Dense Map Inference with User-Defined Priors: From Priorlets to Scan Eigenvariations

When mapping is formulated in a Bayesian framework, the need of specifying a prior for the environment arises naturally. However, so far, the use of a particular structure prior has been coupled to working with a particular representation. We describe a system that supports inference with multiple priors while keeping the same dense representation. The priors are rigorously described by the user in a domain-specific language. Even though we work very close to the measurement space, we are able to represent structure constraints with the same expressivity as methods based on geometric primitives. This approach allows the intrinsic degrees of freedom of the environment’s shape to be recovered. Experiments with simulated and real data sets will be presented

Aircraft trajectory simulator using a three degrees of freedom aircraft point mass model

Aircraft Operators Companies (AOCs) are always willing to keep the cost of a flight as low as possible. These costs could be modelled using a function of the fuel consumption, time of flight and fixed cost (over flight cost, maintenance, etc.). These are strongly dependant on the atmospheric conditions, the presence of winds and the aircraft performance. For this reason, much research effort is being put in the development of numerical and graphical techniques for defining the optimal trajectory. This paper presents a different approach to accommodate AOCs preferences, adding value to their activities, through the development of a tool, called aircraft trajectory simulator. This tool is able to simulate the actual flight of an aircraft with the constraints imposed. The simulator is based on a point mass model of the aircraft. The aim of this paper is to evaluate 3DoF aircraft model errors with BADA data through real data from Flight Data Recorder FDR. Therefore, to validate the proposed simulation tool a comparative analysis of the state variables vector is made between an actual flight and the same flight using the simulator. Finally, an example of a cruise phase is presented, where a conventional levelled flight is compared with a continuous climb flight. The comparison results show the potential benefits of following user-preferred routes for commercial flights.

Logic cells as basic structures to add/drop WDM information signals

Nowadays, in order to take advantage of fiber optic bandwidth, any optical communications system tends to be WDM. The way to extract a channel, characterized by a wavelength, from the optical fiber is to filter the specific wavelength. This gives the systems a low degree of freedom due to the fact of the static character of most of the employed devices. In this paper we will present a different way to extract channels from an optical fiber with WDM transmission. The employed method is based on an Optically Programmable Logic Cells (OPLC) previously published by us, for other applications as a chaotic generator or as basic element for optical computing. In this paper we will describe the configuration of the OPLC to be employed as a dropping device. It acts as a filter because it will extract the data carried by a concrete wavelength. It does depend, internally, on the wavelength. We will show how the intensity of the signal is able to select the chosen information from the line. It will be also demonstrated that a new idea of redundant information it is the way of selecting the concrete wavelength. As a matter of fact this idea is apparently the only way to use the OPLC as a dropping device. Moreover, based on these concepts, a similar way to route signals to different routes is reported. The basis is the use of photonic switching configurations, namely Batcher or Bayan structures, where the unit switching cells are the above indicated OPLCs.

Analysis of the geometric altimetry to support aircraft optimal trajectories within the future 4d trajectory management

Over the past few years, the common practice within air traffic management has been that commercial aircraft fly by following a set of predefined routes to reach their destination. Currently, aircraft operators are requesting more flexibility to fly according to their prefer- ences, in order to achieve their business objectives. Due to this reason, much research effort is being invested in developing different techniques which evaluate aircraft optimal trajectory and traffic synchronisation. Also, the inefficient use of the airspace using barometric altitude overall in the landing and takeoff phases or in Continuous Descent Approach (CDA) trajectories where currently it is necessary introduce the necessary reference setting (QNH or QFE). To solve this problem and to permit a better airspace management born the interest of this research. Where the main goals will be to evaluate the impact, weakness and strength of the use of geometrical altitude instead of the use of barometric altitude. Moreover, this dissertation propose the design a simplified trajectory simulator which is able to predict aircraft trajectories. The model is based on a three degrees of freedom aircraft point mass model that can adapt aircraft performance data from Base of Aircraft Data, and meteorological information. A feature of this trajectory simulator is to support the improvement of the strategic and pre-tactical trajectory planning in the future Air Traffic Management. To this end, the error of the tool (aircraft Trajectory Simulator) is measured by comparing its performance variables with actual flown trajectories obtained from Flight Data Recorder information. The trajectory simulator is validated by analysing the performance of different type of aircraft and considering different routes. A fuel consumption estimation error was identified and a correction is proposed for each type of aircraft model. In the future Air Traffic Management (ATM) system, the trajectory becomes the fundamental element of a new set of operating procedures collectively referred to as Trajectory-Based Operations (TBO). Thus, governmental institutions, academia, and industry have shown a renewed interest for the application of trajectory optimisation techniques in com- mercial aviation. The trajectory optimisation problem can be solved using optimal control methods. In this research we present and discuss the existing methods for solving optimal control problems focusing on direct collocation, which has received recent attention by the scientific community. In particular, two families of collocation methods are analysed, i.e., Hermite-Legendre-Gauss-Lobatto collocation and the pseudospectral collocation. They are first compared based on a benchmark case study: the minimum fuel trajectory problem with fixed arrival time. For the sake of scalability to more realistic problems, the different meth- ods are also tested based on a real Airbus 319 El Cairo-Madrid flight. Results show that pseudospectral collocation, which has shown to be numerically more accurate and computa- tionally much faster, is suitable for the type of problems arising in trajectory optimisation with application to ATM. Fast and accurate optimal trajectory can contribute properly to achieve the new challenges of the future ATM. As atmosphere uncertainties are one of the most important issues in the trajectory plan- ning, the final objective of this dissertation is to have a magnitude order of how different is the fuel consumption under different atmosphere condition. Is important to note that in the strategic phase planning the optimal trajectories are determined by meteorological predictions which differ from the moment of the flight. The optimal trajectories have shown savings of at least 500 [kg] in the majority of the atmosphere condition (different pressure, and temperature at Mean Sea Level, and different lapse rate temperature) with respect to the conventional procedure simulated at the same atmosphere condition.This results show that the implementation of optimal profiles are beneficial under the current Air traffic Management (ATM).

State Convergence Theory Applied to a Delayed Teleoperation System

State convergence is a control strategy that was proposed in the early 2000s to ensure stability and transparency in a teleoperation system under specific control gains values. This control strategy has been implemented for a linear system with or without time delay. This paper represents the first attempt at demonstrating, theoretically and experimentantally, that this control strategy can also be applied to a nonlinear teleoperation system with n degrees of freedom and delay in the communication channel. It is assumed that the human operator applies a constant force on the local manipulator during the teleoperation. In addition, the interaction between the remote manipulator and the environment is considered passive. Communication between the local and remote sites is made by means of a communication channel with variable time delay. In this article the theory of Lyapunov-Krasovskii was used to demonstrate that the local-remote teleoperation system is asymptotically stable.

Contribution to the analysis and design of reflectarray antennas for reconfigurable beam applications at frequencies above 100 GHz using liquid crystal technology

El trabajo contenido en esta tesis doctoral está encuadrado en el desarrollo de antenas reconfigurables electrónicamente capaces de proporcionar prestaciones competitivas a las aplicaciones cada vez más comunes que operan a frecuencias superiores a 60 GHz. En concreto, esta tesis se centra en el estudio, diseño, e implementación de las antenas reflectarray, a las que se introduce la tecnología de cristal líquido como elemento característico con el que se consigue reconfigurabilidad de haz de forma electrónica. Desde un punto de vista muy general, se puede describir un cristal líquido como un material cuya permitividad eléctrica es variable y controlada por una excitación externa, que generalmente suele corresponderse con un campo eléctrico quasi-estático (AC). Las antenas reflectarray de cristal líquido se han escogido como objeto de estudio por varias razones. La primera de ellas tiene que ver con las ventajas que los reflectarrays, y en especial aquellos realizados en configuración planar, proporcionan con respecto a otras antenas de alta ganancia como los reflectores o los “phased-arrays”. En los reflectarrays, la alimentación a través de una fuente primaria común (característica de reflectores) y el elevado número de grados de libertad de las celdas que los componen (característica de arrays) hacen que estas antenas puedan proporcionar prestaciones eléctricas iguales o mejores que las anteriores, a un coste más reducido y con estructuras de antena más compactas. La segunda razón radica en la flexibilidad que ofrece el cristal líquido a ser confinado y polarizado en recintos de geometría variada, como consecuencia de su fluidez (propiedad de los líquidos). Por ello, la tecnología de cristal líquido permite que el propio elemento reconfigurable en las celdas de reflectarray se adapte a la configuración planar de manera que en sí mismo, el cristal líquido sea una o varias de las capas características de esta configuración. Esto simplifica de forma drástica la estructura y la fabricación de este tipo de antenas, incluso si se comparan con reflectarrays reconfigurables basados en otras tecnologías como diodos, MEMS, etc. Por tanto, su coste y desarrollo es muy reducido, lo que hace que se puedan fabricar reflectarrays reconfigurables eléctricamente grandes, a bajo coste, y en producción elevada. Un ejemplo claro de una estructura similar, y que ha tenido éxito comercial, son las pantallas de cristal líquido. La tercera razón reside en el hecho de que el cristal líquido es, hasta la fecha, de las pocas tecnologías capaces de ofrecer reconfigurabilidad del haz a frecuencias superiores a 60 GHz. De hecho, el cristal líquido permite reconfigurabilidad en un amplio margen de frecuencias, que va desde DC a frecuencias del espectro visible, incluyendo las microondas y los THz. Otras tecnologías, como los materiales ferroeléctricos, el grafeno o la tecnología CMOS “on chip” permiten también conmutar el haz en estas frecuencias. Sin embargo, la tecnología CMOS tiene un elevado coste y actualmente está limitada a frecuencias inferiores a 150 GHz, y aunque los materiales ferroeléctricos o el grafeno puedan conmutar a frecuencias más altas y en un rango más amplio, tienen serias dificultades que los hacen aún inmaduros. En el caso de los materiales ferroeléctricos, los elevados voltajes para conmutar el material los hacen poco atractivos, mientras que en el caso del grafeno, su modelado aún está en discusión, y todavía no se han arrojado resultados experimentales que validen su idoneidad. Estas tres razones hacen que los reflectarrays basados en cristal líquido sean atractivos para multitud de aplicaciones de haz reconfigurable a frecuencias superiores a 60 GHz. Aplicaciones como radar de escaneo de imágenes de alta resolución, espectroscopia molecular, radiómetros para observación atmosférica, o comunicaciones inalámbricas de alta frecuencia (WiGig) son algunas de ellas. La tesis está estructurada en tres partes. En la primera de ellas se describen las características más comunes de los cristales líquidos, centrándonos en detalle en aquellas propiedades ofrecidas por este material en fase nemática. En concreto, se estudiará la anisotropía dieléctrica (Ae) de los cristales líquidos uniaxiales, que son los que se emplean en esta tesis, definida como la diferencia entre la permitividad paralela (£//) y la perpendicular (e±): Ae = e,, - e±. También se estudiará la variación de este parámetro (Ae) con la frecuencia, y el modelado electromagnético macroscópico más general que, extraído a partir de aquella, permite describir el cristal líquido para cada tensión de polarización en celdas de geometría planar. Este modelo es de suma importancia para garantizar precisión en el desfasaje proporcionado por las diferentes celdas reconfigurables para reflectarrays que se describirán en la siguiente parte de la tesis. La segunda parte de la tesis se centra en el diseño de celdas reflectarray resonantes basadas en cristal líquido. La razón por la que se escogen estos tipos de celdas reside en el hecho de que son las únicas capaces de proporcionar rangos de fase elevados ante la reducida anisotropía dieléctrica que ofrecen los cristales líquidos. El objetivo de esta parte trata, por tanto, de obtener estructuras de celdas reflectarray que sean capaces de proporcionar buenas prestaciones eléctricas a nivel de antena, mejorando sustancialmente las prestaciones de las celdas reportadas en el estado del arte, así como de desarrollar una herramienta de diseño general para aquellas. Para ello, se estudian las prestaciones eléctricas de diferentes tipos de elementos resonantes de cristal líquido que van, desde el más sencillo, que ha limitado el estado de la técnica hasta el desarrollo de esta tesis y que está formado por un sólo resonador, a elementos que constan de varios resonadores (multi-resonantes) y que pueden ser monocapa o multicapa. En un primer paso, el procedimiento de diseño de estas estructuras hace uso de un modelo convencional de cristal líquido que ha venido siendo usado en el estado del arte para este tipo de celdas, y que considera el cristal líquido como un material homogéneo e isótropo cuya permitividad varía entre (e/7) y (e±). Sin embargo, en esta parte de la tesis se demuestra que dicho modelado no es suficiente para describir de forma genérica el comportamiento del cristal líquido en las celdas tipo reflectarray. En la tesis se proponen procedimientos más exactos para el análisis y diseño basados en un modelo más general que define el cristal líquido como un material anisótropo e inhomogeneo en tres dimensiones, y se ha implementado una técnica que permite optimizar celdas multi-resonantes de forma eficiente para conseguir elevadas prestaciones en cuanto a ancho de banda, rango de fase, pérdidas, o sensibilidad al ángulo de incidencia. Los errores cometidos en el uso del modelado convencional a nivel de celda (amplitud y fase) se han analizado para varias geometrías, usando medidas de varios prototipos de antena que usan un cristal líquido real a frecuencias superiores a 100 GHz. Las medidas se han realizado en entorno periódico mediante un banco cuasi-óptico, que ha sido diseñado especialmente para este fin. Uno de estos prototipos se ha optimizado a 100 GHz para conseguir un ancho de banda relativamente elevado (10%), pérdidas reducidas, un rango de fase mayor de 360º, baja sensibilidad al ángulo de incidencia, y baja influencia de la inhomogeneidad transversal del cristal líquido en la celda. Estas prestaciones a nivel de celda superan de forma clara aquellas conseguidas por otros elementos que se han reportado en la literatura, de manera que dicho prototipo se ha usado en la última parte de la tesis para realizar diversas antenas de barrido. Finalmente, en esta parte se presenta una estrategia de caracterización de la anisotropía macroscópica a partir de medidas de los elementos de reflectarray diseñados en banco cuasi-óptico, obteniendo resultados tanto en las frecuencias de interés en RF como en AC, y comparándolas con aquellas obtenidas mediante otros métodos. La tercera parte de la tesis consiste en el estudio, diseño, fabricación y medida de antenas reconfigurables basadas en cristal líquido en configuraciones complejas. En reflectarrays pasivos, el procedimiento de diseño de la antena se limita únicamente al ajuste en cada celda de la antena de las dimensiones de las metalizaciones que se emplean para el control de fase, mediante procesos de optimización bien conocidos. Sin embargo, en el caso de reflectarrays reconfigurables basados en cristal líquido, resulta necesario un paso adicional, que consiste en calcular de forma adecuada las tensiones de control en cada celda del reflectarray para configurar la fase requerida en cada una de ellas, así como diseñar la estructura y los circuitos de control que permitan direccionar a cada elemento su tensión correspondiente. La síntesis de tensiones es por tanto igual o más importante que el diseño de la geometría de las celdas, puesto que éstas son las que están directamente relacionadas con la fase. En el estado del arte, existen varias estrategias de síntesis de tensiones que se basan en la caracterización experimental de la curva de fase respecto al voltaje. Sin embargo, esta caracterización sólo puede hacerse a un solo ángulo de incidencia y para unas determinadas dimensiones de celda, lo que produce que las tensiones sintetizadas sean diferentes de las adecuadas, y en definitiva que se alcancen errores de fase mayores de 70º. De esta forma, hasta la fecha, las prestaciones a nivel de antena que se han conseguido son reducidas en cuanto a ancho de banda, rango de escaneo o nivel de lóbulos secundarios. En esta última parte de la tesis, se introduce una nueva estrategia de síntesis de tensiones que es capaz de predecir mediante simulaciones, y con alta precisión, las tensiones que deben introducirse en cada celda teniendo en cuenta su ángulo de incidencia, sus dimensiones, la frecuencia, así como la señal de polarización definida por su frecuencia y forma de onda AC. Esta estrategia se basa en modelar cada uno de los estados de permitividad del cristal líquido como un sustrato anisótropo con inhomogeneidad longitudinal (1D), o en ciertos casos, como un tensor equivalente homogéneo. La precisión de ambos modelos electromagnéticos también se discute. Con el objetivo de obtener una herramienta eficiente de cálculo de tensiones, también se ha escrito e implementado una herramienta de análisis basada en el Método de los Momentos en el Dominio Espectral (SD-MoM) para sustratos estratificados anisótropos, que se usa en cada iteración del procedimiento de síntesis para analizar cada una de las celdas de la antena. La síntesis de tensiones se ha diseñado además para reducir al máximo el efecto del rizado de amplitud en el diagrama de radiación, que es característico en los reflectarrays que están formados por celdas con pérdidas elevadas, lo que en sí, supone un avance adicional para la obtención de mejores prestaciones de antena. Para el cálculo de los diagramas de radiación empleados en el procedimiento de síntesis, se asume un análisis elemento a elemento considerando periodicidad local, y se propone el uso de un método capaz de modelar el campo incidente de forma que se elimine la limitación de la periodicidad local en la excitación. Una vez definida la estrategia adecuada de cálculo de las tensiones a aplicar al cristal líquido en cada celda, la estructura de direccionamiento de las mismas en la antena, y diseñados los circuitos de control, se diseñan, fabrican y miden dos prototipos diferentes de antena de barrido electrónico a 100 GHz usando las celdas anteriormente presentadas. El primero de estos prototipos es un reflectarray en configuración “single offset” con capacidad de escaneo en un plano (elevación o azimut). Aunque previamente se realizan diseños de antenas de barrido en 2D a varias frecuencias en el rango de milimétricas y sub-milimétricas, y se proponen ciertas estrategias de direccionamiento que permiten conseguir este objetivo, se desarrolla el prototipo con direccionamiento en una dimensión con el fin de reducir el número de controles y posibles errores de fabricación, y así también validar la herramienta de diseño. Para un tamaño medio de apertura (con un numero de filas y columnas entre 30 y 50 elementos, lo que significa un reflectarray con un número de elementos superior a 900), la configuración “single offset” proporciona rangos de escaneo elevados, y ganancias que pueden oscilar entre los 20 y 30 dBi. En concreto, el prototipo medido proporciona un haz de barrido en un rango angular de 55º, en el que el nivel de lóbulos secundarios (SLL) permanece mejor de -13 dB en un ancho de banda de un 8%. La ganancia máxima es de 19.4 dBi. Estas prestaciones superan de forma clara aquellas conseguidas por otros autores. El segundo prototipo se corresponde con una antena de doble reflector que usa el reflectarray de cristal líquido como sub-reflector para escanear el haz en un plano (elevación o azimut). El objetivo básico de esta geometría es obtener mayores ganancias que en el reflectarray “single offset” con una estructura más compacta, aunque a expensas de reducir el rango de barrido. En concreto, se obtiene una ganancia máxima de 35 dBi, y un rango de barrido de 12º. Los procedimientos de síntesis de tensiones y de diseño de las estructuras de las celdas forman, en su conjunto, una herramienta completa de diseño precisa y eficiente de antenas reflectarray reconfigurables basados en cristales líquidos. Dicha herramienta se ha validado mediante el diseño, la fabricación y la medida de los prototipos anteriormente citados a 100 GHz, que consiguen algo nunca alcanzado anteriormente en la investigación de este tipo de antenas: unas prestaciones competitivas y una predicción excelente de los resultados. El procedimiento es general, y por tanto se puede usar a cualquier frecuencia en la que el cristal líquido ofrezca anisotropía dieléctrica, incluidos los THz. Los prototipos desarrollados en esta tesis doctoral suponen también unas de las primeras antenas de barrido real a frecuencias superiores a 100 GHz. En concreto, la antena de doble reflector para escaneo de haz es la primera antena reconfigurable electrónicamente a frecuencias superiores a 60 GHz que superan los 25 dBi de ganancia, siendo a su vez la primera antena de doble reflector que contiene un reflectarray reconfigurable como sub-reflector. Finalmente, se proponen ciertas mejoras que aún deben se deben realizar para hacer que estas antenas puedan ser un producto completamente desarrollado y competitivo en el mercado. ABSTRACT The work presented in this thesis is focused on the development of electronically reconfigurable antennas that are able to provide competitive electrical performance to the increasingly common applications operating at frequencies above 60 GHz. Specifically, this thesis presents the study, design, and implementation of reflectarray antennas, which incorporate liquid crystal (LC) materials to scan or reconfigure the beam electronically. From a general point of view, a liquid crystal can be defined as a material whose dielectric permittivity is variable and can be controlled with an external excitation, which usually corresponds with a quasi-static electric field (AC). By changing the dielectric permittivity at each cell that makes up the reflectarray, the phase shift on the aperture is controlled, so that a prescribed radiation pattern can be configured. Liquid Crystal-based reflectarrays have been chosen for several reasons. The first has to do with the advantages provided by the reflectarray antenna with respect to other high gain antennas, such as reflectors or phased arrays. The RF feeding in reflectarrays is achieved by using a common primary source (as in reflectors). This arrangement and the large number of degrees of freedom provided by the cells that make up the reflectarray (as in arrays), allow these antennas to provide a similar or even better electrical performance than other low profile antennas (reflectors and arrays), but assuming a more reduced cost and compactness. The second reason is the flexibility of the liquid crystal to be confined in an arbitrary geometry due to its fluidity (property of liquids). Therefore, the liquid crystal is able to adapt to a planar geometry so that it is one or more of the typical layers of this configuration. This simplifies drastically both the structure and manufacture of this type of antenna, even when compared with reconfigurable reflectarrays based on other technologies, such as diodes MEMS, etc. Therefore, the cost of developing this type of antenna is very small, which means that electrically large reconfigurable reflectarrays could be manufactured assuming low cost and greater productions. A paradigmatic example of a similar structure is the liquid crystal panel, which has already been commercialized successfully. The third reason lies in the fact that, at present, the liquid crystal is one of the few technologies capable of providing switching capabilities at frequencies above 60 GHz. In fact, the liquid crystal allows its permittivity to be switched in a wide range of frequencies, which are from DC to the visible spectrum, including microwaves and THz. Other technologies, such as ferroelectric materials, graphene or CMOS "on chip" technology also allow the beam to be switched at these frequencies. However, CMOS technology is expensive and is currently limited to frequencies below 150 GHz, and although ferroelectric materials or graphene can switch at higher frequencies and in a wider range, they have serious difficulties that make them immature. Ferroelectric materials involve the use of very high voltages to switch the material, making them unattractive, whereas the electromagnetic modelling of the graphene is still under discussion, so that the experimental results of devices based on this latter technology have not been reported yet. These three reasons make LC-based reflectarrays attractive for many applications that involve the use of electronically reconfigurable beams at frequencies beyond 60 GHz. Applications such as high resolution imaging radars, molecular spectroscopy, radiometers for atmospheric observation, or high frequency wireless communications (WiGig) are just some of them. This thesis is divided into three parts. In the first part, the most common properties of the liquid crystal materials are described, especially those exhibited in the nematic phase. The study is focused on the dielectric anisotropy (Ac) of uniaxial liquid crystals, which is defined as the difference between the parallel (e/7) and perpendicular (e±) permittivities: Ae = e,, - e±. This parameter allows the permittivity of a LC confined in an arbitrary volume at a certain biasing voltage to be described by solving a variational problem that involves both the electrostatic and elastic energies. Thus, the frequency dependence of (Ae) is also described and characterised. Note that an appropriate LC modelling is quite important to ensure enough accuracy in the phase shift provided by each cell that makes up the reflectarray, and therefore to achieve a good electrical performance at the antenna level. The second part of the thesis is focused on the design of resonant reflectarray cells based on liquid crystal. The reason why resonant cells have been chosen lies in the fact that they are able to provide enough phase range using the values of the dielectric anisotropy of the liquid crystals, which are typically small. Thus, the aim of this part is to investigate several reflectarray cell architectures capable of providing good electrical performance at the antenna level, which significantly improve the electrical performance of the cells reported in the literature. Similarly, another of the objectives is to develop a general tool to design these cells. To fulfill these objectives, the electrical yields of different types of resonant reflectarray elements are investigated, beginning from the simplest, which is made up of a single resonator and limits the state of the art. To overcome the electrical limitations of the single resonant cell, several elements consisting of multiple resonators are considered, which can be single-layer or multilayer. In a first step, the design procedure of these structures makes use of a conventional electromagnetic model which has been used in the literature, which considers that the liquid crystal behaves as homogeneous and isotropic materials whose permittivity varies between (e/7) y (e±). However, in this part of the thesis it is shown that the conventional modelling is not enough to describe the physical behaviour of the liquid crystal in reflectarray cells accurately. Therefore, a more accurate analysis and design procedure based on a more general model is proposed and developed, which defines the liquid crystal as an anisotropic three-dimensional inhomogeneous material. The design procedure is able to optimize multi-resonant cells efficiently to achieve good electrical performance in terms of bandwidth, phase range, losses, or sensitivity to the angle of incidence. The errors made when the conventional modelling (amplitude and phase) is considered have been also analysed for various cell geometries, by using measured results from several antenna prototypes made up of real liquid crystals at frequencies above 100 GHz. The measurements have been performed in a periodic environment using a quasi-optical bench, which has been designed especially for this purpose. One of these prototypes has been optimized to achieve a relatively large bandwidth (10%) at 100 GHz, low losses, a phase range of more than 360º, a low sensitivity to angle of incidence, and a low influence of the transversal inhomogeneity of the liquid crystal in the cell. The electrical yields of this prototype at the cell level improve those achieved by other elements reported in the literature, so that this prototype has been used in the last part of the thesis to perform several complete antennas for beam scanning applications. Finally, in this second part of the thesis, a novel strategy to characterise the macroscopic anisotropy using reflectarray cells is presented. The results in both RF and AC frequencies are compared with those obtained by other methods. The third part of the thesis consists on the study, design, manufacture and testing of LCbased reflectarray antennas in complex configurations. Note that the design procedure of a passive reflectarray antenna just consists on finding out the dimensions of the metallisations of each cell (which are used for phase control), using well-known optimization processes. However, in the case of reconfigurable reflectarrays based on liquid crystals, an additional step must be taken into account, which consists of accurately calculating the control voltages to be applied to each cell to configure the required phase-shift distribution on the surface of the antenna. Similarly, the structure to address the voltages at each cell and the control circuitry must be also considered. Therefore, the voltage synthesis is even more important than the design of the cell geometries (dimensions), since the voltages are directly related to the phase-shift. Several voltage synthesis procedures have been proposed in the state of the art, which are based on the experimental characterization of the phase/voltage curve. However, this characterization can be only carried out at a single angle of incidence and at certain cell dimensions, so that the synthesized voltages are different from those needed, thus giving rise to phase errors of more than 70°. Thus, the electrical yields of the LCreflectarrays reported in the literature are limited in terms of bandwidth, scanning range or side lobes level. In this last part of the thesis, a new voltage synthesis procedure has been defined and developed, which allows the required voltage to be calculated at each cell using simulations that take into account the particular dimensions of the cells, their angles of incidence, the frequency, and the AC biasing signal (frequency and waveform). The strategy is based on the modelling of each one of the permittivity states of the liquid crystal as an anisotropic substrate with longitudinal inhomogeneity (1D), or in certain cases, as an equivalent homogeneous tensor. The accuracy of both electromagnetic models is also discussed. The phase errors made by using the proposed voltage synthesis are better than 7º. In order to obtain an efficient tool to analyse and design the reflectarray, an electromagnetic analysis tool based on the Method of Moments in the spectral domain (SD-MoM) has also written and developed for anisotropic stratified media, which is used at each iteration of the voltage synthesis procedure. The voltage synthesis is also designed to minimize the effect of amplitude ripple on the radiation pattern, which is typical of reflectarrays made up of cells exhibiting high losses and represents a further advance in achieving a better antenna performance. To calculate the radiation patterns used in the synthesis procedure, an element-by-element analysis is assumed, which considers the local periodicity approach. Under this consideration, the use of a novel method is proposed, which avoids the limitation that the local periodicity imposes on the excitation. Once the appropriate strategy to calculate the voltages to be applied at each cell is developed, and once it is designed and manufactured both the structure to address the voltages to the antenna and the control circuits, two complete LC-based reflectarray antennas that operate at 100 GHz have been designed, manufactured and tested using the previously presented cells. The first prototype consists of a single offset reflectarray with beam scanning capabilities on one plane (elevation and azimuth). Although several LC-reflectarray antennas that provide 2-D scanning capabilities are also designed, and certain strategies to achieve the 2-D addressing of the voltage are proposed, the manufactured prototype addresses the voltages in one dimension in order to reduce the number of controls and manufacturing errors, and thereby validating the design tool. For an average aperture size (with a number of rows and columns of between 30 and 50 elements, which means a reflectarray with more than 900 cells), the single offset configuration provides an antenna gain of between 20 and 30 dBi and a large scanning range. The prototype tested at 100 GHz exhibits an electronically scanned beam in an angular range of 55º and 8% of bandwidth, in which the side lobe level (SLL) remains better than -13 dB. The maximum gain is 19.4 dBi. The electrical performance of the antenna is clearly an improvement on those achieved by other authors in the state of the art. The second prototype corresponds to a dual reflector antenna with a liquid crystal-based reflectarray used as a sub-reflector for beam scanning in one plane (azimuth or elevation). The main objective is to obtain a higher gain than that provided by the single offset configuration, but using a more compact architecture. In this case, a maximum gain of 35 dBi is achieved, although at the expense of reducing the scanning range to 12°, which is inherent in this type of structure. As a general statement, the voltage synthesis and the design procedure of the cells, jointly make up a complete, accurate and efficient design tool of reconfigurable reflectarray antennas based on liquid crystals. The tool has been validated by testing the previously mentioned prototypes at 100 GHz, which achieve something never reached before for this type of antenna: a competitive electrical performance, and an excellent prediction of the results. The design procedure is general and therefore can be used at any frequency for which the liquid crystal exhibits dielectric anisotropy. The two prototypes designed, manufactured and tested in this thesis are also some of the first antennas that currently operate at frequencies above 100 GHz. In fact, the dual reflector antenna is the first electronically scanned dual reflector antenna at frequencies above 60 GHz (the operation frequency is 100 GHz) with a gain greater than 25 dBi, being in turn the first dual-reflector antenna with a real reconfigurable sub-reflectarray. Finally, some improvements that should be still investigated to make these antennas commercially competitive are proposed.

Artefactos energéticos : de Fuller a Piñero (1961-1972) = Energetic artefacts : from Fuller to Piñero (1961-1972)

La obra de Emilio Pérez Piñero que se desarrolla entre los años 1961 y 1972 año en el que muere en un accidente de tráfico volviendo de Figueras, se centra principalmente en artefactos desplegables y desmontables, ejecutando prototipos que en el presente trabajo se han dividido en dos grupos; la cúpula reticular y la infraestructura. No pudo por tanto acudir al Congreso de 1972 de la UIA a recoger el premio Auguste Perret a la innovación tecnológica, que en años anteriores habían recibido Félix Candela, Jean Prouvé, Hans Scharoun o Frei Otto, y que en aquella ocasión tuvo que recoger su viuda. Parámetros como el de la movilidad, indeterminación, intercambiabilidad, obsolescencia y otros que se analizan en el presente trabajo, aparecen a lo largo de toda su obra ya que muchos de sus artefactos están ubicados en no-lugares y tienen un carácter itinerante y por tanto se hace indispensable su rápido montaje y desmontaje, que unas veces se resuelve mediante la desmontabilidad y otras con la plegabilidad de éstos. Aunque pueda parecer Piñero una figura autárquica, lo cierto es que durante la década donde concentra su trabajo se produce una explosión en torno a al arquetipo que será denominado de forma genérica `artefacto´, ligado conceptualmente a los parámetros que aquí se definen. Entendemos artefacto como objeto material realizado por una o varias personas para cumplir una función, es sinónimo de máquina y aparato y deriva de las palabras latinas ars o artis (técnica) y facto (hecho), para designar a los objetos cuya fabricación requiere alguna destreza. El término latino `ars´ engloba a las técnicas y a las artes, lo que no ocurre con el término castellano arte que deriva de él. Los movimientos utópicos que comparte la década con Piñero, utilizan el arquetipo infraestructural, ligero y high tech, para a través de una arquitectura más ligada a la ciencia ficción, realizar una crítica al Movimiento Moderno institucionalizado, todos ellos comparten cierta obsesión por la movilidad, ligada ésta a la idea de espacio flexible, dinámico, nómada. Este concepto de neo-nomadismo, que representa un habitar dinámico, aglutina las nuevas formas de vivir donde la movilidad social y geográfica son habituales. El nomadismo, por otra parte se entiende como sinónimo de democracia y libertad. La arquitectura pasa de ser pesada, estática, permanente a ser un elemento dinámico en continuo movimiento. A veces con connotaciones biológicas se asimilan los artefactos a organismos vivos y les confieren dichas propiedades de crecimiento y autonomía energética, acumulándose en torno a megaestructuras, donde quedan `enchufados´. En este intento de dotar movilidad a lo inmueble, se buscan estructuras vivas y modificables que crecen en una asimilación de las leyes naturales utilizando los parámetros de metamorfosis, simbiosis y cambio. Estos movimientos de vanguardia tienen también ciertas connotaciones políticas y sociales basadas en la libertad y la movilidad y reniegan del consumismo institucionalizado, de la arquitectura como instrumento de consumo, como objeto de usar en la cultura de masas. El carácter político de la autogestión, de la customización como parámetro proyectual, de la autosuficiencia energética, que anticipa la llegada de la crisis energética del año 1973. Objeto de este trabajo será relacionar los conceptos que aparecen fuertemente en el entorno de la década de los años sesenta del siglo XX, en el trabajo de Emilio Pérez Piñero. Parámetros encontrados como conceptos en los grupos de vanguardia y utopía a su vez fuertemente influenciados por las figuras del ingeniero Richard Buckminster Fuller y del arquitecto Konrad Wachsmann. Se analizará que posible influencia tiene la obra de Fuller, principalmente el prototipo denominado cúpula reticular, en la obra de Pérez Piñero y sus coetáneos analizando sus pensamientos teóricos en torno a parámetros como la energía, principalmente en las teorías relativas a Synergetics. El término inventado por Richard B. Fuller es una contracción de otro más largo que en inglés agrupa tres palabras; synergetic-energetic geometry. La definición de sinergia es la cooperación, es decir es el resultado de la acción conjunta de dos o más causas, pero con un efecto superior a la suma de estas causas. El segundo término, energetics geometry, que traducido sería geometría energética hace referencia en primer lugar a la geometría; ya que desarrolla el sistema de referencia que utiliza la naturaleza para construir sus sistemas y en segundo lugar a la energía; ya que además debe ser el sistema que establezca las relaciones más económicas utilizando el mínimo de energía. Por otro lado se analiza la repercusión del prototipo denominado Infraestructura, término acuñado por Yona Friedman y basado estructuralmente y conceptualmente en los desarrollos sobre grandes estructuras de Konrad Wachsmann. El arquitecto alemán divulga su conocimiento en seminarios impartidos por todo el mundo como el que imparte en Tokio y se denomina Wachsmann´s Seminar donde participan algunos de los componentes del grupo Metabolista que sorprenderán al mundo con sus realizaciones en la exposición de Osaka de 1970. El intervalo temporal entre 1961 hasta 1972 hace referencia a la horquilla donde Pérez Piñero realiza su obra arquitectónica, que comienza en 1961 cuando gana el concurso convocado en Londres por la UIA (Unión Internacional de Arquitectos) con el proyecto conocido como Teatro Ambulante, hasta 1972 que es cuando fallece volviendo de Figueras donde está realizando dos encargos de Salvador Dalí; la cubrición del escenario del futuro Teatro-Museo Salvador Dalí y la Vidriera Hipercúbica que debía cerrar la boca de tal escenario. Bajo el título de `Artefactos energéticos. De Fuller a Piñero (1961-1972)´, se presenta esta Tesis doctoral, que tiene la intención de vincular la obra de Emilio Pérez Piñero con la de las neo vanguardias producidas por una serie de arquitectos que operan en el ámbito internacional. Estas vinculaciones se producen de una forma general, donde a través de una serie de estrategias según la metodología que posteriormente se describe se buscan relaciones de la obra del autor español con algunos de los movimientos más significativos que aparecen en dicha década y de manera específica estableciendo relaciones con las obras y pensamientos de los autores que pertenecen a estos movimientos y donde estas relaciones se hacen más evidentes. El objeto del presente trabajo es analizar y explicar la obra del arquitecto Emilio Pérez Piñero, que espacialmente se localiza en el territorio español, desde el punto de vista de estos movimientos para posteriormente poder determinar si existen puntos en común y si el arquitecto español no solo comparte la década temporalmente sino también conceptualmente y por tanto utiliza el ideario que utilizan sus coetáneos que forman parte de las neovanguardias de los años sesenta de siglo XX. ABSTRACT ABSTRACT The Work of Emilio Perez Piñero was developed between the years 1961 and 1972 when he died in a car accident coming back from Figueres, where he was building a geodesic dome to close the building that enclose the Dali’s museum. All his Work is mainly centered in artifact that could be collapsible and removable, taking the two prototypes that are described in this work as a recurrent element in all his creation. These are the reticular dome and the infrastructure that are very influenced by the work from Richard B. Fuller and Konrad Wachsmann. Emilio Pérez Piñero could not receive the Auguste Perret Prize in 1972 awarded by the UIA that years before have received architects as Felix Candela, Jean Prouvé, Hans Scharoun or Frei Otto, and this time Pérez Piñero´s wife will accept it because of his death. Parameters like mobility, changeability, expendability, indetermination and others appear currently in his Work. All the inventions that Piñero had been patented and all of the artifacts that he created are usually located in no-places, because they do have a shifting identity. This kind of building has to be quickly set on site, and this problem has to be solved in term of foldability or demounting. In the decade where his work focuses, an explosion has occurred around this archetype to be generally called artifact that is usually linked to mobility. We understand artifact as a material object made by one or more people to work in a particular way. It is sometimes equated with the terms machinery and apparatus and it is derived from the Latin word `ars´ or `artis´, what means techniques and `facto´ (fact). And we use this term to refer to objects whose manufacture requires the same skill, in fact the Latin word `ars´ covers the techniques and arts, which does not occur with the Castillan term `arte´ that derives from it and means only art. The term neo-nomadic is a relatively new name used for a dynamic life, commonly referred to new forms of life where social and geographical mobility are common. On the other hand nomadic could be understood as a synonymous for democracy and freedom. The architecture is not going to be hard and static anymore but a dynamic element in the move. The Neo-avant-garde movement that shares the decade with Piñero uses this infrastructural archetype, which is light and high-tech, to criticize the institutionalized Modern Movement through architecture linked to science fiction. They all share an obsession with mobility, a concept that is connected to the terms `dynamic´, `nomadic´, `flexibile´, etc. Sometimes, with biological connotations, the utopian assimilate the artifacts to living organisms and give them these properties of growth and energy autonomy, and they apparently grow around megastructures where they are plugged. In this attempt to provide mobility to the inertness, living structures and possibility of change are sought in order to make them grow like a living organism and to assimilate the natural laws of growth. According to a definition from architecture provided by Fernández- Galiano who calls it `exosomatic artifact´, he understand architecture as artifact of the human environment that regulates natural energy flows and channels the energy stored in fuels for the benefit of living beings that inhabit. It is also true that during the sixties a new environmental awareness in public opinion is formed and that is due to the exploitation and disproportionate use of energy resources, acceleration of technological processes and mass consumption. Consequently a new concept is born: energy autonomy, it is very close to rational use of natural energy. Such a concept will be culturally assimilated with the requirement of independence not only in the management but also in the building construction until we arrive at energy autonomy. The individuals become energy consumer, which in turn can enter the energy produced in the system to `life in an eco-mode way´. The objectives of this research are analyzing all of these parameters and concepts that are coming into view in the surrounding of the decade and relate them with the Work of Pérez Piñero. Terms strongly present in the avant-garde movements around the decade, a young architect’s generation strongly influenced by Richard B. Fuller and Konrad Wachsmann. However, it will be analyzed how important the influence of Buckminster Fuller's Work was and his theoretical text about energy on the Work of Pérez Piñero and his fellows of the decade. The term Synergetic was invented by Fuller and came from the words synergy and energetic geometry. Synergy is the cooperation or interaction of two or more agents to produce a greater effect than the sum of their separate effects. Energetic geometry is related to the geometries that the Nature is using to build their construction but always using low energy consumption. On the other hand, the influences from Wachsmann around the prototype called Infrastructure have been analyzed. The German architect has developed knowledge around huge structures that he has spread all around the world through seminars that he has been conducted. One of these was the Wachsmann´s seminar in Tokyo, where same of the members of the Metabolist group were taking part of. Later these young architects will surprise the world with his artifacts at the World Exposition in Osaka in 1970. Between 1961 and 1972 Pérez Piñero produced his architectural work. It began in 1961 when he received the first prize with his project Mobile Theatre in the competition organized by the UIA in London. In 1972 the Auguste Perret Prize was granted by the UIA too. He could not accept it because he died before in a car accident when he was coming from Figueres, when he was designing two projects for Dali. With the title `Energetic Artifacts. From Fuller to Piñero (1961- 1972)´, this thesis relates the Work of Emilio Pérez Piñero with the neo avant-garde made by a young architects’ generation who is sharing the time with him. Several strategies have been used to formed relationships between them. They are described in the present work to set up a method that allows us to relate the work and ideas of the architects of the neo avant-garde with the ones from Piñero. This work is intended to analyze and explained the work of Pérez Piñero from the point of view of the international architects’ generation who is operating at the same time and finally to determinate if Piñero is not sharing the time with them but the concepts, ideas and architectural parameters.

Ethics and access to teaching materials in the medical library: the case of the Pernkopf atlas*

Conflicts can occur between the principle of freedom of information treasured by librarians and ethical standards of scientific research involving the propriety of using data derived from immoral or dishonorable experimentation. A prime example of this conflict was brought to the attention of the medical and library communities in 1995 when articles claiming that the subjects of the illustrations in the classic anatomy atlas, Eduard Pernkopf's Topographische Anatomie des Menschen, were victims of the Nazi holocaust. While few have disputed the accuracy, artistic, or educational value of the Pernkopf atlas, some have argued that the use of such subjects violates standards of medical ethics involving inhuman and degrading treatment of subjects or disrespect of a human corpse. Efforts were made to remove the book from medical libraries. In this article, the history of the Pernkopf atlas and the controversy surrounding it are reviewed. The results of a survey of academic medical libraries concerning their treatment of the Pernkopf atlas are reported, and the ethical implications of these issues as they affect the responsibilities of librarians is discussed.

Repacking protein cores with backbone freedom: structure prediction for coiled coils.

Progress in homology modeling and protein design has generated considerable interest in methods for predicting side-chain packing in the hydrophobic cores of proteins. Present techniques are not practically useful, however, because they are unable to model protein main-chain flexibility. Parameterization of backbone motions may represent a general and efficient method to incorporate backbone relaxation into such fixed main-chain models. To test this notion, we introduce a method for treating explicitly the backbone motions of alpha-helical bundles based on an algebraic parameterization proposed by Francis Crick in 1953 [Crick, F. H. C. (1953) Acta Crystallogr. 6, 685-689]. Given only the core amino acid sequence, a simple calculation can rapidly reproduce the crystallographic main-chain and core side-chain structures of three coiled coils (one dimer, one trimer, and one tetramer) to within 0.6-A root-mean-square deviations. The speed of the predictive method [approximately 3 min per rotamer choice on a Silicon Graphics (Mountain View, CA) 4D/35 computer] permits it to be used as a design tool.

A Qualitative Study of Potential Suicide Risk Factors Among Soldiers Transitioning From Operation Iraqi Freedom/Operation Enduring Freedom

Using qualitative methods, this study explored potential risk factors for suicide, as defined by Joiner's Interpersonal-Psychological Theory of Suicide (IPTS), in a population of Soldiers returning from deployment in Operation Enduring Freedom/Operation Iraqi Freedom (OEF/OIF). Sixty-eight Soldiers participated in semi-structured interviews during the period of transition from deployment to the garrison environment. These Soldiers were asked about changes in perception of pain, experiences of perceived burdensomeness, and lack of belonging. Interviews were transcribed and analyzed. A phenomenological methodology was employed (Creswell, 2006). In response to questions about perception of pain, Soldiers discussed both positive and negative changes in their experience of physical and emotional pain. When asked about experiences of perceived burdensomeness, Soldiers described changes related to deployment, such as injuries and combat related guilt, as well as changes related to transition from combat, including care seeking, reintegration into family and society, and emotional distancing. Regarding the experience of lack of belonging, Soldiers described difficulties related to the deployment, such as combat injuries, leadership roles, and individual differences, as well as difficulties related to reintegration such as symptoms of emotional numbing and distancing. Findings highlight the potential utility of IPTS in exploring both acute and chronic suicide risk factors associated with deployment and transition, as well as potential treatment strategies that may reduce suicide risk in the population of Soldiers during reintegration.

An Acceptance and Commitment Approach to Issues of Behavioral Health Care in Soldiers

For over a decade, the U.S. military has been engaged in two distinct, yet equally deadly conflicts: Operation Iraqi Freedom (OIF) and Operation Enduring Freedom (OEF). There are many physical and psychological effects of war necessitating the activation and interventions of a myriad of behavioral health professionals. The purpose of the paper was to understand how and if contemporary military culture may work to support or hinder application of an Acceptance and Commitment Therapy (ACT) approach to issues of psychological health among Soldiers. While the empirical research on efficacy with Soldiers is limited, a review of military culture revealed the promotion of rigid rule following, although effective in combat, influences the emotional control agenda and stigma while in garrison. However, empirical research demonstrating the clinical benefits and flexibility of ACT is rapidly emerging with civilian and Veteran populations. Suggested as a prevention technique utilized early in Soldier's training to increase psychological flexibility, ACT appears to demonstrate much promise in ameliorating the psychological consequences of war.

Dignity and the Eighth Amendment: A New Approach to Challenging Solitary Confinement

The use of solitary confinement in U.S. prisons and jails has come under increasing scrutiny. Over the past few months, Supreme Court Justice Anthony Kennedy all but invited constitutional challenges to the use of solitary confinement, while President Obama asked, “Do we really think it makes sense to lock so many people alone in tiny cells for 23 hours a day for months, sometime for years at a time?” Even some of the most notorious prisons and jails, including California’s Pelican Bay State Prison and New York’s Rikers Island, are reforming their use of solitary confinement because of successful litigation and public outcry. Rovner suggests that in light of these developments and “the Supreme Court’s increasing reliance on human dignity as a substantive value underlying and animating constitutional rights,” there is a strong case to make that long-term solitary confinement violates the constitutional right to freedom from cruel and unusual punishment.

Russia and the Common Space on Freedom, Security and Justice. CEPS Paper on Liberty and Security in Europe No. 54, 25 February 2013

EU-Russia cooperation in the framework of the Common Space on Freedom, Security and Justice, launched almost a decade ago in 2003, has borne fruit more in the security aspects than the justice and liberty-related policy areas. This study assesses the uneven cooperation on justice and home affairs between the EU and Russia, while delving into the intersection between cooperation on justice, liberty and security and the promotion of human rights, democracy and rule of law in EU-Russia relations. The study concludes by proposing a set of policy recommendations to the European Parliament for playing a more active role in this important field of cooperation between the EU and Russia.

The ‘Lisbonisation’ of the European Parliament: Assessing progress, shortcomings and challenges for democratic accountability in the area of freedom, security and justice. CEPS Paper on Liberty and Security in Europe No. 58, September 2013

This paper examines the performance of the European Parliament in EU AFSJ law and policy-making from the entry into force of the Lisbon Treaty until the end of the first half of 2013. The paper situates the EP in the new post-Lisbon institutional setting, documenting its transition to ‘AFSJ decision-maker’, and its new powers to shape and make policy covering the EU’s internal and external security agenda. While the paper finds that the EP has become an active co-owner of the EU AFSJ post-Lisbon, with the Parliament demonstrating a dynamic adjustment to its new post-Lisbon role and powers, the authors identify a set of new developments and challenges that have arisen in the conduct of democratic accountability by the EP in the AFSJ since 2009, which call for critical reflection ahead of the new parliamentary term 2014-2019 and the post-2014 phase of the EU’s AFSJ.