Hot turning of a difficult-to-machine steel (sae xev-f) aided by infrared radiation

A possible way for increasing the cutting tool life can be achieved by heating the workpiece in order to diminish the shear stress of material and thus decrease the machining forces. In this study, quartz electrical resistances were set around the workpiece for heating it during the turning. In the tests, heat-resistant austenitic alloy steel was used, hardenable by precipitation, mainly used in combustion engine exhaustion valves, among other special applications for industry. The results showed that in the hot machining the cutting tool life can be increased by 340% for the highest cutting speed tested and had a reduction of 205% on workpiece surface roughness, accompanied by a force decrease in relation to conventional turning. In addition, the chips formed in hot turning exhibited a stronger tendency to continuous chip formation indicating less energy spent in material removal process. Microhardness tests performed in the workpieces subsurface layers at 5 m depth revealed slightly higher values in the hot machining than in conventional, showing a tendency toward the formation of compressive residual stress into plastically deformed layer. The hot turning also showed better performance than machining using cutting fluid. Since it is possible to avoid the use of cutting fluid, this machining method can be considered better for the environment and for the human health.

Leaf-cutting ants: an unexpected microenvironment holding human opportunistic black fungi

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Yeasts found on an ephemeral reproductive caste of the leaf-cutting ant Atta sexdens rubropilosa

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Prospection of genomic regions divergently selected in racing line of Quarter Horses in relation to cutting line

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Integrated cutting machine programming and lot sizing in furniture industry

In this paper a mathematical model that combines lot-sizing and cutting-stock problems applied to the furniture industry is presented. The model considers the usual decisions of the lot sizing problems, as well as operational decisions related to the cutting machine programming. Two sets of a priori generated cutting patterns are used, industry cutting patterns and a class of n-group cutting patterns. A strategy to improve the utilization of the cutting machine is also tested. An optimization package was used to solve the model and the computational results, using real data from a furniture factory, show that a small subset of n-group cutting patterns provides good results and that the cutting machine utilization can be improved by the proposed strategy.

Cutting Ability of Nickel-titanium rotary systems protaper, mtwo and k3

Nickel-titanium rotatory systems should remove dentin during the root canal preparation to promote the enlargement and tapered shape with continuously narrowing towards the apex. Objective: The aim of this study was to analyze the cutting ability of three NiTi rotatory systems (n = 12): ProTaper (group 1), Mtwo (group 2), and K3 (group 3). Material and methods: Thirty six maxillary molar teeth were weighted on an analytical balance before and after the rotatory preparation of the mesio-buccal root canal. Data was statistically analyzed by ANOVA and Tukey s test with a significance level of 5%. Results: The results revealed the following mass differences (g) before and after the root canal preparation: ProTaper (group 1 – 0.0159 ± 0.004), Mtwo (group 2 – 0.0125 ± 0.002), and K3 (group 3 – 0.007 ± 0.003). Conclusion: ProTaper showed the highest cutting ability among the three tested nickel-titanium rotatory systems followed by Mtwo and K3.

Human teeth versus bovine teeth: cutting effectiviness of diamond burs

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Mitochondrial and peroxisomal population in post-pharyngeal glands of leaf-cutting ants after lipid supplementation

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

What is the stimulus for the excavation of fungus chamber in leaf-cutting ants?

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Comparative study of resistance to heat in two species of leaf-cutting ants

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Acromyrmex charruanus: a new inquiline social parasite species of leaf-cutting ants

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Prospection of genomic regions divergently selected in cutting line of quarter horses in relation to racing line

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Ground reaction forces during level ground walking with body weight unloading

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

The influence of handrim design on the contact forces on hands'surface: a preliminary study

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

First-year nest growth in the leaf-cutting ants Atta bisphaerica and Atta sexdens rubropilosa

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)