Nitrification of high strength ammonia wastewtaer treatment - process selection is the major factor.

Biological nitrogen removal via the nitrite pathway in wastewater treatment is very important in Saving the cost of aeration and as an electron donor for denitrification. Wastewater nitrification and nitrite accumulation were carried out in a biofilm airlift reactor with autotrophic nitrifying biofilm. The biofilm reactor showed almost complete nitrification and most of the oxidized ammonium was present as nitrite at the ammonium load of 1.5 to 3.5 kg N/m3.d. Nitrite accumulation was stably achieved by the selective inhibition of nitrite oxidizers with free ammonia and dissolved oxygen limitation. Stable 100% conversion to nitrite could also be achieved even under the absence of free ammonia inhibition on nitrite oxidizers. Batch ammonium oxidation and nitrite oxidation with nitrite accumulating nitrifying biofilm showed that nitrite Oxidation was completely inhibited when free ammonia is higher than 0.2 mg N/L. However, nitrite oxidation activity was recovered as soon as the free ammonia concentration was below the threshold level when dissolved oxygen concentration was not the limiting factor. Fluorescence in situ hybridization analysis of cryosectioned nitrite accumulating nitrifying biofilm showed that the β-subclass of Proteobacteria, where ammonia oxidizers belong, was distributed outside the biofilm whereas the α-subclass of Proteobacteria, where nitrite oxidizers belong, was found mainly in the inner part of the biofilm. It is likely that dissolved oxygen deficiency or limitation in the inner part of the nitrifying biofilm, where nitrite oxidizers exist, is responsible for the complete shut down of the nitrite oxidizers activity under the absence of free ammonia inhibition.

Effect of time of harvest of budded virus on the selection of baculovirus FP mutants in cell culture

Rapid formation and selection of FP (few polyhedra) mutants occurs during serial passaging of Helicoverpa armigera nucleopolyhedrovirus (HaSNPV) in insect cell culture. The production of HaSNPV for use as biopesticides requires the passaging of the virus over a number of passages to produce enough virus inoculum for large-scale fermentation. During serial passaging in cell culture, FP mutants were rapidly selected, resulting in declined productivity and reduced potency of virus. Budded virus (BV) is usually harvested between 72 and 96 h postinfection (hpi) in order to obtain a high titer virus stock. In this study, the effect of tine of harvest (TOH) for BV on the selection rate of HaSNPV FP mutants during serial passaging was investigated. BV were harvested at different times postinfection, and each series was serially passaged for six passages. The productivity and percentage of FP mutants at each passage were determined. It was found that the selection of FP mutants can he reduced by employing an earlier TOH for BV. Serial passaging with BV harvested at 48 hpi showed a slower accumulation of FP mutants compared to that of BV harvested after 48 hpi. Higher cell specific yields were also maintained when BV were harvested at 48 hpi. When BV that were formed between 48 and 96 hpi were harvested and serially passaged, FP mutants quickly dominated the virus population. This suggests that the V formed and released between 48 and 96 hpi are most likely from FP mutant infected cells.

Elaboração e análise de extrato hidrossolúvel de gergelim (Sesamum indicum)

O objetivo do presente estudo foi elaborar e caracterizar um extrato hidrossolúvel à base de gergelim para ser usado como possível substituto do leite de vaca e extrato de soja. Foi proposto um modelo de cinética de absorção de água durante a etapa de maceração no qual estimou o tempo ideal de batimento do gergelim macerado e se essa etapa influencia no rendimento do produto. Posteriormente com o objetivo de saber a influência do tempo de batimento (0,45 min a 14,55 min) e a concentração do extrato (1,925% a 23,07%) foram avaliadas através de um delineamento composto central rotacional (DCCR), ou seja, um delineamento 22 incluindo 4 ensaios nas condições axiais e 5 repetições no ponto central, totalizando 13 experimentos. Para todos os ensaios do delineamento realizou-se análises de viscosidade, cor, sólidos solúveis totais e rendimento. As mesmas análises foram realizadas em amostras comerciais de leite de vaca e extrato hidrossolúvel de soja com o intuito de comparação. Após a realização dessa etapa foi possível à seleção de algumas amostras para elaboração do extrato hidrossolúvel de gergelim e então realizou-se análises físico-químicas (proteína, cinzas, lipídios, carboidratos) e determinou-se a capacidade antioxidante por ABTS e teor de compostos fenólicos de tais amostras. Quanto à análise de rendimento não houve diferença significativa da quantidade de extrato obtido em diferentes temperaturas de maceração pelo teste de Tukey (p> 0,05). O DCCR foi realizado no programa Statistica e selecionaram-se os ensaios 1, 2, 6, 7, PC (ponto central) que foram as amostras que mais se assemelharam com as amostras comerciais estudadas. Nessas amostras realizou-se as análises físico-químicas além de capacidade antioxidante e compostos fenólicos. O conteúdo de sólidos totais na amostra 6 foi superior as demais amostras, diferindo estatisticamente das demais amostras (p> 0,05). Já para o teor de lipídios, cinzas e proteínas encontrados nas amostras 6 e PC foram maiores que as demais amostras, enquanto a amostra 7 exibiu o menor teor de lipídios e proteínas, considerando que o teor de cinzas das amostras 1, 2 e 7 foram estatisticamente iguais. O teor de carboidratos calculado por diferença foi superior nas amostras 1, 2 e 7 e com o menor valor na amostra 6. Os valores de capacidade antioxidante e compostos fenólicos não se diferenciaram estatisticamente entre si ao nível de 5% de probabilidade. Concluiu-se portanto que a etapa de maceração não influenciou no rendimento do produto final. A partir das análises físico-químicas pode-se concluir que o extrato hidrossolúvel de gergelim em determinadas amostras apresentou um melhor desempenho quanto ao valor nutricional comparado ao extrato de soja.

Cidade-paisagem : novas perspectivas sobre a preservação da paisagem urbana no Brasil

The edification of the landscape in the scientific and social field, in speech as in the method, is taken in this study as a complex process, from which were developed relationships of dominance on the perception of space, which persist strongly consolidated, since the genesis of the conceptual practice till its actual praxis. Historically, the landscape studies took place slowly, immersed in many questions, in face of the multiplicity of meanings that the concept offers. In the psyche, the notion of landscape is present since a long time ago, as an unconscious human being practice, even before any ideological hypothesis formulation. However its materialization in the social conscious will come only from painting, and specially with the perspective, through the technicity of the view, at first wandering the infinity, now ordained in a frame‟. Since then, the landscape is perceived according to the order of the view, as the equivalent of nature and beauty, assuming at the same time, an important symbolic value, since it is linked to mnemonic and subjective processes that the being build with the territory. The domain on this space-cognitive experience, characteristic of the contemporary, consolidates in the social imaginary, building consensus on the landscape, whose aesthetic references make a cultural appeal, very pertinent to the actual capitalist dynamics of production the space worldwide, mainly of the spectacle and commodification of cities promoted by the city marketing. In Brazil, this consensual ideology of the landscape surpass the social imaginary and also dominates the political imaginary, whereas the main instrument for preserving the landscape, Decree-law 25, from November 30, 1937, and its limit to those of exceptional value or remarkable feature. The analysis of the processes for putting under governmental trust for inscription of goods by the landscape value, reveals the dominant, if not exclusive, adoption of selection criteria related to aesthetic aspects. Abstain, therefore, from what the nation considers patrimony , other landscapes that, besides not having, at first, remarkable aesthetic value, play a crucial role as an inheritance from ancestor relations between man and space and pre- existing condition for the same present and future relations. From this historical background, the research seeks to transfer into contemporaneity, the ideological analysis of the concept and its relation with the building of the landscape in the collective imaginary, in order to recognize, in current practices to landscape preservation, as much this genesis, rooted in aesthetics, remains strongly consolidated, feeding the current dynamics of consumption and commodification of the city. Therefore, as preliminary conclusion, one can state that the identification of landscapes of different value, especially aesthetic, maintains and intensify the treatment of the city as an object, a standard‟ commodity to be sold / traded on the world market, in detriment of its recognition as a dynamic process that, even though inserted in the global context, develops specificifities and peculiarities, inherent to the production of space, as Lefebvre preconizes, that is, to the production of life, social product , as characteristic, dissent generator

Integrating environmental and economic life cycle analysis in product development: a material selection case study

Purpose Achieving sustainability by rethinking products, services and strategies is an enormous challenge currently laid upon the economic sector, in which materials selection plays a critical role. In this context, the present work describes an environmental and economic life cycle analysis of a structural product, comparing two possible material alternatives. The product chosen is a storage tank, presently manufactured in stainless steel (SST) or in a glass fibre reinforced polymer composite (CST). The overall goal of the study is to identify environmental and economic strong and weak points related to the life cycle of the two material alternatives. The consequential win-win or trade-off situations will be identified via a Life Cycle Assessment/Life Cycle Costing (LCA/LCC) integrated model. Methods The LCA/LCC integrated model used consists in applying the LCA methodology to the product system, incorporating, in parallel, its results into the LCC study, namely those of the Life Cycle Inventory (LCI) and the Life Cycle Impact Assessment (LCIA). Results In both the SST and CST systems the most significant life cycle phase is the raw materials production, in which the most significant environmental burdens correspond to the Fossil fuels and Respiratory inorganics categories. The LCA/LCC integrated analysis shows that the CST has globally a preferable environmental and economic profile, as its impacts are lower than those of the SST in all life cycle stages. Both the internal and external costs are lower, the former resulting mainly from the composite material being significantly less expensive than stainless steel. This therefore represents a full win-win situation. As a consequence, the study clearly indicates that using a thermoset composite material to manufacture storage tanks is environmentally and economically desirable. However, it was also evident that the environmental performance of the CST could be improved by altering its End-of-Life stage. Conclusions The results of the present work provide enlightening insights into the synergies between the environmental and the economic performance of a structural product made with alternative materials. Further, they provide conclusive evidence to support the integration of environmental and economic life cycle analysis in the product development processes of a manufacturing company, or in some cases even in its procurement practices.

A practical framework for the generation and selection of strategic plans of action, The relevance of timeframe considerations and a systems thinking approach

The paper proposes a methodology especially focused on the generation of strategic plans of action, emphasizing the relevance of having a structured timeframe classification for the actions. The methodology explicitly recognizes the relevance of long-term goals as strategic drivers, which must insure that the complex system is capable to effectively respond to changes in the environment. In addition, the methodology employs engineering systems techniques in order to understand the inner working of the system and to build up alternative plans of action. Due to these different aspects, the proposed approach features higher flexibility compared to traditional methods. The validity and effectiveness of the methodology has been demonstrated by analyzing an airline company composed by 5 subsystems with the aim of defining a plan of action for the next 5 years, which can either: improve efficiency, redefine mission or increase revenues.

Criteria for ERP selection using an AHP approach

Information systems are a foundation key element of modern organizations. Quite often, chief executive officers and managers have to decide about the acquisition of new software solution based in an appropriated set of criteria. Analytic Hierarchy Process (AHP) is one technique used to support that kind of decisions. This paper proposes the application of AHP method to the selection of ERP (Enterprise Resource Planning) systems, identifying the set of criteria to be used. A set of criteria was retrieved from the scientific literature and validated through a survey-based approach.

Simultaneous selection in progenies of yellow passion fruit using selection indices

This study aimed to evaluate the efficiency of simultaneous selection (selection indices) using estimated genetic gains in yellow passion fruit and to make a comparison between the methodologies of Mulamba & Mock and Elston. The study was conducted with 26 sib progenies of yellow passion fruit for intrinsic production characteristics including fruit number, fruit mass, fruit length and diameter, and for the fruit characteristics skin thickness, soluble solids and acidity. Two methodologies were applied: first, in the joint analysis of fruit characteristics and of intrinsic production characteristics in a single phase of selection; and second, in the analysis in two phases, in which priority was given to the intrinsic production characteristics in the first phase, and later, in the second phase, the best fruit characteristics were chosen among the progenies of the first phase. The analysis of variance was applied to the data to detect genetic variability among progenies. The Elston's selection indice was unable to provide distribution of genetic gains consistent with the purposes of the study, as it selected a single progeny of passion fruit. However, the index based on the sum of ranks of Mulamba & Mock was more suitable, as it provided a balanced distribution of gains, selecting a larger number of progenies. The methodology of selection using indices is advantageous in passion fruit, since it contributes to higher genetic gains for all the traits evaluated, and the selection in a single phase was proved efficient for progeny selection.

Automatic segmentation and 3D feature extraction of protein aggregates in Caenorhabditis Elegans

In the last years, it has become increasingly clear that neurodegenerative diseases involve protein aggregation, a process often used as disease progression readout and to develop therapeutic strategies. This work presents an image processing tool to automatic segment, classify and quantify these aggregates and the whole 3D body of the nematode Caenorhabditis Elegans. A total of 150 data set images, containing different slices, were captured with a confocal microscope from animals of distinct genetic conditions. Because of the animals’ transparency, most of the slices pixels appeared dark, hampering their body volume direct reconstruction. Therefore, for each data set, all slices were stacked in one single 2D image in order to determine a volume approximation. The gradient of this image was input to an anisotropic diffusion algorithm that uses the Tukey’s biweight as edge-stopping function. The image histogram median of this outcome was used to dynamically determine a thresholding level, which allows the determination of a smoothed exterior contour of the worm and the medial axis of the worm body from thinning its skeleton. Based on this exterior contour diameter and the medial animal axis, random 3D points were then calculated to produce a volume mesh approximation. The protein aggregations were subsequently segmented based on an iso-value and blended with the resulting volume mesh. The results obtained were consistent with qualitative observations in literature, allowing non-biased, reliable and high throughput protein aggregates quantification. This may lead to a significant improvement on neurodegenerative diseases treatment planning and interventions prevention

Prediction of genetic gain from selection indices for disease resistance in papaya hybrids

In order to select superior hybrids for the concentration of favorable alleles for resistance to papaya black spot, powdery mildew and phoma spot, 67 hybrids were evaluated in two seasons, in 2007, in a randomized block design with two replications. Genetic gains were estimated from the selection indices of Smith & Hazel, Pesek & Baker, Williams, Mulamba & Mock, with selection intensity of 22.39%, corresponding to 15 hybrids. The index of Mulamba & Mock showed gains more suitable for the five traits assessed when it was used the criterion of economic weight tentatively assigned. Together, severity of black spot on leaves and on fruits, characteristics considered most relevant to the selection of resistant materials, expressed percentage gain of -44.15%. In addition, there were gains for other characteristics, with negative predicted selective percentage gain. The results showed that the index of Mulamba & Mock is the most efficient procedure for simultaneous selection of papaya hybrid resistant to black spot, powdery mildew and phoma spot.

Agronomic performance of 27 cocoa progenies and plant selection based on productivity, self-compatibility and disease resistance

The objective of the present work was to evaluate 27 progenies of cocoa crosses considering the agronomic traits and select F1 plants within superior crosses. The experiment was installed in March 2005, in the Experimental Station Joaquim Bahiana (ESJOB), in Itajuipe, Bahia. The area of the experiment is of approximately 3 ha, with a total of 3240 plants. Thirteen evaluations of vegetative brooms, five of cushion brooms and 15 of number of pods per plant were accomplished. Thirty pollinations were made for each selected plant to test for self-compatibility. The production, based on the number of pods per plant, and resistance to witches´ broom indicated CEPEC 94 x CCN 10, RB 39 x CCN 51 and CCN 10 x VB 1151 as superior progenies. All selections tested were self-compatible. The analyses of progenies and individual tree data, associated to visual field observations, allowed the selection of 17 plants which were included in a network of regional tests to determine the phenotypic stability.

Selection of common bean lines with high grain yield and high grain calcium and iron concentrations

Genetic improvement of common bean nutritional quality has advantages in marketing and can contribute to society as a food source. The objective of this study was to evaluate the genetic variability for grain yield, calcium and iron concentrations in grains of inbred common bean lines obtained by different breeding methods. For this, 136 F7 inbred lines were obtained using the Pedigree method and 136 F7 inbred lines were obtained using the Single-Seed Descent (SSD) method. The lines showed genetic variability for grain yield, and concentrations of calcium and iron independently of the method of advancing segregating populations. The Pedigree method allows obtaining a greater number of lines with high grain yield. Selection using the SSD method allows the identification of a larger number of lines with high concentrations of calcium and iron in grains. Weak negative correlations were found between grain yield and calcium concentration (r = -0.0994) and grain yield and iron concentration (r = -0.3926). Several lines show genetic superiority for grain yield and concentrations of calcium and iron in grains and their selection can result in new common bean cultivars with high nutritional quality.

Loneliness in Middle and Old Age

Purpose of the research: (a) To identify the degree of much loneliness reported in the Portuguese population over 50 years of age and (b) test whether loneliness can be predicted by socio-demographic, health related or social characteristic of the sample other than age. Materials and methods: 1174 late middle age and older adults were interviewed face to face by different interviewers across the country; after the informed consent was signed, we asked the participants several socio-demographic and health-related questions; finally we asked ‘‘How often do you feel lonely?’’ and participants responded according to a five point Likert scale. Principal results: The results showed that 12% of participants reporting feeling lonely often or always, whereas 40% reporting never feeling lonely. The remaining 48% self-reported they felt lonely seldom or sometimes. Additionally, results show that, when taken together, variables such as marital status, type of housing, residence settings, health conditions, social satisfaction, social isolation, lack of interest, transportation, and age were predictors of loneliness. Major conclusions: (1) The association of loneliness with advanced age has been greatly exaggerated by mass media and common sense; (2) But although our findings did not confirm the most alarmist views, the 12% of older adults reporting that they are feeling lonely always or often should be cause for attention and concern. It is necessary to understand the meaning, reasons and level of suffering implied on those feelings of loneliness. (3) Our findings suggest that it makes no sense to construe age as a singular feature or cause for feelings of loneliness. Instead, age and also a number of other features combine to predict feelings of loneliness. But even with our predictor variables there was a substantial of variance left unexplained. Therefore it is necessary to continue exploring how feelings of loneliness arise from the experience of living and how they can be changed.

Selection of anthracnose resistant common beans using detached leaves in partially controlled environment

The objectives of this study were to evaluate the possibility of selecting anthracnose resistant common bean plants using detached primary leaves in partially controlled environment of a greenhouse and identify differences in the reaction of genotypes to anthracnose. The common bean cultivars Ouro Negro, OuroVermelho, ManteigãoFosco 11, Rudá, Rudá-R, VP8, BRSMG Madrepérola, Pérola, MeiaNoite and BRSMG Talismãwere characterizedfor resistance to the races 65, 81 and 453 of Colletotrichum lindemuthianum and the method of detached primary leaves was compared to the method with the traditional inoculation of plants at the phenological stage V2. The lines Rudá, Rudá-R and Pérola were inoculated with the races 65 and 453 of C. lindemuthianum, aiming to assess the rate of coincidence of anthracnose severity by both inoculation methods. In general, the two methods presented similar results for the reaction of the cultivars. The use of detached primary leaves of common bean plants in the partially controlled environment was feasible for selection of plants resistant to anthracnose and has the advantages of low-needed infrastructure and reduction of resources, space and time.