Image Analysis for the Characterization of Materials for Highway Construction : Phase I, Progress Report, HR-346, 1992

The major objective of this project is to evaluate image analysis for characterizing air voids in Portland cement contract (PCC) and asphalt concrete (AC) and aggregate gradation in asphalt concrete. Phase 1 of this project has concentrated on evaluation and refinement of sample preparation techniques, evaluation of methods and instruments for conducting image analysis, and finally, analysis and comparison of a select portion of samples. Preliminary results suggest a strong correlation between the results obtained from the linear traverse method and image analysis methods for determining percent air voids in concrete. Preliminary work with asphalt samples has shown that damage caused by a high vacuum of the conventional scanning electron microscope (SEM) may too disruptive. Alternative solutions have been explored, including confocal microscopy and low vacuum electron microscopy. Additionally, a conventional high vacuum SEM operating at a marginal operating vacuum may suffice.

Granular Base Materials for Flexible Pavements, HR-131, 1970

The coefficients of relative strength (CORS) of base courses for use in the American association state highway officials (AASHO) interim guide for the design of flexible pavements are determined here. Based on (1) volumetric strain--axial strain relationships at minimum volume, and (2) effective stress ratio-cohesion relationships at maximum effective stress ratio, CORS were determined from the results of laboratory triaxial tests on both asphalt-treated and untreated aggregate base course materials. The researchers conclude that volumetric strain-axial strain at minimum volume appear to be appropriate parameters for determining CORS.

Geologic and Engineering Properties of Pleistocene Materials in Iowa, Iowa Highway Research Board Bulletin No. 20, 1960

This bulletin is a compilation of the reports on completed research done for the Iowa State Highway Research Board Project HR-1, "The Loess and Glacial Till Materials of Iowa; an Investigation of Their Physical and Chemical Properties and Techniques for Processing Them to Increase Their All-Weather Stability for Road Construction.” The research, started in 1950, was done by the Iowa Engineering Experiment Station under its project 283-S. The project was supported by funds from the Iowa State Highway Commission.

Provision of supplementary materials in Library and Information Science scholarly journals

Purpose This study seeks to analyse the policies of library and information science (LIS) journals regarding the publication of supplementary materials, the number of journals and articles that include this feature, the kind of supplementary materials published with regard to their function in the article, the formats employed and the access provided to readers. Design/methodology/approach The study analysed the instructions for authors of LIS journals indexed in the ISI Journal Citation Reports, as well as the supplementary materials attached to the articles published in their 2011 online volumes. Findings Large publishers are more likely to have a policy regarding the publication of supplementary materials, and policies are usually homogeneous across all the journals of a given publisher. Most policies state the acceptance of supplementary materials, and even journals without a policy also publish supplementary materials. The majority of supplementary materials provided in LIS articles are extended methodological explanations and additional results in the form of textual information in PDF or Word files. Some toll-access journals provide open access to any reader to these files. Originality/value This study provides new insights into the characteristics of supplementary materials in LIS journals. The results may be used by journal publishers to establish a policy on the publication of supplementary materials and, more broadly, to develop data sharing initiatives in academic settings.

Short-term increase in particulate matter blunts nocturnal blood pressure dipping and daytime urinary sodium excretion

Short-term exposure to ambient particulate matter with aerodynamic diameters<10 µm were found to be positively associated with blood pressure. Yet, little information exists regarding the association between particles and circadian rhythm of blood pressure. Hence, we analyzed the association of exposure to particulate matter with aerodynamic diameters<10 µm on the day of examination and ≤7 days before with ambulatory blood pressure and with sodium excretion in 359 adults from the general population using multiple linear regression. After controlling for potential confounders, a 10-µg/m3 increase in particulate matter with aerodynamic diameters<10 µm levels was associated with nighttime systolic blood pressure (β=1.32 mm Hg 95% CI, 0.06-2.58 mm Hg at lag 0; P=0.04), nighttime diastolic blood pressure (0.72 mm Hg 95% CI, 0.03-1.42 mm Hg at lag 2; P=0.04), nocturnal systolic blood pressure dipping (-0.96 mm Hg 95% CI, -1.89 to -0.03 mm Hg at lag 0; P=0.044), and daytime urinary sodium excretion (-0.05 log-mmol/min 95% CI, -0.10 to -0.01 log-mmol/min at lag 0; P=0.027) but not with nighttime sodium excretion. The associations with blood pressure rapidly diminished with increasing lag days, and the associations with daytime sodium excretion were maximal with particulate matter with aerodynamic diameters<10 µm in exposures 2 to 5 days before. The associations of short-term increases in particulate matter with aerodynamic diameters<10 µm with higher nighttime blood pressure and blunted systolic blood pressure dipping were preceded by associations with reduced ability of the kidney to excrete sodium during daytime. The underlying mechanism linking air pollution to increased cardiovascular risk may include disturbed circadian rhythms of renal sodium handling and blood pressure.

Effects of particulate matters on inflammatory markers in the general adult population

Summary: Particulate air pollution is associated with increased cardiovascular risk. The induction of systemic inflammation following particle inhalation represents a plausible mechanistic pathway. The purpose of this study was to assess the associations of short-term exposure to ambient particulate matters of aerodynamic diameter less than 10 μm (PM10) with circulating inflammatory markers in 6183 adults in Lausanne, Switzerland. The results show that short-term exposure to PM10 was associated with higher levels of circulating IL-6 and TNF-α. The positive association of PM10 with markers of systemic inflammation materializes the link between air pollution and cardiovascular risk. Background: Variations in short-term exposure to particulate matters (PM) have been repeatedly associated with daily all-cause mortality. Particle-induced inflammation has been postulated to be one of the important mechanisms for increased cardiovascular risk. Experimental in-vitro, in-vivo and controlled human studies suggest that interleukin 6 (IL-6) and tumor-necrosis-factor alpha (TNF-α) could represent key mediators of the inflammatory response to PM. The associations of short-term exposure to ambient PM with circulating inflammatory markers have been inconsistent in studies including specific subgroups so far. The epidemiological evidence linking short-term exposure to ambient PM and systemic inflammation in the general population is scarce. So far, large-scale population-based studies have not explored important inflammatory markers such as IL-6, IL-1β or TNF-α. We therefore analyzed the associations between short-term exposure to ambient PM10 and circulating levels of high-sensitive CRP (hs-CRP), IL-6, IL-1β and TNF-α in the population-based CoLaus study. Objectives: To assess the associations of short-term exposure to ambient particulate matters of aerodynamic diameter less than 10 μm (PM10) with circulating inflammatory markers, including hs-CRP, IL-6, IL-1β and TNF-α, in adults aged 35 to 75 years from the general population. Methodology: All study subjects were participants to the CoLaus study (www.colaus.ch) and the baseline examination was carried out from 2003 to 2006. Overall, 6184 participants were included. For the present analysis, 6183 participants had data on at least one of the four measured circulating inflammatory markers. The monitoring data was obtained from the website of Swiss National Air Pollution Monitoring Network (NABEL). We analyzed data on PM10 as well as outside air temperature, pressure and humidity. Hourly concentrations of PM10 were collected from 1 January 2003 to 31 December 2006. Robust linear regression (PROC ROBUSTREG) was used to evaluate the relationship between cytokine inflammatory and PM10. We adjusted all analyses for age, sex, body mass index, smoking status, alcohol consumption, diabetes status, hypertension status, education levels, zip code, and statin intake. All data were adjusted for the effects of weather by including temperature, barometric pressure, and season as covariates in the adjusted models. We performed simple and multiple logistic regression analyses. Descriptive statistical analysis used the Wilcoxon rank sum test (for medians). All data analyses were performed using SAS software (version 9.2; SAS Institute Inc., Cary, NC, USA), and a two-sided significance level of 5% was used. Results: PM10 levels averaged over 24 hours were significantly and positively associated with continuous IL-6 and TNF-α levels, in the whole study population both in unadjusted and adjusted analyses. For each cytokine, there was a similar seasonal pattern, with wider confidence intervals in summer than during the other seasons, which might partly be due to the smaller number of participants examined in summer. The associations of PM10 with IL-6 and TNF-α were also found after having dichotomized these cytokines into high versus low levels, which suggests that the associations of PM10 with the continuous cytokine levels are very robust to any distributional assumption and to potential outlier values. In contrast with what we observed for continuous IL-1β levels, high PM10 levels were significantly associated with high IL-1β. PM10 was significantly associated with IL-6 and TNF-α in men, but with TNF-α only in women. However, there was no significant statistical interaction between PM10 and sex. For IL-6 and TNF-α, the associations tended to be stronger in younger people, with a significant interaction between PM10 and age groups for IL-6. PM10 was significantly associated with IL-6 and TNF-α in the healthy group and also in the "non-healthy" group, although the statistical interaction between healthy status and PM10 was not significant. Conclusion: In summary, we found significant independent positive associations of short-term exposure to PM10 with circulating levels of IL-6 and TNF-α in the adult population of Lausanne. Our findings strongly support the idea that short-term exposure to PM10 is sufficient to induce systemic inflammation on a broad scale in the general population. From a public health perspective, the reported association of elevated inflammatory cytokines with short-term exposure to PM10 in a city with relatively clean air such as Lausanne supports the importance of limiting urban air pollution levels.

Els materials arqueològics del jaciment ibèric de la Serra de l’Espasa (Capçanes, Priorat) dipositats al Museu d’Arqueologia Salvador Vilaseca de Reus: evidències d’un santuari?

En aquest treball presentem una revisió del jaciment ibèric de la Serra de l’Espasa (Capçanes, Priorat) a partir de l’estudi, amb criteris actualitzats, del material conservat en el Museu Salvador Vilaseca de Reus. Els resultats són contrastats amb les darreres investigacions arqueològiques desenvolupades en el curs inferior de l’Ebre. A l’últim, s’analitzen les possibles interpretacions d’aquest conjunt, en particular la hipotètica existència d’un santuari, i les seves implicacions en el procés de romanització en aquesta zona.

Nou portal d'accés als materials en obert de la UdG : DUGi 2.0

La Biblioteca de la Universitat de Girona és l'encarregada de coordinar els repositoris digitals de la Universitat. A l'inici el repositori neix de la necessitat de difondre i preservar tota la recerca de la Universitat, però mica en mica el projecte va creixent i es creen diferents repositoris per a diferents tipus de continguts. Així es creen els repositoris DUGiDocs, DUGiMedia i DUGiFonsEspecials.L'objectiu d'aquest PFC és desenvolupar un portal web amb un sistema d'indexació que permeti la cerca per diferents criteris com, per exemple, autor, matèria i títol. L'entorn ha de tenir un disseny agradable per a l'usuari final i ha de permetre obtenir les dades del repositori que se li indiquin. També ha de ser capaç de detectar els possibles duplicats en els criteris de cerca i notificar-ho a l'administrador

Nou portal d'accés als materials en obert de la UdG : DUGi 2.0

La Biblioteca de la Universitat de Girona és l'encarregada de coordinar els repositoris digitals de la Universitat. A l'inici el repositori neix de la necessitat de difondre i preservar tota la recerca de la Universitat, però mica en mica el projecte va creixent i es creen diferents repositoris per a diferents tipus de continguts. Així es creen els repositoris DUGiDocs, DUGiMedia i DUGiFonsEspecials.L'objectiu d'aquest PFC és desenvolupar un portal web amb un sistema d'indexació que permeti la cerca per diferents criteris com, per exemple, autor, matèria i títol. L'entorn ha de tenir un disseny agradable per a l'usuari final i ha de permetre obtenir les dades del repositori que se li indiquin. També ha de ser capaç de detectar els possibles duplicats en els criteris de cerca i notificar-ho a l'administrador

Analysis of thermal properties of phase change materials (PCM) using differential scanning calorimeter (DSC)

Commercially available PCM RT 20, RT 27, SP 22, A17 and SP 25 A8. Were analyzed using dynamic and step method of heat flux DSC. The results of the dinamic and step method were compared with commercial valures. It was found that RT 20 & RT 27 showed good conforming of results with commercial values while SP 22 A17 & SP 25 A8 did not show conformity.

Improvement of the thermal performance of commercial freezers using phase change materials (PCM)

The aim of this work is to improve the thermal performance of commercial freezers using phase change materials (PCM) and the prove the importance of the correct PCM selection (melting temperature) for each application. To do this a vertical freezer with and without macro encapsulation PCM are used to assess the benefits of using PCM in minimizing temperature fluctuations and to maintain at the lowest possible temperature the freezer under heat of losses.

Theoretical Analysis and Simulations of Vertically Vibrated Granular Materials

The dynamical properties ofshaken granular materials are important in many industrial applications where the shaking is used to mix, segregate and transport them. In this work asystematic, large scale simulation study has been performed to investigate the rheology of dense granular media, in the presence of gas, in a three dimensional vertical cylinder filled with glass balls. The base wall of the cylinder is subjected to sinusoidal oscillation in the vertical direction. The viscoelastic behavior of glass balls during a collision, have been studied experimentally using a modified Newton's Cradle device. By analyzing the results of the measurements, using numerical model based on finite element method, the viscous damping coefficient was determinedfor the glass balls. To obtain detailed information about the interparticle interactions in a shaker, a simplified model for collision between particles of a granular material was proposed. In order to simulate the flow of surrounding gas, a formulation of the equations for fluid flow in a porous medium including particle forces was proposed. These equations are solved with Large Eddy Simulation (LES) technique using a subgrid-model originally proposed for compressible turbulent flows. For a pentagonal prism-shaped container under vertical vibrations, the results show that oscillon type structures were formed. Oscillons are highly localized particle-like excitations of the granular layer. This self-sustaining state was named by analogy with its closest large-scale analogy, the soliton, which was first documented by J.S. Russell in 1834. The results which has been reportedbyBordbar and Zamankhan(2005b)also show that slightly revised fluctuation-dissipation theorem might apply to shaken sand, which appears to be asystem far from equilibrium and could exhibit strong spatial and temporal variations in quantities such as density and local particle velocity. In this light, hydrodynamic type continuum equations were presented for describing the deformation and flow of dense gas-particle mixtures. The constitutive equation used for the stress tensor provides an effective viscosity with a liquid-like character at low shear rates and a gaseous-like behavior at high shear rates. The numerical solutions were obtained for the aforementioned hydrodynamic equations for predicting the flow dynamics ofdense mixture of gas and particles in vertical cylindrical containers. For a heptagonal prism shaped container under vertical vibrations, the model results were found to predict bubbling behavior analogous to those observed experimentally. This bubbling behavior may be explained by the unusual gas pressure distribution found in the bed. In addition, oscillon type structures were found to be formed using a vertically vibrated, pentagonal prism shaped container in agreement with computer simulation results. These observations suggest that the pressure distribution plays a key rolein deformation and flow of dense mixtures of gas and particles under vertical vibrations. The present models provide greater insight toward the explanation of poorly understood hydrodynamic phenomena in the field of granular flows and dense gas-particle mixtures. The models can be generalized to investigate the granular material-container wall interactions which would be an issue of high interests in the industrial applications. By following this approach ideal processing conditions and powder transport can be created in industrial systems.

Mass transfer and particleinteractions in granular systems and suspension flows

The purpose of this study was to investigate some important features of granular flows and suspension flows by computational simulation methods. Granular materials have been considered as an independent state ofmatter because of their complex behaviors. They sometimes behave like a solid, sometimes like a fluid, and sometimes can contain both phases in equilibrium. The computer simulation of dense shear granular flows of monodisperse, spherical particles shows that the collisional model of contacts yields the coexistence of solid and fluid phases while the frictional model represents a uniform flow of fluid phase. However, a comparison between the stress signals from the simulations and experiments revealed that the collisional model would result a proper match with the experimental evidences. Although the effect of gravity is found to beimportant in sedimentation of solid part, the stick-slip behavior associated with the collisional model looks more similar to that of experiments. The mathematical formulations based on the kinetic theory have been derived for the moderatesolid volume fractions with the assumption of the homogeneity of flow. In orderto make some simulations which can provide such an ideal flow, the simulation of unbounded granular shear flows was performed. Therefore, the homogeneous flow properties could be achieved in the moderate solid volume fractions. A new algorithm, namely the nonequilibrium approach was introduced to show the features of self-diffusion in the granular flows. Using this algorithm a one way flow can beextracted from the entire flow, which not only provides a straightforward calculation of self-diffusion coefficient but also can qualitatively determine the deviation of self-diffusion from the linear law at some regions nearby the wall inbounded flows. Anyhow, the average lateral self-diffusion coefficient, which was calculated by the aforementioned method, showed a desirable agreement with thepredictions of kinetic theory formulation. In the continuation of computer simulation of shear granular flows, some numerical and theoretical investigations were carried out on mass transfer and particle interactions in particulate flows. In this context, the boundary element method and its combination with the spectral method using the special capabilities of wavelets have been introduced as theefficient numerical methods to solve the governing equations of mass transfer in particulate flows. A theoretical formulation of fluid dispersivity in suspension flows revealed that the fluid dispersivity depends upon the fluid properties and particle parameters as well as the fluid-particle and particle-particle interactions.

Transport i emmagatzematge de les àmfores en l'antiguitat:l'aportació de les ciències dels materials

[spa]Las ánforas son ejemplos claros de cerámicas utilitarias que requieren de unas características técnicas necesarias para cumplir su funcionalidad: servir de envase de almacenamiento y transporte. En este trabajo se propone el estudio del comportamiento funcional de estos envases a través de la evaluación de las propiedades mecánicas de resistencia y tenacidad a la fractura. Propiedades mecánicas, ámforas ibéricas, ámforas romanas, tecnología, funcionalidad.

Revegetació de talussos d'una explotació carbonífera mitjançant materials de rebuig

En aquest treball s'avalua la rehabilitació dels talussos d'una explotació minera carbonífera utilitzant materials de rebuig de la pròpia explotació i provinents d'activitats ramaderes (purins de porc) o urbanes (llots de depuradora), en un ambient àrid del Baix Segre. Les variables analitzades foren el tipus i recobriment vegetals, la penetromia i la salinitat del substrat, i la salinitat, els nitrats i els sediments dels efluents. Els resultats indiquen que és possible rehabilitar els runams en aquests medis, assolint recobriments vegetals fins al 50 % sense que se'n derivin efectes ambientals negatius importants. Taxes altes puntuals d'erosió poden controlar-se amb un disseny adient dels talussos. L'aplicació superficial de purí no té efectes antiencrostants. La moderada salinitat dels substrats condiciona l'establiment de vegetació halòfila.