Comparison of the efficacy of biodegradable and non-biodegradable scintillation liquids on the counting of tritium- and [14C]-labeled compounds

The widespread use of ³H and 14C in research has generated a large volume of waste mixed with scintillation liquid, requiring an effective control and appropriate storage of liquid radioactive waste. In the present study, we compared the efficacy of three commercially available scintillation liquids, Optiphase HiSafe 3, Ultima-Gold™ AB (biodegradable) and Insta-Gel-XF (non-biodegradable), in terms of [14C]-glucose and [³H]-thymidine counting efficiency. We also analyzed the effect of the relative amount of water (1.6 to 50%), radioisotope concentration (0.1 to 100 nCi/ml), pH (2 to 10) and color of the solutions (samples containing 0.1 to 1.0 mg/ml of Trypan blue) on the counting efficiency in the presence of these scintillation liquids. There were few significant differences in the efficiency of 14C and ³H counting obtained with biodegradable or non-biodegradable scintillation liquids. However, there was an 83 and 94% reduction in the efficiency of 14C and ³H counting, respectively, in samples colored with 1 mg/ml Trypan blue, but not with 0.1 mg/ml, independent of the scintillation liquid used. Considering the low cost of biodegradable scintillation cocktails and their efficacy, these results show that traditional hazardous scintillation fluids may be replaced with the new safe biodegradable fluids without impairment of ³H and 14C counting efficiency. The use of biodegradable scintillation cocktails minimizes both human and environmental exposure to hazardous solvents. In addition, some biodegradable scintillation liquids can be 40% less expensive than the traditional hazardous cocktails.

Aurapten, a coumarin with growth inhibition against Leishmania major promastigotes

Several natural compounds have been identified for the treatment of leishmaniasis. Among them are some alkaloids, chalcones, lactones, tetralones, and saponins. The new compound reported here, 7-geranyloxycoumarin, called aurapten, belongs to the chemical class of the coumarins and has a molecular weight of 298.37. The compund was extracted from the Rutaceae species Esenbeckia febrifuga and was purified from a hexane extract starting from 407.7 g of dried leaves and followed by four silica gel chromatographic fractionation steps using different solvents as the mobile phase. The resulting compound (47 mg) of shows significant growth inhibition with an LD50 of 30 µM against the tropical parasite Leishmania major, which causes severe clinical manifestations in humans and is endemic in the tropical and subtropical regions. In the present study, we investigated the atomic structure of aurapten in order to determine the existence of common structural motifs that might be related to other coumarins and potentially to other identified inhibitors of Leishmania growth and viability. This compound has a comparable inhibitory activity of other isolated molecules. The aurapten is a planar molecule constituted of an aromatic system with electron delocalization. A hydrophobic side chain consisting of ten carbon atoms with two double bonds and negative density has been identified and may be relevant for further compound synthesis.

Stability and properties of cellulose-sodium hydroxide solution systems

Since cellulose is a linear macromolecule it can be used as a material for regenerated cellulose fiber products e.g. in textile fibers or film manufacturing. Cellulose is not thermoformable, thus the manufacturing of these regenerated fibers is mainly possible through dissolution processes preceding the regeneration process. However, the dissolution of cellulose in common solvents is hindered due to inter- and intra-molecular hydrogen bonds in the cellulose chains, and relatively high crystallinity. Interestingly at subzero temperatures relatively dilute sodium hydroxide solutions can be used to dissolve cellulose to a certain extent. The objective of this work was to investigate the possible factors that govern the solubility of cellulose in aqueous NaOH and the solution stability. Cellulose-NaOH solutions have the tendency to form a gel over time and at elevated temperature, which creates challenges for further processing. The main target of this work was to achieve high solubility of cellulose in aqueous NaOH without excessively compromising the solution stability. In the literature survey an overview of the cellulose dissolution is given and possible factors contributing to the solubility and solution properties of cellulose in aqueous NaOH are reviewed. Furthermore, the concept of solution rheology is discussed. In the experimental part the focus was on the characterization of the used materials and properties of the prepared solutions mainly concentrating on cellulose solubility and solution stability.

Multigenerational Brazilian family with malignant hyperthermia and a novel mutation in the RYR1 gene

Malignant hyperthermia (MH) is a pharmacogenetic disease triggered in susceptible individuals by the administration of volatile halogenated anesthetics and/or succinylcholine, leading to the development of a hypermetabolic crisis, which is caused by abnormal release of Ca2+ from the sarcoplasmic reticulum, through the Ca2+ release channel ryanodine receptor 1 (RyR1). Mutations in the RYR1 gene are associated with MH in the majority of susceptible families. Genetic screening of a 5-generation Brazilian family with a history of MH-related deaths and a previous MH diagnosis by the caffeine halothane contracture test (CHCT) in some individuals was performed using restriction and sequencing analysis. A novel missense mutation, Gly4935Ser, was found in an important functional and conserved locus of this gene, the transmembrane region of RyR1. In this family, 2 MH-susceptible individuals previously diagnosed with CHCT carry this novel mutation and another 24 not previously diagnosed members also carry it. However, this same mutation was not found in another MH-susceptible individual whose CHCT was positive to the test with caffeine but not to the test with halothane. None of the 5 MH normal individuals of the family, previously diagnosed by CHCT, carry this mutation, nor do 100 controls from control Brazilian and USA populations. The Gly4932Ser variant is a candidate mutation for MH, based on its co-segregation with disease phenotype, absence among controls and its location within the protein.

Polymorphism of the aryl-hydrocarbon receptor gene in intron 10 of human cancers

Polychlorinated dibenzo-p-dioxins (PCDDs) and related halogenated aromatic hydrocarbons (e.g., PCDFs), often called "dioxins", are ubiquitously present environmental contaminants. Some of them, notably 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD), are among the most toxic synthetic compounds known. The biological effects of dioxins are mediated via the aryl hydrocarbon receptor (AhR). Mutations in the AhR transactivation domain are linked to sensitivity to the acute lethality of TCDD. We present here a study of AhR gene polymorphism in normal and cancer human tissues affecting pre-mRNA splicing in the AhR gene-coding transactivation domain region (exon 10, intron 10, exon 11 region), previously shown to be associated with AhR dysfunction. We tested 126 pairs of normal and cancer tissue samples from liver, lung, stomach, kidney, mucous, breast, and pancreas of 49 males and 77 females (45-70 years of age). We used in vitro splicing assay, RT-PCR and sequencing methods. Our results showed that in an in vitro system it is possible to reconstitute cellular pre-mRNA splicing events. Tested cancer tissues did not contain mutations in the AhR transactivation domain region when the DNA sequences were compared with those from normal tissues. There were also no differences in AhR mRNA splice variants between normal and malignant breast tissues and no polymorphisms in the studied regions or cDNA.

Enhanced production and organic solvent stability of a protease fromBrevibacillus laterosporus strain PAP04

A bacterial strain (PAP04) isolated from cattle farm soil was shown to produce an extracellular, solvent-stable protease. Sequence analysis using 16S rRNA showed that this strain was highly homologous (99%) to Brevibacillus laterosporus. Growth conditions that optimize protease production in this strain were determined as maltose (carbon source), skim milk (nitrogen source), pH 7.0, 40°C temperature, and 48 h incubation. Overall, conditions were optimized to yield a 5.91-fold higher production of protease compared to standard conditions. Furthermore, the stability of the enzyme in organic solvents was assessed by incubation for 2 weeks in solutions containing 50% concentration of various organic solvents. The enzyme retained activity in all tested solvents except ethanol; however, the protease activity was stimulated in benzene (74%) followed by acetone (63%) and chloroform (54.8%). In addition, the plate assay and zymography results also confirmed the stability of the PAP04 protease in various organic solvents. The organic solvent stability of this protease at high (50%) concentrations of solvents makes it an alternative catalyst for peptide synthesis in non-aqueous media.

STATISTICAL ANALYSYS OF THE SCFE OF A BRAZILAN MINERAL COAL

The influence of some process variables on the productivity of the fractions (liquid yield times fraction percent) obtained from SCFE of a Brazilian mineral coal using isopropanol and ethanol as primary solvents is analyzed using statistical techniques. A full factorial 23 experimental design was adopted to investigate the effects of process variables (temperature, pressure and cosolvent concentration) on the extraction products. The extracts were analyzed by the Preparative Liquid Chromatography-8 fractions method (PLC-8), a reliable, non destructive solvent fractionation method, especially developed for coal-derived liquids. Empirical statistical modeling was carried out in order to reproduce the experimental data. Correlations obtained were always greater than 0.98. Four specific process criteria were used to allow process optimization. Results obtained show that it is not possible to maximize both extract productivity and purity (through the minimization of heavy fraction content) simultaneously by manipulating the mentioned process variables.

Processing of spent nickelcatalyst for fat recovery

Spent nickel catalyst (SNC) has the potential of insulting the quality of the environment in a number of ways. Its disposal has a pollution effect. Optimum recovery of fat from SNC, could save the environment and reduce the oil loss. Hexane has been the solvent of choice for oil extraction. Alternative solvents considered to have been safer have been evaluated. Hexane, isopropanol, ethanol and heptane were examined using soxhlet extraction. While hexane is more efficient in oil recovery from SNC, isopropanol proved to be very good in clear separation of oil from waste material and also provides high solvent recovery compared to other solvents. Isopropanol extraction with chill separation of miscella into lower oil-rich phase, and an upper, solvent-rich recyclable phase save mush energy of vaporization for distilling. An aqueous extraction process with immiscible solvent assisted was tested. Solvent like hexane added to SNC, and water added later with continuous stirring. The mixture was stirred for about 30 minutes, prior to centrifugation. Aqueous process extracted less amount of oil compared to solvent extraction.

Influence of the extraction method and storage time on the physicochemical properties and carotenoid levels of pequi (Caryocar brasiliense Camb.) oil

The objective of this study was to analyze the physicochemical properties and carotenoid levels of pequi oil obtained by different extraction methods and to evaluate the preservation of these properties and pigments during storage time. The pequi oil was obtained by solvent extraction, mechanical extraction, and hot water flotation. It was stored for over 180 days in an amber bottle at ambient conditions. Analyses for the determination of the acidity, peroxide, saponification and iodine values, coloration, total carotenoids, and β-carotene levels were conducted. The oil extraction with solvents produced the best yield and carotenoid levels. The oil obtained by mechanical extraction presented higher acidity (5.44 mg KOH.g-1) and peroxide values (1.07 mEq.kg-1). During the storage of pequi oil, there was an increase in the acidity and the peroxide values, darkening of the oil coloration, and a reduction of the carotenoid levels. Mechanical extraction is the less advantageous method for the conservation of the physicochemical properties and carotenoid levels in pequi oil.

Antioxidant activity and prevention of pork meat lipid oxidation using traditional Mexican condiments (pasilla dry pepper, achiote, and mole sauce)

Considering the extensive use of hot peppers and spicy sauces in the Mexican cuisine, in the present paper, three widely consumed Mexican condiments (mole sauce, achiote, and pasilla hot pepper) were analyzed for their total phenols, flavonoids and proanthocyanidins, antioxidant activity, and protective effect against lipid oxidation in chopped pork meat. All samples were extracted first with methanol and then with acetone, and the extracts were compared. Pasilla pepper showed the highest phenolic and flavonoid content in both solvents, followed by mole and achiote. Achiote showed the highest proanthocyanidin concentration. All samples showed high antioxidant activity, and good correlations with phenolic compounds and flavonoids, while no correlation was observed in the case of condensed tannins. Mole sauce methanolic extract showed the highest inhibition of pork meat oxidation, followed by pasilla pepper, and finally achiote paste extracts. These results suggest that these condiments are useful to prevent meat lipid oxidation during storage.

Physicochemical properties and antioxidant activity of Tunisian date palm (Phoenix dactylifera L.) oil as affected by different extraction methods

The chemical analysis of flesh and seed of date palm fruit (Kentichi) was evaluated. Carbohydrates were the predominant component in all studied date cultivars (~78.69-83.46 g/100g dry matter), followed by moisture content (~9.23-11.17%), along with moderate amount of fat (~0.56-7.10 g/100g dry matter), protein (~2.16-2.80 g/100g dry matter), and ash (~1.18-1.64 g/100 g dry matter). Some antioxidants (Ascorbic acid, total phenolic, total flavonoid, chlorophyll and carotenoids) were found in different values in both date fruit and seed. The physicochemical properties and antioxidant activity of both flesh and seed oil which was extracted using Hexane, Soxhlet and Modified Bligh - Dyer extraction methods were determined. The experimental results showed that temperature, different solvents and extraction time had significant effect on the yield of the date palm oil and physicochemical properties. Date Flesh oil showed an important free radical scavenging activity towards 1-1-diphenyl-2-picrylhydrazyl (DPPH) free radical.

Chemical composition and antioxidant activity of jatobá-do-cerrado (Hymenaea stigonocarpa Mart.) flour

The Brazilian Savannah, known as "Cerrado," has an extensive biodiversity, but it is under explored. Among the native vegetables is the jatobá-do-cerrado (Hymenaea stigonocarpa Mart.), a legume with great potential for exploration for its content of dietary fiber. Legumes are an important source of nutrient compounds, such as phenolic compounds and vitamins that have antioxidant properties. This study aimed at determining the chemical composition and antioxidant activity of the jatobá flour. The jatobá flour showed high fiber content (insoluble and soluble fiber 47.8 and 12.8 g.100 g- 1, respectively), significant amounts of carotenoids such as beta-carotene and lutein, and some minerals such as calcium: 145 mg.100 g- 1, magnesium: 125 mg.100 g- 1, and potassium: 1352 mg.100 g- 1. The jatobá flour extracted with different solvents (water, methanol, and acetone) exhibited antioxidant activity by the DPPH, FRAP, and ORAC methods. The solvent used in the extraction affected the total phenolic content and antioxidant activity. Acetone extraction produced the best results. Therefore, the jatobá flour is an ingredient that can be used to develop new products with properties that promote health.

Production, solubility and antioxidant activity of curcumin nanosuspension

Curcumin is a powerful bioactive agent and natural antioxidant, but it is practically water-insoluble and has low bioavailability; a possible solution to this obstacle would be formulations of curcumin nanoparticles. Surfactants such as tween 80 can be used to stabilize low-solubility molecules preventing particle aggregation. The objectives of this study were the preparation of a suspension with curcumin nanoparticles in tween 80, the testing of pure curcumin solubility and of a simple mixture of curcumin with tween 80 and nanosuspension in water and ethanol as solvents, and finally the assessment of the antioxidant activity. We prepared the nanosuspension by injecting a curcumin solution in dichloromethane at low flow in water with tween 80 under heating and ultrasound. The analysis of particles size was conducted through dynamic light scattering; the non-degradation of curcumin was verified through thin-layer chromatography. The analyses of antioxidant activity were carried out according to the DPPH method. The method applied to reduce the particles size was efficient. Both the curcumin suspension and nanosuspension in tween 80 increased its solubility. Curcumin and the formulations presented antioxidant activity.

Physicochemical and antioxidative properties of black, brown and red rice varieties of northern Thailand

Rice, the seed of Oryza species, is the major cereal crop in most of the developing countries. Nearly 95% of global rice production is done in Asian countries, and about half of the world’s population consumes it. Some speciality rices are not commonly consumed. Colored rice is one of such variety. In these varieties, high amounts of anthocyanin pigment are deposited in the rice coat to form its black (also known as purple), brown and red colors. Minimum studies are there to explain the properties of these rice varieties of Thailand. Thus, the current study was aimed to assess the physicochemical and antioxidative properties of three rice varieties (Chiang Mai Black rice, Mali Red rice and Suphanburi-1 Brown rice) of different cultivars of northern Thailand. Rice bran extracts of these three cultivars were prepared with different solvents (polar and non-polar) for the evaluation of total phytochemical content and anti-oxidant free-radical-scavenging properties. Chiang Mai Black rice contained higher concentration of phenolic acid, flavonoids, and anthocyanins (Cyanidin 3-glucoside, peonidin 3-glucoside, cyanidin chloride). Chiang Mai Black rice is richer in free-radical-scavenging compounds and activities than the other tested varieties. Polar extractions of rice bran are high in anti-oxidative compounds and activities than non-polar extractions.

Optimization of the extraction process of polyphenols from cashew apple agro-industrial residues

The goal of this study was to determine the chemical composition of cashew apples agro-industrial residue and optimize the process of polyphenols extraction in this residue. The extraction process conditions were defined using a 24-1 fractional factorial experimental design using acetone and methanol as solvents. The independent variables were: time (30 to 90 min), temperature (30 to 50 °C), solvent concentrations (50% to 90%), agitation speed (100 to 300 rpm); the dependent variables were: total phenolic content and DPPH scavenging capacity. The optimized process was carried out by applying the Central Composite Rotational Design (CCRD) considering the results obtained with the 24-1 fractional factorial experimental design. The residue presented bioactive compounds in its composition, with emphasis on the content of total phenolic compounds (1975.64 mg/ 100 g). The extraction process was not affected by methanol; however, acetone affected the amounts of extracted phytochemicals. Extracts with high levels of polyphenols and strong DPPH scavenging capacity (> 80%) were obtained using 55% acetone, 30 minutes, 30 °C, and 150 rpm. The results showed that cashew apple residue is a potential natural source of bioactive compounds with strong antioxidant capacity. These compounds could be used partially or totally to replace synthetic antioxidants.