Transformation of carbon dioxide to diethyl carbonate over ceria and ceria-supported catalysts

Carbon dioxide is regarded, nowadays, as a primary anthropogenic greenhouse gas leading to global warming. Hence, chemical fixation of CO2 has attracted much attention as a possible way to manufacture useful chemicals. One of the most interesting approaches of CO2 transformations is the synthesis of organic carbonates. Since conventional production technologies of these compounds involve poisonous phosgene and carbon monoxide, there is a need to develop novel synthetic methods that would better match the principles of "Green Chemistry" towards protection of the environment and human health. Over the years, synthesis of dimethyl carbonate was under intensive investigation in the academia and industry. Therefore, this study was entirely directed towards equally important homologue of carbonic esters family namely diethyl carbonate (DEC). Novel synthesis method of DEC starting from ethanol and CO2 over heterogeneous catalysts based on ceria (CeO2) was studied in the batch reactor. However, the plausible drawback of the reaction is thermodynamic limitations. The calculated values revealed that the reaction is exothermic (ΔrHØ298K = ─ 16.6 J/ ) and does not occur spontaneously at rooms temperature (ΔrGØ 298K = 35.85 kJ/mol). Moreover, co-produced water easily shifts the reaction equilibrium towards reactants excluding achievement of high yields of the carbonate. Therefore, in-situ dehydration has been applied using butylene oxide as a chemical water trap. A 9-fold enhancement in the amount of DEC was observed upon introduction of butylene oxide to the reaction media in comparison to the synthetic method without any water removal. This result confirms that reaction equilibrium was shifted in favour of the desired product and thermodynamic boundaries of the reaction were suppressed by using butylene oxide as a water scavenger. In order to obtain insight into the reaction network, the kinetic experiments were performed over commercial cerium oxide. On the basis of the selectivity/conversion profile it could be concluded that the one-pot synthesis of diethyl carbonate from ethanol, CO2 and butylene oxide occurs via a consecutive route involving cyclic carbonate as an intermediate. Since commercial cerium oxide suffers from the deactivation problems already after first reaction cycle, in-house CeO2 was prepared applying room temperature precipitation technique. Variation of the synthesis parameters such as synthesis time, calcination temperature and pH of the reaction solution turned to have considerable influence on the physico-chemical and catalytic properties of CeO2. The increase of the synthesis time resulted in high specific surface area of cerium oxide and catalyst prepared within 50 h exhibited the highest amount of basic sites on its surface. Furthermore, synthesis under pH 11 yielded cerium oxide with the highest specific surface area, 139 m2/g, among all prepared catalysts. Moreover, CeO2─pH11 catalyst demonstrated the best catalytic activity and 2 mmol of DEC was produced at 180 oC and 9 MPa of the final reaction pressure. In addition, ceria-supported onto high specific surface area silicas MCM-41, SBA-15 and silica gel were synthesized and tested for the first time as catalysts in the synthesis of DEC. Deposition of cerium oxide on MCM-41 and SiO2 supports resulted in a substantial increase of the alkalinity of the carrier materials. Hexagonal SBA-15 modified with 20 wt % of ceria exhibited the second highest basicity in the series of supported catalysts. Evaluation of the catalytic activity of ceria-supported catalysts showed that reaction carried out over 20 wt % CeO2-SBA-15 generated the highest amount of DEC.

Effects of a methanolic fraction of soybean seeds on the transcriptional activity of peroxisome proliferator-activated receptors (PPAR)

Since the anti-inflammatory, antidiabetic and hypolipidemic effects of soy isoflavones may be mediated by activation of peroxisome proliferator-activated receptors (PPAR), the present study investigated whether the methanolic fractions obtained from soybean seeds (E1) and soybean seed coats with hypocotyls (E2) could influence PPARα, PPARγ and PPARβ/δ transcriptional activity. The isoflavones from E1 and E2 were quantified by HPLC analysis. E1 and E2 were rich in isoflavones (daidzin, glycitin, genistin, malonyldaidzin, malonylglycitin, malonylgenistin, daidzein, glycitein, and genistein). Moreover, E1 and E2 showed no evidence of genetically modified material containing the gene CP4 EPSPS. To investigate PPAR transcriptional activity, human promonocytic U-937 cells were treated with E1 and E2 (200, 400, 800, and 1600 µg/mL), positive controls or vehicle. Data are reported as fold-activation of the luciferase reporter driven by the PPAR-responsive element. Dose-response analysis revealed that E1 and E2 induced the transcriptional activity of PPARα (P < 0.001), with activation comparable to that obtained with 0.1 mM bezafibrate (positive control) at 1600 µg/mL (4-fold) and 800 µg/mL (9-fold), respectively. In addition, dose-response analysis revealed that E1 and E2 activated PPARβ/δ (P < 0.05), and the activation at 800 µg/mL (4- and 9-fold, respectively) was comparable to that of 0.1 mM bezafibrate (positive control). However, no effect on PPARγ was observed. Activation of PPARα is consistent with the lipid-lowering activity of soy isoflavones in vivo, but further studies are needed to determine the physiological significance of PPARβ/δ activation.

Antioxidant activity of rosemary and oregano ethanol extracts in soybean oil under thermal oxidation

Four experiments were conducted to measure the antioxidant activity of ethanol extracts of rosemary and oregano compared with synthetic antioxidants such as TBHQ and BHA/BHT. The antioxidant activity was determined and results differed from those of the Oven test at 63º C. Peroxide values and absorptivities at 232 nm of soybean oil under Oven test were lower in treatments with 25, 50, 75, 100 and 200 mg.Kg-1 TBHQ than in treatments with 1000 mg.Kg-1 oregano extract (O), 500 mg.Kg-1 rosemary extract (R) and their mixture R+O. All the treatments were effective in controlling the thermal oxidation of oils; the natural extracts were as effective as BHA+BHT and less effective than TBHQ. The natural extracts were mixed with 25, 50, 75 and 100 mg.Kg-1 TBHQ and then added to the oil. No improvement in antioxidative properties was observed. The best antioxidant concentration could be determined from polynomial regression and quadratic equation from the experimental data.

Volatile profile of heated soybean oil treated with quercetin and chlorogenic acid

Changes in the profile of volatile compounds after the heating of refined soybean oil without adding antioxidants, and treated with quercetin and chlorogenic acid (5-CQA) were investigated by GC/FID, GC/MS, and GC/SNIFFING. The heating temperature of the oil sample was 20 °C for the first minute, and then it was increased up to 160 °C at the rate of 10 °C min-1. The final temperature was kept for 10 minutes. 19 volatiles were identified in the heated samples without antioxidants. Medium-chain carbonyls predominated in the volatile fraction, mainly 2-heptenal, 2,4-heptadienal and 2,4-decadienal. Around 11 to 15 volatile compounds were detected in the heated samples treated with 5-CQA and quercetin, respectively. 5-CQA was not very efficient in delaying the formation of oxidative volatile compounds. The samples quercetin presented lower proportion of carbonyls with C6-C9.. The GC peak area data were used as an approach to estimate the relative content of each volatile compound and indicate that the samples treated with quercetin (p < 0.05) had significantly lower values for, 1-pentanol, 2,4-heptadienal, and 2,4-decadienal compared with those without antioxidants and treated with 5-CQA. GC/SNIFFING analysis revealed a smaller odor perception in the samples treated with 5-CQA compared to those without antioxidants. No odor was perceived in the heated samples treated with quercetin. These results indicate greater effectiveness of quercetin in delaying the formation of oxidative volatile compounds in soybean oils subjected to mild heating conditions. Apparently, biopolyphenols used in the present work showed good oxidative stability since no new volatile compound was detected in the heated samples treated with them.

Detection and quantification of Roundup Ready® soybean residues in sausage samples by conventional and real-time PCR

The increasing presence of products derived from genetically modified (GM) plants in human and animal diets has led to the development of detection methods to distinguish biotechnology-derived foods from conventional ones. The conventional and real-time PCR have been used, respectively, to detect and quantify GM residues in highly processed foods. DNA extraction is a critical step during the analysis process. Some factors such as DNA degradation, matrix effects, and the presence of PCR inhibitors imply that a detection or quantification limit, established for a given method, is restricted to a matrix used during validation and cannot be projected to any other matrix outside the scope of the method. In Brazil, sausage samples were the main class of processed products in which Roundup Ready® (RR) soybean residues were detected. Thus, the validation of methodologies for the detection and quantification of those residues is absolutely necessary. Sausage samples were submitted to two different methods of DNA extraction: modified Wizard and the CTAB method. The yield and quality were compared for both methods. DNA samples were analyzed by conventional and real-time PCR for the detection and quantification of Roundup Ready® soybean in the samples. At least 200 ng of total sausage DNA was necessary for a reliable quantification. Reactions containing DNA amounts below this value led to large variations on the expected GM percentage value. In conventional PCR, the detection limit varied from 1.0 to 500 ng, depending on the GM soybean content in the sample. The precision, performance, and linearity were relatively high indicating that the method used for analysis was satisfactory.

Physical properties of structured lipids from lard and soybean oil produced by enzymatic interesterification

The main goal of the present research was to evaluate the physical properties of blends of lard and soybean oil modified by enzymatic interesterification catalyzed by two different commercial (microbial) lipases, viz. from Candida cylindracea (AY30TM) and from Mucor circinelloides (M10TM). Pure lard exhibited a softening point of ca. 31.8 °C before interesterification, and this value shifted towards 29.1 °C after interesterification by AY30 lipase and towards 28.8 °C after interesterification by M10 lipase The interesterified lard exhibited lower consistency after reaction with both lipases, and this decrease was more pronounced for the reaction catalyzed by M10 lipase. This result was most likely due to the sn-1,3-specificity of M10 lipase. Pure lard displayed a lower SFC after interesterification, and M10 lipase proved to be more effective than AY30 lipase. The non-interesterified lard had a SFC of 31.3% at 10 °C, which was reduced to 23.8 and 19.9% after interesterification with AY30 lipase and M10 lipase, respectively. The lard and soybean oil blends were affected by the enzymatic interesterification and dilution with soybean oil.

Application of the Hsu model to soybean grain hydration

A comparative analysis of the theoretical-experimental study, developed by Hsu on the hydration of Amsoy 71 soybean grain, was performed through several soaking experiments using CD 202 soybean at 10, 20, 30, 40, and 50 °C, measuring moisture content over time. The results showed that CD 202 soybean equilibrium moisture content, Xeq, does not depend on temperature and is 21% higher than that found by Hsu, suggesting that soybean cultivar exerts great influence on Xeq. The Hsu model was numerically solved and its parameters were adjusted by the least squares method, with maximum deviations of +/- 10% relative to the experimental values. The limiting step in the mass transfer process during hydration corresponds to water diffusion inside the grain, leading to radial moisture gradients that decrease over time and with an increase in temperature. Regardless of the soybean cultivar, diffusivity increases as temperature or moisture content increases. However, the values of this transport property for Amsoy 71 were superior to those of CD 202, very close at the beginning of hydration at 20 °C and almost three times higher at the end of hydration at 50 °C.

The influence of different combinations of probiotic bacteria and fermentation temperatures on the microbiological and physicochemical characteristics of fermented lactic beverages containing soybean hydrosoluble extract during refrigerated storage

Lactic beverages containing probiotics were prepared with whole UHT milk, whey of Mozzarella cheese, soybean hydrosoluble extract and sugar. Three formulations were studied, each one containing a different combination of probiotic/starter bacteria, fermented at two different temperatures (37 and 45 °C). The aim of this work was to verify the influence of these variables on the viability of probiotic microorganisms and on the physicochemical stability of lactic beverages during storage under refrigeration (21 days at 7 °C). The results indicated that the fermentation temperature had a significant effect on the viability of probiotic bacteria. Counts for Lactobacillus acidophilus were affected by storage time, resulting appropriate after 21 days only for the beverage fermented at 37 °C. Physicochemical parameters did not exhibit drastic variations - proving the stability of formulations during storage. Cells of Bifidobacterium spp. showed high survival ability, probably due to the presence of growth promoters from soybean and cheese whey. The fermentation temperature of 37 °C allowed counts above the minimum limit for all the studied microorganisms, being preferred to the temperature of 45 °C. The inclusion of soybean hydrosoluble extract, a prebiotics source, resulted in a symbiotic product with more benefits to the health of consumers.

Physicochemical characteristics and functional properties of vitabosa (mucuna deeringiana) and soybean (glycine max)

Physicochemical characteristics and functional properties of vitabosa flour (Mucuna deeringiana) and soybean flour (Glycine max) were determined. Oil absorption capacity was higher in vitabosa. Water absorption capacity was higher in soy and it was affected by the change in the ionic strength of the medium. Emulsifying Activity (EA) decreased with increasing concentration of flour, while Emulsifying Stability (ES) showed an increased. EA and ES of flours have more ionic strength in the range between 0.0 and 0.4 M, but it is reduced afterwards with the higher concentration of NaCl. Foaming stability varied with the concentration of flour solution reaching maximum values of 39 and 33% for vitabosa and soybean, respectively at 10% flour concentration.Vitabosa had the best foaming capacity (56% to 0.6 M) compared with soybeans (47% to 0.4 M). Maximum capacity of gelation was observed in vitabosa at 10% flour concentration. Increases in ionic strength of the flour solution, at low salt concentrations (<0.4 M), improved the gelation of flours.

Effect of harvest at different times of day on the physical and chemical characteristics of vegetable-type soybean

The objective of this study was to evaluate the effect of harvest at different times of day on the chemical and physical characteristics of vegetable-type soybean BRS 267 cultivar, harvested at the R6 stage (seed development) and to compare it with that on the grains harvested at the R8 stage (maturation). The pods of the BRS 267 cultivar were harvested at the R6 stage (at 8:00 AM, 12:00 AM, and 6:00 PM), the color parameters were evaluated, and the grains were analyzed for chemical composition, activity inhibitor trypsin, phytic acid content, starch, sugars, fatty acids, and isoflavones. No differences were observed among the different harvest times in terms of the chemical constituents of vegetable-type soybean BRS 267 cultivar harvested at the R6 stage. Isoflavones content did not change with different harvest times, and the aglycone forms (daidzein, glycitein, and genistein) were found in smaller quantities at the R6 stage compared to the R8 stage. The color of the pods of soybean BRS 267 cultivar, harvested at the R6 stage did not change with different harvest times. The grains harvested at the R6 stage had lower protein content, phytic acid, and sucrose and higher levels of lipids, carbohydrates, starch, glucose, fructose, stachyose, and linolenic acids than those collected at the R8 stage. The different times of harvest did not affect the quality of the vegetable-type soybean BRS 267 cultivar harvested at stage R6. Nevertheless, it is recommended to harvest in the morning, when the temperature is milder, like other vegetables, to facilitate and optimize its marketing and in natura consumption.

Chemical composition of tempeh from soybean cultivars specially developed for human consumption

Tempeh is a food obtained by fermentation of soybean grains by the fungus Rizophus oligosporus. It is a traditional Indonesian food that presents benefits for human health protecting against diarrhea and chronic diseases. Tempeh processing includes dehulling, cooking, inoculation, and fermentation. In this study, chemical characteristics of tempeh prepared with soybean cultivars specially developed for human consumption (BRS 216, BRS 232, BRS 257, and BRS 267) were investigated. Soybean grains and tempeh obtained from these cultivars were analyzed for oil, protein, antinutrional factors, and isoflavone content. Cultivar BRS 216 presented the highest protein content in the grains (36.81%) and in tempeh (51.99%). On average, the protein content in tempeh increased 16% in relation to that of soybean grains. Isoflavone content was higher in the grains than in tempeh with significant differences among the cultivars. However, the aglycones content increased about 50% in tempeh (49.00 mg.100 g-1 on average) compared to that of raw material (soybean grains - 21.49 mg.100 g-1, on average). The content of Kunitz trypsin inhibitor (KSTI) reduced 83% in tempeh, on average, as compared to the value found in the grains. Phytic acid content was similar in both tempeh and the grains.

Heat-treatment reduces anti-nutritional phytochemicals and maintains protein quality in genetically improved hulled soybean flour

The soybean is a protein source of high biological value. However, the presence of anti-nutritional factors affects its protein quality and limits the bioavailability of other nutrients. The effect of heat-treatment, 150 ºC for 30 minutes, on hulled and hull-less soybean flour from the cultivar UFVTN 105AP on urease, trypsin inhibitor activity, protein solubility, amino acid profile, and in vivo protein quality was investigated. The treatment reduced the trypsin inhibitor activity and urease, but it did not affect protein solubility. Protein Efficiency Coefficient (PER) values of the flours were similar, and the PER of the hull-less soybean flour did not differ from casein. The Net Protein Ratio (NPR) did not differ between the experimental groups. The True Digestibility (TD) of the flours did not differ, but both were lower in casein and the Protein Digestibility Corrected Amino Acid Score (PDCCAS) was lower than the TD, due to limited valine determined by the chemical score. Therefore, the flours showed reduced anti-nutritional phytochemicals and similar protein quality, and therefore the whole flours can be used as a source of high quality protein.

Optimization of extrusion variables for the production of snacks from by-products of rice and soybean

This study aimed to define the process conditions to obtain snacks from the by-products of rice and soybean with physical characteristics suitable for marketing. Therefore, the effects of moisture and extrusion temperature on the expansion and color of the products obtained experimentally obtained were evaluated, and the proximate composition of the by-products and that of the snack with greater desirability were determined. Response surface methodology and rotational central composite design were used, and desirability test based on the regression models adjusted was applied. The most desirable snack, with the highest expansion index (3.39), specific volume (13.5 mL.g-1), and the chromaticity coordinate a* (2.79), was obtained under 12 g.100 g-1 moisture and 85ºC of temperature in the third zone of the extruder. The snack produced under these conditions attained content of protein and lipid content 41 and 64% higher than that of the traditional corn snack. It can be concluded that producing extruded snack made form a mixture of broken grains, rice bran, and soybean okara (81:9:10) is technologically feasible, enabling the development of a new product with good nutritional value that can improve the diet of children, the main consumers of this type of food.

Tempeh flour as a substitute for soybean flour in coconut cookies

The objective of this study was to prepare roasted and lyophilized tempeh flour with soybean cultivar BRS 267 to apply them in the formulation of coconut biscuits. The cookies produced with whole soy flour and mixed flour of soybean and tempeh were evaluated for proximate composition, fatty acid profile, and isoflavone aglycones in order to verify the effects of inoculation with the fungus Rhizopus oligosporus and those of the drying processes of roasting and lyophilization on the chemical characteristics of the final product. Sensory acceptance and purchase intention of the formulated products were also evaluated. The results indicate the maintenance of linolenic acid, which is important in the prevention of coronary diseases, and an increase in the aglycones levels when the tempeh flour was used. Lipids and proteins showed differences, and the sensory analyses demonstrated similarity between the cookies with satisfactory scores for aroma, flavor, texture, and overall acceptability for both samples. when compared to the control. Purchase intent was also positive for the lyophilized and toasted tempeh flours, thus enabling the use of the roasting process as a simple drying method, for processing tempeh and obtaining a flour rich in proteins and aglycones that can be used as a partial substitute for soy flour in cookies and other bakery products.