A III-V channel field effect transistor for non-classical CMOS: process optimisation for improved gate stack function

This thesis describes a collection of studies into the electrical response of a III-V MOS stack comprising metal/GaGdO/GaAs layers as a function of fabrication process variables and the findings of those studies. As a result of this work, areas of improvement in the gate process module of a III-V heterostructure MOSFET were identified. Compared to traditional bulk silicon MOSFET design, one featuring a III-V channel heterostructure with a high-dielectric-constant oxide as the gate insulator provides numerous benefits, for example: the insulator can be made thicker for the same capacitance, the operating voltage can be made lower for the same current output, and improved output characteristics can be achieved without reducing the channel length further. It is known that transistors composed of III-V materials are most susceptible to damage induced by radiation and plasma processing. These devices utilise sub-10 nm gate dielectric films, which are prone to contamination, degradation and damage. Therefore, throughout the course of this work, process damage and contamination issues, as well as various techniques to mitigate or prevent those have been investigated through comparative studies of III-V MOS capacitors and transistors comprising various forms of metal gates, various thicknesses of GaGdO dielectric, and a number of GaAs-based semiconductor layer structures. Transistors which were fabricated before this work commenced, showed problems with threshold voltage control. Specifically, MOSFETs designed for normally-off (VTH > 0) operation exhibited below-zero threshold voltages. With the results obtained during this work, it was possible to gain an understanding of why the transistor threshold voltage shifts as the gate length decreases and of what pulls the threshold voltage downwards preventing normally-off device operation. Two main culprits for the negative VTH shift were found. The first was radiation damage induced by the gate metal deposition process, which can be prevented by slowing down the deposition rate. The second was the layer of gold added on top of platinum in the gate metal stack which reduces the effective work function of the whole gate due to its electronegativity properties. Since the device was designed for a platinum-only gate, this could explain the below zero VTH. This could be prevented either by using a platinum-only gate, or by matching the layer structure design and the actual gate metal used for the future devices. Post-metallisation thermal anneal was shown to mitigate both these effects. However, if post-metallisation annealing is used, care should be taken to ensure it is performed before the ohmic contacts are formed as the thermal treatment was shown to degrade the source/drain contacts. In addition, the programme of studies this thesis describes, also found that if the gate contact is deposited before the source/drain contacts, it causes a shift in threshold voltage towards negative values as the gate length decreases, because the ohmic contact anneal process affects the properties of the underlying material differently depending on whether it is covered with the gate metal or not. In terms of surface contamination; this work found that it causes device-to-device parameter variation, and a plasma clean is therefore essential. This work also demonstrated that the parasitic capacitances in the system, namely the contact periphery dependent gate-ohmic capacitance, plays a significant role in the total gate capacitance. This is true to such an extent that reducing the distance between the gate and the source/drain ohmic contacts in the device would help with shifting the threshold voltages closely towards the designed values. The findings made available by the collection of experiments performed for this work have two major applications. Firstly, these findings provide useful data in the study of the possible phenomena taking place inside the metal/GaGdO/GaAs layers and interfaces as the result of chemical processes applied to it. In addition, these findings allow recommendations as to how to best approach fabrication of devices utilising these layers.

Quantum Gate and Quantum State Preparation through Neighboring Optimal Control

Successful implementation of fault-tolerant quantum computation on a system of qubits places severe demands on the hardware used to control the many-qubit state. It is known that an accuracy threshold Pa exists for any quantum gate that is to be used for such a computation to be able to continue for an unlimited number of steps. Specifically, the error probability Pe for such a gate must fall below the accuracy threshold: Pe < Pa. Estimates of Pa vary widely, though Pa ∼ 10−4 has emerged as a challenging target for hardware designers. I present a theoretical framework based on neighboring optimal control that takes as input a good quantum gate and returns a new gate with better performance. I illustrate this approach by applying it to a universal set of quantum gates produced using non-adiabatic rapid passage. Performance improvements are substantial comparing to the original (unimproved) gates, both for ideal and non-ideal controls. Under suitable conditions detailed below, all gate error probabilities fall by 1 to 4 orders of magnitude below the target threshold of 10−4. After applying the neighboring optimal control theory to improve the performance of quantum gates in a universal set, I further apply the general control theory in a two-step procedure for fault-tolerant logical state preparation, and I illustrate this procedure by preparing a logical Bell state fault-tolerantly. The two-step preparation procedure is as follow: Step 1 provides a one-shot procedure using neighboring optimal control theory to prepare a physical qubit state which is a high-fidelity approximation to the Bell state |β01⟩ = 1/√2(|01⟩ + |10⟩). I show that for ideal (non-ideal) control, an approximate |β01⟩ state could be prepared with error probability ϵ ∼ 10−6 (10−5) with one-shot local operations. Step 2 then takes a block of p pairs of physical qubits, each prepared in |β01⟩ state using Step 1, and fault-tolerantly prepares the logical Bell state for the C4 quantum error detection code.

Playgrounds going wrong: study of the adult style and children's rights during recess in an early childhood and primary education center

Recent perspectives on Pedagogy for Early Childhood Education emphasize children's participation in line with the Children's Rights Convention. The study aimed to analyse how children's rights are dealt with during recess in a school (Early Childhood and Primary Education) in Portugal. The aims were: to characterize the style of the adult (teaching assistants) and the interactions that are established with the children at the playground/recess, and analyse them in terms of children's rights. The qualitative approach was based on the observation during the recess for three weeks. The Adult Style Observation Schedule for Early Childhood Education (ASOS-ECE) was used to register and code the dynamics of six teaching assistants (3 ECE and 3 PE). Critical incidents were also registered. Statistical analysis of the ASOS-ECE levels were complemented with the content analysis of the notes. The playground space was quite limited and affected children's play and well-being. The outdoor playground was never used for the Early Childhood classes, only for Primary Education students but with little supervision. Children were often deprived of playground time by decision of the teaching assistants, as punishment. The results obtained through the Adult Style Observation Schedule for Early Childhood Education (ASOS-ECE) are not satisfactory and are below what would meet the minimum quality value (3,5). For Early Childhood Education, sensibility is the most valued dimension but with very low levels (<2,5). For Primary Education it was autonomy that scored highest (<2,5). The analysis of the notes/critical incidents highlighted articles 12 (expression of own views), 13 (freedom of expression), 19 (protection against violence), 29 (development of personality) and 31 (rest and leisure, play and recreational activities) as being put into question by actions of the adults responsible for the children. Children's rights and well-being need to be put forward in the knowledge base for all adults working with children so that Pedagogy can fulfil its purpose fully.

When the virtual influences reality. The conservation project of the toledo gate in ciudad real (Spain)

The Toledo Gate of Ciudad Real, Spain, constructed between the late 13th and early 14th centuries, is the last remaining portion of a once complete medieval city wall. It represents the long history of the city and constitutes its main heritage symbol, dividing the historic city centre from the later 19th and 20th century expansions. In October 2012, the Town Hall and the Montemadrid Foundation started the conservation works to preserve this important monument. The preliminary phase of this project included an in-depth series of scientific studies which were carried out by a multidisciplinary team focusing on archival research, historic investigations, archaeological excavations as well as material composition analysis and main treatment application tests. As a result of these studies a series of virtual 3D models were created to inform, discuss and study the monument. A first digital model permitted visualization of the gate in the 19th century and how the main entrance to the city was integrated as a fundamental part of the city walls. This virtual reconstruction also became an important part of the campaign to raise awareness among the citizens towards a monument that had remained in the shadows for the last century, isolated in a roundabout after the systematic demolition of the city walls in the late 19th century. Over the last three years and as a result of these archaeological and historic investigations and subsequent virtual models, surprisingly new and interesting data were brought to light thus permitting the establishment and corroboration of a new and updated hypothesis of the Toledo Gate that goes beyond the previous ideas. As a result of these studies a new architectural typology with construction techniques of has been suggested. This paper describes how the results of this continuous and interdisciplinary documentation process have benefitted from a computer graphic reconstruction of the gate. It highlights how virtual reconstruction can be a powerful tool for conservation decision making and awareness raising. Furthermore, the interesting results of the final reconstruction hypothesis convinced the technical team responsible for the conservation to alter some aspects of the final project physical interventions in order to focus on some of the features and conclusions discovered through the virtual model study.

Social competence at the playground: Preschoolers during recess

Social interactions at the playground have been represented as a rich learning opportunity to hone and master social skills at pre- school years. Specifically, all forms of social play (fantasy, role, ex- ercise or rough-and-tumble) have been related to children’s social competence. The main goal of this study was to examine whether it is a certain kind of social play which facilitates the development of social competence, or if it is just the opportunity for interacting during recess that provides children with an optimal environment for social learning. A total of 73 preschoolers (4–6 years old) were videotaped at the school’s playground. Teachers provided assess- ments of children’s social competence. Children’s interactions at the playground were assessed through an innovative measuring method, based on radio-frequency identification devices. The results showed a positive association between exercise play and children’s social competence. In contrast with the literature, both forms of pretend play, fantasy and role play were unrelated to children’s social competence. Smaller peer groups and longer interactions also demonstrated a positive association with these preschoolers’ social competence. The study shows the importance of outdoor physical play for preschoolers’ social success. More- over, the study suggests that the environment in which children play has an important effect on the adaptive nature of their play.

Social competence at the playground: Preschoolers during recess

Social interactions at the playground have been represented as a rich learning opportunity to hone and master social skills at preschool years. Specifically, all forms of social play (fantasy, role, exercise or rough-and-tumble) have been related to children’s social competence. The main goal of this study was to examine whether it is a certain kind of social play which facilitates the development of social competence, or if it is just the opportunity for interacting during recess that provides children with an optimal environment for social learning. A total of 73 preschoolers (4–6 years old) were videotaped at the school’s playground. Teachers provided assessments of children’s social competence. Children’s interactions at the playground were assessed through an innovative measuring method, based on radio-frequency identification devices. The results showed a positive association between exercise play and children’s social competence. In contrast with the literature, both forms of pretend play, fantasy and role play were unrelated to children’s social competence. Smaller peer groups and longer interactions also demonstrated a positive association with these preschoolers’ social competence. The study shows the importance of outdoor physical play for preschoolers’ social success. Moreover, the study suggests that the environment in which children play has an important effect on the adaptive nature of their play.

John Frazer

John Frazer, Professor, trained at the Architectural Association, taught first at Cambridge University and then the AA in the 1970s and again in the '90s. He was Head of School of Design Research History and Criticism at the University of Ulster in the 1980s, he also ran a systems and design consultancy with his wife Julia (including projects for Cedric Price and Walter Segal) and was founder and chairman of Autographics software. He is currently Swire Chair Professor and Head of School of Design in Hong Kong.----- This is a very personal perspective on a concept of universal and future significance. It is personal, both is the sense that it is an unashamedly biased view of both the significance of the project, and the nature of that significance and because the author was personally involved as one of the consultants on GENERATOR and subsequently involved Cedric Price in its educational application at the Architectural Association. GENERATOR is still very much alive and was still developing whilst this chapter was being written.

Asia

Reporters sans frontiéres (RSF) has repeatedly declared Asia to be the most demanding continent for journalists and their news organizations to operate in, and in some countries, even simply to survive in. The many reports issued by RSF and other global agencies regularly show Asia to be the region in which the largest number of murders of journalists occur per year, even when Asian–Arabic states and Central Asia are not included in the definition of ‘Asia’. The reports describe numerous physical, legal and economic threats as well as serious political repression and restrictions that journalists face as they attempt to function as watch-dogs, agenda-setters and gate-keepers for their societies. The statistics and examples provided within these reports, however, do not provide the full picture. Most Asian nations also host vibrant media cultures in which journalists play an important role in supporting social and democratic processes and activities. This chapter outlines the political and economic influences on Asian journalism; the impact of new technologies; the debates about philosophies such as 'development journalism', 'peace journalism' and 'Asian values'; and the influence of the so-called 'envelope culture' or practices of gift-giving and bribery that pervade journalism in some countries. To illustrate how these principles affect journalists' practice, the chapter presents a comparison of the starkly contrasting situations in India versus North Korea (Democratic People's Republic of Korea). The chapter also describes issues affecting countries as far afield as China to Kazakhstan, including a short case study of journalism during the so-called Saffron Revolution in Burma in 2007. The chapter concludes with suggestions about how training and aid for the Asian should be contextualized to take into account the specific cultural, economic and political factors that shape and limit the media’s performance, and how journalists might be best placed to negotiate around them. Such training needs to be sensitive to valid variations in perceptions of what kind of governance and journalism best serves development, without serving politically motivated rhetoric.

Characteristic analysis for multisampled digital implementation of fixed-switching-frequency closed-loop modulation of voltage-source inverter

In this paper, a fixed-switching-frequency closed-loop modulation of a voltage-source inverter (VSI), upon the digital implementation of the modulation process, is analyzed and characterized. The sampling frequency of the digital processor is considered as an integer multiple of the modulation switching frequency. An expression for the determination of the modulation design parameter is developed for smooth modulation at a fixed switching frequency. The variation of the sampling frequency, switching frequency, and modulation index has been analyzed for the determination of the switching condition under closed loop. It is shown that the switching condition determined based on the continuous-time analysis of the closed-loop modulation will ensure smooth modulation upon the digital implementation of the modulation process. However, the stability properties need to be tested prior to digital implementation as they get deteriorated at smaller sampling frequencies. The closed-loop modulation index needs to be considered maximum while determining the design parameters for smooth modulation. In particular, a detailed analysis has been carried out by varying the control gain in the sliding-mode control of a two-level VSI. The proposed analysis of the closed-loop modulation of the VSI has been verified for the operation of a distribution static compensator. The theoretical results are validated experimentally on both single- and three-phase systems.

FPGA implementation of dual-microphone delay-and-sum beamforming for in-car speech enhancement and recognition

In an automotive environment, the performance of a speech recognition system is affected by environmental noise if the speech signal is acquired directly from a microphone. Speech enhancement techniques are therefore necessary to improve the speech recognition performance. In this paper, a field-programmable gate array (FPGA) implementation of dual-microphone delay-and-sum beamforming (DASB) for speech enhancement is presented. As the first step towards a cost-effective solution, the implementation described in this paper uses a relatively high-end FPGA device to facilitate the verification of various design strategies and parameters. Experimental results show that the proposed design can produce output waveforms close to those generated by a theoretical (floating-point) model with modest usage of FPGA resources. Speech recognition experiments are also conducted on enhanced in-car speech waveforms produced by the FPGA in order to compare recognition performance with the floating-point representation running on a PC.

Lighter than Tai

YEAR: 2008 ROLE: Performer FORMAT: Live Art Event at Tiananmen Square Beijing, China (3 hours) and Later on Summit of Mt. Tai Shan, Shandong Province, China (6 hrs + 3 hrs). WITH: Solo WHAT: In the Hall of Reverence on Tiananmen Square, Beijing Mao Zedong's body lies in state surrounded by flowers and draped with a Red Flag of Communist China. His casket with a glass top lies on a black stone from Mt. Tai, reflecting the quotation from Sima Qian (China's Han Dynasty historian) that "One's life can be weightier than Mt. Tai or lighter than a goose feather". This pair of performances were a quiet, personal reflection upon what such a once revolutionary expression might mean in today's very different time and place. The work was conceived during the Olympic Cultural Festival showing of Intimate Transactions (www.intimatetransactions.com) - during the tumultuous times leading up to China's proudly staged August 2008 Olympics. The rise and rise of China had long been generating major geopolitical, ecological and cross-cultural shifts throughout the region and beyond. In this dramatic epicentre of change and at a time of such great national pride, how might we each act in ways that are ecologically 'mighty' and yet simultaneously have an impact lighter than a goosefeather? This is both a question for China in its relations with the autonomous provinces and the environment as it is for all of us in our own 'local' affairs. However ecologically speaking all that is of local concern is of global concern and noone can therefore be exempt from the need to sustain that which we share in common and must all protect for the future. Performance 1: Tiananmen Square, Beijing: Dropping 100 goose feathers. Performance 2: The summit of Mt Tai, Shandong Province. Building a mountain from Goose Feathers. SHOWING HISTORY: 1: Anniversary of Protest Crackdown, Jun 8th 2008. 2: Dawn on Tai Shan's summit, 15th June, 2008 DETAILS: Performance 1: Begin an hour after dawn (5.45am) in Tiananmen Square Bring pre-prepared performance shirt, a bag of goose feathers tipped with red. Begin at the "Gate of Heavenly Peace" under the image of Chairman Mao. Circumnavigate the world's largest open and the most surveilled public space 5 times dropping feathers periodically. Meditate on Forces of Change. Finally enter Chairman Mao's mausoleum with the masses and move quietly past his preserved body. End the performance at the Gate of Heavenly Peace 3 hours later. Performance 2: Walk up Mt. Tai Shan in silence meditating on Forces of Change (6 hours). Stay overnight on the summit. Begin an hour before dawn (3.45am) in silence. Bring performance shirt, a sack of goose feathers and a simple wooden structure. On the sunrise viewing side of the mountain build a miniature, fragile 'mountain' in goose feathers and sticks on the edge of a sheer precipice. Watch the sun rise as the feathers blow away into the valley deep below (3 hours).

Vision-based topological mapping and localisation

Competent navigation in an environment is a major requirement for an autonomous mobile robot to accomplish its mission. Nowadays, many successful systems for navigating a mobile robot use an internal map which represents the environment in a detailed geometric manner. However, building, maintaining and using such environment maps for navigation is difficult because of perceptual aliasing and measurement noise. Moreover, geometric maps require the processing of huge amounts of data which is computationally expensive. This thesis addresses the problem of vision-based topological mapping and localisation for mobile robot navigation. Topological maps are concise and graphical representations of environments that are scalable and amenable to symbolic manipulation. Thus, they are well-suited for basic robot navigation applications, and also provide a representational basis for the procedural and semantic information needed for higher-level robotic tasks. In order to make vision-based topological navigation suitable for inexpensive mobile robots for the mass market we propose to characterise key places of the environment based on their visual appearance through colour histograms. The approach for representing places using visual appearance is based on the fact that colour histograms change slowly as the field of vision sweeps the scene when a robot moves through an environment. Hence, a place represents a region of the environment rather than a single position. We demonstrate in experiments using an indoor data set, that a topological map in which places are characterised using visual appearance augmented with metric clues provides sufficient information to perform continuous metric localisation which is robust to the kidnapped robot problem. Many topological mapping methods build a topological map by clustering visual observations to places. However, due to perceptual aliasing observations from different places may be mapped to the same place representative in the topological map. A main contribution of this thesis is a novel approach for dealing with the perceptual aliasing problem in topological mapping. We propose to incorporate neighbourhood relations for disambiguating places which otherwise are indistinguishable. We present a constraint based stochastic local search method which integrates the approach for place disambiguation in order to induce a topological map. Experiments show that the proposed method is capable of mapping environments with a high degree of perceptual aliasing, and that a small map is found quickly. Moreover, the method of using neighbourhood information for place disambiguation is integrated into a framework for topological off-line simultaneous localisation and mapping which does not require an initial categorisation of visual observations. Experiments on an indoor data set demonstrate the suitability of our method to reliably localise the robot while building a topological map.

Robust speech recognition using speech enhancement

Automatic Speech Recognition (ASR) has matured into a technology which is becoming more common in our everyday lives, and is emerging as a necessity to minimise driver distraction when operating in-car systems such as navigation and infotainment. In “noise-free” environments, word recognition performance of these systems has been shown to approach 100%, however this performance degrades rapidly as the level of background noise is increased. Speech enhancement is a popular method for making ASR systems more ro- bust. Single-channel spectral subtraction was originally designed to improve hu- man speech intelligibility and many attempts have been made to optimise this algorithm in terms of signal-based metrics such as maximised Signal-to-Noise Ratio (SNR) or minimised speech distortion. Such metrics are used to assess en- hancement performance for intelligibility not speech recognition, therefore mak- ing them sub-optimal ASR applications. This research investigates two methods for closely coupling subtractive-type enhancement algorithms with ASR: (a) a computationally-efficient Mel-filterbank noise subtraction technique based on likelihood-maximisation (LIMA), and (b) in- troducing phase spectrum information to enable spectral subtraction in the com- plex frequency domain. Likelihood-maximisation uses gradient-descent to optimise parameters of the enhancement algorithm to best fit the acoustic speech model given a word se- quence known a priori. Whilst this technique is shown to improve the ASR word accuracy performance, it is also identified to be particularly sensitive to non-noise mismatches between the training and testing data. Phase information has long been ignored in spectral subtraction as it is deemed to have little effect on human intelligibility. In this work it is shown that phase information is important in obtaining highly accurate estimates of clean speech magnitudes which are typically used in ASR feature extraction. Phase Estimation via Delay Projection is proposed based on the stationarity of sinusoidal signals, and demonstrates the potential to produce improvements in ASR word accuracy in a wide range of SNR. Throughout the dissertation, consideration is given to practical implemen- tation in vehicular environments which resulted in two novel contributions – a LIMA framework which takes advantage of the grounding procedure common to speech dialogue systems, and a resource-saving formulation of frequency-domain spectral subtraction for realisation in field-programmable gate array hardware. The techniques proposed in this dissertation were evaluated using the Aus- tralian English In-Car Speech Corpus which was collected as part of this work. This database is the first of its kind within Australia and captures real in-car speech of 50 native Australian speakers in seven driving conditions common to Australian environments.

Does research into sensitive areas do harm? Experiences of research participation after a child’s diagnosis with Ewing’s Sarcoma

Objective: To investigate family members’ experiences of involvement in a previous study (conducted August 1995 to June 1997) following their child’s diagnosis with Ewing’s sarcoma. Design: Retrospective survey, conducted between 1 November and 30 November 1997, using a postal questionnaire. Participants: Eighty-one of 97 families who had previously completed an in-depth interview as part of a national case–control study of Ewing’s sarcoma. Main outcome measures: Participants’ views on how participation in the previous study had affected them and what motivated them to participate. Results: Most study participants indicated that taking part in the previous study had been a positive experience. Most (n = 79 [97.5%]) believed their involvement would benefit others and were glad to have participated, despite expecting and finding some parts of the interview to be painful. Parents whose child was still alive at the time of the interview recalled participation as more painful than those whose child had died before the interview. Parents who had completed the interview less than a year before our study recalled it as being more painful than those who had completed it more than a year before. Conclusions: That people suffering bereavement are generally eager to participate in research and may indeed find it a positive experience is useful information for members of ethics review boards and other “gatekeepers”, who frequently need to determine whether studies into sensitive areas should be approved. Such information may also help members of the community to make an informed decision regarding participation in such research.

Flexible high-power multi DC-DC converters for train systems

This thesis reports on the investigations, simulations and analyses of novel power electronics topologies and control strategies. The research is financed by an Australian Research Council (ARC) Linkage (07-09) grant. Therefore, in addition to developing original research and contributing to the available knowledge of power electronics, it also contributes to the design of a DC-DC converter for specific application to the auxiliary power supply in electric trains. Specifically, in this regard, it contributes to the design of a 7.5 kW DC-DC converter for the industrial partner (Schaffler and Associates Ltd) who supported this project. As the thesis is formatted as a ‘thesis by publication’, the contents are organized around published papers. The research has resulted in eleven papers, including seven peer reviewed and published conference papers, one published journal paper, two journal papers accepted for publication and one submitted journal paper (provisionally accepted subject to few changes). In this research, several novel DC-DC converter topologies are introduced, analysed, and tested. The similarity of all of the topologies devised lies in their ‘current circulating’ switching state, which allows them to store some energy in the inductor, as extra inductor current. The stored energy may be applied to enhance the performance of the converter in the occurrence of load current or input voltage disturbances. In addition, when there is an alternating load current, the ability to store energy allows the converter to perform satisfactorily despite frequently and highly varying load current. In this research, the capability of current storage has been utilised to design topologies for specific applications, and the enhancement of the performance of the considered applications has been illustrated. The simplest DC-DC converter topology, which has a ‘current circulating’ switching state, is the Positive Buck-Boost (PBB) converter (also known as the non-inverting Buck-Boost converter). Usually, the topology of the PBB converter is operating as a Buck or a Boost converter in applications with widely varying input voltage or output reference voltage. For example, in electric railways (the application of our industrial partner), the overhead line voltage alternates from 1000VDC to 500VDC and the required regulated voltage is 600VDC. In the course of this research, our industrial partner (Schaffler and Associates Ltd) industrialized a PBB converter–the ‘Mudo converter’–operating at 7.5 kW. Programming the onboard DSP and testing the PBB converter in experimental and nominal power and voltage was part of this research program. In the earlier stages of this research, the advantages and drawbacks of utilization of the ‘current circulating’ switching state in the positive Buck-Boost converter were investigated. In brief, the advantages were found to be robustness against input voltage and current load disturbances, and the drawback was extra conduction and switching loss. Although the robustness against disturbances is desirable for many applications, the price of energy loss must be minimized to attract attention to the utilization of the PBB converter. In further stages of this research, two novel control strategies for different applications were devised to minimise the extra energy loss while the advantages of the positive Buck-Boost converter were fully utilized. The first strategy is Smart Load Controller (SLC) for applications with pre-knowledge or predictability of input voltage and/or load current disturbances. A convenient example of these applications is electric/hybrid cars where a master controller commands all changes in loads and voltage sources. Therefore, the master controller has a pre-knowledge of the load and input voltage disturbances so it can apply the SLC strategy to utilize robustness of the PBB converter. Another strategy aiming to minimise energy loss and maximise the robustness in the face of disturbance is developed to cover applications with unexpected disturbances. This strategy is named Dynamic Hysteresis Band (DHB), and is used to manipulate the hysteresis band height after occurrence of disturbance to reduce dynamics of the output voltage. When no disturbance has occurred, the PBB converter works with minimum inductor current and minimum energy loss. New topologies based on the PBB converter have been introduced to address input voltage disturbances for different onboard applications. The research shows that the performance of applications of symmetrical/asymmetrical multi-level diode-clamped inverters, DC-networks, and linear-assisted RF amplifiers may be enhanced by the utilization of topologies based on the PBB converter. Multi-level diode-clamped inverters have the problem of DC-link voltage balancing when the power factor of their load closes to unity. This research has shown that this problem may be solved with a suitable multi-output DC-DC converter supplying DClink capacitors. Furthermore, the multi-level diode-clamped inverters supplied with asymmetrical DC-link voltages may improve the quality of load voltage and reduce the level of Electromagnetic Interference (EMI). Mathematical analyses and experiments on supplying symmetrical and asymmetrical multi-level inverters by specifically designed multi-output DC-DC converters have been reported in two journal papers. Another application in which the system performance can be improved by utilization of the ‘current circulating’ switching state is linear-assisted RF amplifiers in communicational receivers. The concept of ‘linear-assisted’ is to divide the signal into two frequency domains: low frequency, which should be amplified by a switching circuit; and the high frequency domain, which should be amplified by a linear amplifier. The objective is to minimize the overall power loss. This research suggests using the current storage capacity of a PBB based converter to increase its bandwidth, and to increase the domain of the switching converter. The PBB converter addresses the industrial demand for a DC-DC converter for the application of auxiliary power supply of a typical electric train. However, after testing the industrial prototype of the PBB converter, there were some voltage and current spikes because of switching. To attenuate this problem without significantly increasing the switching loss, the idea of Active Gate Signalling (AGS) is presented. AGS suggests a smart gate driver that selectively controls the switching process to reduce voltage/current spikes, without unacceptable reduction in the efficiency of switching.