Stable oxygen isotope composition of benthic foraminifera from sediments of the Skagerrak, North Sea

Benthic foraminiferal tests of a sediment core from southwestern Skagerrak (northeastern North Sea, 420 m water depth) were investigated for their ratio of stable oxygen isotopes. During modern times sudden drops in temperature and salinity of Skagerrak deep waters point to advection-induced cascades of colder and denser central North Sea waters entering the Skagerrak. These temperature drops, which are recorded in benthic foraminiferal tests via the stable oxygen isotopic composition, were used to reconstruct deep-water renewal in the Skagerrak. In a second step we will show that, at least during the last 1200 years, Skagerrak deep-water renewal is triggered by the negative phase of the North Atlantic Oscillation (NAO). The NAO exerts a strong influence on the climate of northwestern Europe. It is currently under debate if the long-term variability of the NAO is capable of influencing Northern Hemisphere climate on long timescales. The data presented here cannot reinforce these speculations. Our data show that most of the 'Little Ice Age' was dominated by comparably warm deep-water temperatures. However, we did find extraordinary strong temperature differences between central North Sea waters and North Atlantic water masses during this time interval.

Ice rafted debris in the Nordic Seas

A continuous 3.5 Myr IRD record was produced from Ocean Drilling Program (ODP) Site 907. A timescale based on magnetic polarity chrons, oxygen isotope stratigraphy (for the last 1Myr) and orbital tuning was developed. The record documents a stepwise inception of large-scale glacial cycles in the Nordic Seas region, the first being a marked expansion of the Greenland ice sheet at 3.3 Ma. A second step occurred at 2.74 Ma by an expansion of large scale ice sheets in the Northern Hemisphere. Ice sheet variability around the Nordic Seas was tightly coupled to global ice volume over the past 3.3 Myr. Between 3 and 1 Ma, most of the variance of the IRD signal is in the 41 kyr band, whereas the last 1 Myr is characterized by stronger 100 kyr variance. The Gamma Ray Porosity Evaluator (GRAPE) density record is closely linked with IRD variations and documents sub orbital variability resembling the late Quaternary Heinrich/Bond cycles.

Scaling up the production of biogenic magnetite nanoparticles

Although there are numerous examples of large-scale commercial microbial synthesis routes for organic bioproducts, few studies have addressed the obvious potential for microbial systems to produce inorganic functional biomaterials at scale. Here we address this by focusing on the production of nano-scale biomagnetite particles by the Fe(III)-reducing bacterium Geobacter sulfurreducens, which was scaled-up successfully from lab-scale to pilot plant-scale production, whilst maintaining the surface reactivity and magnetic properties which make this material well suited to commercial exploitation. At the largest scale tested, the bacterium was grown in a 50 L bioreactor, harvested and then inoculated into a buffer solution containing Fe(III)-oxyhydroxide and an electron donor and mediator, which promoted the formation of magnetite in under 24 hours. This procedure was capable of producing up to 120 g biomagnetite. The particle size distribution was maintained between 10 and 15 nm during scale-up of this second step from 10 ml to 10 L, with conserved magnetic properties and surface reactivity; the latter demonstrated by the reduction of Cr(VI). The process presented provides an environmentally benign route to magnetite production and serves as an alternative to harsher synthetic techniques, with the clear potential to be used to produce kg to tonne quantities.

Miocene to Quaternary paleoenvironments and uplift history on the mid Norwegian shelf

Based on benthic and planktic foraminifera, Bolboforma, oxygen isotope measurements and seismic data, major changes in Miocene, Pliocene and Pleistocene paleoenvironments on the mid Norwegian shelf are discussed and a possible scenario of the late Cenozoic uplift history is given. The dating of the Neogene sequence has been done using foraminifera and Bolboforma. Four main assemblage zones have been identified with nine distinct subzones. Most of the Miocene sequence is preserved. The lower Miocene sediments contain only siliceous microfossils. A period of high fertility and upwelling in the study area prevailed. The early Miocene-early mid Miocene (15 Ma?) change from a siliceous to a calcareous rich microfauna, dominated by Nonion barleeanum, can be related to increased surface-water circulation due to overflow across the Iceland-Faeroe ridge. During the Miocene the temperature decreased in the study area. Evidence of increased amounts of coarser sediments may suggest that an uplift of the mainland areas occurred during the mid-late Miocene. Lower Pliocene sediments contain a foraminiferal fauna that seems to occur in slightly colder conditions than the late Miocene fauna suggesting a further cooling. Possibly, Arctic waters entered the study area in the early Pliocene. A very marked change in lithology (from compacted claystone to unconsolidated diamicton), fauna (from deep dwelling to shallow dwelling species) and seismic signature (from flat lying reflectors to prograding clinoforms) occurs during the mid?-late Pliocene. A two step cooling trend is indicated by the microfauna of these prograding wedges. (1) The first wedge buildups might have been associated with an uplift of the mainland during the early late Pliocene (mid Pliocene, ca. 4 Ma). However, the age determination is somewhat uncertain and may very well be of late Pliocene age. (2) The second step of wedge buildup is associated with a glacial phase where the dominating microfauna exists of arctic species. Large continental ice sheets might have occurred at this time reaching coastal areas and that possibly many of the geomorphological features such as the strandflat were made during this episode. The Pleistocene epoch is represented by an increased percentage of boreal foraminifera intermingled with high arctic species which indicates that interglacial-glacial cycles prevailed and the dynamics of the glacier system changed.

Output processing and automatic reporting with Stata

This talk illustrates how results from various Stata commands can be processed efficiently for inclusion in customized reports. A two-step procedure is proposed in which results are gathered and archived in the first step and then tabulated in the second step. Such an approach disentangles the tasks of computing results (which may take long) and preparing results for inclusion in presentations, papers, and reports (which you may have to do over and over). Examples using results from model estimation commands and various other Stata commands such as tabulate, summarize, or correlate are presented. Users will also be shown how to dynamically link results into word processors or into LaTeX documents.

Recent developments in output processing

This tutorial will show how results from various Stata commands can be processed efficiently for inclusion in customized reports. A two-step procedure is proposed in which results are gathered and archived in the first step and then tabulated in the second step. Such an approach disentangles the tasks of computing results (which may take long) and preparing results for inclusion in presentations, papers, and reports (which you may have to do over and over). Examples using results from model estimation commands and also various other Stata commands such as tabulate, summarize, or correlate are presented. Furthermore, this tutorial shows how to dynamically link results into word processors or into LaTeX documents.

Proyecto de viabilidad de una planta de tratamiento para mineral de estaño y tántalo

El proyecto tiene como objeto definir la viabilidad de explotación de un importante yacimiento de Estaño y Tántalo que se encuentra en una formación geológica de base pegmatítica situada en el norte de España. En base a las reservas calculadas, se define la capacidad de tratamiento de la planta de procesamiento del mineral para un periodo de explotación de 10 años. Como primer paso se estudian los ensayos de caracterización y concentración realizados en laboratorio a partir de muestras de mano representativas del mineral así como otros en planta piloto llevados a cabo anteriormente. Una vez definida la recuperación del Estaño y Tántalo se procede al diseño conceptual del proceso. Posteriormente se desarrolla un diseño e ingeniería preliminar más aproximados, a partir de los cuales se evalúan los costes de equipos y operacionales que, en base a los retornos por la venta de los concentrados, permitirán calcular la rentabilidad del proyecto y riesgos de la inversión. ABSTRACT The purpose of this project is to define the feasibility of mining a major deposit of tin and tantalum found in a pegmatite formation in northern Spain. Based on the estimated reserves, the operating capacity for mining and mineral processing plant was defined for a period of 10 years. As a first step for the development, a research program for characterization and concentration of the ore, were performed in the laboratory based on representative samples from the deposit. In addition, previous pilot plant results were also taken into account. Once determined the recovery of tin and tantalum, the conceptual design process was defined. As a second step, it was developed a preliminary design and engineering, from which the capital and operating costs were estimated .By means of the calculated returns from the sale of concentrates, the profitability of the project and investment risks were finally assessed

Estudio de hormigones reciclados no estructurales fabricados con árido reciclado mixto : propiedades mecánicas y expansión debida al contenido de sulfatos

El objetivo principal de este trabajo de investigación es estudiar las posibilidades de utilización del árido reciclado mixto para un hormigón reciclado en aplicaciones no estructurales, justificando mediante la experimentación la validez para esta aplicación, tanto del árido reciclado como del hormigón reciclado. Esta tesis se centró en los aspectos más restrictivos y limitativos en la utilización de los áridos mixtos en hormigón reciclado, basándose tanto en la normativa internacional existente como en los resultados obtenidos en los estudios bibliográficos consultados. La primera tarea realizada fue la caracterización completa de las propiedades del árido reciclado mixto, recogiendo especialmente los siguientes aspectos: granulometría, contenido de finos, absorción y densidades, composición del árido reciclado, índice de lajas, coeficiente de Los Ángeles, partículas ligeras y contenido de sulfatos. De este estudio de los áridos reciclados, se han destacado relaciones entre las propiedades. Las diferentes correlaciones permiten proponer criterios de calidad de un árido reciclado mixto para un hormigón reciclado. Se ha elegido un árido reciclado mixto entre los estudiados, de características límite admisibles, para obtener resultados conservadores sobre el hormigón reciclado fabricado con él. En una segunda etapa, se ha realizado un estudio de dosificación completo del hormigón reciclado, evaluando la consistencia del hormigón en estado fresco y la resistencia a compresión del hormigón en estado endurecido y se ha comparado con las mismas propiedades de un hormigón convencional. Se ha analizado la capacidad de absorción del árido conseguida con los métodos de presaturación empleados y en función de su estado de humedad, para poder evaluar las relaciones agua/cemento totales y efectivas del hormigón. Se ha estudiado el efecto de estos dos parámetros tanto en la consistencia como en la resistencia del hormigón reciclado. Finalmente, se ha estudiado el hormigón fabricado con un 50% y 100% de una partida de árido reciclado mixto de calidad admisible y se han ensayado las siguientes propiedades: consistencia, resistencia a compresión, resistencia a tracción indirecta, módulo de elasticidad dinámico, cambios de longitud, porosidad abierta y microscopía. Para analizar el efecto de los sulfatos, se han añadido artificialmente cantidades de yeso controladas en el hormigón reciclado. Se fabricaron hormigones con dos tipos de cemento, un cemento CEM I 42,5 R con elevado contenido de C3A, que debería dar lugar a expansiones mayores y un cemento con adiciones puzolánicas CEM II A-P 42,5 R, que atenuaría el comportamiento expansivo en el hormigón. Los resultados finales indican que la utilización del árido reciclado mixto en proporciones de hasta un 50%, permiten cubrir la gama de resistencias más exigentes dentro del hormigón no estructural. El contenido de sulfatos puede variar desde un 0,8% hasta un 1,9%, según el tipo de cemento y la proporción de sustitución del árido natural por árido reciclado mixto. Tanto en el caso del árido reciclado como en el hormigón, se ha realizado un estudio comparativo entre el conjunto de datos recopilados en la bibliografía y los obtenidos en este estudio experimental. En varias propiedades del hormigón reciclado, se han comparado los resultados con las fórmulas de la Instrucción EHE-08, para establecer unos coeficientes de corrección a aplicar a un hormigón reciclado con fines no estructurales. The main objective of this investigation work is to study the possibilities of using recycled mixed aggregate for a recycled concrete in non structural applications, justifying by means of experimentation both the validity of the recycled aggregate and recycled concrete. This thesis focused on the most restrictive and limiting aspects in the mixed aggregate use in recycled concrete, on the basis of the international standards as well on the results obtained in the bibliographic studies consulted. The first task achieved was the complete charcaterization of the mixed recycled aggregate properties, specially the following aspects: grain size analysis, fines content, absorption and densities, recycled aggregate composition, flakiness index, Los Angeles coefficient, lightweight particles and sulphate content. From this study, correlations between the properties were highlighted. The different correlations make possible to propose quality criterions for recycled mixed aggregate in concrete. Among the recycled aggregates studied, one of acceptable characteristics but near the limits established, was chosen to obtain conservative results in the recycled concrete made with it. In a second step, a complete recycled concrete mix design was made, to evaluate concrete consistency in the fresh state and concrete compressive strength in the hardened state and its properties were compared to those of a control concrete. The aggregate absorption capacity was analized with the presaturation methods achieved and in function of its state of humidity, to evaluate the total and effective water/cement ratios. The effect of these two parameters, both in consistency and compressive strength of recycled concrete, was studied. Finally, the concrete made with 50% and 100% of the elected recycled mixed aggregate was studied and the following concrete properties were tested: consistency, compressive strength, tensile strength, dynamic modulus of elasticity, length changes, water absorption under vacuum and microscopy. To analize the effect of sulphate content, some controlled quantities of gypsum were artificially added to the recycled concrete. Concretes with two types of cement were made, a cement CEM I 42,5 R with a high content of C3A, that would lead to major expansions and a cement with puzzolanic additions CEM II A-P 42,5 R that would lower the expansive behaviour of concrete. The final results indicate that the use of mixed recycled aggregate in proportions up to 50% make possible to cover the overall demanding strengths within the non structural concrete. Sulphates content can range between 0,8% and 1,9%, in function of the type of cement and the proportion of natural aggregate replacement by mixed recycled one. Both in the case of recycled aggregate and concrete, a comparative study was made between the data coming from the bibliography and those obtained in the experimental study. In several recycled concrete properties, the results were compared to the formulas of Spanish Instruction of Structural Concrete (Instruction EHE-08), to establish some correction coefficients to apply for a non structural recycled concrete.

Seismic Hazard and Ground Motion Characterization at the Itoiz Dam (Northern Spain).

This paper presents a new hazard-consistent ground motion characterization of the Itoiz dam site, located in Northern Spain. Firstly, we propose a methodology with different approximation levels to the expected ground motion at the dam site. Secondly, we apply this methodology taking into account the particular characteristics of the site and of the dam. Hazard calculations were performed following the Probabilistic Seismic Hazard Assessment method using a logic tree, which accounts for different seismic source zonings and different ground-motion attenuation relationships. The study was done in terms of peak ground acceleration and several spectral accelerations of periods coinciding with the fundamental vibration periods of the dam. In order to estimate these ground motions we consider two different dam conditions: when the dam is empty (T = 0.1 s) and when it is filled with water to its maximum capacity (T = 0.22 s). Additionally, seismic hazard analysis is done for two return periods: 975 years, related to the project earthquake, and 4,975 years, identified with an extreme event. Soil conditions were also taken into account at the site of the dam. Through the proposed methodology we deal with different forms of characterizing ground motion at the study site. In a first step, we obtain the uniform hazard response spectra for the two return periods. In a second step, a disaggregation analysis is done in order to obtain the controlling earthquakes that can affect the dam. Subsequently, we characterize the ground motion at the dam site in terms of specific response spectra for target motions defined by the expected values SA (T) of T = 0.1 and 0.22 s for the return periods of 975 and 4,975 years, respectively. Finally, synthetic acceleration time histories for earthquake events matching the controlling parameters are generated using the discrete wave-number method and subsequently analyzed. Because of the short relative distances between the controlling earthquakes and the dam site we considered finite sources in these computations. We conclude that directivity effects should be taken into account as an important variable in this kind of studies for ground motion characteristics.

Approximate entropy of network parameters

We study the notion of approximate entropy within the framework of network theory. Approximate entropy is an uncertainty measure originally proposed in the context of dynamical systems and time series. We first define a purely structural entropy obtained by computing the approximate entropy of the so-called slide sequence. This is a surrogate of the degree sequence and it is suggested by the frequency partition of a graph. We examine this quantity for standard scale-free and Erdös-Rényi networks. By using classical results of Pincus, we show that our entropy measure often converges with network size to a certain binary Shannon entropy. As a second step, with specific attention to networks generated by dynamical processes, we investigate approximate entropy of horizontal visibility graphs. Visibility graphs allow us to naturally associate with a network the notion of temporal correlations, therefore providing the measure a dynamical garment. We show that approximate entropy distinguishes visibility graphs generated by processes with different complexity. The result probes to a greater extent these networks for the study of dynamical systems. Applications to certain biological data arising in cancer genomics are finally considered in the light of both approaches.

Hybrid incremental modeling based on least squares and fuzzy K-NN for monitoring tool wear in turning processes

There is now an emerging need for an efficient modeling strategy to develop a new generation of monitoring systems. One method of approaching the modeling of complex processes is to obtain a global model. It should be able to capture the basic or general behavior of the system, by means of a linear or quadratic regression, and then superimpose a local model on it that can capture the localized nonlinearities of the system. In this paper, a novel method based on a hybrid incremental modeling approach is designed and applied for tool wear detection in turning processes. It involves a two-step iterative process that combines a global model with a local model to take advantage of their underlying, complementary capacities. Thus, the first step constructs a global model using a least squares regression. A local model using the fuzzy k-nearest-neighbors smoothing algorithm is obtained in the second step. A comparative study then demonstrates that the hybrid incremental model provides better error-based performance indices for detecting tool wear than a transductive neurofuzzy model and an inductive neurofuzzy model.

Aplicación móvil iOS de información a estudiantes universitarios

Reconociendo que podía ser útil para los alumnos una aplicación móvil para que pudieran acceder a información relacionada con sus estudios de forma rápida y sobre la marcha, se decide realizar una prueba de concepto cuyo resultado satisfactorio conduce a dar el siguiente paso en el desarrollo de la aplicación móvil. En este contexto es donde se enmarca el proyecto “Desarrollo de una aplicación móvil iOS de información a estudiantes universitarios” que tiene como finalidad aprovechar las ventajas que nos brindan las nuevas tecnologías. En el prototipo de aplicación móvil fueron encontrados problemas de mantenibilidad y la versión del sistema operativo había quedado obsoleta. Por lo tanto el primer paso fue refactorizar todos los paquetes del proyecto, después de esto fue necesario crear un estándar de codificación y una documentación del proyecto. El segundo paso fue adaptar el proyecto a la última versión del sistema operativo, iOS 7, siguiendo la guía de transición de la interfaz de usuario de Apple. Además de todo esto, había nuevas funcionalidades que incluir al prototipo, estas nuevas funcionalidades han sido probadas en una evaluación con usuarios para obtener comentarios y sugerencias de los alumnos universitarios para mejorar la aplicación en la medida de lo posible. ----ABSTRACT----Recognizing that could be useful a mobile app for students to enable them to access information related to their studies quickly and on the go, it was decided to perform a proof of concept whose satisfactory results leads to take the next step in the development of the mobile app. In this context is where the project “Desarrollo de una aplicación móvil iOS de información a estudiantes universitarios” takes part whose aim is to exploit the advantages offered by the new technologies. Maintenance problems were found in the mobile app prototype and the operating system version was outdated. So the first step was to refactor all the Project packages, after that it was necessary to create a coding standard and a Project documentation. The second step was to adapt the project to the latest versión of the operating system, iOS7, following the Apple UI transition guide. In addition to all of this, there were new features to include to the prototype, these new features have been tested in an user evaluation to obtain feedback and suggestions from college students to improve the app as far as possible.

Reconocimiento de gestos basado en acelerómetros

En los últimos años, ha crecido de forma significativa el interés por la utilización de dispositivos capaces de reconocer gestos humanos. En este trabajo, se pretenden reconocer gestos manuales colocando sensores en la mano de una persona. El reconocimiento de gestos manuales puede ser implementado para diversos usos y bajo diversas plataformas: juegos (Wii), control de brazos robóticos, etc. Como primer paso, se realizará un estudio de las actuales técnicas de reconocimiento de gestos que utilizan acelerómetros como sensor de medida. En un segundo paso, se estudiará como los acelerómetros pueden utilizarse para intentar reconocer los gestos que puedan realizar una persona (mover el brazo hacia un lado, girar la mano, dibujar un cuadrado, etc.) y los problemas que de su utilización puedan derivarse. Se ha utilizado una IMU (Inertial Measurement Unit) como sensor de medida. Está compuesta por tres acelerómetros y tres giróscopos (MTi-300 de Xsens). Con las medidas que proporcionan estos sensores se realiza el cálculo de la posición y orientación de la mano, representando esta última en función de los ángulos de Euler. Un aspecto importante a destacar será el efecto de la gravedad en las medidas de las aceleraciones. A través de diversos cálculos y mediante la ayuda de los giróscopos se podrá corregir dicho efecto. Por último, se desarrollará un sistema que identifique la posición y orientación de la mano como gestos reconocidos utilizando lógica difusa. Tanto para la adquisición de las muestras, como para los cálculos de posicionamiento, se ha desarrollado un código con el programa Matlab. También, con este mismo software, se ha implementado un sistema de lógica difusa con la que se realizará el reconocimiento de los gestos, utilizando la herramienta FIS Editor. Las pruebas realizadas han consistido en la ejecución de nueve gestos por diferentes personas teniendo una tasa de reconocimiento comprendida entre el 90 % y 100 % dependiendo del gesto a identificar. ABSTRACT In recent years, it has grown significantly interest in the use of devices capable of recognizing human gestures. In this work, we aim to recognize hand gestures placing sensors on the hand of a person. The recognition of hand gestures can be implemented for different applications on different platforms: games (Wii), control of robotic arms ... As a first step, a study of current gesture recognition techniques that use accelerometers and sensor measurement is performed. In a second step, we study how accelerometers can be used to try to recognize the gestures that can make a person (moving the arm to the side, rotate the hand, draw a square, etc...) And the problems of its use can be derived. We used an IMU (Inertial Measurement Unit) as a measuring sensor. It comprises three accelerometers and three gyroscopes (Xsens MTI-300). The measures provided by these sensors to calculate the position and orientation of the hand are made, with the latter depending on the Euler angles. An important aspect to note is the effect of gravity on the measurements of the accelerations. Through various calculations and with the help of the gyroscopes can correct this effect. Finally, a system that identifies the position and orientation of the hand as recognized gestures developed using fuzzy logic. Both the acquisition of samples to calculate position, a code was developed with Matlab program. Also, with the same software, has implemented a fuzzy logic system to be held with the recognition of gestures using the FIS Editor. Tests have involved the execution of nine gestures by different people having a recognition rate between 90% and 100% depending on the gesture to identify.

Detección de grietas en placas con técnicas multifrecuencia

Safety is one of the most important feature in the aviation industry, and this involves too many factors. One of these is the aircraft maintenance. Over time, the procedures have been changing, and improving themselves. Non Destructive Testing (NDT) appeared in the late 19th century as a great option, because it enabled to inspect any structure without damaging it. Nowadays, there are several kinds of NDT, but ultrasound is one of the most widely used. This Master Thesis is devoted to an innovative ultrasound technique for crack detection. A technique, whose main aim lies in getting a good location of defects from a few measures, breaking with the currently widespread methods, as phased array. It is not necessary to use trains of waves, only discrete excitations, which means a great saving of time and energy. This work is divided into two steps: the first is to develop a multiphysics simulator, which is able to solve linear elasticity 3D problems (via Finite Element Method, FEM). This simulator allows to obtain in a computationally efficient way the displacement field for different frequencies and excitations. The solution of this elastic problem is needed to be used in the second step, which consists of generating a code that implements a mathematical tool named topological derivative, allowing to locate defects in the studied domain. In this work, the domain is a plate, and the defect is a hidden spherical void. The simulator has been developed using open source software (Elmer, Gmsh, ...), achieving a highly versatile simulator, which allows to change the configuration easily: domain size and shape, number and position of transducers, etc. Just one comercial software is used, Matlab. It is used to implement the topological derivative. In this work, the performance of the method is tested in several examples comparing the results when one or more frequencies are considered for different configurations of emisors/receptors.

High power beam dump project for the accelerator prototype LIPAc: Cooling design and analysis

En el campo de la fusión nuclear y desarrollándose en paralelo a ITER (International Thermonuclear Experimental Reactor), el proyecto IFMIF (International Fusion Material Irradiation Facility) se enmarca dentro de las actividades complementarias encaminadas a solucionar las barreras tecnológicas que aún plantea la fusión. En concreto IFMIF es una instalación de irradiación cuya misión es caracterizar materiales resistentes a condiciones extremas como las esperadas en los futuros reactores de fusión como DEMO (DEMOnstration power plant). Consiste de dos aceleradores de deuterones que proporcionan un haz de 125 mA y 40 MeV cada uno, que al colisionar con un blanco de litio producen un flujo neutrónico intenso (1017 neutrones/s) con un espectro similar al de los neutrones de fusión [1], [2]. Dicho flujo neutrónico es empleado para irradiar los diferentes materiales candidatos a ser empleados en reactores de fusión, y las muestras son posteriormente examinadas en la llamada instalación de post-irradiación. Como primer paso en tan ambicioso proyecto, una fase de validación y diseño llamada IFMIFEVEDA (Engineering Validation and Engineering Design Activities) se encuentra actualmente en desarrollo. Una de las actividades contempladas en esta fase es la construcción y operación de una acelarador prototipo llamado LIPAc (Linear IFMIF Prototype Accelerator). Se trata de un acelerador de deuterones de alta intensidad idéntico a la parte de baja energía de los aceleradores de IFMIF. Los componentes del LIPAc, que será instalado en Japón, son suministrados por diferentes países europeos. El acelerador proporcionará un haz continuo de deuterones de 9 MeV con una potencia de 1.125 MW que tras ser caracterizado con diversos instrumentos deberá pararse de forma segura. Para ello se requiere un sistema denominado bloque de parada (Beam Dump en inglés) que absorba la energía del haz y la transfiera a un sumidero de calor. España tiene el compromiso de suministrar este componente y CIEMAT (Centro de Investigaciones Energéticas Medioambientales y Tecnológicas) es responsable de dicha tarea. La pieza central del bloque de parada, donde se para el haz de iones, es un cono de cobre con un ángulo de 3.5o, 2.5 m de longitud y 5 mm de espesor. Dicha pieza está refrigerada por agua que fluye en su superficie externa por el canal que se forma entre el cono de cobre y otra pieza concéntrica con éste. Este es el marco en que se desarrolla la presente tesis, cuyo objeto es el diseño del sistema de refrigeración del bloque de parada del LIPAc. El diseño se ha realizado utilizando un modelo simplificado unidimensional. Se han obtenido los parámetros del agua (presión, caudal, pérdida de carga) y la geometría requerida en el canal de refrigeración (anchura, rugosidad) para garantizar la correcta refrigeración del bloque de parada. Se ha comprobado que el diseño permite variaciones del haz respecto a la situación nominal siendo el flujo crítico calorífico al menos 2 veces superior al nominal. Se han realizado asimismo simulaciones fluidodinámicas 3D con ANSYS-CFX en aquellas zonas del canal de refrigeración que lo requieren. El bloque de parada se activará como consecuencia de la interacción del haz de partículas lo que impide cualquier cambio o reparación una vez comenzada la operación del acelerador. Por ello el diseño ha de ser muy robusto y todas las hipótesis utilizadas en la realización de éste deben ser cuidadosamente comprobadas. Gran parte del esfuerzo de la tesis se centra en la estimación del coeficiente de transferencia de calor que es determinante en los resultados obtenidos, y que se emplea además como condición de contorno en los cálculos mecánicos. Para ello por un lado se han buscado correlaciones cuyo rango de aplicabilidad sea adecuado para las condiciones del bloque de parada (canal anular, diferencias de temperatura agua-pared de decenas de grados). En un segundo paso se han comparado los coeficientes de película obtenidos a partir de la correlación seleccionada (Petukhov-Gnielinski) con los que se deducen de simulaciones fluidodinámicas, obteniendo resultados satisfactorios. Por último se ha realizado una validación experimental utilizando un prototipo y un circuito hidráulico que proporciona un flujo de agua con los parámetros requeridos en el bloque de parada. Tras varios intentos y mejoras en el experimento se han obtenido los coeficientes de película para distintos caudales y potencias de calentamiento. Teniendo en cuenta la incertidumbre de las medidas, los valores experimentales concuerdan razonablemente bien (en el rango de 15%) con los deducidos de las correlaciones. Por motivos radiológicos es necesario controlar la calidad del agua de refrigeración y minimizar la corrosión del cobre. Tras un estudio bibliográfico se identificaron los parámetros del agua más adecuados (conductividad, pH y concentración de oxígeno disuelto). Como parte de la tesis se ha realizado asimismo un estudio de la corrosión del circuito de refrigeración del bloque de parada con el doble fin de determinar si puede poner en riesgo la integridad del componente, y de obtener una estimación de la velocidad de corrosión para dimensionar el sistema de purificación del agua. Se ha utilizado el código TRACT (TRansport and ACTivation code) adaptándalo al caso del bloque de parada, para lo cual se trabajó con el responsable (Panos Karditsas) del código en Culham (UKAEA). Los resultados confirman que la corrosión del cobre en las condiciones seleccionadas no supone un problema. La Tesis se encuentra estructurada de la siguiente manera: En el primer capítulo se realiza una introducción de los proyectos IFMIF y LIPAc dentro de los cuales se enmarca esta Tesis. Además se describe el bloque de parada, siendo el diseño del sistema de rerigeración de éste el principal objetivo de la Tesis. En el segundo y tercer capítulo se realiza un resumen de la base teórica así como de las diferentes herramientas empleadas en el diseño del sistema de refrigeración. El capítulo cuarto presenta los resultados del relativos al sistema de refrigeración. Tanto los obtenidos del estudio unidimensional, como los obtenidos de las simulaciones fluidodinámicas 3D mediante el empleo del código ANSYS-CFX. En el quinto capítulo se presentan los resultados referentes al análisis de corrosión del circuito de refrigeración del bloque de parada. El capítulo seis se centra en la descripción del montaje experimental para la obtención de los valores de pérdida de carga y coeficiente de transferencia del calor. Asimismo se presentan los resultados obtenidos en dichos experimentos. Finalmente encontramos un capítulo de apéndices en el que se describen una serie de experimentos llevados a cabo como pasos intermedios en la obtención del resultado experimental del coeficiente de película. También se presenta el código informático empleado para el análisis unidimensional del sistema de refrigeración del bloque de parada llamado CHICA (Cooling and Heating Interaction and Corrosion Analysis). ABSTRACT In the nuclear fusion field running in parallel to ITER (International Thermonuclear Experimental Reactor) as one of the complementary activities headed towards solving the technological barriers, IFMIF (International Fusion Material Irradiation Facility) project aims to provide an irradiation facility to qualify advanced materials resistant to extreme conditions like the ones expected in future fusion reactors like DEMO (DEMOnstration Power Plant). IFMIF consists of two constant wave deuteron accelerators delivering a 125 mA and 40 MeV beam each that will collide on a lithium target producing an intense neutron fluence (1017 neutrons/s) with a similar spectra to that of fusion neutrons [1], [2]. This neutron flux is employed to irradiate the different material candidates to be employed in the future fusion reactors, and the samples examined after irradiation at the so called post-irradiative facilities. As a first step in such an ambitious project, an engineering validation and engineering design activity phase called IFMIF-EVEDA (Engineering Validation and Engineering Design Activities) is presently going on. One of the activities consists on the construction and operation of an accelerator prototype named LIPAc (Linear IFMIF Prototype Accelerator). It is a high intensity deuteron accelerator identical to the low energy part of the IFMIF accelerators. The LIPAc components, which will be installed in Japan, are delivered by different european countries. The accelerator supplies a 9 MeV constant wave beam of deuterons with a power of 1.125 MW, which after being characterized by different instruments has to be stopped safely. For such task a beam dump to absorb the beam energy and take it to a heat sink is needed. Spain has the compromise of delivering such device and CIEMAT (Centro de Investigaciones Energéticas Medioambientales y Tecnológicas) is responsible for such task. The central piece of the beam dump, where the ion beam is stopped, is a copper cone with an angle of 3.5o, 2.5 m long and 5 mm width. This part is cooled by water flowing on its external surface through the channel formed between the copper cone and a concentric piece with the latter. The thesis is developed in this realm, and its objective is designing the LIPAc beam dump cooling system. The design has been performed employing a simplified one dimensional model. The water parameters (pressure, flow, pressure loss) and the required annular channel geometry (width, rugoisty) have been obtained guaranteeing the correct cooling of the beam dump. It has been checked that the cooling design allows variations of the the beam with respect to the nominal position, being the CHF (Critical Heat Flux) at least twice times higher than the nominal deposited heat flux. 3D fluid dynamic simulations employing ANSYS-CFX code in the beam dump cooling channel sections which require a more thorough study have also been performed. The beam dump will activateasaconsequenceofthe deuteron beam interaction, making impossible any change or maintenance task once the accelerator operation has started. Hence the design has to be very robust and all the hypotheses employed in the design mustbecarefully checked. Most of the work in the thesis is concentrated in estimating the heat transfer coefficient which is decisive in the obtained results, and is also employed as boundary condition in the mechanical analysis. For such task, correlations which applicability range is the adequate for the beam dump conditions (annular channel, water-surface temperature differences of tens of degrees) have been compiled. In a second step the heat transfer coefficients obtained from the selected correlation (Petukhov- Gnielinski) have been compared with the ones deduced from the 3D fluid dynamic simulations, obtaining satisfactory results. Finally an experimental validation has been performed employing a prototype and a hydraulic circuit that supplies a flow with the requested parameters in the beam dump. After several tries and improvements in the experiment, the heat transfer coefficients for different flows and heating powers have been obtained. Considering the uncertainty in the measurements the experimental values agree reasonably well (in the order of 15%) with the ones obtained from the correlations. Due to radiological reasons the quality of the cooling water must be controlled, hence minimizing the copper corrosion. After performing a bibligraphic study the most adequate water parameters were identified (conductivity, pH and dissolved oxygen concentration). As part of this thesis a corrosion study of the beam dump cooling circuit has been performed with the double aim of determining if corrosion can pose a risk for the copper beam dump , and obtaining an estimation of the corrosion velocitytodimension the water purification system. TRACT code(TRansport and ACTivation) has been employed for such study adapting the code for the beam dump case. For such study a collaboration with the code responsible (Panos Karditsas) at Culham (UKAEA) was established. The work developed in this thesis has supposed the publication of three articles in JCR journals (”Journal of Nuclear Materials” y ”Fusion Engineering and Design”), as well as presentations in more than four conferences and relevant meetings.