Direct Carbon-Carbon Bond Formation via Reductive Soft Enolization: A Kinetically Controlled syn-Aldol Addition of alpha-Halo Thioesters and Enolizable Aldehydes

The direct addition of enolizable aldehydes and a-halo thioesters to produce beta-hydroxy thioesters enabled by reductive soft enolization is reported. The transformation is operationally simple and efficient and has the unusual feature of giving high syn-selectivity, which is the opposite of that produced for (thio)esters under conventional conditions. Moreover, excellent diastereoselectivity results when a chiral nonracemic alpha-hydroxy aldehyde derivative is used.

Limited Excavations at the Gassaway-Feldmeyer House, 18AP49, 194 Prince George Street, Annapolis, Maryland

194 Prince George Street, known as the Gassaway-Feldmeyer house, was excavated in April of 1988. The property, in residential use from the 19th century, is owned by Historic Annapolis Foundation. Excavators found evidence of some intact 19th century levels and no trace of the 18th century. Unfortunately, parts of the site were disturbed by 20th century gardening activities. Further excavation is recommended since the Gassaway-Feldmeyer house may provide valuable information about residences in the 19th century.

Archaeological Testing at the John Brice II (Jennings-Brice) House, 18AP53, 195 Prince George Street, Annapolis, Maryland

In the fall of 1989, emergency excavation was undertaken in conjunction with restoration work at the John Brice II (Jennings-Brice) House, 18AP53. The exact date of construction for this brick home is problematic, and it was hoped that archaeological investigation could provide conclusive evidence to firmly establish the structure's date of construction. Excavation of one 5 X 5 ft. unit revealed the presence of 10 separate soil layers and four features of note, described in detail below. Unfortunately, no builders trench or similar feature by which we might date the house's construction was recovered. Future plans and possibilities for excavation at the property are outlined with the hopes of performing subsequent work at this rich site. We anticipate a focus on the arrangement and changes in use of the houselot, amassing evidence to support the presence of a vernacular garden on the property during the 18th century, as well as researching refuse disposal patterns, and clues to changing lifeways through the 18th century.

Wire bond reliability for power electronic modules - effect of bonding temperature

In this paper, thermal cycling reliability along with ANSYS analysis of the residual stress generated in heavy-gauge Al bond wires at different bonding temperatures is reported. 99.999% pure Al wires of 375 mum in diameter, were ultrasonically bonded to silicon dies coated with a 5mum thick Al metallisation at 25degC (room temperature), 100degC and 200degC, respectively (with the same bonding parameters). The wire bonded samples were then subjected to thermal cycling in air from -60degC to +150degC. The degradation rate of the wire bonds was assessed by means of bond shear test and via microstructural characterisation. Prior to thermal cycling, the shear strength of all of the wire bonds was approximately equal to the shear strength of pure aluminum and independent of bonding temperature. During thermal cycling, however, the shear strength of room temperature bonded samples was observed to decrease more rapidly (as compared to bonds formed at 100degC and 200degC) as a result of a high crack propagation rate across the bonding area. In addition, modification of the grain structure at the bonding interface was also observed with bonding temperature, leading to changes in the mechanical properties of the wire. The heat and pressure induced by the high temperature bonding is believed to promote grain recovery and recrystallisation, softening the wires through removal of the dislocations and plastic strain energy. Coarse grains formed at the bonding interface after bonding at elevated temperatures may also contribute to greater resistance for crack propagation, thus lowering the wire bond degradation rate

Shear bond strengths of glass-ionomer cements to sound and to prepared carious dentine

The aim of this study was determine whether bonding of glass-ionomer cements to non-carious dentine differed from that to carious dentine. Five commercial cements were used, namely Fuji IX GP, Fuji IX capsulated, Fuji IX Fast capsulated (all GC, Japan), Ketac-Molar and Ketac-Molar Aplicap (both 3M-ESPE, Germany). Following conditioning of the substrate with 10% poly (acrylic acid) for 10 s, sets of 10 samples of the cements were bonded to prepared teeth that had been removed for orthodontic reasons. The teeth used had either sound dentine or sclerotic dentine. Shear bond strengths were determined following 24 h storage. For the auto-mixed cements, shear bond strength to sound dentine was found not to differ statistically from shear bond strength to sclerotic dentine whereas for hand-mixed cements, shear bond to sound dentine was found to be higher than to carious dentine (to at least p < 0.05). This shows that the chemical effects arising from interactions of glass-ionomer cements with the mineral phase of the tooth are the most important in developing strong bonds, at least in the shorter term.