Setting the preheating process of electronic ballasts for hot-cathode fluorescent lamps, considering the Rh/Rc ratio

This paper presents a new model for the representation of the electrodes filaments of fluorescent lamps, during their preheating, and an analysis capable to guide the design of the preheating process in electronic ballasts. The main improvement obtained with the lamp model is the accurate theoretical reproduction of the behavior of the Rh/Rc ratio during the preheating process. In addition, using the proposed methodology based on the lamp model, it is possible to set a proper preheating process to the electrodes filaments, without the necessity of exhaustive empirical adjustments in the prototype, reducing time and costs involved in the design of ballasts with preheating capabilities. © 2006 IEEE.

In vivo biological behavior of calcium phosphate cements with different Ca/P ratio

Bioceramics with different Ca/P ratio were prepared from a mechanical mixture of NaPO3, CaCO3, Ca(OH)2 and phosphate buffer solution and implanted in rats subcutaneous tissues. The cements were characterized by Thermo gravimetric analysis (TG-TDA), X-ray diffraction and 31P-NMR. The implant sites were excised after 1, 4 and 16 weeks, fixed, dehydrated, included in paraffin wax for serial cutting and examined under the light transmitted microscope. They were biocompatible and biodegradable when implanted in rat subcutaneous. None of the materials induced ectopic osteogenesis. According to the results, the studied materials seem to be able for manufacturing reabsorbable bone implants.

Measurement of the charge ratio of atmospheric muons with the CMS detector

We present a measurement of the ratio of positive to negative muon fluxes from cosmic ray interactions in the atmosphere, using data collected by the CMS detector both at ground level and in the underground experimental cavern at the CERN LHC. Muons were detected in the momentum range from 5 GeV/. c to 1 TeV/. c. The surface flux ratio is measured to be 1.2766±0.0032(stat.)±0.0032(syst.), independent of the muon momentum, below 100 GeV/. c. This is the most precise measurement to date. At higher momenta the data are consistent with an increase of the charge ratio, in agreement with cosmic ray shower models and compatible with previous measurements by deep-underground experiments. © 2010.

Aerosols monitoring in Rio Claro, Brazil: Using lidar and air pollution analyzers

Brazil has an important role in the biomass burning aerosol activity. During the Dry Season (June-September) of 2009 an aerosol profiling campaign was carried out using a backscattering and Raman lidar system in Rio Claro-SP, Brazil (22°23'S and 47°32'W). The main goal of this campaign was to observe the biomass burning aerosol load due to sugarcane crops and also study the air dispersion conditions, planetary boundary and mixed layer daily evolution. In this paper we aim to present the preliminary results of the influence of this type of aerosol over the city of Rio Claro-SP, Brazil and one case study to evaluate the aerosol profile in a biomass burning episode that occurred in July, 2009. On July 15 an intense burning was observed about 300 m away from the lidar location. Throughout the measurements it was observed that the plumes reached up to 900 m, and that there was a time gap between the plumes. The gas analyzers showed a strong influence of this burning as it was noticed in the measurements of CO, NO x and nephelometer, whereas the PM10 did not have due to this burning, possibly because the particulate was deposited further from the emission source, not being detected by the equipment. © Sociedad Española de Óptica.

Emissions from sugar cane fires in the Central & Western State of São Paulo and aerosol layers over metropolitan São Paulo observed by IPEN's lidar: Is there a connection?

The central and western parts of the State of São Paulo are well-known for vast sugar cane plantations, which during the harvest time are traditionally burnt about 12 hours before manual cutting. This procedure causes the release of large quantities of aerosols and a variety of gases, which can be observed by IPMet's radars, located in Bauru and Presidente Prudente, on days with no or little rain. Depending on the distance of these plumes from the radar, they can be detected up to 5 km amsl or more, and are subsequently being transported by winds to other regions. During the dry winter season of 2008, such plumes, attributed to cane fires, were frequently observed by IPMet's radars and documented in terms of radar reflectivity, time and location during the period 10 th - 21 st July 2008. At the same time, IPEN's Elastic Backscatter Lidar in São Paulo observed layers of aerosols of variable strength and heights above the city. The most significant days, viz. 14 and 15 July 2008 had been selected for calculating backward, as well as forward trajectories, deploying the European Flextra 3.3 Trajectory Model, which was initiated with ECMWF historic data with a 0,25 o×0,25 o grid spacing. The results presented here show an excellent match between the radar-detected sources of the plumes on 11 th July 2008 in the central parts of the State and the observations by IPEN's Lidar over Metropolitan São Paulo on 14 th July 2008, both in terms of forward and backward trajectories, as well as their heights, with a transport duration of approximately 70 hours under the prevailing meteorological conditions. © Sociedad Española de Óptica.

Remote Sensing Detection of atmospheric pollutants using Lidar, Sodar and correlation with air quality data in an industrial area

Optical remote sensing techniques have obvious advantages for monitoring gas and aerosol emissions, since they enable the operation over large distances, far from hostile environments, and fast processing of the measured signal. In this study two remote sensing devices, namely a Lidar (Light Detection and Ranging) for monitoring the vertical profile of backscattered light intensity, and a Sodar (Acoustic Radar, Sound Detection and Ranging) for monitoring the vertical profile of the wind vector were operated during specific periods. The acquired data were processed and compared with data of air quality obtained from ground level monitoring stations, in order to verify the possibility of using the remote sensing techniques to monitor industrial emissions. The campaigns were carried out in the area of the Environmental Research Center (Cepema) of the University of São Paulo, in the city of Cubatão, Brazil, a large industrial site, where numerous different industries are located, including an oil refinery, a steel plant, as well as fertilizer, cement and chemical/petrochemical plants. The local environmental problems caused by the industrial activities are aggravated by the climate and topography of the site, unfavorable to pollutant dispersion. Results of a campaign are presented for a 24- hour period, showing data of a Lidar, an air quality monitoring station and a Sodar. © 2011 SPIE.

Building roof contour extraction from LiDAR data

This paper proposes a method for the automatic extraction of building roof contours from a LiDAR-derived digital surface model (DSM). The method is based on two steps. First, to detect aboveground objects (buildings, trees, etc.), the DSM is segmented through a recursive splitting technique followed by a region merging process. Vectorization and polygonization are used to obtain polyline representations of the detected aboveground objects. Second, building roof contours are identified from among the aboveground objects by optimizing a Markov-random-field-based energy function that embodies roof contour attributes and spatial constraints. Preliminary results have shown that the proposed methodology works properly.

Genetic (co)variance components for ratio of lamb weight to ewe metabolic weight as an indicator of ewe efficiency

Data from a multibreed commercial flock located at Mid-West of Brazil, supported by Programa de Melhoramento Genético de Caprinos e Ovinos de Corte (GENECOC), were used to estimate genetic parameters of traits related to ewe productivity by Average Information Restricted Maximum Likelihood method applied to an animal model. The analyzed traits were litter weight at birth (LWB) and at weaning (LWW), ewe weight at weaning (EW) and ewe production efficiency, estimated by WEE=LWW/EW 0.75. The heritabilities were 0.26±0.05, 0.32±0.06, 0.37±0.03 and 0.10±0.02 for LWB, LWW, EW and WEE, respectively. Significant effects for direct heterosis were observed for LWW and EW. Recombination losses were important for EW and WEE. Genetic correlations of LWB with LWW, EW and WEE were 0.68, 0.37 and 0.15, respectively; of LWW with EW and WEE were 0.30 and 0.34, respectively; and between EW and WEE was -0.25. Even though it is a low heritability trait, WEE can be indicated as a selection criteria for improving the ewe productivity without increasing the mature weight of animals due to its genetic correlations with LWW and other traits. © 2011 Elsevier B.V.

Sex ratio, growth and recruitment of the pelagic shrimp Acetes americanus on the southeastern coast of Brazil

We evaluated the population dynamics of Acetes americanus Ortmann, 1893 focusing on sex ratio, individual growth, longevity, and the juvenile recruitment period. Samples were collected monthly from January 2006 to June 2007 in the bay of Ubatuba, Brazil. Specimen growth was identified for each gender, and the chosen cohorts were fitted in a von Bertalanffy Growth Model (VBGM); longevity was estimated by the von Bertalanffy inverse equation, considering 99% of the asymptotic length. A total of 6881 individuals (2343 males and 4538 females) were captured. On average the body size (total length) was greater in females (14.64 ± 3.34 mm) than in males (12.27 ± 1.86 mm). The mean growth curves (obtained by grouping the cohorts for each sex), provided estimates of TL∞ = 19.33 mm, k = 0.02 and t0 = -0.12 days for females and TL∞ = 15.13 mm, k = 0.03 and to = -0.07 days for males, where TL∞ is the asymptotic length, k is coefficient of growth and to is the theorical age when the size is equal to 0. Longevity was estimated at 0.61 years for females and 0.50 years for males. The sex ratio tended to favor females, which corroborates with others studies of sergestids. Our finding that males of A. americanus have higher values of k and therefore achieve a smaller size relative to females has been observed in other penaeids. We concluded that this differential growth pattern between the sexes is found across Dendrobranchiata. The life cycles of penaeids have an average duration of approximately 1-2 years, but our results corroborate other studies that estimate a shorter longevity for Acetes, as species of this genus are typically smaller in size. We found continuous recruitment with two main peaks observed during the study period, corroborating previous studies of Acetes. © The Crustacean Society, 2013. Published by Brill NV, Leiden.

Alkali activated materials based on fluid catalytic cracking catalyst residue (FCC): Influence of SiO2/Na2O and H 2O/FCC ratio on mechanical strength and microstructure

Reuse of industrial and agricultural wastes as supplementary cementitious materials (SCMs) in concrete and mortar productions contribute to sustainable development. In this context, fluid catalytic cracking catalyst residue (spent FCC), a byproduct from the petroleum industry and petrol refineries, have been studied as SCM in blended Portland cement in the last years. Nevertheless, another environmental friendly alternative has been conducted in order to produce alternative binders with low CO2 emissions. The use of aluminosilicate materials in the production of alkali-activated materials (AAMs) is an ongoing research topic which can present low CO2 emissions associated. Hence, this paper studies some variables that can influence the production of AAM based on spent FCC. Specifically, the influence of SiO 2/Na2O molar ratio and the H2O/spent FCC mass ratio on the mechanical strength and microstructure are assessed. Some instrumental techniques, such as SEM, XRD, pH and electrical conductivity measurements, and MIP are performed in order to assess the microstructure of formed alkali-activated binder. Alkali activated mortars with compressive strength up to 80 MPa can be formed after curing for 3 days at 65°C. The research demonstrates the potential of spent FCC to produce alkali-activated cements and the importance of SiO2/Na2O molar ratio and the H2O/spent FCC mass ratio in optimising properties and microstructure. © 2013 Elsevier Ltd. All rights reserved.

Morphology, sex ratio and gene expression of Day 14 in vivo and in vitro bovine embryos

The present study was designed to compare Day 14 bovine embryos that were produced entirely in vitro using the post-hatching development (PHD) system with in vivo-derived embryos without or with transient PHD culture from Day 7 to Day 14. Embryos on Day 14 were used for sex determination and gene expression analysis of PLAC8, KRT8, CD9, SLC2A1, SLC2A3, PGK1, HSF1, MNSOD, HSP70 and IFNT using real-time quantitative (q) polymerase chain reaction (PCR). First, Day 7 in vivo-and in vitro-produced embryos were subjected to the PHD system. A higher rate of survival was observed for in vitro embryos on Day 14. Comparing Day 14 embryos produced completely in vivo or completely in vitro revealed that the mean size of the former group was greater than that of the latter (10.29±1.83 vs 2.68±0.33mm, respectively). Expression of the HSP70 and SLC2A1 genes was down-and upregulated, respectively, in the in vitro embryos. The present study shows that in vitro embryos cultured in the PHD system are smaller than in vivo embryos and that of the 10 genes analysed, only two were differentially expressed between the two groups. These findings indicate that, owing to the poor survival rate, the PHD system is not reliable for evaluation of in vitro embryo quality. © 2013 CSIRO.

Digit ratio (2D:4D) is associated with gastric cancer

Background: Sex steroid exposure during early human development may influence disease susceptibility. Digit ratio (2D:4D) is a putative marker for prenatal hormone exposure and sensitivity, as well as the action of genes closely related to carcinogenesis. Digit ratio could act as a possible marker for cancer predisposition. Aims: The aim of this study is to investigate the possible correlations between right hand, left hand and right minus left (R. - L) 2D:4D and gastric cancer (GCA) in men and women and assess the correlations with tumor staging and histological diagnosis. Methods: Digital images of the right and left hand palms of patients diagnosed with GCA (n = 57, 42 males, 15 females) and age and sex-matched controls (n = 59, 41 males, 18 females) were obtained. Means for 2D:4D were compared. Data were analyzed by repeated-measures one-way ANOVA and Student's t-test for finger measurements and group comparisons and Pearson's and Spearman's tests for correlations with tumor staging (α = 0.05). Results: GCA group presented significantly higher left 2D:4D, but significantly lower R. - L in comparison to healthy controls, particularly so for males. Digit ratio did not correlate to clinical staging or TNM staging. However, low R. - L was significantly related to adenocarcinomas. Conclusions: Early developmental conditions, including prenatal testosterone seem to play a role on the malignant transformation of gastric lesions. The 2D:4D pattern found for gastric cancer parallels that earlier described for breast cancer. The findings suggest that 2D:4D could add to the list of etiological factors and be a putative marker for the screening of patients' susceptibility to develop gastric cancer. © 2012 Elsevier Ltd.

SFlt-1/PlGF ratio as a prognostic marker of adverse outcomes in women with early-onset preeclampsia

Soluble fms-like tyrosine kinase 1 (sFlt-1) is an anti-angiogenic factor released in higher amounts by preeclamptic placentas and it has been implicated in the endothelial dysfunction observed in the disease. In this study we evaluated if circulating sFlt-1/PlGF ratio is useful to predict adverse outcomes in women with early-onset preeclampsia. This is a cohort study of 88 preeclamptic women with singleton pregnancies at ≤35 weeks of gestation. According to definitions used, adverse outcomes occurred in 46.5% (N = 43) of the patients. The median sFlt1/PlGF ratio (25th-75th centile) for all patients evaluated was of 42.26 (13.1-226.1). The median sFlt-1/PlGF ratio among women who had any adverse outcome (N = 43) versus no adverse outcomes (N = 45) was of 227.6 (80.3-346.1) versus 14.4 (3.35-30.0), (P < 0.0001). According to our analyses a sFlt-1/PlGF ratio cut-point of ≥85 gave a sensitivity of 74.0% and specificity of 97.0%. The positive predictive value and the negative predictive value were 96.0% and 80.0%, respectively. The median sFlt-1/PlGF ratio (25th-75th centile) for patients who delivered within <7 days was 260.0 (127.7-404.7) as compared to 14.4 (3.35-34.97) for those patients who delivered within two weeks or more (P < 0.0001). Our results suggest that sFlt-1/PlGF ratio is a promising marker for adverse outcomes in women with early-onset preeclampsia. © 2013 International Society for the Study of Hypertension in Pregnancy. Published by Elsevier B.V. All rights reserved.

Simulated annealing for building roof contours identification from lidar data

This paper proposes a method by simulated annealing for building roof contours identification from LiDAR-derived digital elevation model. Our method is based on the concept of first extracting aboveground objects and then identifying those objects that are building roof contours. First, to detect aboveground objects (buildings, trees, etc.), the digital elevation model is segmented through a recursive splitting technique followed by a region merging process. Vectorization and polygonization are used to obtain polyline representations of the detected aboveground objects. Second, building roof contours are identified from among the aboveground objects by optimizing a Markov-random-field-based energy function that embodies roof contour attributes and spatial constraints. The solution of this function is a polygon set corresponding to building roof contours and is found by using a minimization technique, like the Simulated Annealing algorithm. Experiments carried out with laser scanning digital elevation model showed that the methodology works properly, as it provides roof contour information with approximately 90% shape accuracy and no verified false positives.

Bovine herpesvirus type 5 infection regulates Bax/BCL-2 ratio

Bovine herpesvirus 5 (BoHV-5) is an α-herpesvirus that causes neurological disease in young cattle and is also occasionally involved in reproductive disorders. Although there have been many studies of the apoptotic pathways induced by viruses belonging to the family Herpesviridae, there is little information about the intrinsic programmed cell death pathway in host-BoHV-5 interactions. We found that BoHV-5 is able to replicate in both mesenchymal and epithelial cell lines, provoking cytopathology that is characterized by cellular swelling and cell fusion. Viral antigens were detected in infected cells by immunofluorescence assay at 48 to 96 h post-infection (p.i.). At 48 to 72 h p.i., anti-apoptotic BCL-2 antigens were found at higher levels than Bax antigens; the latter is considered a pro-apoptotic protein. Infected cells had increased BCL-2 phenotype cells from 48 to 96 h p.i., based on flow cytometric analysis. At 48 to 96 h p.i., Bax mRNA was not expressed in any of the infected cell monolayers. In contrast, BCL-2 mRNA was found at high levels at all p.i. in both types of cells. BoHV-5 replication apparently modulates BCL-2 expression and gene transcription, enhancing production of virus progeny. © FUNPEC-RP.