Assessment Of various sensors for structural health monitoring for bridge weigh-in-motion (B-WIM).

In recent years, Structural Health Monitoring (SHM) systems have been developed to monitor bridge deterioration, assess real load levels and hence extend bridge life and safety. A road bridge is only safe if the stresses caused by the passing vehicles are less than the capacity of the bridge to resist them. Conventional SHM systems can be used to improve knowledge of the bridges capacity to resist stresses but generally give no information on the causes of any increase in stresses (based on measuring strain). The concept of in Bridge Weigh-in-Motion (B-WIM) is to establish axle loads, without interruption to traffic flow, by using strain sensors at a bridge soffit and subsequently converting the data to real time axle loads or stresses. Recent studies have shown it would be most beneficial to develop a portable system which can be easily attached to existing and new bridge structures for a specified monitoring period. The sensors could then be left in place while the data acquisition can be moved for various other sites. Therefore it is necessary to find accurate sensors capable of capturing peak strains under dynamic load and suitable methods for attaching these strain sensors to existing and new bridge structures. Additionally, it is important to ensure accurate strain transfer between concrete and steel, the adhesives layer and the strain sensor. This paper describes research investigating the suitably of using various sensors for the monitoring of concrete structures under dynamic vehicle load. Electrical resistance strain (ERS) gauges, vibrating wire (VW) gauges and fibre optic sensors (FOS) are commonly used for SHM. A comparative study will be carried out to select a suitable sensor for a bridge Weigh in Motion System. This study will look at fixing methods, durability, scanning rate and accuracy range. Finite element modeling is used to predict the strains which are then validated in laboratory trials.

A Novel Approach for Axle Detection in Bridge Weigh-In-Motion Systems

Bridge weigh-in-motion (B-WIM), a system that uses strain sensors to calculate the weights of trucks passing on bridges overhead, requires accurate axle location and speed information for effective performance. The success of a B-WIM system is dependent upon the accuracy of the axle detection method. It is widely recognised that any form of axle detector on the road surface is not ideal for B-WIM applications as it can cause disruption to the traffic (Ojio & Yamada 2002; Zhao et al. 2005; Chatterjee et al. 2006). Sensors under the bridge, that is Nothing-on-Road (NOR) B-WIM, can perform axle detection via data acquisition systems which can detect a peak in strain as the axle passes. The method is often successful, although not all bridges are suitable for NOR B-WIM due to limitations of the system. Significant research has been carried out to further develop the method and the NOR algorithms, but beam-and-slab bridges with deep beams still present a challenge. With these bridges, the slabs are used for axle detection, but peaks in the slab strains are sensitive to the transverse position of wheels on the beam. This next generation B-WIM research project extends the current B-WIM algorithm to the problem of axle detection and safety, thus overcoming the existing limitations in current state-of–the-art technology. Finite Element Analysis was used to determine the critical locations for axle detecting sensors and the findings were then tested in the field. In this paper, alternative strategies for axle detection were determined using Finite Element analysis and the findings were then tested in the field. The site selected for testing was in Loughbrickland, Northern Ireland, along the A1 corridor connecting the two cities of Belfast and Dublin. The structure is on a central route through the island of Ireland and has a high traffic volume which made it an optimum location for the study. Another huge benefit of the chosen location was its close proximity to a nearby self-operated weigh station. To determine the accuracy of the proposed B-WIM system and develop a knowledge base of the traffic load on the structure, a pavement WIM system was also installed on the northbound lane on the approach to the structure. The bridge structure selected for this B-WIM research comprised of 27 pre-cast prestressed concrete Y4-beams, and a cast in-situ concrete deck. The structure, a newly constructed integral bridge, spans 19 m and has an angle of skew of 22.7°.

A validated UPLC–MS/MS method for the surveillance of ten aquatic biotoxins in European brackish and freshwater systems

Over the past few decades, there has been an increased frequency and duration of cyanobacterial Harmful Algal Blooms (HABs) in freshwater systems globally. These can produce secondary metabolites called cyanotoxins, many of which are hepatotoxins, raising concerns about repeated exposure through ingestion of contaminated drinking water or food or through recreational activities such as bathing/ swimming. An ultra-performance liquid chromatography tandem mass spectrometry (UPLC–MS/MS) multi-toxin method has been developed and validated for freshwater cyanotoxins; microcystins-LR, -YR, -RR, -LA, -LY and -LF, nodularin, cylindrospermopsin, anatoxin-a and the marine diatom toxin domoic acid. Separation was achieved in around 9 min and dual SPE was incorporated providing detection limits of between 0.3 and 5.6 ng/L of original sample. Intra- and inter-day precision analysis showed relative
standard deviations (RSD) of 1.2–9.6% and 1.3–12.0% respectively. The method was applied to the analysis of aquatic samples (n = 206) from six European countries. The main class detected were the hepatotoxins; microcystin-YR (n = 22), cylindrospermopsin (n = 25), microcystin-RR (n = 17), microcystin-LR (n = 12), microcystin-LY (n = 1), microcystin-LF (n = 1) and nodularin (n = 5). For microcystins, the levels detected ranged from 0.001 to 1.51 mg/L, with two samples showing combined levels above the guideline set by the WHO of 1 mg/L for microcystin-LR. Several samples presented with multiple toxins indicating the potential for synergistic effects and possibly enhanced toxicity. This is the first published pan European survey of freshwater bodies for multiple biotoxins, including two identified for the first time; cylindrospermopsin in Ireland and nodularin in Germany, presenting further incentives for improved monitoring and development of strategies to mitigate human exposure.

Microneedle arrays as transdermal and intradermal drug delivery systems: Materials science, manufacture and commercial development

Transdermal drug delivery offers a number of advantages for the patient, due not only its non-invasive and convenient nature, but also factors such as avoidance of first pass metabolism and prevention of gastrointestinal degradation. It has been demonstrated that microneedle arrays can increase the number of compounds amenable to transdermal delivery by penetrating the skin's protective barrier, the stratum corneum, and creating a pathway for drug permeation to the dermal tissue below. Microneedles have been extensively investigated in recent decades for drug and vaccine delivery as well as minimally invasive patient monitoring/diagnosis. This review focuses on a range of critically important aspects of microneedle technology, namely their material composition, manufacturing techniques, methods of evaluation and commercial translation to the clinic for patient benefit and economic return. Microneedle research and development is finally now at the stage where commercialisation is a realistic possibility. However, progress is still required in the areas of scaled-up manufacture and regulatory approval.

Determinant factors for the use of imposex in TBT pollution monitoring

Os compostos de tributilestanho (TBT) foram utilizados como biocidas em tintas antivegetativas (AV) e amplamente aplicados, durante décadas, de forma a evitar a bioincrustação em superfícies submersas, principalmente em cascos de embarcações. Os seus efeitos deletérios em organismos não-alvo tornaram-se evidentes após o aparecimento de gastrópodes prosobrâquios com imposex – sobreposição de caracteres sexuais masculinos sobre o tracto reprodutivo das fêmeas. Desde então, a expressão do imposex em prosobrânquios tem sido amplamente utilizada como biomarcador da poluição por TBT. Um dos objectivos da presente tese é avaliar se as mais recentes restrições legais na utilização das tintas AV com compostos organoestânicos (OTs) resultaram numa redução da poluição pelos mesmos na costa continental Portuguesa. Para tal, foi levada a cabo a análise da variação temporal do imposex como biomarcador dos níveis ambientais de TBT e a validação de procedimentos, de modo a seguir de forma precisa a evolução da intensidade deste fenómeno ao longo do tempo. O trabalho de investigação teve início no momento em que a ineficácia da legislação anterior (Directiva 89/677/CEE) na redução da poluição por TBT no litoral Português era reportada na literatura e quando estavam já agendados instrumentos decisivos para a diminuição definitiva deste tipo de poluição: o Regulamento (CE) N.º 782/2003 do Parlamento e do Conselho da União Europeia (UE) que bania as tintas AV baseadas em TBT na sua frota a partir de 1 de Julho de 2003; a "Convenção Internacional sobre o Controlo de Sistemas Antivegetativos Nocivos em Navios” (Convenção AFS), adoptada em 2001 pela Organização Marítima Internacional (OMI), que procurava erradicar os OTs da frota mundial até 2008. Os níveis de imposex e as concentrações de OTs nos tecidos de fêmeas de Nucella lapillus foram medidos em 17 locais de amostragem ao longo da costa Portuguesa em 2003, a fim de se avaliarem os impactos do TBT nas populações desta espécie e de se criar uma base de dados para seguir a sua evolução futura. O índice da sequência do vaso deferente (VDSI), o índice do tamanho relativo do pénis (RPSI) e a percentagem de fêmeas afectadas por imposex (%I) foram utilizados na medição da intensidade deste fenómeno em cada local de amostragem e os seus valores variaram entre 0,20-4,04, 0,0- 42,2% e 16,7-100,0%, respectivamente. Foram encontradas fêmeas estéreis em 3 locais de amostragem, com percentagens a variar entre 4,0 e 6,2%. As concentrações de TBT e dibutilestanho (DBT) nas fêmeas variaram respectivamente entre 23-138 e <10-62 ng Sn.g-1 de peso seco, e o conteúdo em TBT nos tecidos revelou-se significativamente correlacionado com o imposex (nomeadamente com o RPSI e o VDSI). Os níveis de expressão do fenómeno e o conteúdo em OTs nos tecidos, foram superiores na proximidade de portos, confirmando as conclusões obtidas anteriormente por outros autores de que os navios e a actividade dos estaleiros são as principais fontes destes compostos no litoral Português. As infra-estruturas associadas ás principais fontes de OTs – portos, estaleiros e marinas – estão geralmente localizadas no interior de estuários, motivo pelo qual estas áreas têm vindo a ser descritas como as mais afectadas por estes poluentes. Por esta razão, foi levado a cabo o estudo pormenorizado da poluição por TBT na Ria de Aveiro, como caso de estudo representativo da poluição por estes compostos num sistema estuarino em Portugal continental. N. lapillus foi usada como bioindicador para avaliar a tendência temporal da poluição por TBT nesta área entre 1997 e 2007. Foi registada uma diminuição da intensidade do imposex após 2003, embora as melhorias mais evidentes tenham sido observadas entre 2005 e 2007, provavelmente devido à implementação do Regulamento (CE) N.º 782/2003 que proibiu a aplicação de tintas AV com TBT em navios com a bandeira da UE. Apesar desses progressos, as análises ao conteúdo em OTs nos tecidos de fêmeas de N. lapillus e em amostras de água colhidas em 2006 indicaram contaminação recente por TBT na área de estudo, evidenciando assim a permanência de fontes de poluição. A utilização de N. lapillus como bioindicador da poluição por TBT na Ria de Aveiro apresenta algumas limitações uma vez que a espécie não ocorre nas áreas mais interiores da Ria e não vive em contacto com sedimentos. Assim, a informação obtida a partir da sua utilização como bioindicador é fundamentalmente relativa aos níveis de TBT na coluna de água. Foi então necessário recorrer a um bioindicador complementar – Hydrobia ulvae – para melhor avaliar a evolução temporal da poluição por TBT no interior deste sistema estuarino e estudar a persistência de TBT nos sedimentos. Não foi registada uma diminuição dos níveis de imposex em H. ulvae na Ria de Aveiro entre 1998 e 2007, apesar da aplicação do Regulamento (CE) N.º 782/2003. Pelo contrário, houve um aumento global significativo da percentagem de fêmeas afectadas por imposex e um ligeiro aumento do VDSI, contrastando com o que tem sido descrito para outros bioindicadores na Ria de Aveiro no mesmo período. Estes resultados mostram que a diferente biologia/ecologia das espécies indicadoras determina vias distintas de acumulação de TBT, apontando a importância da escolha do bioindicador dependendo do compartimento a ser monitorizado (sedimento versus água). A ingestão de sedimento como hábito alimentar em H. ulvae foi discutida como sendo a razão para a escolha da espécie como indicadora da contaminação dos sedimentos por TBT. Foram também estudados os métodos mais fiáveis para reduzir a influência de variáveis críticas na medição dos níveis de imposex em H. ulvae. As comparações de parâmetros do imposex baseados em medições do pénis devem ser sempre realizadas sob condições de narcotização bem standardizadas uma vez que este procedimento provoca um aumento significativo do comprimento do pénis (PL) em ambos os sexos. O VDSI, a % e o PL em ambos os sexos revelaram ser fortemente influenciados pelo tamanho dos espécimes: a utilização de fêmeas mais pequenas conduz à subestimação do VDSI, da %I e do PL, enquanto que diferenças no tamanho dos machos provocam variações no índice do comprimento relativo do pénis (RPLI), independentemente dos níveis de poluição por TBT. Existe, portanto, a necessidade de controlar algumas variáveis envolvidas na análise do imposex que mostraram afectar a fiabilidade dos resultados. Uma vez que N. lapillus é o principal bioindicador dos efeitos biológicos específicos do TBT para a área da OSPAR, foi também estudada a influência de algumas variáveis na avaliação dos níveis de imposex nesta espécie, especificamente as relacionadas com o ciclo reprodutor e o tamanho dos espécimes. O estudo do ciclo reprodutor e a variação sazonal/espacial do comprimento do pénis do macho (MPL) incidiu num único local no litoral Português (Areão – região de Aveiro) de forma a avaliar se o RPSI varia sazonal e espacialmente na mesma estação de amostragem e se tais variações influenciam os resultados obtidos em programas de monitorização do imposex. Nos meses de Dezembro de 2005 a Junho de 2007, foram encontrados espécimes de N. lapillus sexualmente maturos e potencialmente aptos para a reprodução. Contudo, foi também evidente um padrão sazonal do ciclo reprodutor – o estado de desenvolvimento da gametogénese nas fêmeas variou sazonalmente e ocorreu uma diminuição do volume da glândula da cápsula e do factor de condição no final do Verão / início do Outono. Contrariamente, a gametogénese nos machos não apresentou variação sazonal significativa, embora os valores mais baixos do factor de condição, do comprimento do pénis e dos volumes de esperma e da próstata tenham também sido registados no final do Verão / início do Outono. Além disso, o MPL mostrou variar, no mesmo local de amostragem, inversamente com a distância aos ninhos de cápsulas ovígeras; um aumento dos valores do MPL foi também observado em espécimes de maior tamanho. Todas estas variações no MPL introduzem desvios nos resultados da avaliação do imposex quando é usado o RPSI. A magnitude do erro envolvido foi quantificada e revelou-se superior em locais com níveis mais elevados de poluição por TBT. Apesar do RPSI ser um índice que fornece informação importante sobre os níveis de poluição por TBT, a sua interpretação deve ser cuidadosa e realizada complementarmente com os outros índices, destacando-se o VDSI como índice mais fiável e com significado biológico mais expressivo. Novas campanhas de monitorização do imposex em N. lapillus foram realizadas ao longo da costa Portuguesa em 2006 e 2008, e os resultados subsequentemente comparados com a base de dados criada em 2003,de forma a avaliar a evolução da poluição por TBT no litoral Português naquele período. Nestes estudos foram aplicados novos procedimentos na monitorização e tratamento dos dados, de forma a minimizar a variação nos índices de avaliação do imposex induzida pelos factores acima descritos, para seguir com maior consistência a tendência da poluição por TBT entre 2003 e 2008. Foi observado um declínio global significativo na intensidade de imposex na área de estudo durante o referido período e a qualidade ecológica da costa Portuguesa, segundo os termos definidos pela Comissão OSPAR, revelou melhorias notáveis após 2003 confirmando a eficácia do Regulamento (CE) N.º 782/2003. Não obstante, as populações de N. lapillus revelaram-se ainda amplamente afectadas por imposex, tendo sido detectadas emissões de TBT na água do mar ao longo da costa em 2006, apesar da restrição anteriormente referida. Estes inputs foram atribuídos principalmente aos navios que à data ainda circulavam com tintas AV com TBT aplicadas antes de 2003, uma vez que a sua utilização nas embarcações foi apenas proibida em 2008. Considerando que o Regulamento (CE) N.º 782/2003 constitui uma antecipação da proibição global da OMI que entrou em vigor em Setembro de 2008, prevê-se, por analogia, que haja uma rápida diminuição da poluição por TBT à escala mundial num futuro próximo. Na sequência desta previsão, é apresentada uma discussão teórica preliminar relativamente ás possíveis estratégias usadas por N. lapillus na recolonização de locais onde, no passado, as populações terão aparentemente sido extintas devido a níveis extremamente elevados de TBT. Estes locais são tipicamente zonas abrigadas junto de infra-estruturas portuárias, cuja recolonização por esta espécie será provavelmente muito lenta dada a mobilidade reduzida dos adultos e o ciclo de vida não apresentar fase larvar pelágica. Foram então equacionadas duas hipotéticas vias de recolonização de zonas abrigadas por espécimes provenientes de populações de costa aberta/exposta: a migração de adultos e/ou a dispersão de juvenis. No entanto, em ambos os casos, estaria implicada a transposição de um problema amplamente descrito na bibliografia: as populações de N. lapillus de costa aberta podem apresentar um fenótipo muito diferente das de zonas abrigadas, podendo inclusivamente variar no número de cromossomas. A recolonização pode portanto não ter sucesso pelo simples facto dos novos recrutas não estarem bem adaptados aos locais a recolonizar. Para analisar este problema, foram estudados tanto a forma da concha de espécimes de N. lapillus ao longo da costa Portuguesa como o respectivo número de cromossomas. Embora a forma da concha tenha revelado diferenças, de acordo com o grau de hidrodinamismo entre as populações de N. lapillus avaliadas, o cariótipo 2n = 26, típico de zonas expostas, foi registado em todos os locais amostrados. Por outro lado, foi também testada em laboratório a possível mortalidade de juvenis em dispersão no interior menos salino dos estuários. Foi então verificada a ocorrência de mortalidade elevada de juvenis expostos a salinidades baixas (=100% após 1 hora a salinidades ≤9 psu), o que também pode comprometer a recolonização de zonas estuarinas menos salinas por esta via. Mesmo assim, os juvenis mostraram um comportamento de flutuação à superfície da água em condições laboratoriais, que pode ser considerado um benefício específico na colonização de áreas mais internas dos estuários, se tal facto vier a ser confirmado em estudos de campo. As conclusões deste estudo contribuem certamente para a descrição do final da “história do TBT” dado que, uma vez controlados alguns factores determinantes no uso do imposex como biomarcador, a avaliação do declínio da poluição por estes compostos, agora esperado à escala global, se torna mais rigorosa.

Combining sampling, profiling, remote sensing and modelling to efficiently monitoring estuarine and coastal water quality

Monitoring of coastal and estuarine water quality has been traditionally performed by sampling with subsequent laboratory analysis. This has the disadvantages of low spatial and temporal resolution and high cost. In the last decades two alternative techniques have emerged to overcome this drawback: profiling and remote sensing. Profiling using multi-parameter sensors is now in a commercial stage. It can be used, tied to a boat, to obtain a quick “picture” of the system. The spatial resolution thus increases from single points to a line coincident with the boat track. The temporal resolution however remains unchanged since campaigns and resources involved are basically the same. The need for laboratory analysis was reduced but not eliminated because parameters like nutrients, microbiology or metals are still difficult to obtain with sensors and validation measurements are still needed. In the last years the improvement in satellite resolution has enabled its use for coastal and estuarine water monitoring. Although spatial coverage and resolution of satellite images in the present is already suitable to coastal and estuarine monitoring, temporal resolution is naturally limited to satellite passages and cloud cover. With this panorama the best approach to water monitoring is to integrate and combine data from all these sources. The natural tools to perform this integration are numerical models. Models benefit from the different sources of data to obtain a better calibration. After calibration they can be used to extend spatially and temporally the methods resolution. In Algarve (South of Portugal) a monitoring effort using this approach is being undertaken. The monitoring effort comprises five different locations including coastal waters, estuaries and coastal lagoons. The objective is to establish the base line situation to evaluate the impact of Waste Water Treatment Plants design and retrofitting. The field campaigns include monthly synoptic profiling, using an YSI 6600 multi-parameter system, laboratory analysis and fixed stations. The remote sensing uses ENVISAT\MERIS Level 2 Full Resolution data. This data is combined and used with the MOHID modelling system to obtain an integrate description of the systems. The results show the limitations of each method and the ability of the modelling system to integrate the results and to produce a comprehensive picture of the system.

Advanced monitoring of South Portugal water bodies towards WFD

The challenge on implementation of the EU Water Framework Directive (WFD) fosters the development of new monitoring methods and approaches. It is now commonly accepted that the use of classical monitoring campaigns in discrete point is not sufficient to fully assess and describe a water body. Due to this the WFD promote the use of modelling techniques in surface waters to assist all phases of the process, from characterisation and establishment of reference conditions to identification of pressures and assessment of impact. The work presented in this communication is based on these principles. A classical monitoring of the water status of the main transitional water bodies of Algarve (south of Portugal) is combined with advanced in situ water profiling and hydrodynamic, water quality and ecological modelling of the systems to build a complete description of its state. This approach extends spatially and temporally the resolution of the classical point sampling. The methodology was applied during a 12 month program in Ria Formosa coastal lagoon, the Guadiana estuary and the Arade estuary. The synoptic profiling uses an YSI 6600 EDS multi-parameter system attached to a boat and a GPS receiver to produce monthly synoptic maps of the systems. This data extends the discrete point sampling with laboratory analysis performed monthly in several points of each water body. The point sampling is used to calibrate the profiling system and to include variables, such as nutrients, not measured by the sensors. A total of 1427 samplings were performed for physical and chemical parameters, chlorophyll and microbiologic contamination in the water column. This data is used to drive the hydrodynamic, transport and ecological modules of the MOHID water modelling system (www.mohid.com), enabling an integrate description of the water column.

Primary production in systems subject to natural and anthropogenic eutrophication

Tese dout., Química, Universidade do Algarve, 2005

Low Complexity All-Pass Based Polyphase Decimation Filters for ECG Monitoring

This paper presents a low complexity high efficiency decimation filter which can be employed in EletroCardioGram (ECG) acquisition systems. The decimation filter with a decimation ratio of 128 works along with a third order sigma delta modulator. It is designed in four stages to reduce cost and power consumption. The work reported here provides an efficient approach for the decimation process for high resolution biomedical data conversion applications by employing low complexity two-path all-pass based decimation filters. The performance of the proposed decimation chain was validated by using the MIT-BIH arrhythmia database and comparative simulations were conducted with the state of the art.

EMMON: a WSN system architecture for large scale and dense real-time embedded monitoring

Wireless sensor networks (WSNs) have attracted growing interest in the last decade as an infrastructure to support a diversity of ubiquitous computing and cyber-physical systems. However, most research work has focused on protocols or on specific applications. As a result, there remains a clear lack of effective, feasible and usable system architectures that address both functional and non-functional requirements in an integrated fashion. In this paper, we outline the EMMON system architecture for large-scale, dense, real-time embedded monitoring. EMMON provides a hierarchical communication architecture together with integrated middleware and command and control software. It has been designed to use standard commercially-available technologies, while maintaining as much flexibility as possible to meet specific applications requirements. The EMMON architecture has been validated through extensive simulation and experimental evaluation, including a 300+ node test-bed, which is, to the best of our knowledge, the largest single-site WSN test-bed in Europe to date.

Assessment of NDVI, land surface temperature and precipitation anomalies for drought monitoring in Bayankhongor province, Mongolia

During the last decade Mongolia’s region was characterized by a rapid increase of both severity and frequency of drought events, leading to pasture reduction. Drought monitoring and assessment plays an important role in the region’s early warning systems as a way to mitigate the negative impacts in social, economic and environmental sectors. Nowadays it is possible to access information related to the hydrologic cycle through remote sensing, which provides a continuous monitoring of variables over very large areas where the weather stations are sparse. The present thesis aimed to explore the possibility of using NDVI as a potential drought indicator by studying anomaly patterns and correlations with other two climate variables, LST and precipitation. The study covered the growing season (March to September) of a fifteen year period, between 2000 and 2014, for Bayankhongor province in southwest Mongolia. The datasets used were MODIS NDVI, LST and TRMM Precipitation, which processing and analysis was supported by QGIS software and Python programming language. Monthly anomaly correlations between NDVI-LST and NDVI-Precipitation were generated as well as temporal correlations for the growing season for known drought years (2001, 2002 and 2009). The results show that the three variables follow a seasonal pattern expected for a northern hemisphere region, with occurrence of the rainy season in the summer months. The values of both NDVI and precipitation are remarkably low while LST values are high, which is explained by the region’s climate and ecosystems. The NDVI average, generally, reached higher values with high precipitation values and low LST values. The year of 2001 was the driest year of the time-series, while 2003 was the wet year with healthier vegetation. Monthly correlations registered weak results with low significance, with exception of NDVI-LST and NDVI-Precipitation correlations for June, July and August of 2002. The temporal correlations for the growing season also revealed weak results. The overall relationship between the variables anomalies showed weak correlation results with low significance, which suggests that an accurate answer for predicting drought using the relation between NDVI, LST and Precipitation cannot be given. Additional research should take place in order to achieve more conclusive results. However the NDVI anomaly images show that NDVI is a suitable drought index for Bayankhongor province.

Benchmarking therapeutic drug monitoring software: A review of available computer tools

Therapeutic drug monitoring (TDM) aims to optimize treatments by individualizing dosage regimens based on the measurement of blood concentrations. Dosage individualization to maintain concentrations within a target range requires pharmacokinetic and clinical capabilities. Bayesian calculations currently represent the gold standard TDM approach but require computation assistance. In recent decades computer programs have been developed to assist clinicians in this assignment. The aim of this survey was to assess and compare computer tools designed to support TDM clinical activities. The literature and the Internet were searched to identify software. All programs were tested on personal computers. Each program was scored against a standardized grid covering pharmacokinetic relevance, user friendliness, computing aspects, interfacing and storage. A weighting factor was applied to each criterion of the grid to account for its relative importance. To assess the robustness of the software, six representative clinical vignettes were processed through each of them. Altogether, 12 software tools were identified, tested and ranked, representing a comprehensive review of the available software. Numbers of drugs handled by the software vary widely (from two to 180), and eight programs offer users the possibility of adding new drug models based on population pharmacokinetic analyses. Bayesian computation to predict dosage adaptation from blood concentration (a posteriori adjustment) is performed by ten tools, while nine are also able to propose a priori dosage regimens, based only on individual patient covariates such as age, sex and bodyweight. Among those applying Bayesian calculation, MM-USC*PACK© uses the non-parametric approach. The top two programs emerging from this benchmark were MwPharm© and TCIWorks. Most other programs evaluated had good potential while being less sophisticated or less user friendly. Programs vary in complexity and might not fit all healthcare settings. Each software tool must therefore be regarded with respect to the individual needs of hospitals or clinicians. Programs should be easy and fast for routine activities, including for non-experienced users. Computer-assisted TDM is gaining growing interest and should further improve, especially in terms of information system interfacing, user friendliness, data storage capability and report generation.

Guidelines for the use and interpretation of assays for monitoring autophagy in higher eukaryotes.

Research in autophagy continues to accelerate,(1) and as a result many new scientists are entering the field. Accordingly, it is important to establish a standard set of criteria for monitoring macroautophagy in different organisms. Recent reviews have described the range of assays that have been used for this purpose.(2,3) There are many useful and convenient methods that can be used to monitor macroautophagy in yeast, but relatively few in other model systems, and there is much confusion regarding acceptable methods to measure macroautophagy in higher eukaryotes. A key point that needs to be emphasized is that there is a difference between measurements that monitor the numbers of autophagosomes versus those that measure flux through the autophagy pathway; thus, a block in macroautophagy that results in autophagosome accumulation needs to be differentiated from fully functional autophagy that includes delivery to, and degradation within, lysosomes (in most higher eukaryotes) or the vacuole (in plants and fungi). Here, we present a set of guidelines for the selection and interpretation of the methods that can be used by investigators who are attempting to examine macroautophagy and related processes, as well as by reviewers who need to provide realistic and reasonable critiques of papers that investigate these processes. This set of guidelines is not meant to be a formulaic set of rules, because the appropriate assays depend in part on the question being asked and the system being used. In addition, we emphasize that no individual assay is guaranteed to be the most appropriate one in every situation, and we strongly recommend the use of multiple assays to verify an autophagic response.

Detection of methotrexate using surface plasmon resonance biosensors for chemotherapy monitoring

Le méthotrexate (MTX), un agent anti-cancéreux fréquemment utilisé en chimiothérapie, requiert généralement un suivi thérapeutique de la médication (Therapeutic Drug Monitoring, TDM) pour surveiller son niveau sanguin chez le patient afin de maximiser son efficacité tout en limitant ses effets secondaires. Malgré la fenêtre thérapeutique étroite entre l’efficacité et la toxicité, le MTX reste, à ce jour, un des agents anti-cancéreux les plus utilisés au monde. Les techniques analytiques existantes pour le TDM du MTX sont coûteuses, requièrent temps et efforts, sans nécessairement fournir promptement les résultats dans le délai requis. Afin d’accélérer le processus de dosage du MTX en TDM, une stratégie a été proposée basée sur un essai compétitif caractérisé principalement par le couplage plasmonique d’une surface métallique et de nanoparticules d’or. Plus précisément, l’essai quantitatif exploite la réaction de compétition entre le MTX et une nanoparticule d’or fonctionnalisée avec l’acide folique (FA-AuNP) ayant une affinité pour un récepteur moléculaire, la réductase humaine de dihydrofolate (hDHFR), une enzyme associée aux maladies prolifératives. Le MTX libre mixé avec les FA-AuNP, entre en compétition pour les sites de liaison de hDHFR immobilisés sur une surface active en SPR ou libres en solution. Par la suite, les FA-AuNP liées au hDHFR fournissent une amplification du signal qui est inversement proportionnelle à la concentration de MTX. La résonance des plasmons de surface (SPR) est généralement utilisée comme une technique spectroscopique pour l’interrogation des interactions biomoléculaires. Les instruments SPR commerciaux sont généralement retrouvés dans les grands laboratoires d’analyse. Ils sont également encombrants, coûteux et manquent de sélectivité dans les analyses en matrice complexe. De plus, ceux-ci n’ont pas encore démontré de l’adaptabilité en milieu clinique. Par ailleurs, les analyses SPR des petites molécules comme les médicaments n’ont pas été explorés de manière intensive dû au défi posé par le manque de la sensibilité de la technique pour cette classe de molécules. Les développements récents en science des matériaux et chimie de surfaces exploitant l’intégration des nanoparticules d’or pour l’amplification de la réponse SPR et la chimie de surface peptidique ont démontré le potentiel de franchir les limites posées par le manque de sensibilité et l’adsorption non-spécifique pour les analyses directes dans les milieux biologiques. Ces nouveaux concepts de la technologie SPR seront incorporés à un système SPR miniaturisé et compact pour exécuter des analyses rapides, fiables et sensibles pour le suivi du niveau du MTX dans le sérum de patients durant les traitements de chimiothérapie. L’objectif de cette thèse est d’explorer différentes stratégies pour améliorer l’analyse des médicaments dans les milieux complexes par les biocapteurs SPR et de mettre en perspective le potentiel des biocapteurs SPR comme un outil utile pour le TDM dans le laboratoire clinique ou au chevet du patient. Pour atteindre ces objectifs, un essai compétitif colorimétrique basé sur la résonance des plasmons de surface localisée (LSPR) pour le MTX fut établi avec des nanoparticules d’or marquées avec du FA. Ensuite, cet essai compétitif colorimétrique en solution fut adapté à une plateforme SPR. Pour les deux essais développés, la sensibilité, sélectivité, limite de détection, l’optimisation de la gamme dynamique et l’analyse du MTX dans les milieux complexes ont été inspectés. De plus, le prototype de la plateforme SPR miniaturisée fut validé par sa performance équivalente aux systèmes SPR existants ainsi que son utilité pour analyser les échantillons cliniques des patients sous chimiothérapie du MTX. Les concentrations de MTX obtenues par le prototype furent comparées avec des techniques standards, soit un essai immunologique basé sur la polarisation en fluorescence (FPIA) et la chromatographie liquide couplée avec de la spectrométrie de masse en tandem (LC-MS/MS) pour valider l’utilité du prototype comme un outil clinique pour les tests rapides de quantification du MTX. En dernier lieu, le déploiement du prototype à un laboratoire de biochimie dans un hôpital démontre l’énorme potentiel des biocapteurs SPR pour utilisation en milieux clinique.

Characterization of Selected Photonic Materials and Systems Using Photoacoustic Technique

The photoacoustic investigations carried out on different photonic materials are presented in this thesis. Photonic materials selected for the investigation are tape cast ceramics, muItilayer dielectric coatings, organic dye doped PVA films and PMMA matrix doped with dye mixtures. The studies are performed by the measurement of photoacoustic signal generated as a result of modulated cw laser irradiation of samples. The gas-microphone scheme is employed for the detection of photoacoustic signal. The different measurements reported here reveal the adaptability and utility of the PA technique for the characterization of photonic materials.Ceramics find applications in the field of microelectronics industry. Tape cast ceramics are the building blocks of many electronic components and certain ceramic tapes are used as thermal barriers. The thermal parameters of these tapes will not be the same as that of thin films of the same materials. Parameters are influenced by the presence of foreign bodies in the matrix and the sample preparation technique. Measurements are done on ceramic tapes of Zirconia, Zirconia-Alumina combination, barium titanate, barium tin titanate, silicon carbide, lead zirconate titanateil'Z'T) and lead magnesium niobate titanate(PMNPT). Various configurations viz. heat reflection geometry and heat transmission geometry of the photoacoustic technique have been used for the evaluation of different thermal parameters of the sample. Heat reflection geometry of the PA cell has been used for the evaluation of thermal effusivity and heat transmission geometry has been made use of in the evaluation of thermal diffusivity. From the thermal diffusivity and thermal effusivity values, thermal conductivity is also calculated. The calculated values are nearly the same as the values reported for pure materials. This shows the feasibility of photoacoustic technique for the thermal characterization of ceramic tapes.Organic dyes find applications as holographic recording medium and as active media for laser operations. Knowledge of the photochemical stability of the material is essential if it has to be used tor any of these applications. Mixing one dye with another can change the properties of the resulting system. Through careful mixing of the dyes in appropriate proportions and incorporating them in polymer matrices, media of required stability can be prepared. Investigations are carried out on Rhodamine 6GRhodamine B mixture doped PMMA samples. Addition of RhB in small amounts is found to stabilize Rh6G against photodegradation and addition of Rh6G into RhB increases the photosensitivity of the latter. The PA technique has been successfully employed for the monitoring of dye mixture doped PMMA sample. The same technique has been used for the monitoring of photodegradation ofa laser dye, cresyl violet doped polyvinyl alcohol also.Another important application of photoacoustic technique is in nondestructive evaluation of layered samples. Depth profiling capability of PA technique has been used for the non-destructive testing of multilayer dielectric films, which are highly reflecting in the wavelength range selected for investigations. Eventhough calculation of thickness of the film is not possible, number of layers present in the system can be found out using PA technique. The phase plot has clear step like discontinuities, the number of which coincides with the number of layers present in the multilayer stack. This shows the sensitivity of PA signal phase to boundaries in a layered structure. This aspect of PA signal can be utilized in non-destructive depth profiling of reflecting samples and for the identification of defects in layered structures.