinai, Egypt

The arid regions are dominated to a much larger degree than humid regions by major catastrophic events. Although most of Egypt lies within the great hot desert belt; it experiences especially in the north some torrential rainfall, which causes flash floods all over Sinai Peninsula. Flash floods in hot deserts are characterized by high velocity and low duration with a sharp discharge peak. Large sediment loads may be carried by floods threatening fields and settlements in the wadis and even people who are living there. The extreme spottiness of rare heavy rainfall, well known to desert people everywhere, precludes any efficient forecasting. Thus, although the limitation of data still reflects pre-satellite methods, chances of developing a warning system for floods in the desert seem remote. The relatively short flood-to-peak interval, a characteristic of desert floods, presents an additional impediment to the efficient use of warning systems. The present thesis contains introduction and five chapters, chapter one points out the physical settings of the study area. There are the geological settings such as outcrop lithology of the study area and the deposits. The alluvial deposits of Wadi Moreikh had been analyzed using OSL dating to know deposits and palaeoclimatic conditions. The chapter points out as well the stratigraphy and the structure geology containing main faults and folds. In addition, it manifests the pesent climate conditions such as temperature, humidity, wind and evaporation. Besides, it presents type of soils and natural vegetation cover of the study area using unsupervised classification for ETM+ images. Chapter two points out the morphometric analysis of the main basins and their drainage network in the study area. It is divided into three parts: The first part manifests the morphometric analysis of the drainage networks which had been extracted from two main sources, topographic maps and DEM images. Basins and drainage networks are considered as major influencing factors on the flash floods; Most of elements were studied which affect the network such as stream order, bifurcation ratio, stream lengths, stream frequency, drainage density, and drainage patterns. The second part of this chapter shows the morphometric analysis of basins such as area, dimensions, shape and surface. Whereas, the third part points the morphometric analysis of alluvial fans which form most of El-Qaá plain. Chapter three manifests the surface runoff through rainfall and losses analysis. The main subject in this chapter is rainfall which has been studied in detail; it is the main reason for runoff. Therefore, all rainfall characteristics are regarded here such as rainfall types, distribution, rainfall intensity, duration, frequency, and the relationship between rainfall and runoff. While the second part of this chapter concerns with water losses estimation by evaporation and infiltration which are together the main losses with direct effect on the high of runoff. Finally, chapter three points out the factors influencing desert runoff and runoff generation mechanism. Chapter four is concerned with assessment of flood hazard, it is important to estimate runoff and tocreate a map of affected areas. Therefore, the chapter consists of four main parts; first part manifests the runoff estimation, the different methods to estimate runoff and its variables such as runoff coefficient lag time, time of concentration, runoff volume, and frequency analysis of flash flood. While the second part points out the extreme event analysis. The third part shows the map of affected areas for every basin and the flash floods degrees. In this point, it has been depending on the DEM to extract the drainage networks and to determine the main streams which are normally more dangerous than others. Finally, part four presets the risk zone map of total study area which is of high inerest for planning activities. Chapter five as the last chapter concerns with flash flood Hazard mitigation. It consists of three main parts. First flood prediction and the method which can be used to predict and forecast the flood. The second part aims to determine the best methods which can be helpful to mitigate flood hazard in the arid zone and especially the study area. Whereas, the third part points out the development perspective for the study area indicating the suitable places in El-Qaá plain for using in economic activities.

The impact of ice crystals on radiative forcing and remote sensing of arctic boundary-layer mixed-phase clouds

This PhD thesis is embedded into the Arctic Study of Tropospheric Aerosol, Clouds and Radiation (ASTAR) and investigates the radiative transfer through Arctic boundary-layer mixed-phase (ABM) clouds. For this purpose airborne spectral solar radiation measurements and simulations of the solar and thermal infrared radiative transfer have been performed. This work reports on measurements with the Spectral Modular Airborne Radiation measurement sysTem (SMART-Albedometer) conducted in the framework of ASTAR in April 2007 close to Svalbard. For ASTAR the SMART-Albedometer was extended to measure spectral radiance. The development and calibration of the radiance measurements are described in this work. In combination with in situ measurements of cloud particle properties provided by the Laboratoire de M¶et¶eorologie Physique (LaMP) and simultaneous airborne lidar measurements by the Alfred Wegener Institute for Polar and Marine Research (AWI) ABM clouds were sampled. The SMART-Albedometer measurements were used to retrieve the cloud thermodynamic phase by three different approaches. A comparison of these results with the in situ and lidar measurements is presented in two case studies. Beside the dominating mixed-phase clouds pure ice clouds were found in cloud gaps and at the edge of a large cloud field. Furthermore the vertical distribution of ice crystals within ABM clouds was investigated. It was found that ice crystals at cloud top are necessary to describe the observed SMART-Albedometer measurements. The impact of ice crystals on the radiative forcing of ABM clouds is in vestigated by extensive radiative transfer simulations. The solar and net radiative forcing was found to depend on the ice crystal size, shape and the mixing ratio of ice crystals and liquid water droplets.

New techniques for the remote sensing of foliar nitrogen concentration in forest ecosystems.

During my Doctoral study I researched about the remote detection of canopy N concentration in forest stands, its potentials and problems, under many overlapping perspectives. The study consisted of three parts. In S. Rossore 2000 dataset analysis, I tested regressions between N concentration and NIR reflectances derived from different sources (field samples, airborne and satellite sensors). The analysis was further expanded using a larger dataset acquired in year 2009 as part of a new campaign funded by the ESA. In both cases, a good correlation was observed between Landsat NIR, using both TM (2009) and ETM+ (2000) imagery, and N concentration measured by a CHN elemental analyzer. Concerning airborne sensors I did not obtain the same good results, mainly because of the large FOV of the two instruments, and to the anisotropy of vegetation reflectance. We also tested the relation between ground based ASD measures and nitrogen concentration, obtaining really good results. Thus, I decided to expand my study to the regional level, focusing only on field and satellite measures. I analyzed a large dataset for the whole of Catalonia, Spain; MODIS imagery was used, in consideration of its spectral characteristics and despite its rather poor spatial resolution. Also in this case a regression between nitrogen concentration and reflectances was found, but not so good as in previous experiences. Moreover, vegetation type was found to play an important role in the observed relationship. We concluded that MODIS is not the most suitable satellite sensor in realities like Italy and Catalonia, which present a patchy and inhomogeneous vegetation cover; so it could be utilized for the parameterization of eco-physiological and biogeochemical models, but not for really local nitrogen estimate. Thus multispectral sensors similar to Landsat Thematic Mapper, with better spatial resolution, could be the most appropriate sensors to estimate N concentration.

Oxidation photochemistry in the remote marine boundary layer

Die bedeutendste Folge der Luftverschmutzung ist eine erhöhte Konzentration an Ozon (O3) in der Troposphäre innerhalb der letzten 150 Jahre. Ozon ist ein photochemisches Oxidationsmittel und ein Treibhausgas, das als wichtigste Vorstufe des Hydroxyradikals OH die Oxidationskraft der Atmosphäre stark beeinflusst. Um die Oxidationskraft der Atmosphäre und ihren Einfluss auf das Klima verstehen zu können, ist es von großer Bedeutung ein detailliertes Wissen über die Photochemie des Ozons und seiner Vorläufer, den Stickoxiden (NOx), in der Troposphäre zu besitzen. Dies erfordert das Verstehen der Bildungs- und Abbaumechanismen von Ozon und seiner Vorläufer. Als eine für den chemischen Ozonabbau wichtige Region kann die vom Menschen weitgehend unberührte marine Grenzschicht (Marine boundary layer (MBL)) angesehen werden. Bisher wurden für diese Region jedoch kaum Spurengasmessungen durchgeführt, und so sind die dort ablaufenden photochemischen Prozesse wenig untersucht. Da etwa 70 % der Erdoberfläche mit Ozeanen bedeckt sind, können die in der marinen Granzschicht ablaufenden Prozesse als signifikant für die gesamte Atmosphäre angesehen werden. Dies macht eine genaue Untersuchung dieser Region interessant. Um die photochemische Produktion und den Abbau von Ozon abschätzen zu können und den Einfluss antrophogener Emissionen auf troposphärisches Ozon zu quantifizieren, sind aktuelle Messergebnisse von NOx im pptv-Bereich für diese Region erforderlich. Die notwendigen Messungen von NO, NO2, O3, JNO2, J(O1D), HO2, OH, ROx sowie einiger meteorologischer Parameter wurden während der Fahrt des französischen Forschungsschiffes Marion-Dufresne auf dem südlichen Atlantik (28°S-57°S, 46°W-34°E) im März 2007 durchgeführt. Dabei sind für NO und NO2 die bisher niedrigsten gemessenen Werte zu verzeichnen. Die während der Messcampagne gewonnen Daten wurden hinsichtlich Ihrer Übereinstimmung mit den Bedingungen des photochemischen stationären Gleichgewichts (photochemical steady state (PSS)) überprüft. Dabei konnte eine Abweichung vom PSS festgestellt werden, welche unter Bedingungen niedriger NOx-Konzentrationen (5 bis 25pptv) einen unerwarteten Trend im Leighton-Verhältnis bewirkt, der abhängig vom NOx Mischungsverhältnis und der JNO2 Intensität ist. Signifikante Abweichungen vom Verhältnis liegen bei einer Zunahme der JNO2 Intensität vor. Diese Ergebnisse zeigen, dass die Abweichung vom PSS nicht beim Minimum der NOx-Konzentrationen und der JNO2 Werte liegt, so wie es in bisherigen theoretischen Studien dargelegt wurde und können als Hinweis auf weitere photochemische Prozesse bei höheren JNO2-Werten in einem System mit niedrigem NOx verstanden werden. Das wichtigste Ergebnis dieser Untersuchung, ist die Verifizierung des Leighton-Verhältnisses, das zur Charakterisierung des PSS dient, bei sehr geringen NOx-Konzentrationen in der MBL. Die bei dieser Doktorarbeit gewonnenen Erkenntnisse beweisen, dass unter den Bedingungen der marinen Granzschicht rein photochemischer Abbau von Ozon stattfindet und als Hauptursache hierfür während des Tages die Photolyse gilt. Mit Hilfe der gemessenen Parameter wurde der kritische NO-Level auf Werte zwischen 5 und 9 pptv abgeschätzt, wobei diese Werte im Vergleich zu bisherigen Studien vergleichsweise niedrig sind. Möglicherweise bedeutet dies, dass das Ozon Produktion/ Abbau-Potential des südlichen Atlantiks deutlich stärker auf die Verfügbarkeit von NO reagiert, als es in anderen Regionen der Fall ist. Im Rahmen der Doktorarbeit wurde desweiteren ein direkter Vergleich der gemessenen Spezies mit dem Modelergebnis eines 3-dimensionalen Zirkulationsmodel zur Simulation atmosphären chemischer Prozesse (EMAC) entlang der exakten Schiffsstrecke durchgeführt. Um die Übereinstimmung der Messergebnisse mit dem bisherigen Verständnis der atmosphärischen Radikalchemie zu überprüfen, wurde ein Gleichgewichtspunktmodel entwickelt, das die während der Überfahrt erhaltenen Daten für Berechungen verwendet. Ein Vergleich zwischen der gemessenen und der modellierten ROx Konzentrationen in einer Umgebung mit niedrigem NOx zeigt, dass die herkömmliche Theorie zur Reproduktion der Beobachtungen unzureichend ist. Die möglichen Gründe hierfür und die Folgen werden in dieser Doktorarbeit diskutiert.

Partial Discharge Phenomena in Converter and Traction Transformers: Identification and Reliability

After the development of power electronics converters, the number of transformers subjected to non-sinusoidal stresses (including DC) has increased in applications such as HVDC links and traction (electric train power cars). The effects of non-sinusoidal voltages on transformer insulation have been investigated by many researchers, but still now, there are some issues that must be understood. Some of those issues are tackled in this Thesis, studying PD phenomena behavior in Kraft paper, pressboard and mineral oil at different voltage conditions like AC, DC, AC+DC, notched AC and square waveforms. From the point of view of converter transformers, it was found that the combined effect of AC and DC voltages produces higher stresses in the pressboard that those that are present under pure DC voltages. The electrical conductivity of the dielectric systems in DC and AC+DC conditions has demonstrated to be a critical parameter, so, its measurement and analysis was also taken into account during all the experiments. Regarding notched voltages, the RMS reduction caused by notches (depending on firing and overlap angles) seems to increase the PDIV. However, the experimental results show that once PD activity has incepted, the notches increase PD repetition rate and magnitude, producing a higher degradation rate of paper. On the other hand, the reduction of mineral oil stocks, their relatively low flash point as well as environmental issues, are factors that are pushing towards the use of esters as transformer insulating fluids. This PhD Thesis also covers the study of two different esters with the scope to validate their use in traction transformers. Mineral oil was used as benchmark. The complete set of dielectric tests performed in the three fluids, show that esters behave better than mineral oil in practically all the investigated conditions, so, their application in traction transformers is possible and encouraged.

Fast and accurate numerical solutions in some problems of particle and radiation transport: synthetic acceleration for the method of short characteristics, Doppler-broadened scattering kernel, remote sensing of the cryosphere

The aim of this work is to present various aspects of numerical simulation of particle and radiation transport for industrial and environmental protection applications, to enable the analysis of complex physical processes in a fast, reliable, and efficient way. In the first part we deal with speed-up of numerical simulation of neutron transport for nuclear reactor core analysis. The convergence properties of the source iteration scheme of the Method of Characteristics applied to be heterogeneous structured geometries has been enhanced by means of Boundary Projection Acceleration, enabling the study of 2D and 3D geometries with transport theory without spatial homogenization. The computational performances have been verified with the C5G7 2D and 3D benchmarks, showing a sensible reduction of iterations and CPU time. The second part is devoted to the study of temperature-dependent elastic scattering of neutrons for heavy isotopes near to the thermal zone. A numerical computation of the Doppler convolution of the elastic scattering kernel based on the gas model is presented, for a general energy dependent cross section and scattering law in the center of mass system. The range of integration has been optimized employing a numerical cutoff, allowing a faster numerical evaluation of the convolution integral. Legendre moments of the transfer kernel are subsequently obtained by direct quadrature and a numerical analysis of the convergence is presented. In the third part we focus our attention to remote sensing applications of radiative transfer employed to investigate the Earth's cryosphere. The photon transport equation is applied to simulate reflectivity of glaciers varying the age of the layer of snow or ice, its thickness, the presence or not other underlying layers, the degree of dust included in the snow, creating a framework able to decipher spectral signals collected by orbiting detectors.

The use of satellite remote sensing for flood risk management

Over the last decades the impact of natural disasters to the global environment is becoming more and more severe. The number of disasters has dramatically increased, as well as the cost to the global economy and the number of people affected. Among the natural disaster, flood catastrophes are considered to be the most costly, devastating, broad extent and frequent, because of the tremendous fatalities, injuries, property damage, economic and social disruption they cause to the humankind. In the last thirty years, the World has suffered from severe flooding and the huge impact of floods has caused hundreds of thousands of deaths, destruction of infrastructures, disruption of economic activity and the loss of property for worth billions of dollars. In this context, satellite remote sensing, along with Geographic Information Systems (GIS), has become a key tool in flood risk management analysis. Remote sensing for supporting various aspects of flood risk management was investigated in the present thesis. In particular, the research focused on the use of satellite images for flood mapping and monitoring, damage assessment and risk assessment. The contribution of satellite remote sensing for the delineation of flood prone zones, the identification of damaged areas and the development of hazard maps was explored referring to selected cases of study.

Applications of GIS and remote sensing techniques for studying the housing patterns in Cairo Governorate

The main objective of this study is to reveal the housing patterns in Cairo as one of the most rapidly urbanizing city in the developing world. The study outlines the evolution of the housing problem and its influencing factors in Egypt generally and in Cairo specifically. The study takes into account the political transition from the national state economy to the open door policy, the neo-liberal period and finally to the housing situation after the January 2011 Revolution. The resulting housing patterns in Cairo Governorate were identified as (1) squatter settlements, (2) semi-informal settlements, (3) deteriorated inner pockets, and (4) formal settlements. rnThe study concluded that the housing patterns in Cairo are reflecting a multifaceted problem resulting in: (1) the imbalance between the high demand for affordable housing units for low-income families and the oversupply of upper-income housing, (2) the vast expansion of informal areas both on agricultural and desert lands, (3) the deterioration of the old parts of Cairo without upgrading or appropriate replacement of the housing structure, and (4) the high vacancy rate of newly constructed apartmentsrnThe evolution and development of the current housing problem were attributed to a number of factors. These factors are demographic factors represented in the rapid growth of the population associated with urbanization under the dictates of poverty, and the progressive increase of the prices of both buildable land and building materials. The study underlined that the current pattern of population density in Cairo Governorate is a direct result of the current housing problems. Around the depopulation core of the city, a ring of relatively stable areas in terms of population density has developed. Population densification, at the expense of the depopulation core, is characterizing the peripheries of the city. The population density in relation to the built-up area was examined using Landsat-7 ETM+ image (176/039). The image was acquired on 24 August 2006 and considered as an ideal source for land cover classification in Cairo since it is compatible with the population census 2006.rnConsidering that the socio-economic setting is a driving force of change of housing demand and that it is an outcome of the accumulated housing problems, the socio-economic deprivations of the inhabitants of Cairo Governorate are analyzed. Small administrative units in Cairo are categorized into four classes based on the Socio-Economic Opportunity Index (SEOI). This index is developed by using multiple domains focusing on the economic, educational and health situation of the residential population. The results show four levels of deprivation which are consistent with the existing housing patterns. Informal areas on state owned land are included in the first category, namely, the “severely deprived” level. Ex-formal areas or deteriorated inner pockets are characterized as “deprived” urban quarters. Semi-informal areas on agricultural land concentrate in the third category of “medium deprived” settlements. Formal or planned areas are included mostly in the fourth category of the “less deprived” parts of Cairo Governorate. rnFor a better understanding of the differences and similarities among the various housing patterns, four areas based on the smallest administrative units of shiakhat were selected for a detailed study. These areas are: (1) El-Ma’desa is representing a severely deprived squatter settlement, (2) Ain el-Sira is an example for an ex-formal deprived area, (3) El-Marg el-Qibliya was selected as a typical semi-informal and medium deprived settlement, and (4) El-Nozha is representing a formal and less deprived area.rnThe analysis at shiakhat level reveals how the socio-economic characteristics and the unregulated urban growth are greatly reflected in the morphological characteristics of the housing patterns in terms of street network and types of residential buildings as well as types of housing tenure. It is also reflected in the functional characteristics in terms of land use mix and its degree of compatibility. It is concluded that the provision and accessibility to public services represents a performance measure of the dysfunctional structure dominating squatter and semi-informal settlements on one hand and ample public services and accessibility in formal areas on the other hand.rn