UV Radiation as an Attractor for Insects

Light pollution due to exterior lighting is a rising concern. While glare, light trespass and general light pollution have been well described, there are few reported studies on the impact of light pollution on insects. By studying insect behavior in relation to artificial lighting, we suggest that control of the UV component of artificial lighting can significantly reduce its attractiveness, offering a strong ability to control the impact on insects. Traditionally, the attractiveness of a lamp to insects is calculated using the luminous efficiency spectrum of insect rhodopsin. This has enabled the development of lamps that emit radiation with wavelengths that are less visible to insects (that is, yellow lamps). We tested the assumption that the degree of visibility of a lamp to insects can predict its attractiveness by means of experimental collections. We found that the expected lamp's visibility is indeed related to the extent to which it attracts insects. However, the number of insects attracted to a lamp is disproportionally affected by the emission of ultraviolet radiation. UV triggers the behavior of approaching lights more or less independently of the amount of UV radiation emitted. Thus, even small amounts of UV should be controlled in order to develop bug-free lamps.

Solid electrolytes for electrochromic devices based on reversible metal electrodeposition

Air conditioning and lighting costs can be reduced substantially by changing the optical properties of "intelligent windows." The electrochromic devices studied to date have used copper as an additive. Copper, used here as an electrochromic material, was dissolved in an aqueous animal protein-derived gel electrolyte. This combination constitutes the electrochromic system for reversible electrodeposition. Cyclic voltammetry, chronoamperometric and chromogenic analyses indicated that were obtained good conditions of transparency (initial transmittance of 70%), optical reversibility, small potential window (2.1 V), variation of transmittance in visible light (63.6%) and near infrared (20%) spectral regions. Permanence in the darkened state was achieved by maintaining a lower pulse potential (-0.16 V) than the deposition potential (-1.0 V). Increasing the number of deposition and dissolution cycles favored the transmittance and photoelectrochemical reversibility of the device. The conductivity of the electrolyte (10(-3) S/cm) at several concentrations of CuCl2 was determined by electrochemical impedance spectroscopy. A thermogravimetric analysis confirmed the good thermal stability of the electrolyte, since the mass loss detected up to 100 degrees C corresponded to water evaporation and decomposition of the gel started only at 200 degrees C. Micrographic and small angle X-ray scattering analyses indicated the formation of a persistent deposit of copper particles on the ITO. (C) 2012 Elsevier B.V. All rights reserved.

AVALIAÇÃO DOS INCÊNDIOS FLORESTAIS OCORRIDOS NO PARQUE NACIONAL DA SERRA DA CANASTRA - MINAS GERAIS

Neste trabalho, objetivou-se estabelecer o perfil dos incêndios florestais ocorridos no Parque Nacional da serra da Canastra, utilizando dados contidos nos Relatórios de Ocorrências de Incêndios de 1988 até 2008, cedidos pela unidade de conservação. Foram registradas 219 ocorrências, totalizando 415572,50 ha de área queimada, com média de 10,43 incêndios e 19789,17 ha queimados por ano. Em relação à área queimada, os incêndios causados por incendiários apresentaram o maior valor, seguido por queimas para limpeza de pastagens, raios e causa desconhecida. Considerando-se número de ocorrências, os incêndios decorrentes de raios apresentaram a maior frequência. Nos meses de setembro e agosto predominaram os incêndios causados por incendiários e de causa desconhecida, enquanto os incêndios naturais ocorreram principalmente nos meses de outubro e fevereiro e os decorrentes da queima para limpeza de pastagens se concentraram em julho. Os incêndios que atingiram maiores áreas foram observados em locais com maior declividade, enquanto os de menores proporções ocorreram em áreas planas e ou de relevos suaves. Quanto à localização, registrou-se o maior número de focos na área regularizada do parque, provavelmente por ser esta área a mais fiscalizada.

Quantitative analysis of photodynamic therapy effects in rat mammary tumor vascular density using image-pro plus software

Photodynamic therapy (PDT) is a treatment modality that has advanced rapidly in recent years. It causes tissue and vascular damage with the interaction of a photosensitizing agent (PS), light of a proper wavelength, and molecular oxygen. Evaluation of vessel damage usually relies on histopathology evaluation. Results are often qualitative or at best semi-quantitative based on a subjective system. The aim of this study was to evaluate, using CD31 immunohistochem- istry and image analysis software, the vascular damage after PDT in a well-established rodent model of chemically induced mammary tumor. Fourteen Sprague-Dawley rats received a single dose of 7,12-dimethylbenz(a)anthraxcene (80 mg/kg by gavage), treatment efficacy was evaluated by comparing the vascular density of tumors after treatment with Photogem® as a PS, intraperitoneally, followed by interstitial fiber optic lighting, from a diode laser, at 200 mW/cm and light dose of 100 J/cm directed against his tumor (7 animals), with a control group (6 animals, no PDT). The animals were euthanized 30 hours after the lighting and mammary tumors were removed and samples from each lesion were formalin-fixed. Immunostained blood vessels were quantified by Image Pro-Plus version 7.0. The control group had an average of 3368.6 ± 4027.1 pixels per picture and the treated group had an average of 779 ± 1242.6 pixels per area (P < 0.01), indicating that PDT caused a significant decrease in vascular density of mammary tumors. The combined immu- nohistochemistry using CD31, with selection of representative areas by a trained pathology, followed by quantification of staining using Image Pro-Plus version 7.0 system was a practical and robust methodology for vessel damage evalua- tion, which probably could be used to assess other antiangiogenic treatments.

Optimización del cultivo de diatomeas bentónicas para el cultivo de post-larvas de abalón ("Haliotis tuberculata coccinea" Reeve, 1846)

[EN] Diatom cell quantity and their biochemical composition vary among species and are greatly affected by harvest stage or culture conditions. Biometric parameters, growth, attachment capacity and variations in biochemical composition of four species of benthic diatoms (Amphora sp., Navicula incerta, Nitzschia sp. and Proschkinia sp.) were studied. For biochemical analysis the diatoms were harvested at different stages, in log and stationary phase of growth. The culture conditions were identical for all the experiments, benthic diatoms were cultured during 7 days in F/2 medium at 28.5 ± 1.4 ºC, at different original inoculating densities (50000, 100000, and 250000 cell mL-1), under continuous light of 5403 ± 649 Lux provided by cool white fluorescent lighting. The cultures were neither aerated nor agitated. These results show that the specific density of 10000 cell mL-1 was the best for weekly production: Proschkinia sp. reached the highest cell density of 5.81 x 106 cells mL-1 and Amphora sp. had the highest cell attachment capacity with 12000 cell mm-2, in stationary phase of growth. Protein and lipid content were higher in log phase than in stationary phase for the four diatoms. Amphora sp. in log phase of growth had the highest lipid content of 9.74% dry weight (DW). Polyunsaturated fatty acid (PUFA) content ranged from 23.25% to 38.62% of the total fatty acids (TFA), and the four diatoms tested were richer in n-3 PUFA than in n-6 PUFA. All the diatoms had significant quantities of 20:5n-3 (EPA) ranging between 12.69% and 17.68% of TFA. Benthic diatoms play an important and critical role in abalone culture as they are the principal food source of abalone post-larvae. Therefore, it is necessary to improve diatom quantity and quality to optimize post-larval nutrition and the consistency of production, resulting in an increase in growth and survival of abalones.

Copper(I) phenanthroline complexes and supramolecular systems containing fullerenes: Photophysics, photochemistry and potential applications in sustainable energy technologies.

Chemistry can contribute, in many different ways to solve the challenges we are facing to modify our inefficient and fossil-fuel based energy system. The present work was motivated by the search for efficient photoactive materials to be employed in the context of the energy problem: materials to be utilized in energy efficient devices and in the production of renewable electricity and fuels. We presented a new class of copper complexes, that could find application in lighting techhnologies, by serving as luminescent materials in LEC, OLED, WOLED devices. These technologies may provide substantial energy savings in the lighting sector. Moreover, recently, copper complexes have been used as light harvesting compounds in dye sensitized photoelectrochemical solar cells, which offer a viable alternative to silicon-based photovoltaic technologies. We presented also a few supramolecular systems containing fullerene, e.g. dendrimers, dyads and triads.The most complex among these arrays, which contain porphyrin moieties, are presented in the final chapter. They undergo photoinduced energy- and electron transfer processes also with long-lived charge separated states, i.e. the fundamental processes to power artificial photosynthetic systems.

Archaeological Baltic amber: degradation mechanisms and conservation measures

The aim of this project was to achieve a deep understanding of the mechanisms by which Baltic amber degrades, in order to develop techniques for preventive conservation of archaeological amber objects belonging to the National Museum of Denmark’s collections. To examine deterioration of Baltic amber, a starting point was to identify and monitor surface and bulk properties which are affected during degradation. The way to operate consisted of the use of accelerated ageing to initiate degradation of raw Baltic amber samples in different conditions of relative humidity, oxygen exposure or pH and, successively, of the use of non/micro-destructive techniques to identify and quantify changes in visual, chemical and structural properties. A large piece of raw Baltic amber was used to prepare several test samples for two different kinds of accelerated ageing: thermal-ageing and photo-ageing. During the ageing, amber samples were regularly examined through several analytical techniques related to different information: appearance/colour change by visual examination, photography and colorimetry; chemical change by infrared spectroscopy, Raman spectroscopy and elemental analysis; rate of oxidation by oxygen measurement; qualitative analysis of released volatiles by gas chromatography – mass spectrometry. The obtained results were analysed through both critical evaluation and statistical study. After the interpretation of the achieved data, the main relations between amber and environmental factors during the degradation process became clearer and it was possible to identify the major pathways by which amber degrades, such as hydrolysis of esters into alcohols and carboxylic acids, thermal-oxidation and photo-oxidation of terpenoid components, depolymerisation and decomposition of the chemical structure. At the end it was possible to suggest a preventive conservation strategy based on the control of climatic, atmospheric and lighting parameters in the environment where Baltic amber objects are stored and displayed.

Effect of rearing techniques and feed composition on productive traits, bird welfare and quality of poultry products

The PhD project was focused on the study of the poultry welfare conditions and improvements. The project work was divided into 3 main research activities. A) Field evaluation of chicken meat rearing conditions kept in intensive farms. Considering the lack of published reports concerning the overall Italian rearing conditions of broiler chickens, a survey was carried out to assess the welfare conditions of broiler reared in the most important poultry companies in Italy to verify if they are in accordance with the advices given in the European proposal COM (2005) 221 final. Chicken farm conditions, carcass lesions and meat quality were investigated. 1. The densities currently used in Italy are in accordance with the European proposal COM 221 final (2005) which suggests to keep broilers at a density lower than 30-32 kg live weight/m2 and to not exceed 38-40 kg live weight/m2. 2. The mortality rates in summer and winter agree with the mortality score calculated following the formula reported in the EU Proposal COM 221 final (2005). 3. The incidence of damaged carcasses was very low and did not seem related to the stocking density. 4. The FPD scores were generally above the maximum limit advised by the EU proposal COM 221 final (2005), although the stocking densities were lower than 30-32 kg live weight per m2. 5. It can be stated that the control of the environmental conditions, particularly litter quality, appears a key issue to control the onset of foot dermatitis. B) Manipulation of several farm parameters, such litter material and depth, stocking density and light regimen to improve the chicken welfare conditions, in winter season. 1. Even though 2 different stocking densities were established in this study, the performances achieved from the chickens were almost identical among groups. 2. The FCR was significantly better in Standard conditions contrarily to birds reared in Welfare conditions with lower stocking density, more litter material and with a light program of 16 hours light and 8 hours dark. 3. In our trial, in Standard groups we observed a higher content of moisture, nitrogen and ammonia released from the litter. Therefore it can be assumed that the environmental characteristics have been positively changed by the improvements of the rearing conditions adopted for Welfare groups. 4. In Welfare groups the exhausted litters of the pens were dryer and broilers showed a lower occurrence of FPD. 5. The prevalence of hock burn lesions, like FPD, is high with poor litter quality conditions. 6. The combined effect of a lower stocking density, a greater amount of litter material and a photoperiod similar to the natural one, have positively influenced the chickens welfare status, as a matter of fact the occurrence of FPD in Welfare groups was the lowest keeping the score under the European threshold of the proposal COM 221 final(2005). C) The purpose of the third research was to study the effect of high or low stocking density of broiler chickens, different types of litter and the adoption of short or long lighting regimen on broiler welfare through the evaluation of their productivity and incidence of foot pad dermatitis during the hot season. 1. The feed efficiency was better for the Low Density than for High Density broilers. 2. The appearance of FPD was not influenced by stocking density. 3. The foot examination revealed that the lesions occurred more in birds maintained on chopped wheat straw than on wood shaving. 4. In conclusion, the adoptions of a short light regimen similar to that occurring in nature during summer reduces the feed intake without modify the growth rate thus improving the feed efficiency. Foot pad lesion were not affected neither by stocking densities nor by light regimens whereas wood shavings exerted a favourable effect in preserving foot pad in good condition. D) A study was carried out to investigate more widely the possible role of 25-hydroxycholecalciferol supplemented in the diet of a laying hen commercial strain (Lohmann brown) in comparison of diets supplemented with D3 or with D3 + 25- hydroxycholecalciferol. Egg traits during a productive cycle as well as the bone characteristics of the layers have been as well evaluated to determine if there the vitamin D3 may enhance the welfare status of the birds. 1. The weight of the egg and of its components is often greater in hens fed a diet enriched with 25-hydroxycholecalciferol. 2. Since eggs of treated groups are heavier and a larger amount of shell is needed, a direct effect on shell strength is observed. 3. At 30 and at 50 wk of age hens fed 25 hydroxycholecalciferol exhibited greater values of bone breaking force. 4. Radiographic density values obtained in the trial are always higher in hens fed with 25-hydroxycholecalciferol of both treatments: supplemented for the whole laying cycle (25D3) or from 40 weeks of age onward (D3+25D3).

Morphological and physiological responses of apple trees under photoselective colored nets

In recent years and thanks to innovative technological advances in supplemental lighting sources and photo-selective filters, light quality manipulation (i.e. spectral composition of sunlight) have demonstrated positive effects on plant performance in ornamentals and vegetable crops. However, this aspect has been much less studied in fruit trees due to the difficulty of conditioning the light environment of orchards. The aim of the present PhD research was to study the use of different colored nets with selective light transmission in the blue (400 – 500 nm), red (600 – 700 nm) and near infrared (700 – 1100 nm) wavelengths as a tool to the light quality management and its morphological and physiological effects in field-grown apple trees. Chapter I provides a review the current status on physiological and technological advances on light quality management in fruit trees. Chapter II shows the main effect of colored nets on morpho-anatomical (stomata density, mesophyll structure and leaf mass area index) characteristics in apple leaves. Chapter III provides an analysis about the effect of micro-environmental conditions under colored nets on leaf stomatal conductance and leaf photosynthetic capacity. Chapter IV describes a study approach to evaluate the impact of colored nets on fruit growth potential in apples. Summing up results obtained in the present PhD dissertation clearly demonstrate that light quality management through photo-selective colored nets presents an interesting potential for the manipulation of plant morphological and physiological traits in apple trees. Cover orchards with colored nets might be and alternative technology to address many of the most important challenges of modern fruit growing, such as: the need for the efficient use of natural resources (water, soil and nutrients) the reduction of environmental impacts and the mitigation of possible negative effects of global climate change.

La Ricostruzione 3D di Bologna nel XVI Secolo

Il lavoro presentato ha come oggetto la ricostruzione tridimensionale della città di Bologna nella sua fase rinascimentale. Tale lavoro vuole fornire un modello 3D delle architetture e degli spazi urbani utilizzabile sia per scopi di ricerca nell’ambito della storia delle città sia per un uso didattico-divulgativo nel settore del turismo culturale. La base del lavoro è una fonte iconografica di grande importanza: l’affresco raffigurante Bologna risalente al 1575 e situato in Vaticano; questa è una veduta a volo d’uccello di grandi dimensioni dell’intero tessuto urbano bolognese all’interno della terza cerchia di mura. In esso sono rappresentate in maniera particolareggiata le architetture civili e ecclesiastiche, gli spazi ortivi e cortilivi interni agli isolati e alcune importanti strutture urbane presenti in città alla fine del Cinquecento, come l’area portuale e i canali interni alla città, oggi non più visibili. La ricostruzione tridimensionale è stata realizzata tramite Blender, software per la modellazione 3D opensource, attraverso le fasi di modellazione, texturing e creazione materiali (mediante campionamento delle principali cromie presenti nell’affresco), illuminazione e animazione. Una parte della modellazione è stata poi testata all’interno di un GIS per verificare l’utilizzo delle geometrie 3D come elementi collegabili ad altre fonti storiche relative allo sviluppo urbano e quindi sfruttabili per la ricerca storica. Grande attenzione infine è stata data all’uso dei modelli virtuali a scopo didattico-divulgativo e per il turismo culturale. La modellazione è stata utilizzata all’interno di un motore grafico 3D per costruire un ambiente virtuale interattivo nel quale un utente anche non esperto possa muoversi per esplorare gli spazi urbani della Bologna del Cinquecento. In ultimo è stato impostato lo sviluppo di un’applicazione per sistemi mobile (Iphone e Ipad) al fine di fornire uno strumento per la conoscenza della città storica in mobilità, attraverso la comparazione dello stato attuale con quello ricostruito virtualmente.

Nanoscale-electrical and optical properties of iii-nitrides

III-nitrides are wide-band gap materials that have applications in both electronics and optoelectronic devices. Because to their inherent strong polarization properties, thermal stability and higher breakdown voltage in Al(Ga,In)N/GaN heterostructures, they have emerged as strong candidates for high power high frequency transistors. Nonetheless, the use of (Al,In)GaN/GaN in solid state lighting has already proved its success by the commercialization of light-emitting diodes and lasers in blue to UV-range. However, devices based on these heterostructures suffer problems associated to structural defects. This thesis primarily focuses on the nanoscale electrical characterization and the identification of these defects, their physical origin and their effect on the electrical and optical properties of the material. Since, these defects are nano-sized, the thesis deals with the understanding of the results obtained by nano and micro-characterization techniques such as atomic force microscopy(AFM), current-AFM, scanning kelvin probe microscopy (SKPM), electron beam induced current (EBIC) and scanning tunneling microscopy (STM). This allowed us to probe individual defects (dislocations and cracks) and unveil their electrical properties. Taking further advantage of these techniques,conduction mechanism in two-dimensional electron gas heterostructures was well understood and modeled. Secondarily, origin of photoluminescence was deeply investigated. Radiative transition related to confined electrons and photoexcited holes in 2DEG heterostructures was identified and many body effects in nitrides under strong optical excitations were comprehended.

Luminescent Ionic Transition-Metal Complexes for Light-Emitting Electrochemical Cells

The European Union set the ambitious target of reducing energy consumption by 20% within 2020. This goal demands a tremendous change in how we generate and consume energy and urgently calls for an aggressive policy on energy efficiency. Since 19% of the European electrical energy is used for lighting, considerable savings can be achieved with the development of novel and more efficient lighting systems. In this thesis, accomplished in the frame of the EU project CELLO, I report some selected goals we achieved attempting to develop highly efficient, flat, low cost and flexible light sources using Light-Emitting Electrochemical Cells (LECs), based on ionic cyclometalated iridium(III) complexes. After an extensive introduction about LECs and solid-state lighting in general, I focus on the research we carried out on cyclometalated iridium(III) complexes displaying deep-blue emission, which has turned out to be a rather challenging task. In order to demonstrate the wide versatility of this class of compounds, I also report a case in which some tailored iridium(III) complexes act as near-infrared (NIR) sources. In fact, standard NIR emitting devices are typically expensive and, also in this case, LECs could serve as low-cost alternatives in fields were NIR luminescence is crucial, such as telecommunications and bioimaging. Since LECs are based on only one active material, in the last chapter I stress the importance of an integrated approach toward the right selection of suitable emitters not only from the photophysical, but also from the point of view of material science. An iridium(III) complex, once in the device, is interacting with ionic liquids, metal cathodes, electric fields, etc. All these interactions should be taken in to account if Europe really wants to implement more efficient lighting paradigms, generating light beyond research labs.

Simulation of visible light communications in vehicular networks

The rapid development in the field of lighting and illumination allows low energy consumption and a rapid growth in the use, and development of solid-state sources. As the efficiency of these devices increases and their cost decreases there are predictions that they will become the dominant source for general illumination in the short term. The objective of this thesis is to study, through extensive simulations in realistic scenarios, the feasibility and exploitation of visible light communication (VLC) for vehicular ad hoc networks (VANETs) applications. A brief introduction will introduce the new scenario of smart cities in which visible light communication will become a fundamental enabling technology for the future communication systems. Specifically, this thesis focus on the acquisition of several, frequent, and small data packets from vehicles, exploited as sensors of the environment. The use of vehicles as sensors is a new paradigm to enable an efficient environment monitoring and an improved traffic management. In most cases, the sensed information must be collected at a remote control centre and one of the most challenging aspects is the uplink acquisition of data from vehicles. My thesis discusses the opportunity to take advantage of short range vehicle-to-vehicle (V2V) and vehicle-to-roadside (V2R) communications to offload the cellular networks. More specifically, it discusses the system design and assesses the obtainable cellular resource saving, by considering the impact of the percentage of vehicles equipped with short range communication devices, of the number of deployed road side units, and of the adopted routing protocol. When short range communications are concerned, WAVE/IEEE 802.11p is considered as standard for VANETs. Its use together with VLC will be considered in urban vehicular scenarios to let vehicles communicate without involving the cellular network. The study is conducted by simulation, considering both a simulation platform (SHINE, simulation platform for heterogeneous interworking networks) developed within the Wireless communication Laboratory (Wilab) of the University of Bologna and CNR, and network simulator (NS3). trying to realistically represent all the wireless network communication aspects. Specifically, simulation of vehicular system was performed and introduced in ns-3, creating a new module for the simulator. This module will help to study VLC applications in VANETs. Final observations would enhance and encourage potential research in the area and optimize performance of VLC systems applications in the future.

Einsatz eines Aerosolmassenspektrometers während der CYPHEX-Kampagne und zur Methodenentwicklung einer Echtzeitquantifizierung gasförmiger Amine

Atmosphärische Aerosole haben einen starken Einfluss auf das Klima, der bisher nur grundlegend verstanden ist und weiterer Forschung bedarf. Das atmosphärische Verhalten der Aerosolpartikel hängt maßgeblich von ihrer Größe und chemischen Zusammensetzung ab. Durch Reflexion, Absorption und Streuung des Sonnenlichtes verändern sie den Strahlungshaushalt der Erde direkt und durch ihre Einflussnahme auf die Wolkenbildung indirekt. Besonders gealterte, stark oxidierte organische Aerosole mit großem Sauerstoff-zu-Kohlenstoff-Verhältnis wirken als effektive Wolkenkondensationskeime. Neben primären Aerosolpartikeln, die direkt partikelförmig in die Atmosphäre gelangen, spielen sekundäre Aerosolpartikel eine große Rolle, die aus Vorläufergasen in der Atmosphäre entstehen. Aktuelle Forschungsergebnisse legen nahe, dass kurzkettige aliphatische Amine bei Nukleationsprozessen beteiligt sind und somit die Partikelneubildung vielerorts mitsteuern. Um die Rolle von Aminen in der Atmosphäre besser erforschen und industrielle Emissionen kontrollieren zu können, bedarf es einer zuverlässigen Methode zur Echtzeitquantifizierung gasförmiger Amine mit hoher Zeitauflösung und niedriger Nachweisgrenze.rnDas hochauflösende Flugzeit-Aerosolmassenspektrometer (HR-ToF-AMS) bietet die Möglichkeit, atmosphärische Partikel in Echtzeit zu analysieren. Dabei werden Größe, Menge und grundlegende chemische Zusammensetzung erfasst. Anorganische Aerosolbestandteile können eindeutig zugeordnet werden. Es ist jedoch kaum möglich, einzelne organische Verbindungen in den komplizierten Massenspektren atmosphärischer Aerosole zu identifizieren und quantifizieren.rnIn dieser Arbeit wird atmosphärisches Aerosol untersucht, das im Westen Zyperns während der CYPHEX-Kampagne mit einem HR-ToF-AMS gemessen wurde. An diesem Standort ist vor allem stark gealtertes Aerosol vorzufinden, das aus Zentral- und Westeuropa stammt. Lokale Einflüsse spielen fast keine Rolle. Es wurde eine durchschnittliche Massenkonzentration von 10,98 μg/m3 gefunden, zusammengesetzt aus 57 % Sulfat, 30 % organischen Bestandteilen, 12 % Ammonium, < 1 % Nitrat und < 1 % Chlorid, bezogen auf das Gewicht. Der Median des vakuum-aerodynamischen Durchmessers betrug 446,25 nm. Es wurde sehr acides Aerosol gefunden, dessen anorganische Bestandteile weitgehend der Zusammensetzung von Ammoniumhydrogensulfat entsprachen. Tag-Nacht-Schwankungen in der Zusammensetzung wurden beobachtet. Die Sulfatkonzentration und die Acidität zeigten tagsüber Maxima und nachts Minima. Konzentrationsschwankungen an Nitrat und Chlorid zeigten einen weniger ausgeprägten Rhythmus, Maxima fallen aber immer mit Minima der Sulfatkonzentration, Aerosolacidität und Umgebungstemperatur zusammen. Organische Aerosolbestandteile entsprachen stark gealtertem, schwerflüchtigem oxidiertem organischem Aerosol. Es wurde eine interne Mischung der Partikel beobachtet, die ebenfalls meist bei alten Aerosolen auftritt.rnUm mit dem HR-ToF-AMS auch einzelne organische Verbindungen identifizieren und quantifizieren zu können, wurde eine Methode entwickelt, mit der man Amine der Gasphase selektiv in künstlich erzeugte Phosphorsäurepartikel aufnimmt und so für die HR-ToF-AMS-Messung zugänglich macht. Dadurch kombiniert man die Vorteile der Online-Messung des HR-ToF-AMS mit den Vorteilen klassischer Offline-Probenahmen. So können in Echtzeit sehr einfache Massenspektren gemessen werden, in denen störende Komponenten abgetrennt sind, während die Analyten eindeutig identifiziert werden können. Systeme dieser Art wurden GTRAP-AMS (Gaseous compound TRapping in Artificially-generated Particles – Aerosol Mass Spectrometry) genannt. Kalibrierungen für (Mono)Methylamin, Dimethylamin, Trimethylamin, Diethylamin und Triethylamin ergaben Nachweisgrenzen im ppt-Bereich bei einer Zeitauflösung von 3 min. Kammerexperimente zur Aminemission von Pflanzen zeigten eine gute Übereinstimmung des neu entwickelten Systems mit einer Gasdiffusionsabscheider-Offline-Probenahme und anschließender ionenchromatographischer Analyse. Beide Methoden zeigten Reaktionen der Pflanzen auf eine Veränderung der Lichtverhältnisse, während erhöhte Ozonkonzentrationen die Aminemission nicht veränderten. Die GTRAP-AMS-Methode eignet sich bereits für die Messung von Umgebungsluftkonzentrationen an einigen Orten, für die meisten Orte reicht die Nachweisgrenze allerdings noch nicht aus. Die Technik könnte bereits zur Echtzeitkontrolle industrieller Abgasemissionen eingesetzt werden.

Rhythms of anorexigenic neuropeptides in senegalese sole: Effects of light, feeding regimes and developmental stage.

Increasing knowledge on the endocrine mechanisms that regulate feeding and growth in cultured fish can contribute to make improvement in fish holding conditions and feeding strategies, supporting the development of new techniques that could ameliorate feeding, food conversion efficiency and growth in aquaculture practice. The main objective of this study was to investigate how daily mRNA expression of three specific anorexigenic hormones, i.e. the corticotropin-releasing hormone (CRH) and the paralogues α- and β- proopiomelanocortin (POMC), is modulated by different photoperiods, light spectra and feeding regimes, in both adult and larvae of Solea senegalensis. In addition, as Senegalese sole exhibits a shift from diurnal to nocturnal in locomotor activity and feeding habits during metamorphic process, we tried to elucidate if this shift is accompanied by relevant daily variations in the expression of these anorexigenic hormones before, during and after the completion of metamorphosis. In order to reach this main objective, three main experiments were developed. In a first experiment, adults were reared under LD (12 h light: 12h dark) cycle and fed at mid-light (ML), mid-dark (MD) and at random (RND). In a second experiment, adult specimens were reared in constant darkness (DD) and fed at subjective mid-light (sML) or at RND. Larvae of Senegalese sole were reared under LD cycle with white, blue or red light for 40 days. Our results show an independence of crh mRNA expression from the feeding time and suggest an endogenous control of crh expression in sole. Both pomc paralogues showed significant daily rhythms under LD conditions. The rhythms were maintained or were even more robust under DD conditions for pomc_a, but were completely abolished for pomc_b. Our results indicate an endogenous control of pomc_a expression by the molecular clock in telencephalon and diencephalon, but not in the pituitary gland. Our findings confirm for the first time the significant influence that ambient lighting has on larval growth and development in Senegalese sole, revealing an important effect of light spectra upon functional elements of this species. Our results also emphasize the importance of maintaining cycling light-dark conditions of the adequate wavelengths in aquaculture practices during early development of sole.