Advanced signal and receiver design for next generation OFDM systems

This thesis deal with the design of advanced OFDM systems. Both waveform and receiver design have been treated. The main scope of the Thesis is to study, create, and propose, ideas and novel design solutions able to cope with the weaknesses and crucial aspects of modern OFDM systems. Starting from the the transmitter side, the problem represented by low resilience to non-linear distortion has been assessed. A novel technique that considerably reduces the Peak-to-Average Power Ratio (PAPR) yielding a quasi constant signal envelope in the time domain (PAPR close to 1 dB) has been proposed.The proposed technique, named Rotation Invariant Subcarrier Mapping (RISM),is a novel scheme for subcarriers data mapping,where the symbols belonging to the modulation alphabet are not anchored, but maintain some degrees of freedom. In other words, a bit tuple is not mapped on a single point, rather it is mapped onto a geometrical locus, which is totally or partially rotation invariant. The final positions of the transmitted complex symbols are chosen by an iterative optimization process in order to minimize the PAPR of the resulting OFDM symbol. Numerical results confirm that RISM makes OFDM usable even in severe non-linear channels. Another well known problem which has been tackled is the vulnerability to synchronization errors. Indeed in OFDM system an accurate recovery of carrier frequency and symbol timing is crucial for the proper demodulation of the received packets. In general, timing and frequency synchronization is performed in two separate phases called PRE-FFT and POST-FFT synchronization. Regarding the PRE-FFT phase, a novel joint symbol timing and carrier frequency synchronization algorithm has been presented. The proposed algorithm is characterized by a very low hardware complexity, and, at the same time, it guarantees very good performance in in both AWGN and multipath channels. Regarding the POST-FFT phase, a novel approach for both pilot structure and receiver design has been presented. In particular, a novel pilot pattern has been introduced in order to minimize the occurrence of overlaps between two pattern shifted replicas. This allows to replace conventional pilots with nulls in the frequency domain, introducing the so called Silent Pilots. As a result, the optimal receiver turns out to be very robust against severe Rayleigh fading multipath and characterized by low complexity. Performance of this approach has been analytically and numerically evaluated. Comparing the proposed approach with state of the art alternatives, in both AWGN and multipath fading channels, considerable performance improvements have been obtained. The crucial problem of channel estimation has been thoroughly investigated, with particular emphasis on the decimation of the Channel Impulse Response (CIR) through the selection of the Most Significant Samples (MSSs). In this contest our contribution is twofold, from the theoretical side, we derived lower bounds on the estimation mean-square error (MSE) performance for any MSS selection strategy,from the receiver design we proposed novel MSS selection strategies which have been shown to approach these MSE lower bounds, and outperformed the state-of-the-art alternatives. Finally, the possibility of using of Single Carrier Frequency Division Multiple Access (SC-FDMA) in the Broadband Satellite Return Channel has been assessed. Notably, SC-FDMA is able to improve the physical layer spectral efficiency with respect to single carrier systems, which have been used so far in the Return Channel Satellite (RCS) standards. However, it requires a strict synchronization and it is also sensitive to phase noise of local radio frequency oscillators. For this reason, an effective pilot tone arrangement within the SC-FDMA frame, and a novel Joint Multi-User (JMU) estimation method for the SC-FDMA, has been proposed. As shown by numerical results, the proposed scheme manages to satisfy strict synchronization requirements and to guarantee a proper demodulation of the received signal.

Applications of RFID in the pharmaceutical supply chain

L’obiettivo di questa tesi è principalmente quello di mostrare le possibili applicazioni della tecnologia RFID (Radio Frequency Identification) all’interno della supply chain farmaceutica, cercando di comprendere il campo di applicazione di questa tecnologia in un’industria così altamente regolata e complessa come quella farmaceutica. La tesi è organizzata in tre sezioni; nel primo capitolo si trattano i principi alla base della tecnologia RFID e l’attuale stato dell’arte nella standardizzazione della banda di frequenza utilizzata e nell’hardware. In questa sezione sono poi mostrate le principali applicazioni e nella parte finale i problemi affrontati da un’azienda nell’applicare l’RFID al proprio business. Il secondo capitolo descrive le parti coinvolte nell’industria farmaceutica, dal produttore al consumatore finale, poi esamina le caratteristiche essenziali della supply chain farmaceutica e gli aspetti chiave e le criticità da affrontare in questo campo per essere efficiente e per consegnare il prodotto al cliente in maniera sicura e consistente. Infine nell’ultima sezione i due argomenti centrali sono fusi assieme, cercando di esaminare come la tecnologia RFID sia in grado di risolvere i problemi affrontati da tale industria. Il lavoro non vuole mostrare la tecnologia RFID come una panacea di tutte le problematiche presentate in questa industria, ma vuole cercare di colmare il gap presente in letteratura riguardo le possibili applicazioni di questa tecnologia nell’industria specificata.

Progetto di un convertitore di potenza autonomo per applicazioni di energy harvesting per radiofrequenza

Progetto di un circuito convertitore di potenza ottimizzato per essere alimentato da un antenna a RF in grado di estrarre potenza dalle bande a 900Mhz, 1750 MHz e 2450 MHz

Sistemi innovativi per il miglioramento della qualità e della sicurezza degli alimenti

Nell’attuale contesto, caratterizzato da un’elevata attenzione alla qualità e alla sicurezza degli alimenti e alle soluzioni tese a garantirli, l’implementazione di sistemi microelettronici per il controllo del prodotto attraverso supporti miniaturizzati e a basso costo può risultare un’opportunità strategica. Oggetto della ricerca di dottorato sono stati lo studio dell’utilizzo di sensori e strumentazione innovativi per la misurazione ed il controllo di parametri ambientali di conservazione di prodotti alimentari e per la loro identificazione mediante la tecnologia della radiofrequenza. Allo scopo è stato studiato il contesto in cui operano gli attori principali della filiera agroalimentare ed è stata sviluppata un’idea di etichetta progettata per essere in grado di emettere attivamente segnale di allarme in caso di necessità (etichetta RFID intelligente semi-passiva). Il prototipo di chip, realizzato in via sperimentale, è stato validato positivamente, sia come strumento di misura, sia in termini di prestazione nel caso studio del monitoraggio della conservazione di un prodotto alimentare in condizioni controllate di temperatura e radiazione luminosa. Le significative evidenze analitiche di reazioni di degradazione dello stato qualitativo del prodotto, quali analisi di pH e colore, raccolte durante il periodo di osservazione di 64 giorni, hanno trovato riscontro con le misure rilevate dal chip prototipo. I risultati invitano ad individuare un partner industriale, con il quale sperimentare l’applicazione della tecnologia proposta.

Numerical Modelling of Graphene Nanoribbon-fets for Analog and Digital Applications

Graphene, that is a monolayer of carbon atoms arranged in a honeycomb lattice, has been isolated only recently from graphite. This material shows very attractive physical properties, like superior carrier mobility, current carrying capability and thermal conductivity. In consideration of that, graphene has been the object of large investigation as a promising candidate to be used in nanometer-scale devices for electronic applications. In this work, graphene nanoribbons (GNRs), that are narrow strips of graphene, for which a band-gap is induced by the quantum confinement of carriers in the transverse direction, have been studied. As experimental GNR-FETs are still far from being ideal, mainly due to the large width and edge roughness, an accurate description of the physical phenomena occurring in these devices is required to have valuable predictions about the performance of these novel structures. A code has been developed to this purpose and used to investigate the performance of 1 to 15-nm wide GNR-FETs. Due to the importance of an accurate description of the quantum effects in the operation of graphene devices, a full-quantum transport model has been adopted: the electron dynamics has been described by a tight-binding (TB) Hamiltonian model and transport has been solved within the formalism of the non-equilibrium Green's functions (NEGF). Both ballistic and dissipative transport are considered. The inclusion of the electron-phonon interaction has been taken into account in the self-consistent Born approximation. In consideration of their different energy band-gap, narrow GNRs are expected to be suitable for logic applications, while wider ones could be promising candidates as channel material for radio-frequency applications.

Sistemi di comunicazione a corto raggio: analisi sperimentale con dispositivi NFC.

Una delle tecnologie radio che negli ultimi anni ha subito il maggior sviluppo è quella dell’identificazione a radio frequenza (Radio Frequency Identification), utilizzata in un gran numero di ambiti quali la logistica, il tracciamento, l’autenticazione e i pagamenti elettronici. Tra le tecnologie specifiche legate all’RFID si ritrova la Near Field Communication (NFC). Questa è una tecnologia di trasmissione dati a corto raggio che rappresenta un’evoluzione dell’RFID. Una delle caratteristiche dell’NFC è quella di instaurare una comunicazione tra due dispositivi in maniera semplice e intuitiva. L’oggetto che instaura la comunicazione è il Reader, nell’ambito RFID è un dispositivo altamente specializzato, poiché può lavorare a diverse frequenze operative. L’elemento innovativo che ha consentito il successo dell’NFC è il fatto che questa tecnologia possa integrare il Reader in uno strumento di comunicazione di largo uso, ovvero lo smartphone. Questo permette di inizializzare lo scambio dati, sia esso di lettura di un circuito integrato passivo o una trasmissione peer-to-peer, a seguito del naturale gesto di avvicinare lo smartphone. Analisti ed esperti del settore sono convinti del successo dell’NFC, nonostante siano state smentite le attese che vedevano l’NFC integrato in oltre la metà dei cellulari entro il 2010. Tra le molteplici applicazioni NFC in questo elaborato ci si soffermerà in particolare sul cosiddetto Smart Poster. Questo utilizzo può essere molto efficace avendo una gamma di impiego molto vasta. Per l’immagazzinamento dei dati nei Tag o nelle Smart Card si è utilizzato un protocollo d’incapsulamento dati chiamato NDEF (NFC Data Exchange Format) trattato nel capitolo 3 di questa trattazione. Nella seconda parte dell’elaborato si è realizzata una sperimentazione per misurare le distanze di funzionamento di cellulari e Reader per PC. In questo ambito si è realizzato quello che si è definito lo Smart Brick, cioè un mattone che comunica con dispositivi NFC grazie all’installazione di un Tag al suo interno. Si parlerà della realizzazione e degli strumenti software/hardware che hanno permesso di realizzare e programmare questo ”mattone elettronico”.

Integrated analysis and design of optimization and up-scaling of inductively coupled plasma synthesis of nanoparticles

This study is focused on radio-frequency inductively coupled thermal plasma (ICP) synthesis of nanoparticles, combining experimental and modelling approaches towards process optimization and industrial scale-up, in the framework of the FP7-NMP SIMBA European project (Scaling-up of ICP technology for continuous production of Metallic nanopowders for Battery Applications). First the state of the art of nanoparticle production through conventional and plasma routes is summarized, then results for the characterization of the plasma source and on the investigation of the nanoparticle synthesis phenomenon, aiming at highlighting fundamental process parameters while adopting a design oriented modelling approach, are presented. In particular, an energy balance of the torch and of the reaction chamber, employing a calorimetric method, is presented, while results for three- and two-dimensional modelling of an ICP system are compared with calorimetric and enthalpy probe measurements to validate the temperature field predicted by the model and used to characterize the ICP system under powder-free conditions. Moreover, results from the modeling of critical phases of ICP synthesis process, such as precursor evaporation, vapour conversion in nanoparticles and nanoparticle growth, are presented, with the aim of providing useful insights both for the design and optimization of the process and on the underlying physical phenomena. Indeed, precursor evaporation, one of the phases holding the highest impact on industrial feasibility of the process, is discussed; by employing models to describe particle trajectories and thermal histories, adapted from the ones originally developed for other plasma technologies or applications, such as DC non-transferred arc torches and powder spherodization, the evaporation of micro-sized Si solid precursor in a laboratory scale ICP system is investigated. Finally, a discussion on the role of thermo-fluid dynamic fields on nano-particle formation is presented, as well as a study on the effect of the reaction chamber geometry on produced nanoparticle characteristics and process yield.

Tunnelkontakte mit Heusler-Elektrode: Spinpolarisation von Co 2Cr 0,6Fe 0,4Al und Einfluss der Barriere

Ziel dieser Arbeit ist die Bestimmung der Spinpolarisation von der Heusler-Verbindung Co2Cr0,6Fe0,4Al. Dieses Ziel wurde durch die sorgfältige Präparation von Co2Cr0,6Fe0,4Al basierten Tunnelkontakten realisiert. Tunnelwiderstandsmessungen an Co2Cr0,6Fe0,4Al-basiertenrnTunnelkontakten ergaben einen Tunnelmagnetowiderstand von 101% bei 4 K. DieserrnTunnelmagnetowiderstand legt eine untere Grenze von 67% für die Spinpolarisation von Co2Cr0,6Fe0,4Al fest.rnrnCo2Cr0,6Fe0,4Al ist eine Heusler-Verbindung, der die Eigenschaften eines halbmetallischen Ferromagneten zugeschrieben werden. Ein halbmetallischer Ferromagnet hat an der Fermikante nur Elektronenspinzustände mit einer Polarisation. Als Folge davon können bei einem spinerhaltenden Tunnelprozess nur Elektronen einer Spinrichtung in den halbmetallischen Ferromagneten tunneln. Mit einem magnetischen Feld und einer durch einen Antiferromagneten fixierten Gegenelektrode, können an einem Tunnelkontakt mit einem spinpolarisierten Ferromagneten deshalb zwei Zustände, eine hohe und eine niedrige Tunnelleitfähigkeit, erzeugt werden. Daher finden spinpolarisierte Tunnelkontakte in Form von MRAM in der Datenspeicherung Verwendung. Bislang wurde jedoch keine Verbindung gefunden, der eine Spinpolarisation von 100% experimentell eindeutig nachgewiesen werden konnte. Für Co2Cr0,6Fe0,4Al lagen die höchsten gemessenen Spinpolarisationen um 50%.rnrnTunnelspektroskopie ist eine zuverlässige und anwendungsnahe Methode zur Untersuchung der Spinpolarisation. Inelastische Tunnelprozesse und eine reduzierte Ordnung an Grenzflächen bewirken einen reduzierten Tunnelmagnetowiderstand. Eine symmetriebrechende Barriere, wie amorphes AlOx, ist Voraussetzung für die Anwendung des Jullière-Modells zur Bestimmung der Spinpolarisation. Das Jullière-Modell verknüpft die Spin-aufgespaltenenrnZustandsdichten der Elektroden mit dem Tunnelmagnetowiderstand. Ohne einernsymmetriebrechende Barriere, zum Beispiel mit MgO als Isolatorschicht, können höhere Tunnelmagnetowiderstände erzwungen werden. Ein eindeutiger Rückschluss auf die Spinpolarisation ist dann jedoch nicht mehr möglich. Mit Aluminiumoxid-basierten Barrieren liefert die Anwendung des einfachen Jullière-Modells eine Untergrenze der Spinpolarisation.rnrnUm die Spinpolarisation von Co2Cr0,6Fe0,4Al durch Tunnelspektroskopie zu bestimmen, musste die Präparation der Tunnelkontakte verbessert werden. Dies wurde ermöglicht durch den Anbau einer neuen Sputterkammer mit besseren UHV-Bedingungen an ein bestehendes Präparationscluster. Co2Cr0,6Fe0,4Al wird mit Hilfe von Radiofrequenz-Kathodenzerstäuben deponiert. Die resultierenden Schichten verfügen nach ihrer Deposition über einen höheren Ordnungsgrad und über eine geordnete Oberfläche. Durch eine Magnesium-Pufferschicht war es möglich, auf diese Oberfläche eine homogene amorphe AlOx-Barriere zu deponieren. Als Gegenelektrode wurde CoFe als Ferromagnet mit MnFe als Antiferromagnet gewählt. Diese Gegenelektrode ermöglicht Tunnelmessungen bis hin zu Raumtemperatur.rnrnMit den in dieser Arbeit vorgestellten optimierten Analyse- und Präparationsmethoden ist es möglich, die Untergrenze der Spinpolarisation von Co2Cr0,6Fe0,4Al auf 67% anzuheben. Dies ist der bisher höchste veröffentlichte Wert der Spinpolarisation von Co2Cr0,6Fe0,4Al.rn

Interacting Bose-Fermi mixtures in optical lattices

In this thesis, we investigate mixtures of quantum degenerate Bose and Fermi gases of neutral atoms in threedimensional optical lattices. Feshbach resonances allow to control interspecies interactions in these systems precisely, by preparing suitable combinations of internal atomic states and applying external magnetic fields. This way, the system behaviour can be tuned continuously from mutual transparency to strongly interacting correlated phases, up to the stability boundary.rnThe starting point for these investigations is the spin-polarized fermionic band insulator. The properties of this non-interacting system are fully determined by the Pauli exclusion principle for the occupation of states in the lattice. A striking demonstration of the latter can be found in the antibunching of the density-density correlation of atoms released from the lattice. If bosonic atoms are added to this system, isolated heteronuclear molecules can be formed on the lattice sites via radio-frequency stimulation. The efficiency of this process hints at a modification of the atom number distribution over the lattice caused by interspecies interaction.rnIn the following, we investigate systems with tunable interspecies interaction. To this end, a method is developed which allows to assess the various contributions to the system Hamiltonian both qualitatively and quantitatively by following the quantum phase diffusion of the bosonic matter wave.rnBesides a modification of occupation number statistics, these measurements show a significant renormalization of the bosonic Hubbard parameters. The final part of the thesis considers the implications of this renormalization effect on the many particle physics in the mixture. Here, we demonstrate how the quantum phase transition from a bosonic superfluid to a Mott insulator state is shifted towards considerably shallower lattices due to renormalization.

Influence of defects and disorder on anomalous Hall effect and spin Seebeck effect on permalloy and Heusler compounds

In dieser Arbeit wurden dünne Schichten von Heusler-Verbindungen hergestellt und auf ihre Transporteigenschaften hin untersucht.rnDer Anomale Hall-Effekt (AHE) ist dabei von besonderem Interesse. Er ist ein seit langer Zeit bekannter, jedoch noch nicht vollständig verstandener Transport-Effekt. Die meisten Veröffentlichungen theoretischer Arbeiten konzentrieren sich auf den Einfluss eines bestimmten Beitrags zum AHE. Tatsächlich gemessene experimentelle Daten können jedoch oft nicht in Einklang mit idealisierten Annahmen gebracht werden. rnDie vorliegende Arbeit diskutiert die Ergebnisse, welche aus Messungen von Materialien mit niedrigem Restwiderstand erhalten wurden. rnrnAls prototypische Materialien wurden hier hyphenation Heusler-Verbindungen untersucht. Als Material mit einer komplexen Topologie der Fermi-Fläche zeichnet sich dort der Einfluss von Defekten und der Unordnung der Kristallstruktur deutlich ab.rnrnDurch Verwendung von Filmen mit unterschiedlichem Grad der Unordnung können verschiedene Streumechanismen unterschieden werden. Für Co$_{2}$FeSi$_{0.6}$Al$_{0.4}$ and Co$_{2}$FeGa$_{0.5}$Ge$_{0.5}$ zeigt sich ein positiver AHE bei einer Unordnung vom Typ B2 und bei einer induzierten temperaturabh"angigen Streuung, wo hingegen eine Typ DO$_{3}$-Unordnung zusammen mit anderen möglichen intrinsischen Beiträgen einen negativen Effekt hervorruft.rnrnDarüber hinaus wurden die magneto-optische Kerr-Effekte (MOKE) dieser Verbindungen untersucht. Hierfür wurden Beiträge erster Ordnung als Funktion der intrinsischen und extrinsischen Parameter qualitativ analysiert. Auf den Einfluss der kristallinen Ordnung auf Beiträge zweiter Ordnung des MOKE-Signals wird ebenfalls eingegangen.rnrnDes Weiteren wurden dünne Schichten der Heusler-Verbindung Co$_{2}$MnAl auf MgO- und Si-Subs-traten (beide (100)) mit Hochfrequenz-Mag-netron-Sputtern erzeugt. Die zusammensetzung sowie die magnetischen und Transport-Eigenschaften wurden hinsichtlich unterschiedlicher Abscheidebedingungen systematisch untersucht.rnrnInsbesondere zeigt der AHE-Widerstand ein außerordentliches temperaturunabhängiges Verhalten in einem Bereich moderater Magnetfeldstärken von 0 bis 0.6,T. Hierf"ur wurde der nicht-diagonale Transport bei Temperaturen bis zu 300,$^{circ}$C analysiert. Die Daten zeigen die Eignung des Materials für Hall-Sensoren auch oberhalb der Raumtemperatur.rnrnJüngst wurde der Spin Seebeck-Effekt (SSE) entdeckt. Der Effekt aus dem Bereich der Spin-Kaloritronik erzeugt eine Spin-Spannung'' aufgrund eines Temperaturgradienten in magnetischen Materialien. Hier werden vorläufige Messungen des SSE in Ni$_{80}$Fe$_{20}$ und in Heusler-Verbindungen präsentiert.rn

RFID tag localization with virtual multi-antenna systems

In questa tesi si sono valutate le prestazioni di un sistema di localizzazione multi-antenna di tag radio frequency identification (RFID) passivi in ambiente indoor. Il sistema, composto da un reader in movimento che percorre una traiettoria nota, ha come obiettivo localizzare il tag attraverso misure di fase; più precisamente la differenza di fase tra il segnale di interrogazione, emesso dal reader, e il segnale ricevuto riflesso dal tag che è correlato alla distanza tra di essi. Dopo avere eseguito una ricerca sullo stato dell’arte di queste tecniche e aver derivato il criterio maximum likelihood (ML) del sistema si è proceduto a valutarne le prestazioni e come eventuali fattori agissero sul risultato di localizzazione attraverso simulazioni Matlab. Come ultimo passo si è proceduto a effettuare una campagna di misure, testando il sistema in un ambiente reale. Si sono confrontati i risultati di localizzazione di tutti gli algoritmi proposti quando il reader si muove su una traiettoria rettilinea e su una traiettoria angolare, cercando di capire come migliorare i risultati.

Modifiche al protocollo di trasporto LTP per migliorarne le prestazioni in presenza di perdite elevate

La presente tesi si pone come obiettivo quello di analizzare il protocollo LTP (in particolare in ION) e proporre dei miglioramenti utili al caso in cui siano presenti perdite elevate. Piu in dettaglio, una prima parte introduttiva motiva l'inefficacia del TCP/IP in ambito interplanetario e introduce l'architettura DTN Bundle Protocol (Cap.1). La tesi prosegue con la descrizione delle specifiche del protocollo LTP (Cap.2), in particolar modo evidenziando come un bundle venga incapsulato in un blocco LTP, come questo sia successivamente diviso in tanti segmenti LTP e come questi vengano successivamente inviati con il protocollo UDP o con un protocollo analogo. Viene quindi presentata un'approfondita analisi delle penalizzazioni dovute alle perdite dei segmenti LTP, sia di tipo dati che di segnalazione (Cap. 3). Quest'analisi permette di dimostrare la criticita degli effetti delle perdite, in particolare per quello che riguarda i segmenti LTP di segnalazione. Mentre in presenza di perdite basse tali effetti hanno in media un impatto minimo sul tempo di consegna di un blocco LTP (quindi del bundle in esso contenuto), in quanto avvengono raramente, in presenza di perdite elevate rappresentano un collo di bottiglia per il tempo di consegna di un blocco LTP. A tal proposito sono state proposte alcune modifiche che permettono di migliorare le prestazioni di LTP (Cap. 4) compatibilmente con le specifiche RFC in modo da garantire l'interoperabilita con le diverse implementazioni del protocollo. Successivamente nel Cap. 5 viene mostrato come sono state implementate le modifiche proposte in ION 3.4.1. Nel capitolo finale (Cap. 6) sono presenti i risultati numerici relativi ad alcuni test preliminari eseguiti confrontando la versione originale del protocollo con le versioni modificate contenenti i miglioramenti proposti. I test sono risultati molto positivi per elevate perdite, confermando cosi la validita dell'analisi e dei miglioramenti introdotti.

Fine-tuning of substrate architecture and surface chemistry promotes muscle tissue development

Tissue engineering has been increasingly brought to the scientific spotlight in response to the tremendous demand for regeneration, restoration or substitution of skeletal or cardiac muscle after traumatic injury, tumour ablation or myocardial infarction. In vitro generation of a highly organized and contractile muscle tissue, however, crucially depends on an appropriate design of the cell culture substrate. The present work evaluated the impact of substrate properties, in particular morphology, chemical surface composition and mechanical properties, on muscle cell fate. To this end, aligned and randomly oriented micron (3.3±0.8 μm) or nano (237±98 nm) scaled fibrous poly(ε-caprolactone) non-wovens were processed by electrospinning. A nanometer-thick oxygen functional hydrocarbon coating was deposited by a radio frequency plasma process. C2C12 muscle cells were grown on pure and as-functionalized substrates and analysed for viability, proliferation, spatial orientation, differentiation and contractility. Cell orientation has been shown to depend strongly on substrate architecture, being most pronounced on micron-scaled parallel-oriented fibres. Oxygen functional hydrocarbons, representing stable, non-immunogenic surface groups, were identified as strong triggers for myotube differentiation. Accordingly, the highest myotube density (28±15% of total substrate area), sarcomeric striation and contractility were found on plasma-coated substrates. The current study highlights the manifold material characteristics to be addressed during the substrate design process and provides insight into processes to improve bio-interfaces.

UMTS base station-like exposure, well-being, and cognitive performance

BACKGROUND: Radio-frequency electromagnetic fields (RF EMF) of mobile communication systems are widespread in the living environment, yet their effects on humans are uncertain despite a growing body of literature. OBJECTIVES: We investigated the influence of a Universal Mobile Telecommunications System (UMTS) base station-like signal on well-being and cognitive performance in subjects with and without self-reported sensitivity to RF EMF. METHODS: We performed a controlled exposure experiment (45 min at an electric field strength of 0, 1, or 10 V/m, incident with a polarization of 45 degrees from the left back side of the subject, weekly intervals) in a randomized, double-blind crossover design. A total of 117 healthy subjects (33 self-reported sensitive, 84 nonsensitive subjects) participated in the study. We assessed well-being, perceived field strength, and cognitive performance with questionnaires and cognitive tasks and conducted statistical analyses using linear mixed models. Organ-specific and brain tissue-specific dosimetry including uncertainty and variation analysis was performed. RESULTS: In both groups, well-being and perceived field strength were not associated with actual exposure levels. We observed no consistent condition-induced changes in cognitive performance except for two marginal effects. At 10 V/m we observed a slight effect on speed in one of six tasks in the sensitive subjects and an effect on accuracy in another task in nonsensitive subjects. Both effects disappeared after multiple end point adjustment. CONCLUSIONS: In contrast to a recent Dutch study, we could not confirm a short-term effect of UMTS base station-like exposure on well-being. The reported effects on brain functioning were marginal and may have occurred by chance. Peak spatial absorption in brain tissue was considerably smaller than during use of a mobile phone. No conclusions can be drawn regarding short-term effects of cell phone exposure or the effects of long-term base station-like exposure on human health.

Feasibility of future epidemiological studies on possible health effects of mobile phone base stations

The increasing deployment of mobile communication base stations led to an increasing demand for epidemiological studies on possible health effects of radio frequency emissions. The methodological challenges of such studies have been critically evaluated by a panel of scientists in the fields of radiofrequency engineering/dosimetry and epidemiology. Strengths and weaknesses of previous studies have been identified. Dosimetric concepts and crucial aspects in exposure assessment were evaluated in terms of epidemiological studies on different types of outcomes. We conclude that in principle base station epidemiological studies are feasible. However, the exposure contributions from all relevant radio frequency sources have to be taken into account. The applied exposure assessment method should be piloted and validated. Short to medium term effects on physiology or health related quality of life are best investigated by cohort studies. For long term effects, groups with a potential for high exposure need to first be identified; for immediate effect, human laboratory studies are the preferred approach.