Post-steam-treatment of Mo/HZSM-5 catalysts: An alternative and effective approach for enhancing their catalytic performances of methane dehydroaromatization

Post-steam-treatment is a facile and effective method for improving the catalytic performances of Mo/HZSM-5 catalysts in methane dehydroaromatization under nonoxidative conditions. The treatment can enhance the stability of the catalyst and also give a higher methane conversion and a higher yield of light aromatics, as well as a decrease in the formation rate of carbonaceous deposits. (27)Al, (29)Si, and (1)H multinuclear magic angle spinning nuclear magnetic resonance, X-ray photoelectron spectroscopy, X-ray diffraction, X-ray fluorescence spectroscopy, and thermogravimetric analysis measurements as well as catalytic reaction evaluations were employed to conduct comparative studies on the properties of the catalysts before and after the post-steam-treatment. The results revealed that the number of free Bronsted acid sites per unit cell decreased, while more Mo species migrated into the HZSM-5 channels for the 6Mo/HZSM-5 catalysts after the post-steam-treatment. In addition, the average pore diameter was also larger for the post-steam-treated catalysts, and this was advantageous for mass transport of the reaction products. However, a severe post-steam-treatment, i.e., with longer treating time, of the 6Mo/HZSM-5 catalyst will lead to the formation of the Al(2)(MoO(4))(3) phases, which is detrimental to the reaction.

A QUANTITATIVE ASSESSMENT OF SOURCE CONTRIBUTIONS TO INHALABLE PARTICULATE MATTER POLLUTION IN METROPOLITAN BOSTON

In this paper, source apportionment techniques are employed to identify and quantify the major particle pollution source classes affecting a monitoring site in metropolitan Boston, MA. A Principal Component Analysis (PCA) of paniculate elemental data allows the estimation of mass contributions for five fine mass panicle source classes (soil, motor vehicle, coal related, oil and salt aerosols), and six coarse panicle source classes (soil, motor vehicle, refuse incineration, residual oil, salt and sulfate aerosols). Also derived are the elemental characteristics of those source aerosols and their contributions to the total recorded elemental concentrations (i.e. an elemental mass balance). These are estimated by applying a new approach to apportioning mass among various PCA source components: the calculation of Absolute Principal Component Scores, and the subsequent regression of daily mass and elemental concentrations on these scores.

The synthesis and characterization of novel liquid crystalline, meso-tetra[4-(3,4,5-trialkoxybenzoate)phenyl]porphyrins

Five, novel, meso-tetra[4-(3,4,5-trialkoxybenzoate)phenyl]porphyrins and their metal complexes were synthesized and their molecular structures were confirmed by H-1 NMR, FTIR spectroscopy and elemental analysis. Mesomorphic studies using DSC, polarizing optical microscope and X-ray diffraction revealed that all compounds exhibited thermotropic columnar mesophases over a wide mesophase temperature range and low liquid crystalline-crystal line transition temperature. (c) 2007 Elsevier Ltd. All rights reserved

Energy transfer and tunable luminescence properties of Eu3+ in TbBO3 microspheres via a facile hydrothermal process

Tb(1-x)BO3:xEu(3+) (x = 0-1) microsphere phosphors have been successfully prepared by a simple hydrothermal process directly without further sintering treatment. X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED), photoluminescence (PL), low-voltage cathodoluminescence (CL), and time-resolved emission spectra as well as lifetimes were used to characterize the samples.

Synthesis and characterisation of novel imidazolium-based ionic liquid crystals with a p-nitroazobenzene moiety

A novel series of compounds with different counter anions, i.e. 1-{[4-(4-nitrophenylazo)phenyloxy]}alkyl-3-methyl-1H-imidazol-3-ium bromide salts (C-n , n=3, 6, 10) and tetrafluoroborate salts (D-n , n=3, 6, 10), were synthesised by the incorporation of an imidazolium group into paraffin side chain-terminated 4-nitroazobenzene derivatives. Their chemical structures were determined by H-1 NMR, C-13 NMR, UV spectroscopy and elemental analysis.

Reducing HAuCl4 by the C-60 dianion: C-60-directed self-assembly of gold nanoparticles into novel fullerene bound gold nanoassemblies

The C-60 dianion is used to reduce tetrachloroauric acid (HAuCl4) for the first time; three-dimensional C-60 bound gold (Au-C-60) nanoclusters are obtained from C-60-directed self-assembly of gold nanoparticles due to the strong affinities of Au-C-60 and C-60-C-60. The process was monitored in situ by UV-vis-NIR spectroscopy. The resulting Au-C-60 nanoclusters were characterized using transmission electron microscopy (TEM), selected area electron diffraction (SAED), energy-dispersive spectroscopy (EDS), x-ray powder diffraction (XRD), x-ray photoelectron spectroscopy (XPS), and FT-IR and Raman spectroscopies.

Synthesis and Crystal Structure of a New 3D Copper B-Paradodecatungstate Compound: [Na-2(H2O)(8)][Na-8(H2O)(20)][Cu(en)(2)][W12O42] center dot 3H(2)O

A new polyoxotungstate complex [Na-2(H2O)(8)][Na-8(H2O)(20)][Cu(en)(2)][W12O42] center dot 3 H2O (1) (en = ethylenediamine) has been synthesized in aqueous solution and characterized by elemental analysis, IR spectroscopy and TG analysis, together with a single crystal X-ray diffraction study. In compound 1, the Cu(en)(2)(2+) complex cation links the [W12O42](12-) anions to form a I D chain, and the ID chains are further interconnected with Na-8(H2O)(20)(8+) and Na-2(H2O)(8)(2+) cations to construct a new 3D framework.

A ternary supramolecular compound of p-sulfonatocalix[8]arene with 1D channels

A ternary supramolecular complex of [Ni(bipy)(2)(H2O)](4)(C8AS)center dot 17.6(H2O) (bipy=4,4'-dimethyl-2,2'-bipyridine and C8AS = p-sulfonatocalix[8]arene) has been synthesized by a hydrothermal method and characterized by FT-IR spectroscopy, TG-DTA analysis and single crystal X-ray diffraction. In the structure. the water-soluble p-sulfonatocalix[8]arene molecule adopts a double partial cone conformation and is coordinated by four nickel atoms each of which is bonded by two 4,4'-dimethyl-2,2'-bipyridine molecules and one water molecule at the same time. The tetranuclear Subunits are stacked into an extended 3D structure with 1D water-filled channels via hydrogen bonds and C-H center dot center dot center dot pi interactions.

Synthesis and Spectrum of Novel Pyrazoline Fluorescent Compounds

Pyrazoline derivatives have been used widely in dyeing industry as fluorescent whitening agents due to their excellent capability. According to Schellhammer theory of the relation between chemical structure and fluorescent quality, six new fluorescent compounds were designed and synthesized which contained the benzothiazole group in the I-pyrazoline, the indole group in the 3-pyrazoline and the derivatives of phenyl in the 5-pyrazoline. The structure of target compounds was confirmed by IR, H-1 NMR, MS and elementary analysis. The fluorescence spectra showed that these compounds had good fluorescence. They could absorb ultraviolet light at near 353 nm. The fluorescence maximum emission wavelengths were about 430-443 nm. It was a kind of promising fluorescence compounds. The largest fluorescence emission wavelength and the fluorescence intensity were related to the substituted group of the compounds. When the 6-Br group was introduced into benzothiazole, the fluorescence emission wavelength exhibited a blue shift, and the fluorescence intensity increased.

Hydrothermal synthesis and luminescent properties of Y2O3:Tb3+ and Gd2O3:Tb3+ microrods

One-dimensional (1D) Y2O3:Tb3+ and Gd2O3:Tb3+ microrods have been successfully prepared through a large-scale and facile hydrothermal method followed by a subsequent calcination process in N-2/H-2 mixed atmosphere. X-ray diffraction (XRD), Fourier transform infrared spectroscopy (IR), thermogravimetric analysis (TGA), energy-dispersive X-ray spectra (EDX). scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED), photoluminescence (PL) and cathodoluminescence (CL) spectra as well as kinetic decays were used to characterize the samples. The as-formed products via the hydrothermal process could transform to cubic Y2O3:Tb3+ and Gd2O3:Tb3+ with the same morphology and slight shrinking in size after a postannealing process.

Preparation and Characterization of Melt Grafting 2-acrylamido-2-methyl-1-propanesulfonic Acid onto Pre-Irradiated Linear Low Density Polyethylene

Linear low density polyethylene (LLDPE) was functionalized with 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPS) by using -ray pre-irradiation in air in a twin-screw extruder. Fourier-transformed infrared spectroscopy (FT-IR) and electron spectroscopy for chemical analysis (ESCA) were used to characterize the formation of LLDPE-g-AMPS copolymers. The content of AMPS in LLDPE-g-AMPS was determined by using element analysis instrument. The effects of concentrations of monomer, reaction temperature and pre-irradiation dose on degree of grafting were investigated. The critical surface tension of LLDPE-g-AMPS was measured by using contact angle method. The influences of the degree of grafting on crystallization properties were studied by using DSC. Compared with neat LLDPE, the crystallization temperature increased about 4C, and crystallinity decreased with increasing degree of grafting. Crystallization rates of grafted LLDPE were faster than that of plain LLDPE at the same crystallization temperature.

New carbazole-based copolymers as amorphous hole-transporting materials for multilayer light-emitting diodes

New carbazole-based copolymers, which contain various concentrations of 9-alkyl-3, 6-carbazole fragments in the main chain connected via alkylene spacers, have been synthesized by Ni(0)-catalyzed Yamamoto-type aryl-aryl coupling reactions. Full characterization of the copolymer structure by NMR spectroscopy and elemental analysis is presented. These compounds represent amorphous materials of high thermal stability with glass transition temperatures of 151-162 degrees C and thermal decomposition starting at temperatures > 390 degrees C. UV-Vis absorption and photoluminescence emission of the copolymers confirmed that the effectively conjugated segment in the 3,6-linked carbazole-type copolymers is limited to dyads (dimeric units). However, copolymers with varying concentrations of the oligocarbazole chromophores demonstrate different charge injection and transport properties in multilayer light-emitting diodes with the copolymers as the hole transport and Alq(3) as the electroluminescent/electron transport layer. The device based on a copolymer composed of oligocarbazole blocks with an average length of around four carbazoles exhibited the best overall performance with a turn-on voltage of 3.5 V, a maximal photometric efficiency of 4.1 cd center dot A(-1) and maximum brightness of about 4 200 cd center dot m(-2).

Study on stimulated emission of Eu2+ in crystal KMgF3 : Eu2+

The line emission peak of Eu2+ ion in crystal KMgF3 is at 360 nm. The probability of stimulated emission on 4f(7) (P-6(7/2))-> 4f(7)(S-8(7/2)) transition was predicted with a four-level decay model of Eu2+6P7/2 excited states proposed by the authors. Optic gain and net gain coefficient (g = 11.4 +/- 3.2)cm(-1) of 360 nm emission in crystal KMgF3 : Eu2+ were measured by ASE method, and the predication was proved by experiment. The net gain coefficient can be increased by annealing or doping crystal KMgF3 : Eu2+ with Gd3+ or Ce3+.