Análise do desempenho térmico de um sistema de aquecimento solar utilizando coletor com superfície absorvedora em chapas de PVC

It s presented a solar collector to be used in a system for heating bath water, whose main characteristic is its low cost. The collector consists of five plates of PVC with 10 mm thick, 200 mm in width and 1400mm in length, with an area equal to 1.4 square meters. The plates were connected in parallel to the ends of PVC tubes of  40 mm and 32 mm. The plates were coated on one side with aluminum sheets of soft drinks and beers cans open. The system worked on a thermosiphon and was tested in two configurations: the plates uncoated and coated with aluminum material, to determine the influence of material on the efficiency of the collector. For both configurations was used EPS plates below the surface to minimize heat losses from the botton. The thermal reservoir of the heating system is, also, alternative and low cost, since it was constructed from a polyethylene tank for storing water, with volume of 150 end 200 liters. It will be presented the thermal efficiency, heat loss, water temperature of the thermal reservoir at the end of the process and simulation of baths for a house with four residents. The will be demonstrated thermal, economic and material viability of the proposed collector, whose main innovation is the use of recyclables materials, cans of beer and soft drinks, to increase the temperature of the absorber plate.

Análise do desempenho térmico de um sistema de aquecimento solar de baixo custo

It presents a solar collector to be used in a system for heating water for bathing, whose main characteristics are low cost and easy manufacturing and assembly. The system operates under natural convection or thermosiphon. The absorbing surface of the collector is formed by twelve PVC pipes of 25 mm outside diameter connected in parallel via connections in T of the same material. The tubes were covered with absorbing fins made with recycled aluminum cans. We studied eight settings between absorber plate, thermal insulating EPS boards and thermal reservoirs 150 and 200 liters. It was determined the most efficient configuration for the correct purpose. We evaluated thermal parameters that proved the viability of the heating system studied

Projeto, construção e análise de eficiência térmica de um sistema de aquecimento solar de água de baixo custo

We studied the feasibility of using a system of Solar Water Heating (SAS) with low cost, for three configurations. In configurations I and II have the collector grid absorber composed of six PVC tubes placed in parallel on the tile cement. In configuration II, the PVC tubes were transparent cover made of plastic bottles. Configuration III uses a collector composed of 12 black HDPE pipes, supported on four cement tiles 2.44 m x 0.50 m, two by two overlapping and interspersed with a filling of glass wool, comprising an area exposed to the global radiation incident of 2.44 m2, with the top two tiles painted matte black. In this configuration, the HDPE pipes replace conventional PVC pipes painted black. The total cost of SAS for configuration III, the most economical, was around $ 150.00. For the configurations tested the system of operation was thermosyphon collector. The study showed that the proposed systems have good thermal efficiency, are easy to install and handle and have low cost compared to conventional.

Análise tribológica de um sistema de acionamento alternativo de pigs para a indústria do petróleo

It is analyzed through the concepts of tribology and mechanical contact and damage the suggestion of implementing a backup system for traction and passage of Pipeline Inspection Gauge (Pig) from the inside of pipelines. In order to verify the integrity of the pipelines, it is suggested the possibility of displacement of such equipment by pulling wires with steel wires. The physical and mechanical characteristics of this method were verified by accelerated tests in the laboratory in a tribological pair, wire versus a curve 90. It also considered the main mechanisms of wear of a sliding system with and without lubricant, in the absence and presence of contaminants. To try this, It was constructed a test bench able to reproduce a slip system, work on mode back-and-forth ("reciprocation"). It was used two kinds of wires, a galvanized steel and other stainless steel and the results achieved using the two kinds of steel cables were compared. For result comparative means, it was used steel cables with and without coating of Poly Vinyl Chloride (PVC). The wires and the curves of the products were characterized using metallographic analysis, microhardness Vickers tests, X-ray diffraction (XRD), X-Ray Refraction (XRF) and tensile tests. After the experiments were analyzed some parameters that have been measurable, it demonstrates to the impracticality of this proposed method, since the friction force and the concept of alternating request at the contact between the strands of wire and the inner curves that are part ducts caused severe wear. These types of wear are likely to cause possible failures in future products and cause fluid leaks

Análise teórico-experimental do coeficiente de perfomance (COP) de um sistema de refrigeração por jato-compressão

The use of waste heat of energy conversion equipment to produce a cooling effect, consists currently in a very interesting way of efficiency improvement of energy systems. The present research has as intention the theoretical and experimental study of a new intermittent refrigeration system ejector cycle characteristics, with use of waste heat. Initially, was doing a bibliographical survey about the vapor ejector refrigeration system technology. In the following stage was doing a simulation of the corresponding thermodynamic cycle, with preliminarily intention to evaluate the performance of the system for different refrigerants fluids. On the basis of the results of the simulation were selected the refrigerant fluid and developed an experimental group of benches of the refrigeration system considered, where pressure and temperature sensory had been inserted in strategical points of the refrigeration archetype and connected to a computerized data acquisition system for measure the refrigerant fluid properties in the thermodynamic cycle. The test results obtained show good agreement with the literature

Análise da influência de superfícies refletivas nas perdas de calor de sistema térmicos

The use of reflective surfaces functioning as thermal insulator has grown significantly over the years. Reflective thermal insulator are materials that have several characteristics such as low emissivity, low absorptivity and high reflectivity in the infrared spectrum. The use of these materials has grown a lot lately, since it contains several important radioactive properties that minimize the heat loss of thermal systems and cooling systems that are used to block the heat on the roof of buildings. A system made of three surfaces of 316 stainless steel mirror was built to analyze the influence of reflective surfaces as a way to reduce the heat loss and thereby conserve the energy of a thermal system. The system was analyzed both with and without the presence of vacuum, and then compared with a system that contained glass wool between the stainless steel mirror walls, since this isolator is considered resistive and also broadly used around the world in thermal systems. The reflectivity and emissivity of the surfaces used were also measured in this experiment. A type K thermocouple was fixed on the wall of the system to obtain the temperature of the stainless steel mirror surfaces and to analyze the thermal behavior of each configuration used. The results showed an efficiency of 13% when the reflective surfaces were used to minimize the heat loss of the thermal system. However, the system with vacuum had the best outcome, a 60% efficiency. Both of these were compared to the system made of glass wool as a thermal insulator

Análise da viabilidade econômica de um sistema de aquecimento solar de água para uma empresa do setor hoteleiro

This paper presents an analysis of technical and financial feasibility of the use of a solar system for water heating in a fictitious hotel located in the Northeast region. Thereunto it is used techniques of solar collectors´ sizing and methods of financial mathematics, such as Net Present Value (NPV), Internal Rate of Return (IRR) and Payback. It will also be presented a sensitivity analysis to verify which are the factors that impact the viability of the solar heating. Comparative analysis will be used concerning three cities of distinct regions of Brazil: Curitiba, Belém and João Pessoa. The viability of using a solar heating system will be demonstrated to the whole Brazil, especially to the northeast region as it is the most viable for such an application of solar power because of its high levels of solar radiation. Among the cities examined for a future installation of solar heating systems for water heating in the hotel chain, João Pessoa was the one that has proved more viable.

Comparação entre planejamento estatístico experimental e análise dimensional em operações de mistura e separação para sistema óleo-água

This work aims to determine a better methodology to help predicting some operational parameters to a new design of mixer-settler on treating wastewater produced by petroleum industry, called MDIF (Misturador-Decantador à Inversão de Fases/ Mixer-Settler based on Phase Inversion MSPI). The data from this research were obtained from the wastewater treatment unit, called MSPI-TU, installed on a wastewater treatment plant (WTP) of PETROBRAS/UO-RNCE. The importance in determining the better methodology to predict the results of separation and extraction efficiency of the equipment, contributes significantly to determine the optimum operating variables for the control of the unit. The study was based on a comparison among the experimental efficiency (E) obtained by operating MSPI-TU, the efficiency obtained by experimental design equation (Eplan) from the software Statistica Experimental Design® (version 7.0), and the other obtained from a modeling equation based on a dimensional analysis (Ecalc). The results shows that the experimental design equation gives a good prediction of the unit efficiencies with better data reliability, regarding to the condition before a run operation. The average deviation between the proposed by statistic planning model equation and experimental data was 0.13%. On the other hand, the efficiency calculated by the equation which represents the dimensional analysis, may result on important relative deviations (up 70%). Thus, the experimental design is confirmed as a reliable tool, with regard the experimental data processing of the MSPI-TU

Evolução da biodegradabilidade da matéria orgânica em um sistema de lagoas de estabilização

Waste stabilization ponds (WSP) have been widely used for sewage treatment in hot climate regions because they are economic and environmentally sustainable. In the present study a WSP complex comprising a primary facultative pond (PFP) followed by two maturation ponds (MP-1 and MP-2) was studied, in the city of Natal-RN. The main objective was to study the bio-degradability of organic matter through the determination of the kinetic constant k throughout the system. The work was carried out in two phases. In the first, the variability in BOD, COD and TOC concentrations and an analysis of the relations between these parameters, in the influent raw sewage, pond effluents and in specific areas inside the ponds was studied. In the second stage, the decay rate for organic matter (k) was determined throughout the system based on BOD tests on the influent sewage, pond effluents and water column samples taken from fixed locations within the ponds, using the mathematical methods of Least Squares and the Thomas equation. Subsequently k was estimated as a function of a hydrodynamic model determined from the dispersion number (d), using empirical methods and a Partial Hydrodynamic Evaluation (PHE), obtained from tracer studies in a section of the primary facultative pond corresponding to 10% of its total length. The concentrations of biodegradable organic matter, measured as BOD and COD, gradually reduced through the series of ponds, giving overall removal efficiencies of 71.95% for BOD and of 52.45% for COD. Determining the values for k, in the influent and effluent samples of the ponds using the mathematical method of Least Squares, gave the following values respectively: primary facultative pond (0,23 day-1 and 0,09 day-1), maturation 1 (0,04 day-1 and 0,03 day-1) and maturation 2 (0,03 day-1 and 0,08 day-1). When using the Thomas method, the values of k in the influents and effluents of the ponds were: primary facultative pond (0,17 day-1 and 0,07 day-1), maturation 1 (0,02 day-1 and 0,01 day-1) and maturation 2 (0,01 day-1 and 0,02 day-1). From the Partial Hydrodynamic Evaluation, in the first section of the facultative pond corresponding to 10% of its total length, it can be concluded from the dispersion number obtained of d = 0.04, that the hydraulic regime is one of dispersed flow with a kinetic constant value of 0.20 day-1

Otimização de um sistema de distribuição predial de água fria: estudo de caso

This dissertation presents a methodology to the optimization of a predial system of cold water distribution. It s about a study of a case applied to the Tropical Buzios Residential Condominium, located in the Búzio s Beach, Nísia Floresta city, the east coast of the Rio Grande do Norte state, twenty kilometers far from Natal. The design of cold water distribution networks according to Norm NBR 5626 of the ABNT - Brazilian Association of Techniques Norms, does not guarantee that the joined solution is the optimal solution of less cost. It s necessary the use of an optimization methodology, that supplies us, between all the possible solutions, the minimum cost solution. In the optimization process of the predial system of water distribution of the Tropical Búzios Condominium, is used Method Granados, that is an iterative algorithm of optimization, based on the Dynamic Programming, that supplies the minimum cost s network, in function of the piezometric quota of the reservoir. For the application of this Method in ramifies networks, is used a program of computer in C language. This process is divided in two stages: attainment of the previous solution and reduction of the piezometric quota of headboard. In the attainment of the previous solution, the minors possible diameters are used that guarantee the limit of maximum speed and the requirements of minimum pressures. The piezometric quota of headboard is raised to guarantee these requirements. In the second stage of the Granados Method, an iterative process is used and it objective is to reduce the quota of headboard gradually, considering the substitution of stretches of the network pipes for the subsequent diameters, considering a minimum addition of the network cost. The diameter change is made in the optimal stretch that presents the lesser Exchange Gradient. The process is locked up when the headboard quota of desired is reached. The optimized network s material costs are calculated, and is made the analysis of the same ones, through the comparison with the conventional network s costs

Análise tempo-intensidade dos estímulos doce e amargo de extrato de folhas de estévia [Stevia rebaudiana (Bert.) Bertoni] em doçura equivalente a sacarose

O extrato de folhas de estévia (Stevia rebaudiana Bertoni) é o único edulcorante utilizado na substituição da sacarose, que pode ser produzido totalmente no Brasil. O objetivo deste estudo foi determinar os comportamentos de características temporais dos estímulos doce e amargo da estevia em doçuras equivalentes a soluções de sacarose (DESS) a 3 e 10%. As curvas tempo-intensidade (T-I) para cada substância foram coletadas utilizando-se o programa Sistema de Coleta de Dados Tempo-Intensidade - SCDTI para Windows, onde os provadores registravam com auxílio do mouse a percepção de cada estímulo solicitado em função do tempo, para cada amostra. Os parâmetros das curvas T-I coletados foram: tempo de intensidade máxima (TImax), intensidade máxima (Imax), tempo onde a intensidade máxima começa a declinar (Td), tempo de platô (Platô), área sob a curva (Área) e tempo total de duração do estímulo (Ttot). Os parâmetros Td, Ttot, Área e Platô das curvas T-I para o estímulo doce nos dois níveis de doçura foram significativamente superiores para estévia, enquanto TImax e Imax foram significativamente menores (p£0,05), sendo que as diferenças entre os valores para as duas substâncias foram muito maiores a DESS a 10%. A sacarose não apresentou nenhum registro para o estímulo amargo tanto a 3 como a 10%, enquanto a estévia apresentou curvas T-I características, com intensidade e o tempo total de duração dependente da concentração.

Análise tempo-intensidade dos gostos doce e amargo de extrato de folhas de estévia (Stévia rebaudiana Bertoni) em doçura equivalente a sacarose

O extrato de folhas de estévia (Stévia rebaudiana Bertoni) é o único edulcorante utilizado na substituição da sacarose, que pode ser produzido totalmente no Brasil. Este trabalho objetivou determinar o comportamento de características temporais dos estímulos doce e amargo do extrato de estévia em doçuras equivalentes a soluções de sacarose (DESS) a 3 e 10%. As curvas tempo-intensidade (T-I) para cada substância foram coletadas utilizando-se o programa Sistema de Coleta de Dados Tempo-Intensidade - SCDTI para Windows, onde os provadores registravam com auxílio do mouse a percepção de cada estímulo solicitado em função do tempo, para cada amostra. Os parâmetros das curvas T-I determinados foram: tempo de intensidade máxima (TImax), intensidade máxima (Imax), tempo onde a intensidade máxima começa a declinar (Td), tempo de platô (Platô), área sob a curva (Área) e tempo total de duração do estímulo (Ttot). Os parâmetros Td, Ttot, Área e Platô das curvas T-I para o estímulo doce nos dois níveis de doçura significativamente foram superiores para o extrato de estévia, enquanto TImax e Imax foram significativamente menores (p£ 0,05). As diferenças entre os valores de sacarose e extrato de estévia foram muito maiores a DESS a 10%. A sacarose não apresentou nenhum registro para o estímulo amargo tanto a 3 como a 10%, enquanto a estévia apresentou curvas T-I características, com intensidade e o tempo total de duração dependente da concentração.

Análise citoarquitetônica dos componentes do sistema de temporização circadiana do sagui (Calithrix jacchus), comparada com a inervação das suas principais aferências

The suprachiasmatic nucleus (SCN) of the anterior hypothalamus, together with the intergeniculate leaflet (IGL) of the thalamus are considered the central components of the circadian timing system (CTS) of mammals. This system is responsible for the generation and regulation of circadian rhythms by establishing a temporal organization of physiological processes and behaviors. The neuronal specific nuclear protein (NeuN) has been widely used as a neuronal marker in several studies. Since glial fibrillary acidic protein (GFAP) is a component of intermediate filaments found in the cytoplasm of astrocytes and is commonly used as a specific marker for these cells. This study aims to identify, in the marmoset, the NeuN immunoreactive neurons and glial cells immunoreactive to GFAP, as well as map the major route of photic synchronization of the STC, retinohypothalamic tract (RHT), and identify the indirect pathway to the SCN and pregeniculate nucleus (PGN) - structure homologous to IGL rodents, using immunohistochemical and cytoarchitectonic techniques. Observed in SCN the presence of neurons immunoreactive to NeuN and terminals immunoreactive subunit b of cholera toxin (CTb), neuropeptide Y (NPY) and serotonin (5- HT). In the PGN noted the presence of the NeuN and NPY immunoreactive neurons and the immunoreactive terminals CTb and 5-HT. Astrocytes are present throughout the extent of the SCN and the PGN this New World primate

Análise crítica do processo de auditoria de sistema de gestão da qualidade no setor aeroespacial

A auditoria de sistema de gestão da qualidade é utilizada pelas organizações para melhorar o seu desempenho por meio de avaliações sistemáticas dos processos. Ao mesmo tempo, a atividade de auditoria vem sendo questionada quanto à sua capacidade de promover essa melhoria. Diante deste cenário, este artigo objetiva analisar fatores que afetam o processo de auditoria de certificação do sistema de gestão da qualidade, de modo a indicar oportunidades de melhoria das auditorias. A pesquisa é delimitada a auditorias no setor aeroespacial, que são orientadas pela NBR 15100. Foi realizada uma survey com auditores experientes nos anos de 2009 e 2010. São identificados fatores como comunicação, seleção da equipe, conhecimento do setor e os resultados mostram a existência de discrepâncias consideráveis entre o nível de importância e de aplicação desses fatores nas organizações auditadas.

O sistema de garantia dos direitos da criança e do adolescente: análise da trajetória e do processo de resolubilidade dos casos de violência doméstica sexual em Recife PE (2007-2011)

This work discourses about the child and adolescent s Guaranty System of Rights (GSR), on the intervention in cases of juvenile domestic sexual violence, in Recife. The course (trajectory) is analyzed, where circulate cases of sexual violence, until its resolution, in (GSR). Actually, the violence represents a serious problem of public health. Was thought about the difficulties and the limits that make GSR become a full field of contradictions and challenges for the effectiveness of the children and adolescents rights. Therefore, it was verified the treatments that are developed by GSR, how this system is structured and articulated and how occurs the resolution of the sexual violence cases against children and adolescents. Proceedings of the quantitative and qualitative research were used, was done observation, directed interview and analysis of documents. Thus, the field research was the visits in these institutions: Restauração Hospital, Police Management of the Child and Adolescent (PMCA) three Guardianship Councils, Dom Helder Camara Center of Studies and Social Action (CENDHEC) and the Tribunal of Childhood and Adolescence. The research subjects were seven professionals of GSR. The theoretical discussion is guided in reflections about the children and youth rights, in the violence theme and in the construction and institutionalization process of GSR. In this experiment, was noticed there are many difficulties for working together the GSR, because many obstacles are found when we call the responsible institutions, besides some violence cases happen again. This system is not totally institutionalized and articulated, faces structural problems, material, poorly qualified professionals, underinvestment, low transfer of public resources, among other difficulties, causing many losses in the implementation of public policies that enforce secured rights by legislation