Hydrogen purification for fuel cell using CuO/CeO(2)-Al(2)O(3) catalyst

CuO/CeO(2), CuO/Al(2)O(3) and CuO/CeO(2)-Al(2)O(3) catalysts, with CuO loading varying from 1 to 5 wt.%, were prepared by the citrate method and applied to the preferential oxidation of carbon monoxide in a reaction medium containing large amounts of hydrogen (PROX-CO). The compounds were characterized ex situ by X-ray diffraction, specific surface area measurements, temperature-programmed reduction and temperature-programmed reduction of oxidized surfaces; XANES-PROX in situ experiments were also carried out to study the copper oxidation state under PROX-CO conditions. These analyses showed that in the reaction medium the Cu(0) is present as dispersed particles. On the ceria, these metallic particles are smaller and more finely dispersed, resulting in a stronger metal-support interaction than in CuO/Al(2)O(3) or CuO/CeO(2)-Al(2)O(3) catalysts, providing higher PROX-CO activity and better selectivity in the conversion of CO to CO(2) despite the greater BET area presented by samples supported on alumina. It is also shown that the lower CuO content, the higher metal dispersion and consequently the catalytic activity. The redox properties of the ceria support also contributed to catalytic performance. (C) 2010 Elsevier B.V. All rights reserved.

A comparative study on preparation of TiO2 pellets as photocatalysts based on different precursors

The porous Ti0₂ pellets were prepared based on pigment grade titaina, P25 titania powder and titaniurn(lV) butoxide. The characterization was done with X-Ray diffraction, scanning electron microscopy and BET measurements. The result shows that Ti0₂ pellets by using titaniurn(IV) butoxide with some addictive have the best surface porosity, with specific surface area of 196.9m²/g. For pigment grade titania and P25 titania powder, it is still effective to enhance the surface area after reassembling. The surface area increased from 11.6 to 29.2 m²/g for pigment grade titania and from 50 to 84.4 m²/g for P25 titania powder. Furthermore, it has been investigated on how to optimize and get the highest surface area by controlling the sintering temperature, reaction temperature, pH of solution, and the amount of alcohol and addictive of surfactant during preparation. The experimental photocatalytic degradation of acetone and toluene was performed using titania pellets made from P25 titania powder.

Removal of VOCs by photocatalysis process using adsorption enhanced TiO2–SiO2 catalyst

Volatile organic compounds (VOCs) exist widely in both the indoor and outdoor environment. The main contributing sources of VOCs are motor vehicle exhaust and solvent utilization. Some VOCs are toxic and carcinogenic to human health, such as benzene. In this study, TiO₂–SiO₂ based photocatalysts were synthesized using the sol–gel method, with high surface areas of 274.1–421.1 m²/g obtained. Two types of pellets were used as catalysts in a fixed-bed reactor installed with a UV black light lamp. Experiments were conducted to compare their efficiencies in degrading the VOCs. Toluene was used as the VOC indicator. When the toluene laden gas stream passed through the photocatalytic reactor, the removal efficiencies were determined using a FTIR multi-gas analyser, which was connected to the outlet of the reactor to analyse the toluene concentrations. As the TiO₂–SiO₂ pellets used have a high adsorption capacity, they had dual functions as a photocatalyst and adsorbent in the hybrid photocatalysis and adsorption system. The experiments demonstrated that the porous photocatalyst with very high adsorptive capacity enhanced the subsequent photocatalysis reactions and lead to a positive synergistic effect. The catalyst can be self-regenerated by photocatalytic oxidation of the adsorbed VOCs. When the UV irradiation and feeding gas is continuous, a destruction efficiency of about 25% was achieved over a period of 20 h. Once the system was designed and operated into adsorption/regeneration mode, a higher removal efficiency of about 55% was maintained. It was found that the catalyst pellets with a higher surface area (421 m²/g) achieved higher conversion efficiency (100%) for a longer period than those with a lower surface area. A full spectrum scan was carried out using a Bio-rad Infrared spectrometer, finding that the main components of the treated gas stream leaving the reactor, along with untreated toluene, were CO₂ and water. The suspected intermediates of aliphatic hydrocarbons and CO were found in minimal amounts or were non detectable. The kinetic rate constants were calculated from the experimental results, it appeared that the stronger adsorption capacity, i.e. larger specific surface area, the higher conversion efficiency would be achieved.

Application of SWAT to model the water balance of the Woady Yaloak River catchment, Australia

The widespread land use changes that are expected to occur across the Corangamite region in southwest Victoria, Australia, have the potential to significantly alter the water balance of catchments. Adoption of the Soil and Water Assessment Tool (SWAT), which is a long-term water balance model, as a tool for predicting land use change impacts on catchment water balance for the Corangamite region is currently being considered. This paper describes the initial application of SWAT to the Woady Yaloak River catchment, located within the Corangamite region, to carry out an evaluation of its abilities for simulating the long-term water balance dynamics of the catchment. The performance of the model for predicting runoff at annual and monthly time scales was found to be very good. The excessive recharge of the shallow aquifer that occurred during winter, despite the subsoil being relatively impermeable, ultimately contributed to overestimation of baseflow and underestimation of interflow. The actual evapotranspiration from hydrologic response units (HRU s) containing eucalyptus trees was significantly less than that from HRUs containing pasture, a problem attributed to the incorrect simulation of Leaf Area Index (LAI) and biomass by the model for mature stands of eucalyptus trees and also to assigning inadequate values for two parameters that directly influence evapotranspiration. SWAT has very good potential for being used as tool to study land use change impacts across the Corangamite region provided that several modifications are made to the model to overcome some of the shortcomings and deficiencies that were identified in this initial application.

Integration of 3-PG into SWAT to simulate the growth of evergreen forests

SWAT cannot accurately simulate the seasonal fluctuations or the long-term trend of the Leaf Area Index (LAI) of evergreen forests. This deficiency has detrimental impacts for the prediction of interception and transpiration, two processes that have a significant influence on catchment water yield. This paper details the integration of the forest growth model 3-PG with SWAT to improve the simulation of LAI for evergreen forests. The integrated model, called SWAT/3-PG, was applied to the Woady Yaloak River Catchment in southern Australia where eucalyptus forests and pine plantations account for 30% of the total land use. SWAT/3-PG simulated the LAI of eucalypts and pines more accurately and realistically than the original version of SWAT. Forest LAI simulated by SWAT/3-PG agreed reasonably well with estimates of forest LAI derived independently from a Landsat satellite image. SWAT/3- PG has considerable value as a tool that managers can utilise to predict the impacts of land use change in catchments where evergreen forests are prevalent.

Effect of particle size on the photocatalytic activity of nanoparticulate zinc oxide

In this study, a three-stage process consisting of mechanical milling, heat treatment, and washing has been used to manufacture nanoparticulate ZnO powders with a controlled particle size and minimal agglomeration. By varying the temperature of the post-milling heat treatment, it was possible to control the average particle size over the range of 28–57 nm. The photocatalytic activity of these powders was characterized by measuring the hydroxyl radical concentration as a function of irradiation time using the spin-trapping technique with electron paramagnetic resonance spectroscopy. It was found that there exists an optimum particle size of approximately 33 nm for which the photocatalytic activity is maximized. The existence of this optimal particle size is attributable to an increase in the charge carrier recombination rate, which counteracts the increased activity arising from the higher specific surface area for a sufficiently small particle size.

Mechanochemical synthesis of nanocrystalline SnO2-ZnO photocatalysts

Mechanochemical processing of anhydrous chloride precursors with Na₂CO₃ has been investigated as a means of manufacturing nanocrystalline SnO₂ doped ZnO photocatalysts. High-energy milling and heat-treatment of a 0.1SnCl₂+0.9ZnCl₂+Na₂CO₃+4NaCl reactant mixture was found to result in the formation of a composite powder consisting of oxide grains embedded within a matrix of NaCl. Subsequent washing with deionized water resulted in removal of the NaCl matrix phase and partial hydration of the oxide reaction product with the consequent formation of ZnSn(OH)₆. The extent of this hydration reaction was found to decrease in a linear fashion with the temperature of the post-milling heat-treatment over the range of 400–700 °C. For a heat-treatment temperature of 700 °C, the SnO₂ doped ZnO powder was found to exhibit significantly higher photocatalytic activity than either single-phase SnO₂ or ZnO powders that were synthesized using similar processing conditions. The heightened photocatalytic activity of the SnO₂ doped ZnO was attributed to its higher specific surface area and the enhanced charge separation arising from the coupling of ZnO with SnO₂.

Recent developments in carbon nanotube membranes for water purification and gas separation

Carbon nanotubes (CNTs) are nanoscale cylinders of graphene with exceptional properties such as high mechanical strength, high aspect ratio and large specific surface area. To exploit these properties for membranes, macroscopic structures need to be designed with controlled porosity and pore size. This manuscript reviews recent progress on two such structures: (i) CNT Bucky-papers, a non-woven, paper like structure of randomly entangled CNTs, and (ii) isoporous CNT membranes, where the hollow CNT interior acts as a membrane pore. The construction of these two types of membranes will be discussed, characterization and permeance results compared, and some promising applications presented.

Special libraries

In Australia and New Zealand, the term 'special library' refers to libraries that provide resources and services to employees of an organization or industry.  The majority have collections and/or services supporting a specific subject area.  These include, but are not limited to, libraries in government department, law firms, private companies, banking and finance institutions, research organizations, religious groups and professional associations.

Functional applications of electrospun nanofibers

With the rapid development of nanoscience and nanotechnology over the last two decades, great progress has been made not only in preparation and characterization of nanomaterials, but also in their functional applications. As an important one-dimensional nanomaterial, nanofibers have extremely high specific surface area because of their small diameters, and nanofiber membranes are highly porous with excellent pore interconnectivity. These unique characteristics plus the functionalities from the polymers themselves impart nanofibers with many desirable properties for advanced applications.

Nanofibers - production, properties and functional applications

With the rapid development of nanoscience and nanotechnology over the last decades, great progress has been made not only in the preparation and characterization of nanomaterials, but also in their functional applications. As an important one-dimensional nanomaterial, nanofibers have extremely high specific surface area because of their small diameters, and nanofiber membranes are highly porous with excellent pore interconnectivity. These unique characteristics plus the functionalities from the materials themselves impart nanofibers with a number of novel properties for applications in areas as various as biomedical engineering, wound healing, drug delivery and release control, catalyst and enzyme carriers, filtration, environment protection, composite reinforcement, sensors, optics, energy harvest and storage , and many others. More and more emphasis has recently been placed on large-scale nanofiber production, the key technology to the wide usages of nanofibers in practice. Tremendous efforts have been made on producing nanofibers from special materials. Concerns have been raised to the safety issue of nanofibrous materials. This book is a compilation of contributions made by experts who specialize in their chosen field. It is grouped into three sections composed of twenty-one chapters, providing an up-to-date coverage of nanofiber preparation, properties and functional applications. I am deeply appreciative of all the authors and have no doubt that their contribution will be a useful resource of anyone associated with the discipline of nanofibers.

Superhydrophobic nanofibre membranes : effects of particulate coating on hydrophobicity and surface properties

Superhydrophobic electrospun polyacrylonitrile nanofibre membranes have been prepared by surface coating of silica nanoparticles and fluorinated alkyl silane. The coated membranes were characterised by scanning electron microscopy, water contact angle, thermogravimetry analysis, Brunauer–Emmett–Teller, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy and atomic force microscopy. It was shown that the loading of nanoparticle on the nanofibre membrane was controlled by the particle concentration in the coating solution, which played a critical role in the formation of superhydrophobic surface. Increased particle loading led to higher surface roughness and WCA. The nanoparticle coating had little influence on the porosity of the nanofibre membranes. However, overloading of the particles would affect the specific surface area of the nanofibre membrane.

Controlled synthesis of TiO2 hierarchical nanofibre structures via electrospinning and solvothermal processes : photocatalytic activity for degradation of methylene blue

The present article describes a new titanium oxide‐based (TiO2) photocatalyst that shows promise for acceleration of dye degradation. A hierarchical TiO2 nanostructure comprising nanorods on‐nanofibres has been prepared using a sol–gel route and electrospinning. Calcination of electrospun nanobre mats was performed in air at 500 °C. The TiO2 nanofibre surface was then exploited as a ‘seeding ground’ to grow TiO2 nanorods by a solvothermal process in NaOH. The nanofibres had a diameter of approximately 100 nm while the nanorods were evenly distributed on the nanofibre surface with a mean diameter of around 50–80 nm. The hierarchical nanostructure showed enhanced photocatalytic activity when compared to pure TiO2 nanofibres. This improved efficiency in degrading methylene blue through the photocatalytic process was attributed to the larger specific surface area of the TiO2 nanostructures, as well as high surface‐to‐volume ratio and higher reactive surface resulting in enhanced surface adsorption and interfacial redox reaction.

A preliminary study on the effect of macro cavities formation on properties of carbon nanotube bucky-paper composites

In this study, we focus on processing and characterizing composite material structures made of carbon nanotubes (CNTs) and reproducibly engineering macro-pores inside their structure. Highly porous bucky-papers were fabricated from pure carbon nanotubes by dispersing and stabilizing large 1 μm polystyrene beads within a carbon nanotube suspension. The polystyrene beads, homogeneously dispersed across the thickness of the bucky-papers, were then either dissolved or carbonized to generate macro cavities of different shape and properties. The impact of adding these macro cavities on the porosity, specific surface area and Young’s modulus was investigated and some benefits of the macro cavities will be demonstrated.

Control of porosity and pore size of metal reinforced carbon nanotube membranes

Membranes are crucial in modern industry and both new technologies and materials need to be designed to achieve higher selectivity and performance. Exotic materials such as nanoparticles offer promising perspectives, and combining both their very high specific surface area and the possibility to incorporate them into macrostructures have already shown to substantially increase the membrane performance. In this paper we report on the fabrication and engineering of metal-reinforced carbon nanotube (CNT) Bucky-Paper (BP) composites with tuneable porosity and surface pore size. A BP is an entangled mesh non-woven like structure of nanotubes. Pure CNT BPs present both very high porosity (>90%) and specific surface area (>400 m2/g). Furthermore, their pore size is generally between 20–50 nm making them promising candidates for various membrane and separation applications. Both electro-plating and electroless plating techniques were used to plate different series of BPs and offered various degrees of success. Here we will report mainly on electroless plated gold/CNT composites. The benefit of this method resides in the versatility of the plating and the opportunity to tune both average pore size and porosity of the structure with a high degree of reproducibility. The CNT BPs were first oxidized by short UV/O3 treatment, followed by successive immersion in different plating solutions. The morphology and properties of these samples has been investigated and their performance in air permeation and gas adsorption will be reported.