Avaliação de concretos reforçados por confinamento com manta de fibra de vidro estrutural e pré-impreganada

Due to the occurrence of diseases in the use of structural reinforcements in composites, with presentation of concrete blanket detachment, has been identified the need to evaluate the performance of concrete reinforced with glass fiber. This study aims to evaluate these concretes by means of testing methodologies, using concrete with low resistance with structural reinforcement for confinement by preimpregnated glass fiber and traditional fiberglass blanket. The first stage of work was the development of methodologies for analysis, opting for four types, such as the acoustic survey, strength to compressive, the pull-off and ultrasound. Next, tests were carried out using the four selected methodologies in 30 of proof-of-specimens by 5x10 cm, 15 were reinforced with the traditional fiberglass blanket with 5specimens exposed to test a marine environment of marine coastline of Natal-RN and 15 were reinforced with a pre-impregnated glass fiber blanket, as well as 5specimens exposed to a test environment of the marine coastline of Natal-RN. After conducting the acoustic survey, it has been verified a lack of delaminating and air bubbles in the samples, confirming the absence of gross shortcomings in the implementation of the ribs both the traditional fiberglass blanket and in the preimpregnated fiber glass blanket. After carrying out methods of pull-off and compressive strengthening test it was observed that the reinforced proof-bodies with pre-impregnated glass blanket showed maximum stresses higher than the traditional fiberglass blanket; consequently a greater grip with the formation of a smaller area of . fracture, unlike traditional glass mat, which showed lower maximum stresses, with a greater area of fracture. It was also found that the traditional fiberglass blanket presented detachment of blanket-concrete interface, unlike the pre-impregnated fiberglass blanket, which showed a better grip on the blanket-concrete interface. In the trial of ultrasound there was no presence of cracks in the blanket-concrete interface, yielding to both blankets good compactness of the concrete. At the end of this work, they were developed and proposed two methods of testing for evaluation of reinforced concrete structures with composites, for standardization, the acoustic survey and pull-off

Comportamento magnético de compósitos de matriz polimérica com adição de ferritas

Polymer matrix composites offer advantages for many applications due their combination of properties, which includes low density, high specific strength and modulus of elasticity and corrosion resistance. However, the application of non-destructive techniques using magnetic sensors for the evaluation these materials is not possible since the materials are non-magnetizable. Ferrites are materials with excellent magnetic properties, chemical stability and corrosion resistance. Due to these properties, these materials are promising for the development of polymer composites with magnetic properties. In this work, glass fiber / epoxy circular plates were produced with 10 wt% of cobalt or barium ferrite particles. The cobalt ferrite was synthesized by the Pechini method. The commercial barium ferrite was subjected to a milling process to study the effect of particle size on the magnetic properties of the material. The characterization of the ferrites was carried out by x-ray diffraction (XRD), field emission gun scanning electron microscopy (FEG-SEM) and vibrating sample magnetometry (VSM). Circular notches of 1, 5 and 10 mm diameter were introduced in the composite plates using a drill bit for the non-destructive evaluation by the technique of magnetic flux leakage (MFL). The results indicated that the magnetic signals measured in plates with barium ferrite without milling and cobalt ferrite showed good correlation with the presence of notches. The milling process for 12 h and 20 h did not contribute to improve the identification of smaller size notches (1 mm). However, the smaller particle size produced smoother magnetic curves, with fewer discontinuities and improved signal-to-noise ratio. In summary, the results suggest that the proposed approach has great potential for the detection of damage in polymer composites structures

Estudo comparativo de pás para aerogeradores de grande porte fabricadas em materiais compósitos reforçadas com fibra de carbono ou fibra de vidro

The research and development of wind turbine blades are essential to keep pace with worldwide growth in the renewable energy sector. Although currently blades are typically produced using glass fiber reinforced composite materials, the tendency for larger size blades, particularly for offshore applications, has increased the interest on carbon fiber reinforced composites because of the potential for increased stiffness and weight reduction. In this study a model of blade designed for large generators (5 MW) was studied on a small scale. A numerical simulation was performed to determine the aerodynamic loading using a Computational Fluid Dynamics (CFD) software. Two blades were then designed and manufactured using epoxy matrix composites: one reinforced with glass fibers and the other with carbon fibers. For the structural calculations, maximum stress failure criterion was adopted. The blades were manufactured by Vacuum Assisted Resin Transfer Molding (VARTM), typical for this type of component. A weight comparison of the two blades was performed and the weight of the carbon fiber blade was approximately 45% of the weight of the fiberglass reinforced blade. Static bending tests were carried out on the blades for various percentages of the design load and deflections measurements were compared with the values obtained from finite element simulations. A good agreement was observed between the measured and calculated deflections. In summary, the results of this study confirm that the low density combined with high mechanical properties of carbon fibers are particularly attractive for the production of large size wind turbine blades

Efeito da adição do poli(etileno acrilato de metila) (ema) e da fibra de linter de algodão nas propriedades do poli(tereftalato de etileno) reciclado (petrec)

The development of new materials to fill the demand of technological advances is a challenge for many researchers around the world. Strategies such as making blends and composites are promising alternatives to produce materials with different properties from those found in conventional polymers. The objective of this study is to evaluate the effect of adding the copolymer poly(ethylene methyl acrylate) (EMA) and cotton linter fibers (LB) on the properties of recycled poly(ethylene terephthalate) (PETrec) by the development of PETrec/EMA blend and PETrec/EMA/LB blend composite. In order to improve the properties of these materials were added as compatibilizers: Ethylene - methyl acrylate - glycidyl methacrylate terpolymer (EMA-GMA) and maleic anhydride grafted polyethylene (PE-g-MA). The samples were produced using a single screw extruder and then injection molded. The obtained materials were characterized by thermogravimetry (TG), melt flow index (MFI) mensurements, torque rheometry, pycnometry to determinate the density, tensile testing and scanning electron microscopy (SEM). The rheological results showed that the addition of the EMA copolymer increased the viscosity of the blend and LB reduces the viscosity of the blend composite. SEM analysis of the binary blend showed poor interfacial adhesion between the PETrec matrix and the EMA dispersed phase, as well as the blend composite of PETrec/EMA/LB also observed low adhesion with the LB fiber. The tensile tests showed that the increase of EMA percentage decreased the tensile strength and the Young s modulus, also lower EMA percentage samples had increased the elongation at break. The blend composite showed an increase in the tensile strength and in the Young`s modulus, and a decrease in the elongation at break. The blend formulations with lower EMA percentages showed better mechanical properties that agree with the particle size analysis which showed that these formulations presented a smaller diameter of the dispersed phase. The blend composite mechanical tests showed that this material is stronger and stiffer than the blend PETrec/EMA, whose properties have been reduced due to the presence of EMA rubbery phase. The use of EMA-GMA was effective in reducing the particle size of the EMA dispersed phase in the PETrec/EMA blend and PE-g-MA showed evidences of reaction with LB and physical mixture with the EMA

Desenvolvimento de sistemas embarcados para redes de sensores e atuadores sem fio aplicadas em unidades de elevação de petróleo do tipo Plunger-Lift

The Wireless Sensor Networks (WSN) methods applied to the lifting of oil present as an area with growing demand technical and scientific in view of the optimizations that can be carried forward with existing processes. This dissertation has as main objective to present the development of embedded systems dedicated to a wireless sensor network based on IEEE 802.15.4, which applies the ZigBee protocol, between sensors, actuators and the PLC (Programmable Logic Controller), aiming to solve the present problems in the deployment and maintenance of the physical communication of current elevation oil units based on the method Plunger-Lift. Embedded systems developed for this application will be responsible for acquiring information from sensors and control actuators of the devices present at the well, and also, using the Modbus protocol to make this network becomes transparent to the PLC responsible for controlling the production and delivery information for supervisory SISAL

Pirólise termoquímica de pós da fibra de coco seco em um reator de cilindro rotativo para produção de bio-óleo

This master thesis aims at developing a new methodology for thermochemical degradation of dry coconut fiber (dp = 0.25mm) using laboratory rotating cylinder reactor with the goal of producing bio-oil. The biomass was characterized by infrared spectroscopy with Fourier transform FTIR, thermogravimetric analysis TG, with evaluation of activation energy the in non-isothermal regime with heating rates of 5 and 10 °C/min, differential themogravimetric analysis DTG, sweeping electron microscopy SEM, higher heating value - HHV, immediate analysis such as evaluated all the amounts of its main constituents, i.e., lignin, cellulose and hemicelluloses. In the process, it was evaluated: reaction temperature (450, 500 and 550oC), carrier gas flow rate (50 and 100 cm³/min) and spin speed (20 and 25 Hz) to condensate the bio-oil. The feed rate of biomass (540 g/h), the rotation of the rotating cylinder (33.7 rpm) and reaction time (30 33 min) were constant. The phases obtained from the process of pyrolysis of dry coconut fiber were bio-oil, char and the gas phase non-condensed. A macroscopic mass balance was applied based on the weight of each phase to evaluate their yield. The highest yield of 20% was obtained from the following conditions: temperature of 500oC, inert gas flow of 100 cm³/min and spin speed of 20 Hz. In that condition, the yield in char was 24.3%, non-condensable gas phase was 37.6% and losses of approximately 22.6%. The following physicochemical properties: density, viscosity, pH, higher heating value, char content, FTIR and CHN analysis were evaluated. The sample obtained in the best operational condition was subjected to a qualitative chromatographic analysis aiming to know the constituents of the produced bio-oil, which were: phenol followed by sirigol, acetovanilona and vinyl guaiacol. The solid phase (char) was characterized through an immediate analysis (evaluation of moisture, volatiles, ashes and fixed carbon), higher heating value and FTIR. The non-condensing gas phase presented as main constituents CO2, CO and H2. The results were compared to the ones mentioned by the literature.

Adsorção de cobre e cromo utilizando fibra de sisal visando o tratamento da água produzida pela indústria petrolífera

Currently, the oil industry is the biggest cause of environmental pollution. The objective was to reduce the concentration of copper and chromium in the water produced by the oil industry. It was used as adsorbent natural sisal fiber Agave sp treated with nitric acid and sodium hydroxide. All vegetable fibers have physical and morphological properties that enablies the adsorption of pollutants. The basic composition of sisal is cellulose, hemicellulose and lignin. The features are typically found in the characterization of vegetable fibers, except the surface area that was practically zero. In the first stage of adsorption, it was evaluated the effect of temperature and time skeeking to optimize the execution of the factorial design. The results showed that the most feasible fiber was the one treated with acid in five hours (30°C). The second phase was a factorial design, using acid and five hours, this time was it determined in the first phase. The tests were conducted following the experimental design and the results were analyzed by statistical methods in order to optimize the main parameters that influence the process: pH, concentration (mol / L) and fiber mass/ metal solution volume. The volume / mass ratio factor showed significant interference in the adsorption process of chromium and copper. The results obtained after optimization showed that the highest percentages of extraction (98%) were obtained on the following operating conditions: pH: 5-6, Concentration: 100 ppm and mass/ volume: 1 gram of fiber/50mL solution. The results showed that the adsorption process was efficient to remove chromium and copper using sisal fibers, however, requiring further studies to optimize the process.

Processamento Inteligente de Sinais de Pressão e Temperatura Adquiridos Através de Sensores Permanentes em Poços de Petróleo

Originally aimed at operational objectives, the continuous measurement of well bottomhole pressure and temperature, recorded by permanent downhole gauges (PDG), finds vast applicability in reservoir management. It contributes for the monitoring of well performance and makes it possible to estimate reservoir parameters on the long term. However, notwithstanding its unquestionable value, data from PDG is characterized by a large noise content. Moreover, the presence of outliers within valid signal measurements seems to be a major problem as well. In this work, the initial treatment of PDG signals is addressed, based on curve smoothing, self-organizing maps and the discrete wavelet transform. Additionally, a system based on the coupling of fuzzy clustering with feed-forward neural networks is proposed for transient detection. The obtained results were considered quite satisfactory for offshore wells and matched real requisites for utilization

Pré-concentração de cádmio com Saccharomyces cerevisiae e determinação em águas fluviais usando espectrometria de emissão óptica com plasma indutivamente acoplado

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Períodos de interferência das plantas daninhas em algodoeiro de fibra colorida ‘BRS Safira’

This study aimed to determine the late-season presence of weeds in reddish brown cotton (cultivar BRS Safira) and the critical times for removing weeds. The experiment was carried out in the area of Empresa Brasileira de Pesquisa Agropecuária (EMBRAPA) in Missao Velha-CE, Brazil, located at 7 degrees 42'07" S latitude and 39 degrees 24'18" WGr. longitude, during the 2007/2008 season. The treatments consisted of two control groups: weed-free crop during the initial period after crop emergency, and crop kept with weeds during initial period after plant emergency. Both consisted, 0; 20; 40; 60; 80 e 120 days after crop emergency (DAE), the weed community was evaluated by two phytosociological indices (relative dominance and relative importance). Regression analysis was performed as the model of sigmoidal Boltzman, using data from productivity separately within each type of competition, to identify the critical periods of competition, considering 2; 5 and 10% reduction in yield. The community of weeds was composed by 21 species, standing out among them: Richardia grandiflora, Amaranthus deflexus, Eleusine indica, Merremia aegyptia, Eragrotis pilosa, Cenchrus echinatus and Waltheria indica. Considering 2; 5 and 10% reduction in yield fiber as acceptable, the critical period before weed interference were, respectively, 8; 14 and 20 DAE. The critical period of weed interference, for those same levels of losses, were respectively, 100; 82 and 60 days.

Tributação, finanças públicas e política fiscal: uma análise sob a óptica do direito e economia

In the Brazilian legal scenario, the study of taxation has traditionally been restricted to positivist analysis, concerned with investigating the formal aspects of the tax legal rule. Despite its relevance to the formation of the national doctrine of tax, such formalist tradition limits the discipline, separating it from reality and the socioeconomic context in which the Tax Law is inserted. Thus, the proposal of the dissertation is to examine the fundamentals and nature of taxation and tax legal rules from the perspective of Law and Economics (Economic Analysis of Law). For this purpose, the work initially reconnects the Tax Law and Science of Finance (or Public Finance) and Fiscal Policy, undertaking not only a legal analysis, but also economic and financial analysis of the theme. The Economics of Public Sector (or Modern Public Finance) will contribute to the research through topics such as market failures and economic theory of taxation, which are essential to an economic approach to Tax Law. The core of the work lies in the application of Law and Economics instruments in the study of taxation, analyzing the effects of tax rules on the economic system. Accordingly, the dissertation examines the fundamental assumptions that make up the Economic Analysis of Law (as the concept of economic efficiency and its relation to equity), relating them to the tax phenomenon. Due to the nature of the Brazilian legal system, any worth investigation or approach, including Law and Economics, could not pass off the Constitution. Thus, the constitutional rules will serve as a limit and a prerequisite for the application of Law and Economics on taxation, particularly the rules related to property rights, freedom, equality and legal certainty. The relationship between taxation and market failures receives prominent role, particularly due to its importance to the Law and Economics, as well as to the role that taxation plays in the correction of these failures. In addition to performing a review of taxation under the approach of Economic Analysis of Law, the research also investigates the reality of Brazilian tax system, applying the concepts developed in relevant cases and issues to the national scene, such as the relationship between taxation and development, the compliance costs of taxation, the tax evasion and the tax enforcement procedure. Given the above, it is intended to lay the groundwork for a general theory of Economic Analysis of Tax Law, contextualizing it with the Brazilian tax system

Fontes de fibra na alimentação do pacu: desempenho, composição corporal e morfometria intestinal

O objetivo deste estudo foi avaliar os efeitos da utilização de diferentes ingredientes fibrosos nas dietas sobre o desempenho, a composição corporal e a morfometria intestinal de juvenis de pacu. Foram avaliadas cinco dietas isoproteicas (23% de proteína digestível), isoenergéticas (3250kcal de energia digestível/kg) e isofibrosas (9% de fibra bruta), sendo a principal fonte fibrosa de cada constituída por farelo de soja, casca de soja, farelo de girassol e polpa cítrica; esta última em dois níveis de inclusão (30 e 45%). Foram utilizados 300 juvenis de pacu (25,12±0,78 gramas), alojados em 25 aquários (200 litros). Os melhores resultados de crescimento e conversão alimentar foram obtidos com as dietas contendo farelo de soja e farelo de girassol. As dietas contendo casca de soja e polpa cítrica prejudicaram o desempenho dos juvenis de pacu, e o efeito negativo foi acentuado com o aumento da inclusão de polpa cítrica. Além disto, somente nos peixes alimentados com a dieta com 45% de polpa cítrica foi observada diminuição na densidade de vilosidades por área no epitélio intestinal. A partir dos resultados obtidos, pode-se concluir que alguns ingredientes fibrosos podem afetar negativamente o desempenho e as características do epitélio intestinal de juvenis de pacu.

Cultivo de híbridos de pimentão amarelo em fibra da casca de coco

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Consumo e dinâmica ruminal da fibra em detergente neutro em bovinos em pastejo no período das águas recebendo suplementação com nitrogênio não-proteico e/ou proteína verdadeira

Objetivou-se avaliar o efeito de diferentes relações entre proteína verdadeira e nitrogênio não-proteico sobre o consumo e a dinâmica de trânsito e degradação ruminal da fibra em detergente neutro (FDN) da forragem em bovinos em pastejo durante o período das águas. Foram utilizados cinco novilhos mestiços Holandês × Zebu, castrados, com peso corporal inicial de 335±35 kg fistulados no rúmen e no abomaso. Os tratamentos foram: controle (somente pasto); e suplementos com ureia; com 2/3 de compostos nitrogenados oriundos da ureia e 1/3 de compostos nitrogenados oriundos da albumina; com 1/3 de compostos nitrogenados oriundos da ureia e 2/3 de compostos nitrogenados oriundos da albumina; e com albumina. Foram fornecidos 200 g/dia de proteína bruta (PB) a partir dos suplementos. O experimento foi conduzido segundo delineamento em quadrado latino 5 × 5, com cinco períodos experimentais de 15 dias. Não foram observados efeitos da suplementação sobre o consumo voluntário, com exceção do consumo de PB, que aumentou com a suplementação. A substituição da ureia por albumina nos suplementos teve efeito linear sobre o consumo de PB. Os consumos dos demais componentes da dieta não foram afetados pela composição dos suplementos. Nenhum efeito foi observado sobre a taxa de passagem ruminal de compostos fibrosos. O fornecimento de suplementos ampliou, em média, a estimativa da taxa comum de latência e degradação da FDN. Contudo, não houve efeito da alteração na composição dos suplementos sobre este parâmetro. A suplementação de bovinos com fontes de compostos nitrogenados degradáveis no rúmen proteicos ou não-proteicos durante o período das águas não afeta o consumo voluntário de pasto.

Avaliação da determinação da fibra em detergente neutro e da fibra em detergente ácido pelo sistema ANKOM

O objetivo do trabalho foi comparar os valores de fibra em detergente neutro (FDN) e os de fibra em detergente ácido (FDA) obtidos com o equipamento ANKOM e pelo método convencional (Van Soest). No primeiro ensaio foram analisados cinco materiais diferentes (cana-de-açúcar, capim-braquiária, silagem de milho, polpa cítrica e fezes bovina) e testados quatro tipos de saquinhos para filtragem de amostra. O delineamento experimental foi em blocos casualizados, em um fatorial 5x4 (cinco materiais diferentes e quatro tipos de saquinhos de filtragem), com três repetições. As médias obtidas foram comparadas àquelas obtidas com método convencional. No segundo ensaio procurou-se avaliar o efeito da quantidade de amostra por saquinho (0,5; 0,8 e 1,0 g) sobre os teores de FDN e FDA em três tipos de alimentos, utilizando o ANKOM. Neste ensaio, o delineamento experimental foi em blocos casualizados em esquema fatorial 3x3 (três alimentos x três quantidades), com três repetições. Os tipos de saquinhos de filtragem utilizados não influenciaram os teores de FDN nos diferentes alimentos, com exceção das fezes, cujos saquinhos de náilon resultaram em concentrações de FDN inferiores. Não houve diferença entre os valores de FDN e FDA, obtidos pelo equipamento ANKOM ou pelo convencional, para os alimentos estudados, com exceção da polpa cítrica, cujo valor médio de FDA pelo ANKOM foi inferior àquele obtido pelo método convencional. A quantidade não exerceu efeito sobre a concentração de FDN dos alimentos analisados no equipamento ANKOM.