Femtosecond laser pulse irradiation of Sb-rich AgInSbTe films: Scanning electron microscopy and atomic force microscopy investigations

The single-layer and multilayer Sb-rich AgInSbTe films were irradiated by a single femtosecond laser pulse with the duration of 120 fs. The morphological feature resulting from the laser irradiation have been investigated by scanning electron microscopy and atom force microscopy. For the single-layer film, the center of the irradiated spot is a dark depression and the border is a bright protrusion; however, for the multilayer film, the center morphology changes from a depression to a protrusion as the energy increases. The crystallization threshold fluence of the single-layer and the multilayer films is 46.36 mJ/cm(2), 63.74 mJ/cm(2), respectively.

Direct writing computer-generated holograms on metal film by an infrared femtosecond laser

Writing computer-generated holograms has been achieved by using near infrared femtosecond laser selective ablation of metal film deposited on glass substrate. The diffraction features with data reconstruction of fabricated computer-generated holograms were evaluated. Both transmission and reflection holograms can be fabricated in a single process. The process required no mask, no pre- or post-treatment of the substrate. (C) 2005 Optical Society of America.

飞秒激光烧蚀玻璃基质金属薄膜直写衍射光栅

提出了一种新的制备光栅的方法，利用800nm的飞秒激光扫描蒸镀在石英玻璃衬底表面的金薄膜，通过烧蚀金薄膜在衬底表面形成衍射光栅。用波长为532nm的激光照射光栅，测量其一级衍射效率，测得的衍射效率最高为6．98％。通过改变激光扫描速度、激光功率、光栅周期等实验参数研究其对制备的光栅的一级衍射效率的影响，结果表明，降低激光扫描速度，减小光栅周期，或增加激光功率都能提高制备光栅的一级衍射效率。

Investigation of damage threshold to TiO2 coatings at different laser wavelength and pulse duration

Laser-induced damages to TiO2 single layers and TiO2/SiO2 high reflectors at laser wavelength of 1064 nm, 800 run, 532 urn, and pulse width of 12 ns, 220 ps, 50 fs, 8 ns are investigated. All films are prepared by electron beam evaporation. The relations among microstructure, chemical composition, optical properties and laser-induced damage threshold (LIDT), have been researched. The dependence of damage mechanism on laser wavelength and pulse width is discussed. It is found that from 1064 nm to 532 nm, LIDT is mainly absorption related, which is determined by film's extinction coefficient and stoichiometric defects. The rapid decrease of LIDT at 800 nm is due to the pulse width factor. TiO2 coatings are mainly thermally by damaged at long pulse (tau >= 220 ps). The damage shows ablation feature at 50 fs. (C) 2007 Elsevier B.V. All rights reserved.

Avaliação por ressonância magnética funcional da necrose coagulativa por ablação de radiofrequência nas metástases hepáticas colorretais

A maioria dos pacientes que apresentam metástases hepáticas colorretais (MHCR) não são elegíveis para ressecção. Por isso, outras técnicas para se alcançar o controle locorregional da doença têm sido utilizadas. A Ablação por Radiofrequência (ARF) hepática tem sido empregada frequentemente para o tratamento desta condição devido às boas taxas de resposta, principalmente quando associada ao emprego de quimioterápicos modernos. Apesar da caracterização das MHCR no pré-operatório estar bem estabelecida, os parâmetros de ressonância magnética (RM) após ARF no período pós-cirúrgico requerem maior padronização objetiva. O coeficiente de difusão aparente de água (CDA) tem sido usado na RM como um parâmetro de isquemia e necrose. Entretanto, não está ainda bem definido seu papel e das imagens ponderadas de difusão (DWI) na avaliação da necrose coagulativa gerada pela ARF, especificamente em pacientes com MHCR. O objetivo deste estudo consiste em avaliar o espectro de mudança em RM funcional após a ARF de MHCR. Foi realizado estudo retrospectivo entre 2001 e 2006, avaliando 51 pacientes que foram submetidos à ARF por MHCR no Hospital Johns Hopkins (Baltimore, EUA) dos quais 16 preencheram os critérios de inclusão. Os critérios de inclusão foram: (1) apresentar MHCR tratada cirurgicamente com intenção curativa por ARF guiados por ultrassom per-operatório, e (2) ter uma RM anterior e imediatamente após a cirurgia (até 10 dias). As imagens de RMs antes e após a ablação hepática para MCHR foram identificadas e revistas. As imagens de RM de difusão e captação de contraste foram feitas numa unidade de 1.5 T. Imagens em T2 e T1 foram realizadas na presença e ausência de contraste venoso. Todos os exames tiveram a espessura de 4 a 6 mm e um intervalo de 2 mm, apresentando um angulo de rotação de 150. O índice de difusão foi determinado com um b-valor (intensidade do gradiente de difusão) de 500 seg/mm2. As análises de parâmetros para avaliar e comparar o pré e pós ARF através da RM funcional incluiram: (1) valores do mapa de CDA, (2) captação de contraste, (3) difusão e (4) mudança no tamanho da lesão. Em adição, a sobrevida mediana global e tempo para recorrência local foram calculados. As imagens foram avaliadas por um consenso de dois radiologistas/cirurgiões. Foram avaliados no total 65 lesões, com tamanho médio pré-ablação de 1,7 cm. Após ablação o tamanho médio da lesão aumentou para 3,5 cm (p<0,001). A captação de contraste nas fases arterial e venosa diminuíram significativamente após ARF (diminuição média 10% e 17,5%, respectivamente, p = 0,002 e <0,001). O valor médio do mapa de CDA da lesão foi de 2.79 x 10-3 mm2/seg pré-ARF, e após ARF diminui em média para 1.75 x 10-3 mm2/seg (p<0.001). A sobrevida mediana global foi de 34,7 meses. A ressonância magnética funcional através da captação de contraste e difusão pode prover uma estimativa subjetiva e objetiva da necrose coagulativa tissular e da desidratação celular na área ablada por radiofrequência. Quando combinada ao aumento no tamanho do tumor, podem atuar como um marcador adicional de resposta tumoral.

Elemental signatures in otoliths of larval walleye pollock (Theragra chalcogramma) from the northeast Pacific Ocean

The population structure of walleye pollock (Theragra chalcogramma) in the northeastern Pacific Ocean remains unknown. We examined elemental signatures in the otoliths of larval and juvenile pollock from locations in the Bering Sea and Gulf of Alaska to determine if there were significant geographic variations in otolith composition that may be used as natural tags of population affinities. Otoliths were assayed by using both electron probe microanalysis (EPMA) and laser ablation inductively coupled plasma mass spectrometry (ICP-MS). Elements measured at the nucleus of otoliths by EPMA and laser ablation ICP-MS differed significantly among locations. However, geographic groupings identified by a multivariate statistical approach from EPMA and ICP-MS were dissimilar, indicating that the elements assayed by each technique were controlled by separate depositional processes within the endolymph. Elemental profiles across the pollock otoliths were generally consistent at distances up to 100 μm from the nucleus. At distances beyond 100 μm, profiles varied significantly but were remarkably consistent among individuals collected at each location. These data may indicate that larvae from various spawning locations are encountering water masses with differing physicochemical properties through their larval lives, and at approximately the same time. Although our results are promising, we require a better understanding of the mechanisms controlling otolith chemistry before it will be possible to reconstruct dispersal pathways of larval pollock based on probe-based analyses of otolith geochemistry. Elemental signatures in otoliths of pollock may allow for the delineation of fine-scale population structure in pollock that has yet to be consistently revealed by using population genetic approaches.

Changes in mass balance of South Cascade Glacier, North Cascades, 1959 to 1994

EXTRACT (SEE PDF FOR FULL ABSTRACT): Annual, winter, and summer mass balance measurements at South Cascade Glacier in the North Cascade Mountains of Washington State constitute a continuous time series 36 years long, from 1959 to 1994. ... The long-term trends at South Cascade Glacier are decreased winter accumulation and increased summer ablation, neither of which is conducive to glacier growth, so the trend in the Pacific Northwest is clearly away from an ice-age type of climate at the current time. The data also demonstrate that a glaciologically significant long-term change in snow precipitation can occur rapidly, in as short an interval as 1 year, much more rapidly than changes in temperature.

Artificial insemination in penaeid shrimps

Artificial Insemination (AI) is a tool for genetic manipulation in the shrimp stocks. It is seen as one of the means for propagating shrimp culture to new areas by controlled reproduction. Attempts at artificial insemination in the dominant closed-thelycum penaeid shrimps species of the area viz. Metapenaeus affinis and Metapenaeus brevicornis were induced in wild adult stocks collected off Mumbai coast. Female specimens were subjected to unilateral eyestalk ablation by pinching so as to induce moulting and maturation. AI was performed two days after moulting on these females when the cuticle was still soft and flexible. Moulting also ensured rejection of initial spermatophores, if present. Response of males to electrical stimulation for spermatophore expulsion was spontaneous. Use of tissue glue for spermatophore retention was found to be unnecessary. Latency period ranged between10-16 days, while spawning occurred within 10-12 days of spermatophore transfer. Three partial spawning were recorded viz., two in Metapenaeus affinis and one in Metapenaeus brevicornis with an average spawning and hatching rates of 30% and 72.3% respectively. Average survival from first nauplius (N1) to one-day old post-larva (PLI) was a meager 3.43%. Use of AI in genetic manipulation of shrimp stocks for aquacultural purposes is indicated.

Suggestive role of eye-stalk of Macrobrachium gangeticum Bate, 1868 in regulation of its reproductive behaviour

Role of eye-stalk of Macrobrachium gangeticum Bate, 1868 in its reproductive behaviour has been examined by conducting deletion and addition experiments. Eye-stalk ablation induced gonadal maturity in both sexes, leading to change in colour and size of ovaries and increase in GSI and oocyte diameter in females and increased length of testes and diameters of seminiferous tubules in males. Injection of eye-stalk extracts tended to at least partly restrict the effects in both sexes. The experiments thus suggested that the eye-stalk of M. gangeticum released some gonad inhibiting factors.

A simple method of tagging prawns

The recognition of individual animals is crucial to many aspects of research. Prawns (Penaeus monodon) present unique difficulties in this respect since they molt regularly. Thus, almost all tagging and marking methods developed for prawns so far have proven inadequate. Some tags or marks are lost during molting; others cause injury to the prawns. A new and efficient method has been developed at the Igang Seafarming Station of the Aquaculture Department. Rectangular brass tags measuring 5 mm by 20 mm and numbered consecutively are used. The prawn is held gently but firmly at the base of the carapace with the left hand while the right hand slips the brass tag around the stalk of the unablated eye and presses the tag gently. All tagging must be made under water to avoid stress. From May 29 to September 7 1977 to a total of 348 unilaterally-ablated adult female prawns were tagged on the unablated eyestalk in 5 batches to enable individual observations on gonadal maturation, molting, and growth. Periodic examinations were made four times a month to coincide with the different phases of the lunar cycle. On each examination, survival and recovery rates were recorded. The data included death due to immediate mortality during ablation and loss to cannibalism for the duration of the experiments. In all five tagging experiments, most of the prawns recovered had their tags intact. These included even dead and molting animals. The eyestalk tagging method is suitable for prawns because the tags can be attached without causing injury and has no effect on the rate of growth, maturity, molting and behavior of the animal. The tags are identifiable and permanent; they remain attached to the animal even after death.

The propagation of the mud crab Scylla serrata (F.) de Haan

The mud crab Scylla serrata is an important commercial species found in many brackish areas in the Philippines. During spawning and hatching, the berried females migrate to the sea. Seeds for pond stocking are obtained from the wild. Because of the unpredictability of seed supply, there is a need to propagate the species artificially. Thus, spawning, larval rearing, maturation, and rematuration of the species are being studied. The first attempts at hatching S. serrata were successful with rates varying between 75% and 90%. Two out of three trials on larval rearing yielded a few megalops. The first zoeal stages were fed diatoms, rotifers, Artemia salina, and bread yeast. Overfeeding programs were implemented during the critical premolting periods to prevent weakening of the larvae and lessen cannibalism. Larval weakening during the premolt makes them susceptible to attacks by fungi like Lagenidium and ciliates like Vorticella. S. serrata larvae survived salinity levels as low as 15 ppt until the 14th day of rearing. Other larvae were able to survive in salinities of 30-32 ppt for 8 to 13 days. Zoeal molting was hastened by lowering the salinity to 25-27 ppt. Artificial broodstocking of juveniles and adult crabs has been made possible using a simple refuge system made of three-compartmented hollow blocks. This system has been helpful in minimizing fighting among crabs. Remarkable growth rates have been observed with feeds like mussel meat and trash fish. Average growth increments of 11 mm carapace length and 20 . 35 g body weight have been observed every fortnight. A newly spent spawner could gain additional weight of 22 . 5 g in only 6 days. Feeding rates of juveniles and adult crabs have been established based on the average body weight from an experiment using mussel meat. Crabs feed more at night. In another experiment, eyestalk ablation was found to be effective in inducing growth and mating. Aside from hastening the molting process, copulation is induced even among the small crabs (average carapace length = 55 mm). Natural mating lasts about 26 hr. A copulation which lasted for seven days with a break in between was observed.

Land-based mass production of prawn (Penaeus monodon Fabricius) spawners

The first spawnings were obtained 12 days after ablation with 4 spawners yielding 784,000 eggs and a harvest of 250,000 P SUB-10 fry. Survival of females after 1 month was approximately 30%. Mortalities were mostly due to handling stress during the regular ovarian samplings as well as disease frm the accumulated excess feeds on the bottom of the tank. Male survival could not be recorded because of transfers to other tanks and addition of new stocks. Development seemed to peak 3 weeks after ablation. The average number of eggs per ablated spawner was 120,000. However, many of the partially spawned females were removed from the spawning tanks the following day so that remaining eggs released in the next 2 to 3 days could not be recorded. Estimate of the average number of eggs per ablated spawner is 120,000-150,000 in contrast to 500,000 per wild spawner. However, the low production cost more than compensates for the difference. Fry reared in the Wet Laboratory were used for experiments, mostly on feeding. Therefore, survival at harvest is not to be taken as a reflection of stock quality. Although fewer in number, larvae from ablated prawns are as healthy in terms of vigor in swimming and feeding as those from wild females. Most mortalities are due to inability to molt caused by lower water temperatures and inadequate feeding.

Notes on ovarian rematuration of ablated sugpo (prawn) Penaeus monodon Fabricius

To what extent spent P. monodon females can remature and spawn successive broods is an important question in terms of recycling spawners in a commercially viable operation. Corollary to this is the quantity and quality of fry from rematured females in comparison to those from first spawning. Of 347 experimental females, only 10.1% had a second spawning, and 1.4% a third spawning. To a large degree the low rate of rematuration is due to high spawner mortality - average survival period after spawning was only 6 days in a sample of 176 spawners. It took an average of 23 days after ablation for a prawn with undeveloped ovaries to mature and spawn. An ablated female may have another spawning in as little as 5 days after the previous one. Average fecundity was 180,000 eggs per second spawning, and 140,000 eggs per third spawning. The average number of eggs from first spawning ablated females was 110-120,000. Hatching rate was lower for rematuration: 44% for second spawnings, and 35% for third spawnings, as compared to 64% for first maturation.

Investigation of low nanosecond light-matter interaction mechanisms

Laser ablation of solid Silicon targets using pulsed Yb fiber lasers of pulse duration 1.5-400 ns Yb fiber lasers is studied in this work. Material responses of a range of pulse envelopes are examined including front peak (FP) and double peak (DP) pulses. Theoretical models for the interactions are examined and qualitative explanations of material response experiments are presented.

Micromachining of glassy carbon toolsets for micro embossing applications

Laser micro machining is fast gaining popularity as a method of fabricating micro scale structures. Lasers have been utilised for micro structuring of metals, ceramics and glass composites and with advances in material science, new materials are being developed for micro/nano products used in medical, optical, and chemical industries. Due to its favourable strength to weight ratio and extreme resistance to chemical attack, glassy carbon is a new material that offers many unique properties for micro devices. The laser machining of SIGRADUR® G grade glassy carbon was characterised using a 1065 nm wavelength Ytterbium doped pulsed fiber laser. The laser system has a selection of 25 preset waveforms with optimised peak powers for different pulsing frequencies. The optics provide spot diameter of 40 μm at the focus. The effect of fluence, transverse overlap and pulsing frequency (as waveform) on glassy carbon was investigated. Depth of removal and surface roughness were measured as machining quality indicators. The damage threshold fluence was determined to be 0.29 J/cm2 using a pulsing frequency of 250 kHz and a pulse width of 18 ns (waveform 3). Ablation rates of 17 < V < 300 μm3/pulse were observed within a fluence range of 0.98 < F < 2.98 J/cm2. For the same fluence variation, 0.6 μm to 6.8 μm deep trenches were machined. Trench widths varied from 29 μm at lower fluence to 47 μm at the higher fluence. Square pockets, 1 mm wide, were machined to understand the surface machining or milling. The depth of removal using both waveform 3 and 5 showed positive correlation with fluence, with waveform 5 causing more removal than waveform 3 for the same fluence. Machined depths varied from less than 1 μm to nearly 40 μm. For transverse overlap variation using waveform 3, the best surface finish with Rz = 1.1 μm was obtained for fluence 0.792 J/cm2 for transverse overlap of 1 μm, 6 μm, and 9 μm at machined depths of 22.9 μm, 6.6 μm, and 4.6 μm respectively. For fluence of 1.426 J/cm2, the best surface finish with Rz = 1.2 μm was obtained for transverse overlap of 6 μm, and 9 μm at machined depths of 12.46 μm, and 8.6 μm respectively. The experimental data was compiled as machining charts and utilised for fabricating a micro-embossing glassy carbon master toolsets as a capability demonstration.