Data protection by design in the e-health care sector: theoretical and applied perspectives

In the digital age, e-health technologies play a pivotal role in the processing of medical information. As personal health data represents sensitive information concerning a data subject, enhancing data protection and security of systems and practices has become a primary concern. In recent years, there has been an increasing interest in the concept of Privacy by Design, which aims at developing a product or a service in a way that it supports privacy principles and rules. In the EU, Article 25 of the General Data Protection Regulation provides a binding obligation of implementing Data Protection by Design technical and organisational measures. This thesis explores how an e-health system could be developed and how data processing activities could be carried out to apply data protection principles and requirements from the design stage. The research attempts to bridge the gap between the legal and technical disciplines on DPbD by providing a set of guidelines for the implementation of the principle. The work is based on literature review, legal and comparative analysis, and investigation of the existing technical solutions and engineering methodologies. The work can be differentiated by theoretical and applied perspectives. First, it critically conducts a legal analysis on the principle of PbD and it studies the DPbD legal obligation and the related provisions. Later, the research contextualises the rule in the health care field by investigating the applicable legal framework for personal health data processing. Moreover, the research focuses on the US legal system by conducting a comparative analysis. Adopting an applied perspective, the research investigates the existing technical methodologies and tools to design data protection and it proposes a set of comprehensive DPbD organisational and technical guidelines for a crucial case study, that is an Electronic Health Record system.

Irrigation and drainage canals role for plant diversity and nature conservation

Aims: With this research, we wanted to investigate and promote the conservation of biodiversity in the network of drainage canals of the Po Valley Study area: The canal network of Bologna plain, long more than 1150 km (Po Valley, North Italy) Methods: In Chapter II we analyzed the geographical patterns that characterize our transects, the land use of their upstream basins, the water quality at the closure points of their river basins. In Chapter III we described the plant communities with some ecological information and we also tested the effect of the canal size on the plant communities. In Chapter IV we described the relation beetween some functional traits of the plant species sampled and some environmental parameters Results: A total of 272 species were sampled in 118 transects. The plant communities of the drainage canals have been found to have a significant influence: the geographical pattern "proximity to protected areas", the class of land use "agrozootechnical settlements", and some water parameters. The analysis of the parameter "canal depth" indicated a significant distinction between small and large canals based on plant communities. The functional composition of the plant communities was affected by the bank aspect, the inclusion/exclusion from the protected areas and the upstream basin land uses. Moreover, the functional groups of species responded differently to environmental drivers, water quality gradients and were influenced by a combination of environmental stresses Conclusions: This research confirms the key role of the canals network in sustaining the plant richness in oversimplified landscapes. Considering the fragility of the floodplains and the global warming that is taking place, it is necessary to rethink the role of irrigation canals and their plant communities in the near future. This work reinforces the belief that long-term sampling plans and greater knowledge about canal management practices are needed

Design, development and guidance of the Airborne’s quadrotor

The main goal of the Airborne project is to develop, at technology readiness level 8 (TRL8), a few selected robotic aerial technologies for quick localization of victims by avalanches by equipping drones with two forefront sensors used in SAR operations in case of avalanches, namely the ARVA and RECCO. This thesis focuses on the design, development, and guidance of the TRL8 quadrotor developed during the project. We present and describe the design method that allowed us to obtain an EMI shielded UAV capable of integrating both RECCO and ARVA sensors. Besides, is presented the avionics and power train design and building procedure in order to obtain a modular UAV frame that can be easily carried by rescuers and achieves all the performance benchmarks of the project. Additionally, in addition to the onboard algorithms, a multivariate regressive convolutional neural network whose goal is the localization of the ARVA signal is presented. On guidance, the automatic flight procedure is described, and the onboard waypoint generator algorithm is presented. The goal of this algorithm is the generation and execution of an automatic grid pattern without the need to know the map in advance and without the support of a control ground station (CGS). Moreover, we present an iterative trajectory planner that does not need pre-knowledge of the map and uses Bézier curves to address optimal, dynamically feasible, safe, and re-plannable trajectories. The goal is to develop a method that allows local and fast replannings in case of an obstacle pop up or if some waypoints change. This makes the novel planner suitable to be applied in SAR operations. The introduction of the final version of the quadrotor is supported by internal flight tests and field tests performed in real operative scenarios by the Club Alpino Italiano (CAI).

Processi e pratiche di Innovazione Responsabile: il ruolo dell' Advanced Design nella trasformazione collaborativa dei territori

La ricerca indaga il rapporto tra Design e Innovazione Responsabile calandolo all’interno della relazione tra territorio e pratiche collaborative guidate dal design, ma anche legate al patrimonio culturale immateriale e a un sistema di conoscenza a quintupla elica. La necessità emergente di cura del futuro porta a rivedere il contesto del territorio come campo strumentale per la trasformazione degli individui e della comunità e a domandarsi in che modo il design possa supportare questo cambiamento, abilitando la produzione di conoscenza collaborativa. La ricerca parte dal dimostrare come il modello di innovazione recentemente proposto dalla Comunità Europea attraverso il concetto di Responsible Research Innovation (RRI), poi ripreso nella nozione di Responsible Innovation (RI), sia un campo aperto e responsivo: se integrato con altre discipline, in particolare con il design, può supportare lo sviluppo di processi, politiche, prodotti, servizi e comportamenti che rispettino la relazione tra società, ambiente, identità individuale e collettiva e i ritmi ad essi connessi. Partendo dal contesto sopra descritto, ci si chiede come il design e il designer possano integrare le dimensioni RI nei processi di progettazione, per innovare in modo collaborativo i territori. Si individua quindi nell’Advanced Design la metodologia che, grazie alla sua natura anticipatrice, collaborativa, trasformativa, riesce a coniugarsi virtuosamente con l’approccio RI e supportare il cambiamento in atto. L’intersezione di questi elementi porta alla creazione del Modello Advanced Design per/con l’Innovazione Responsabile (ADIR): un sistema multidimensionale per gruppi di innovazione (quintupla elica) che hanno l’obiettivo di rigenerare in modo collaborativo e inclusivo i territori. L’esperienza sul campo ha confermato come la struttura del modello, formata da un corpus di semi-lavorati, permetta di creare un proprio ritmo, una compenetrazione tra azioni e forme progettuali volti a mantenere il senso di comunità e il coinvolgimento degli attori, a creare relazioni, a sviluppare una trasformazione continua.

Innovation in conceptual design of chemical processes

Nowadays, the chemical industry has reached significant goals to produce essential components for human being. The growing competitiveness of the market caused an important acceleration in R&D activities, introducing new opportunities and procedures for the definition of process improvement and optimization. In this dynamicity, sustainability is becoming one of the key aspects for the technological progress encompassing economic, environmental protection and safety aspects. With respect to the conceptual definition of sustainability, literature reports an extensive discussion of the strategies, as well as sets of specific principles and guidelines. However, literature procedures are not completely suitable and applicable to process design activities. Therefore, the development and introduction of sustainability-oriented methodologies is a necessary step to enhance process and plant design. The definition of key drivers as support system is a focal point for early process design decisions or implementation of process modifications. In this context, three different methodologies are developed to support design activities providing criteria and guidelines in a sustainable perspective. In this framework, a set of key Performance Indicators is selected and adopted to characterize the environmental, safety, economic and energetic aspects of a reference process. The methodologies are based on heat and material balances and the level of detailed for input data are compatible with available information of the specific application. Multiple case-studies are defined to prove the effectiveness of the methodologies. The principal application is the polyolefin productive lifecycle chain with particular focus on polymerization technologies. In this context, different design phases are investigated spanning from early process feasibility study to operative and improvements assessment. This flexibility allows to apply the methodologies at any level of design, providing supporting guidelines for design activities, compare alternative solutions, monitor operating process and identify potential for improvements.

Fighting child marriage in developing countries: design and development of a mobile application

Child marriage is still a great issue in developing countries and even if the interventions to prevent it are having results, they are not enough to eliminate the problem. Among the strategies that seem to work most to fight child marriage, there is the empowerment of girls with information combined with education of parents and community. As smartphones are more accessible year after year in developing countries, this thesis wants to investigate if a mobile app could be effective in fighting child marriage and which characteristics such an app should have. The research was organized in four phases and used design and creation and case study methodologies. Firstly, the literature was analyzed and an initial design was proposed. Secondly, expert interviews were performed to gain feedback on the proposed design, and afterwards prototype was built. Thirdly, a case study in the Democratic Republic of Congo (DRC) was performed to test the prototype, gaining insights and improvements through group interviews with 26 girls aged 15-19. Finally, a first version of the app was developed and a second phase of the case study was run in the DRC to understand if the girls were able to use the app. This phase included 14 girls of which 6 had participated in the prototype testing and used questionnaires as a data generation method. The app was built following the Principles for Digital Development. Even if this app is built based on the case study in DRC is modular and easily adaptable to other contexts as it is not content-specific. It was shown that is worth continuing to study this topic and it was defined a conceptual framework for designing learning apps for developing countries, in particular, to fight child, early, and forced marriage.

Physiological limitations in two sugarcane varieties under water suppression and after recovering

Increasing water scarcity and depleted water productivity in irrigated soils are inducing farmers to adopt improved varieties, such as those with high-capacity tolerance. The use of tolerant varieties of sugarcane might substantially avoid the decline of productivity under water deficit. This research aimed to evaluate the harmful effects of drought on the physiology of two sugarcane varieties (RB867515 and RB962962) during the initial development. Young plants were subjected to irrigation suspension until total stomata closure, and then rewatered. Significant reduction on stomatal conductance, transpiration, and net photosynthesis were observed. RB867515 showed a faster stomatal closure while RB962962 slowed the effects of drought on the gas exchanges parameters with a faster recovering after rewatering. Accumulation of carbohydrates, amino acids, proline, and protein in the leaves and roots of the stressed plants occurred in both varieties, substantially linked to reduction of the leaf water potential. Due to the severity of stress, this accumulation was not enough to maintain the cell turgor pressure, so relative water content was diminished. Water stress affected the contents of chlorophyll (a, b, and total) in both varieties, but not the levels of carotenoids. There was a significant reduction in dry matter under stress. In conclusion, RB962962 variety endured stressed conditions more than RB867515, since it slowed down the damaging effects of drought on the gas exchanges. In addition, RB962962 presented a faster recovery than RB867515, a feature that qualifies it as a variety capable of enduring short periods of drought without major losses in the initial stage of its development.

Methodology of a nationwide cross-sectional survey of prevalence and epidemiological patterns of hepatitis A, B and C infection in Brazil

Um inquérito de base populacional foi conduzido na população urbana de todas as capitais e do Distrito Federal no Brasil para fornecer informações sobre a prevalência de hepatites virais e fatores de risco, entre 2005 e 2009. Este artigo descreve o delineamento e a metodologia do estudo que envolveu a população com idade entre 5 e 19 anos para hepatite A e 10 a 69 anos para hepatite B e C. As entrevistas e amostras de sangue foram obtidas através de visitas domiciliares e a amostra selecionada a partir de uma amostragem estratificada em múltiplos estágios (por conglomerado) com igual probabilidade para cada domínio de estudo (região e faixa etária). Nacionalmente, 19.280 residências e ~31.000 indivíduos foram selecionados. O tamanho da amostra foi suficiente para detectar uma prevalência em torno de 0,1% e para avaliar os fatores de risco por região. A metodologia apresentou-se viável para distinguir entre diferentes padrões epidemiológicos da hepatite A, B e C. Estes dados serão de valia para a avaliação das políticas de vacinação e para o desenho de estratégias de controle.

ACCUMULATION AND TRANSLOCATION OF SILICON IN RICE AND BEAN PLANTS USING THE 30SI STABLE ISOTOPE

The 30Si silicon isotope stable was used for assessing the accumulation and translocation of Si in rice and bean plants grown in labeled nutritive solution. The isotopic silicon composition in plant materials was determined by mass spectrometry (IRMS) using the method based on SiF4 formation. Considering the total-Si added into nutritive solutions, the quantity absorbed by plants was near to 51% for rice and 15% for bean plants. The accumulated amounts of Si per plant were about 150g in rice and 8.6g in bean. Approximately 70% of the total-Si accumulated was found in leaves. At presented experimental conditions, the results confirmed that once Si is accumulated in the old parts of rice and bean plant tissues it is not redistributed to new parts, even when Si is not supplied to plants from nutritive solution.

Fractionation of Zn, Cd and Pb in a Tropical Soil After Nine-Year Sewage Sludge Applications

A long-term field experiment was carried out in the experiment farm of the Sao Paulo State University, Brazil, to evaluate the phytoavailability of Zn, Cd and Pb in a Typic Eutrorthox soil treated with sewage sludge for nine consecutive years, using the sequential extraction and organic matter fractionation methods. During 2005-2006, maize (Zea mays L.) was used as test plants and the experimental design was in randomized complete blocks with four treatments and five replicates. The treatments consisted of four sewage sludge rates (in a dry basis): 0.0 (control, with mineral fertilization), 45.0, 90.0 and 127.5 t ha(-1), annually for nine years. Before maize sowing, the sewage sludge was manually applied to the soil and incorporated at 10 cm depth. Soil samples (0-20 cm layer) for Zn, Cd and Pb analysis were collected 60 days after sowing. The successive applications of sewage sludge to the soil did not affect heavy metal (Cd and Pb) fractions in the soil, with exception of Zn fractions. The Zn, Cd and Pb distributions in the soil were strongly associated with humin and residual fractions, which are characterized by stable chemical bonds. Zinc, Cd and Pb in the soil showed low phytoavailability after nine-year successive applications of sewage sludge to the soil.

Reliability-based evaluation of design code provisions for circular concrete-filled steel columns

This paper presents an investigation of design code provisions for steel-concrete composite columns. The study covers the national building codes of United States, Canada and Brazil, and the transnational EUROCODE. The study is based on experimental results of 93 axially loaded concrete-filled tubular steel columns. This includes 36 unpublished, full scale experimental results by the authors and 57 results from the literature. The error of resistance models is determined by comparing experimental results for ultimate loads with code-predicted column resistances. Regression analysis is used to describe the variation of model error with column slenderness and to describe model uncertainty. The paper shows that Canadian and European codes are able to predict mean column resistance, since resistance models of these codes present detailed formulations for concrete confinement by a steel tube. ANSI/AISC and Brazilian codes have limited allowance for concrete confinement, and become very conservative for short columns. Reliability analysis is used to evaluate the safety level of code provisions. Reliability analysis includes model error and other random problem parameters like steel and concrete strengths, and dead and live loads. Design code provisions are evaluated in terms of sufficient and uniform reliability criteria. Results show that the four design codes studied provide uniform reliability, with the Canadian code being best in achieving this goal. This is a result of a well balanced code, both in terms of load combinations and resistance model. The European code is less successful in providing uniform reliability, a consequence of the partial factors used in load combinations. The paper also shows that reliability indexes of columns designed according to European code can be as low as 2.2, which is quite below target reliability levels of EUROCODE. (C) 2009 Elsevier Ltd. All rights reserved.

Ethanol production process from banana fruit and its lignocellulosic residues: Energy analysis

Tropical countries, such as Brazil and Colombia, have the possibility of using agricultural lands for growing biomass to produce bio-fuels such as biodiesel and ethanol. This study applies an energy analysis to the production process of anhydrous ethanol obtained from the hydrolysis of starch and cellulosic and hemicellulosic material present in the banana fruit and its residual biomass. Four different production routes were analyzed: acid hydrolysis of amylaceous material (banana pulp and banana fruit) and enzymatic hydrolysis of lignocellulosic material (flower stalk and banana skin). The analysis considered banana plant cultivation, feedstock transport, hydrolysis, fermentation, distillation, dehydration, residue treatment and utility plant. The best indexes were obtained for amylaceous material for which mass performance varied from 346.5 L/t to 388.7 L/t, Net Energy Value (NEV) ranged from 9.86 MJ/L to 9.94 MJ/L and the energy ratio was 1.9 MJ/MJ. For lignocellulosic materials, the figures were less favorable: mass performance varied from 86.1 to 123.5 L/t, NEV from 5.24 10 8.79 MJ/L and energy ratio from 1.3 to 1.6 MJ/MJ. The analysis showed, however, that both processes can be considered energetically feasible. (C) 2010 Elsevier Ltd. All rights reserved.

Energy and exergy analysis of ethanol production process from banana fruit

An alternative for ethanol production, is the use of vegetable waste, such as excess of banana production, that are evaluated in 2,400,000 t/year, which includes: residual banana fruit and lignocellulosic material. This paper analyzes the energetic and exergetic behavior to carry the process developed at laboratory scale to a plant processing of banana for the ethanol production, involving: growing and transport of the vegetable material, hydrolysis of banana fruit, sugar fermentation, ethanol distillation and utility plant. Finally, energy and exergy indicators are obtained. The results show a positive energy balance when banana fruit is used for ethanol production, but some process modification must be done looking for improving the exergetic efficiency in ethanol production.

Investigation of the mass transfer processes during the desalination of water containing phenol and sodium chloride by electrodialysis

Oxidation processes are used in wastewater treatment when conventional processes are not effective due to the presence of recalcitrant organic contaminants, like phenol. However, the presence of ionic compounds associated with organic pollutants may retard the oxidation. In this work the transport of species contained in an aqueous solution of phenol containing sodium chloride was evaluated in an electrodialysis (ED) system. An experimental study was carried out in which the influence of the process variables on the phenol loss and sodium chloride removal was investigated. Experiments were also performed without current, in order to determine the phenol transfer due to diffusion. The phenol and salt concentration variations in the ED compartments were measured over time, using dedicated procedures and an experimental design to determine the global characteristic parameters. A phenomenological approach was used to relate the phenol, salt and water fluxes with the driving forces (concentration and electric potential gradients). Under ED conditions, two contributions were pointed out for the phenol transport, i.e. diffusion and convection, this latter coming from the water flux due to electroosmosis related to the migration of salts. The fitting of the parameters of the transport equations resulted in good agreement with the experimental results over the range of conditions investigated. (c) 2008 Elsevier B.V. All rights reserved.

Inverse aerodynamic design applications using the MGM hybrid formulation

The well-known modified Garabedian-Mcfadden (MGM) method is an attractive alternative for aerodynamic inverse design, for its simplicity and effectiveness (P. Garabedian and G. Mcfadden, Design of supercritical swept wings, AIAA J. 20(3) (1982), 289-291; J.B. Malone, J. Vadyak, and L.N. Sankar, Inverse aerodynamic design method for aircraft components, J. Aircraft 24(2) (1987), 8-9; Santos, A hybrid optimization method for aerodynamic design of lifting surfaces, PhD Thesis, Georgia Institute of Technology, 1993). Owing to these characteristics, the method has been the subject of several authors over the years (G.S. Dulikravich and D.P. Baker, Aerodynamic shape inverse design using a Fourier series method, in AIAA paper 99-0185, AIAA Aerospace Sciences Meeting, Reno, NV, January 1999; D.H. Silva and L.N. Sankar, An inverse method for the design of transonic wings, in 1992 Aerospace Design Conference, No. 92-1025 in proceedings, AIAA, Irvine, CA, February 1992, 1-11; W. Bartelheimer, An Improved Integral Equation Method for the Design of Transonic Airfoils and Wings, AIAA Inc., 1995). More recently, a hybrid formulation and a multi-point algorithm were developed on the basis of the original MGM. This article discusses applications of those latest developments for airfoil and wing design. The test cases focus on wing-body aerodynamic interference and shock wave removal applications. The DLR-F6 geometry is picked as the baseline for the analysis.