Solid electrolytes for electrochromic devices based on reversible metal electrodeposition

Air conditioning and lighting costs can be reduced substantially by changing the optical properties of "intelligent windows." The electrochromic devices studied to date have used copper as an additive. Copper, used here as an electrochromic material, was dissolved in an aqueous animal protein-derived gel electrolyte. This combination constitutes the electrochromic system for reversible electrodeposition. Cyclic voltammetry, chronoamperometric and chromogenic analyses indicated that were obtained good conditions of transparency (initial transmittance of 70%), optical reversibility, small potential window (2.1 V), variation of transmittance in visible light (63.6%) and near infrared (20%) spectral regions. Permanence in the darkened state was achieved by maintaining a lower pulse potential (-0.16 V) than the deposition potential (-1.0 V). Increasing the number of deposition and dissolution cycles favored the transmittance and photoelectrochemical reversibility of the device. The conductivity of the electrolyte (10(-3) S/cm) at several concentrations of CuCl2 was determined by electrochemical impedance spectroscopy. A thermogravimetric analysis confirmed the good thermal stability of the electrolyte, since the mass loss detected up to 100 degrees C corresponded to water evaporation and decomposition of the gel started only at 200 degrees C. Micrographic and small angle X-ray scattering analyses indicated the formation of a persistent deposit of copper particles on the ITO. (C) 2012 Elsevier B.V. All rights reserved.

Antimicrobial Photodynamic Therapy for the Treatment of Teeth with Apical Periodontitis: A Histopathological Evaluation

Introduction: This study evaluated the in vivo response of apical and periapical tissues of dogs' teeth with apical periodontitis after one-session endodontic treatment with and without antimicrobial photodynamic therapy (aPDT). Methods: Sixty root canals with experimentally induced apical periodontitis were instrumented and assigned to 4 groups receiving aPDT and root canal filling (RCF) or not: group aPDT+/RCF- (n = 20): aPDT (photosensitizer phenothiazine chloride at 10 mg/mL for 3 minutes and diode laser [2 = 660 nm, 60 mW/cm(2)] for 1 minute) and RCF in the same session; group aPDT+/RCF (n = 10); group aPDT /RCF+ (n = 20), and group aPDT /RCF (n = 10). Teeth were restored, and the animals were killed after 90 days. Sections from the maxillas and mandibles were stained with hematoxylin-eosin and Mallory trichrome and examined under light microscopy. Descriptive (ie, newly formed apical mineralized tissue, periapical inflammatory infiltrate, apical periodontal ligament thickness, and mineralized tissue resorption) and quantitative (ie, periapical lesion size and number of inflammatory cells) microscopic analysis was performed. Quantitative data were analyzed by the Kruskal-Wallis and Dunn tests (alpha =.05). Results: In the aPDT-treated groups, the periapical region was moderately/severely enlarged with no inflammatory cells, moderate neoangiogenesis and fibrogenesis, and the smallest periapical lesions. Conclusions: Although apical closure by mineralized tissue deposition was not achieved, the absence of inflammatory cells, moderate neoangiogenesis, and fibrogenesis in the periapical region in the groups treated with aPDT indicate that this can be a promising adjunct therapy to cleaning and shaping procedures in teeth with apical periodontitis undergoing one-session endodontic treatment. (J Endod 2012;38:360-366)

Sevenfold enhancement on porphyrin dye efficiency by coordination of ruthenium polypyridine complexes

Sevenfold enhancement of photoconversion efficiency was achieved by incorporation of peripheral ruthenium complexes to a porphyrin dye, generating supramolecular effects capable of playing several key roles (e.g., transferring energy to, inhibiting aggregation, and accepting the hole generated in the porphyrin center after electron injection), providing new insights for the design of better DSSC photosensitizers.

Photodynamic inactivation of microorganisms present on complete dentures. A clinical investigation

The aim of this study was to evaluate the effectiveness of photodynamic therapy (PDT) for the disinfection of complete dentures. Biofilm samples were collected from dentures of 60 denture users who were randomly divided into four experimental groups (n = 15 each): subjects whose maxillary dentures were sprayed with 50 and 100 mg/l of PhotogemA (R) suspension (groups P50S and P100S) and patients whose maxillary dentures were treated with 50 and 100 mg/l of PhotogemA (R) gel (groups P50G and P100G). Dentures with photosensitizers were left in the dark for 30 min (pre-irradiation time) and then irradiated with blue LED light at 37.5 J/cm(2) (26 min). Denture samples were taken with sterile cotton swab before (left side surfaces) and after (right side surfaces) PDT. All microbial material was diluted and plated on selective media for Candida spp., Staphylococcus mutans spp., streptococci and a non-selective media. After incubation (48 h/37A degrees C), the number of colony-forming units (cfu/ml) was counted. Microorganisms grown on selective media were identified using biochemical methods before and after PDT. The data were submitted to McNemar and Kruskal-Wallis tests (alpha = 0.05). No growth after PDT was observed in 60, 53, 47, and 40% of dentures from P100G, P50G, P100S, and P50S groups, respectively. When evidence of microorganisms' growth was observed, PDT regimens eliminated over 90% of microorganisms on dentures. This clinical study showed that PDT was effective for disinfecting dentures.

Feasibility Study of a Solar Reactor for Phenol Treatment by the Photo-Fenton process in Aqueous Solution

Solar reactors can be attractive in photodegradation processes due to lower electrical energy demand. The performance of a solar reactor for two flow configurations, i.e., plug flow and mixed flow, is compared based on experimental results with a pilot-scale solar reactor. Aqueous solutions of phenol were used as a model for industrial wastewater containing organic contaminants. Batch experiments were carried out under clear sky, resulting in removal rates in the range of 96100?%. The dissolved organic carbon removal rate was simulated by an empirical model based on neural networks, which was adjusted to the experimental data, resulting in a correlation coefficient of 0.9856. This approach enabled to estimate effects of process variables which could not be evaluated from the experiments. Simulations with different reactor configurations indicated relevant aspects for the design of solar reactors.

Influence of the Sol-Gel pH Process and Compact Film on the Efficiency of TiO2-Based Dye-Sensitized Solar Cells

The influence of pH during hydrolysis of titanium(IV) isopropoxide on the morphological and electronic properties of TiO2 nanoparticles prepared by the sol-gel method is investigated and correlated to the photoelectrochemical parameters of dye-sensitized solar cells (DSCs) based on TiO2 films. Nanoparticles prepared under acid pH exhibit smaller particle size and higher surface area, which result in higher dye loadings and better short-circuit current densities than DSCs based on alkaline TiO2-processed films. On the other hand, the product of charge collection and separation quantum yields in films with TiO2 obtained by alkaline hydrolysis is c. a. 27% higher than for the acid TiO2 films. The combination of acid and alkaline TiO2 nanoparticles as mesoporous layer in DSCs results in a synergic effect with overall efficiencies up to 6.3%, which is better than the results found for devices employing one of the nanoparticles separately. These distinct nanoparticles can be also combined by using the layer-by-layer technique (LbL) to prepare compact TiO2 films applied before the mesoporous layer. DSCs employing photoanodes with 30 TiO2 bilayers have shown efficiencies up to 12% higher than the nontreated photoanode ones. These results can be conveniently used to develop optimized synthetic procedures of TiO2 nanoparticles for several dye-sensitized solar cell applications.

Identification of bacteria in drinking and purified water during the monitoring of a typical water purification system

Abstract Background A typical purification system that provides purified water which meets ionic and organic chemical standards, must be protected from microbial proliferation to minimize cross-contamination for use in cleaning and preparations in pharmaceutical industries and in health environments. Methodology Samples of water were taken directly from the public distribution water tank at twelve different stages of a typical purification system were analyzed for the identification of isolated bacteria. Two miniature kits were used: (i) identification system (api 20 NE, Bio-Mérieux) for non-enteric and non-fermenting gram-negative rods; and (ii) identification system (BBL crystal, Becton and Dickson) for enteric and non-fermenting gram-negative rods. The efficiency of the chemical sanitizers used in the stages of the system, over the isolated and identified bacteria in the sampling water, was evaluated by the minimum inhibitory concentration (MIC) method. Results The 78 isolated colonies were identified as the following bacteria genera: Pseudomonas, Flavobacterium and Acinetobacter. According to the miniature kits used in the identification, there was a prevalence of isolation of P. aeruginosa 32.05%, P. picketti (Ralstonia picketti) 23.08%, P. vesiculares 12.82%,P. diminuta 11.54%, F. aureum 6.42%, P. fluorescens 5.13%, A. lwoffi 2.56%, P. putida 2.56%, P. alcaligenes 1.28%, P. paucimobilis 1.28%, and F. multivorum 1.28%. Conclusions We found that research was required for the identification of gram-negative non-fermenting bacteria, which were isolated from drinking water and water purification systems, since Pseudomonas genera represents opportunistic pathogens which disperse and adhere easily to surfaces, forming a biofilm which interferes with the cleaning and disinfection procedures in hospital and industrial environments.

The antimicrobial effect of new and conventional endodontic irrigants on intra-orally infected dentin

Objectives. To evaluate if the incorporation of antimicrobial compounds to chelating agents or the use of chelating agents with antimicrobial activity as 7% maleic acid and peracetic acid show similar disinfection ability in comparison to conventional irrigants as sodium hypochlorite or iodine potassium iodide against biofilms developed on dentin. Materials and methods. The total bio-volume of live cells, the ratio of live cells and the substratum coverage of dentin infected intra-orally and treated with the irrigant solutions: MTAD, Qmix, Smear Clear, 7% maleic acid, 2% iodine potassium iodide, 4% peracetic acid, 2.5% and 5.25% sodium hypochlorite was measured by using confocal microscopy and the live/dead technique. Five samples were used for each irrigant solution. Results. Several endodontic irrigants containing antimicrobials as clorhexidine (Qmix), cetrimide (Smear Clear), maleic acid, iodine compounds or antibiotics (MTAD) lacked an effective antibiofilm activity when the dentin was infected intra-orally. The irrigant solutions 4% peracetic acid and 2.5–5.25% sodium hypochlorite decrease significantly the number of live bacteria in biofilms, providing also cleaner dentin surfaces (p < 0.05). Conclusions. Several chelating agents containing antimicrobials could not remove nor kill significantly biofilms developed on intra-orally infected dentin, with the exception of sodium hypochlorite and 4% peracetic acid. Dissolution ability is mandatory for an appropriate eradication of biofilms attached to dentin.

Micro-organismos da subclasse Coccidia: resistência e implicações para o processamento de materiais de assistência à saúde

Este estudo teórico propõe uma reflexão sobre a resistência intrínseca da subclasse Coccidia, particularmente o gênero Cryptosporidium, considerado como um agente potencialmente patogênico para pacientes imunocomprometidos, e suas repercussões na prática assistencial. Atualmente, as diretrizes internacionais e nacionais aprovam como procedimento seguro a desinfecção química de alto nível de endoscópios digestivos, após sua limpeza. No entanto, estudos evidenciaram que micro-organismos da subclasse Coccidia, especificamente o Cryptosporidium, responsável por infecção entérica, são mais resistentes que as micobactérias e não são inativados pelos desinfetantes químicos de alto nível, exceto pelo Peróxido de Hidrogênio a 6% e 7,5%, formulação ainda não disponível no Brasil. Conclui-se que a legislação deve incluir este agente entre os micro-organismos teste para aprovação de desinfetantes químicos de alto nível e que as autoridades sanitárias devem se esforçar para garantir que os estabelecimentos de assistência à saúde tenham acesso a produtos eficazes contra o Cryptosporidium.

Remoção de biofilme em canais de endoscópios: avaliação de métodos de desinfecção atualmente utilizados

Estudo experimental laboratorial que comparou a ação de cinco métodos de desinfecção na remoção de biofilme em endoscópios gastrintestinais. Foram utilizados como corpos de prova tubos novos transparentes de politetrafluoretileno (Teflon®) simulando os canais flexíveis dos endoscópios. Após limpeza prévia os tubos foram contaminados intencionalmente com Pseudomonas aeruginosa para formação de biofilme e submetidos à desinfecção. Como resultado, nenhum deles removeu 100% dos biofilmes. O que mais removeu fisicamente o biofilme foi o glutaraldeído 2% em processadora automática, provavelmente justificado pela dupla limpeza, já que o equipamento conta com essa fase no início do seu ciclo. O método que se mostrou menos eficiente para remoção de biofilme e outros resíduos foi água eletrolítica ácida. Esses resultados sugerem que a limpeza é mais impactante na remoção de biofilmes do que a desinfecção consecutiva, uma vez que o glutaraldeído, desinfetante da máquina que se mostrou mais eficiente, é um fixador de resíduos orgânicos.

Influence of apical foramen lateral opening and file size on cemental canal instrumentation

Since instrumentation of the apical foramen has been suggested for cleaning and disinfection of the cemental canal, selection of the file size and position of the apical foramen have challenging steps. This study analyzed the influence of apical foramen lateral opening and file size can exert on cemental canal instrumentation. Thirty-four human maxillary central incisors were divided in two groups: Group 1 (n=17), without flaring, and Group 2 (n=17), with flaring with LA Axxess burs. K-files of increasing diameters were progressively inserted into the canal until binding at the apical foramen was achieved and tips were visible and bonded with ethyl cyanoacrylate adhesive. Roots/files set were cross-sectioned 5 mm from the apex. Apices were examined by scanning electron microscopy at ×140 and digital images were captured. Data were analyzed statistically by Student’s t test and Fisher’s exact test at 5% significance level. SEM micrographs showed that 19 (56%) apical foramina emerged laterally to the root apex, whereas 15 (44%) coincided with it. Significantly more difficulty to reach the apical foramen was noted in Group 2. Results suggest that the larger the foraminal file size, the more difficult the apical foramen instrumentation may be in laterally emerged cemental canals.

Effect of photodynamic therapy with different formulations of methylene blue in teeth contaminated by Enterococcus faecalis

The aim of this study was to compare the disinfection of dentine using photodynamic therapy with methylene blue in different formulations. Thirty bovine teeth roots were autoclaved and incubated with a suspension of Enterococcus faecalis. The specimen were randomly divided into three groups: G1, the roots were filled with 10 mM methylene blue dissolved in water; G2, the roots were filled with 10 mM methylene blue dissolved in a mixture of glycerol: ethanol: water; G3, roots filled with 100 mM methylene blue dissolved in water. The groups were irradiated with a 660 nm diode laser with an output power of 100 mW for 4 min, energy density of 850 J/cm2 and after this procedure, the sensitizer was removed and microbial samples were collected from within the root canals. The samples were plated on mEnterococcus to count the colony-forming units (CFU/mL). The means were: Group 1=513×103, Group 2=1431×103 and Group 3=2.96×103. The statistical analysis detected higher disinfection achieved by G3 when compared with groups G1 and G2, and no significant difference between the groups G1 and G2 (P>0.05). The increase of the concentration of methylene blue dye achieved higher disinfection in photodynamic therapy.

Copper(I) phenanthroline complexes and supramolecular systems containing fullerenes: Photophysics, photochemistry and potential applications in sustainable energy technologies.

Chemistry can contribute, in many different ways to solve the challenges we are facing to modify our inefficient and fossil-fuel based energy system. The present work was motivated by the search for efficient photoactive materials to be employed in the context of the energy problem: materials to be utilized in energy efficient devices and in the production of renewable electricity and fuels. We presented a new class of copper complexes, that could find application in lighting techhnologies, by serving as luminescent materials in LEC, OLED, WOLED devices. These technologies may provide substantial energy savings in the lighting sector. Moreover, recently, copper complexes have been used as light harvesting compounds in dye sensitized photoelectrochemical solar cells, which offer a viable alternative to silicon-based photovoltaic technologies. We presented also a few supramolecular systems containing fullerene, e.g. dendrimers, dyads and triads.The most complex among these arrays, which contain porphyrin moieties, are presented in the final chapter. They undergo photoinduced energy- and electron transfer processes also with long-lived charge separated states, i.e. the fundamental processes to power artificial photosynthetic systems.

Rastertunnelmikroskopie kombiniert mit optischen Methoden und ihre Anwendung für opto-elektronische Experimente an nanoskopischen Strukturen

Die vorliegende Arbeit untersucht mittels lichtunterstützter Tunnelmikroskopie (STM) den Elektronentransport in farbstoffbedeckten, nanoporösen TiO2-Schichten, die in photoelektrochemischen Solarzellen eingesetzt werden. Transportrelevante Eigenschaften wie die elektronische Zustandsdichte sowie lichtinduzierte Vorgänge wie der Aufbau einer lichtinduzierten Oberflächenladung und lokale Photoströme werden ortsaufgelöst gemessen. Für einen möglichen Einsatz in lichtunterstützter Tunnelmikroskopie werden desweiteren Gold-Nanopartikel auf einer Amino-Hexanthiol-Monolage auf Coulomb-Blockaden untersucht. Den zweite Schwerpunkt stellen methodische Arbeiten zur Messung optischer Nahfelder in STM-Experimenten dar. Erstens sollen die Vorteile von Apertur- und aperturloser optischer Rasternahfeld-Mikroskopie mit komplett metallisierten Faserspitzen verbunden werden, die durch die Faser beleuchtet werden. Es gelingt nicht, theoretisch vorhergesagte hohe optische Auflösungen zu bestätigen. Zweitens werden transparente Spitzen aus Sb-dotiertem Zinnoxid erfolgreich als Tunnelspitzen getestet. Die Spitzen ermöglichen STM-Elektrolumineszenz-Experimente zur Charakterisierung optischer Nahfelder, ohne diese durch eine metallische Spitze zu beeinträchtigen. In einer STM-Studie wird das Selbstorganisations-Verhalten von Oktanthiol und Oktandithiol auf Au(111) aus Ethanol untersucht. Bei geringer relativer Konzentration der Dithiole (1:2000), bildet sich eine Phase liegender Dithiole, deren Ordnung durch die Präsenz der Oktanthiole katalysiert wird. Schließlich wird ein als 'dynamische Tunnelmikroskopie' bezeichneter Modus für die Tunnelmikroskopie in elektrisch leitfähiger Umgebung erfolgreich getestet, der zur Unterdrückung des elektrochemischen Leckstromanteils die Ableitung des Stroms nach dem Abstand als STM-Abstandssignal verwendet.

Vancomycin-resistente Enterokokken (VRE) bei Patienten und in der aquatischen Umwelt

Vancomycin-resistente Enterokokken (VRE) treten als Erreger von nosokomialen Infektionen immer häufiger auf und schränken die Therapiemöglichkeiten deutlich ein. In den eigenen Untersuchungen wurde das Vorkommen von Vancomycin-resistenten Enterococcus faecium (VREf) bei Patienten und in der aquatischen Umwelt (Abwasser und Oberflächenwasser) über einen Zeitraum von sechs Jahren (2004 bis 2009) untersucht. Eine Genotypisierung mittels Pulsfeld-Gelelektrophorese (PFGE) von 294 VREf sollte Aufschluss über genetische Verwandtschaften geben. rnEs konnte gezeigt werden, dass VREf in der aquatischen Umwelt weit verbreitet sind. In Bezug auf ihre genetische Diversität zeigten sie ein breites Spektrum an Variabilität. Ebenso konnte im zeitlichen Auftreten von VREf-Typen eine Dynamik beobachtet werden, wodurch sich Veränderungen der Population mit zeitlichem Wechsel ergaben. Enge Verwandtschaften zwischen VREf von Patienten und VREf aus der aquatischen Umwelt konnten nachgewiesen werden. Für zwei VREf gelang der Nachweis des Eintrags in die aquatische Umwelt, von Patienten aus dem Krankenhaus als Eintragsquelle ausgehend, während Zeiten eines Ausbruchs mit nosokomialen Erregern auf den Stationen. rnZusätzlich zur VREf-Population wurden außerdem die Wirkungsweise und Effizienz einer Elektroimpulsanlage untersucht, um ein zukunftsorientiertes Verfahren zur Desinfektion von bakteriell belasteten Abwässern zu entwickeln. Weiterführend wurde getestet, inwiefern sich verschiedene klinisch relevante VREf durch ein gepulstes elektrisches Feld abtöten lassen. rnEs konnte gezeigt werden, dass das synergistische Zusammenwirken des elektrischen Feldes und der Prozesstemperatur die Höhe der Keimzahlreduktion der Enterokokken beeinflussen. Dabei wurde eine isolatabhängige Elektroresistenz der VREf gegenüber gepulsten elektrischen Feldern bewiesen. Die untersuchten VREf ließen sich, im Gegensatz zu einem Vancomycin-sensiblen Stamm, nicht effizient durch die Elektroimpulsanlage abtöten, was den praktischen Einsatz einer solchen Elektroimpulsanlage als wirkungsvolles Desinfektionsverfahren in Frage stellte.