垃圾渗滤液场外硝化－原位反硝化脱氮协同填埋场温室气体减排

垃圾卫生填埋是国内外城市垃圾的主要处置方法。垃圾渗滤液是渗入填埋场垃圾的降水混合垃圾降解过程中产生的物质而形成的混合物，是垃圾填埋场向环境排放的主要污染物。渗滤液由于其所含高浓度有机和无机污染物，且其中很多物质有生物毒性或难生物降解，难于治理。特别是到填埋晚期，渗滤液中高浓度的氨氮更是增加了治理的难度。渗滤液场外硝化－原位反硝化是填埋场氮管理的新途径。本文利用从环境中筛选出优势硝化功能菌对渗滤液中的高浓度氨氮进行生物硝化，经硝化后的渗滤液回灌至以垃圾柱模拟的生物反应器填埋场，在填埋场内实现原位反硝化。 上述目标通过以下两部分来实现： 第一部分：渗滤液场外硝化。首先从污水厂的硝化污泥中富集并筛选出硝化功能菌，在模拟氨氮废水中优化。将驯化的硝化功能菌接种于连续式完全混合反应器（CSTR）进行高氨氮渗滤液硝化研究。在200余天的连续运行中，反应器硝化和有机物去除效果良好。在最大氨氮负荷和有机物负荷分别为0.65 g N l-1 d-1 和3.84 g COD l-1 d-1时，氨氮和COD去除率分别高于99%和57%。实验过程中发现，游离氨（FA）和溶解氧（DO）浓度对反应器中亚硝酸盐的积累影响很大。 第二部分：渗滤液原位反硝化。本文利用一个垃圾填充柱模拟生物反应器填埋场，研究了硝化渗滤液回灌对垃圾降解的影响，和回灌的硝化渗滤液中TON（总氧化态氮）对填埋场生物反应器产甲烷作用的影响。最后利用变性梯度凝胶电泳（DGGE）分析了硝化渗滤液回灌对垃圾填埋场菌群结构的影响。结果表明：回灌的TON被完全还原，反硝化为主要反应，最大TON负荷为28.6 mg N kg-1 TS d-1。当垃圾柱TON负荷大于11.4 mg N kg-1 TS d-1时，出现了产甲烷抑制，抑制作用随TON负荷的增加而加强。在此过程中，反硝化逐渐代替产甲烷作用成为填埋场内垃圾降解的主要反应，且更多产生的是清洁的氮气，而非温室气体甲烷。直到实验结束时，回灌硝化渗滤液的垃圾柱的甲烷产量仅相当于对照的2.5%，并且回灌的硝化渗滤液还加速了填埋场垃圾的降解与稳定。通过DGGE进行菌群结构分析发现，由于TON对填埋场的长期作用，反硝化菌增多而产甲烷菌减少。 Landfill still remains the chief method for MSW management around the world. Leachate is a mixture of rainfall permeating through landfill and organic and inorganic matters generated during decomposition of the wastes in the landfills, characterized as highly complicated and refractory wastewater. Ex-situ nitrification and sequential in-situ denitrification represents a novel approach to nitrogen management at landfills. In the present paper, nitrification was carried out in a continuous stirred tank reactor (CSTR) inoculated with nitrifying bacteria which were isolated from municipal WWTP of Chengdu city. The nitrified leachate from CSTR was recirculated to a lab-scale municipal solid waste (MSW) column where in-situ denitrification took place. The above object was achived through two parts as following: First, ex-situ nitification of leachate. After acclimated in simulated wastewater for 3 month, nitrifying bacteria isolated from WWTP nitrifying sludge were added to the CSTR for nitrification. The results over 200 days showed that the maximum nitrogen loading rate (NLR) and the maximum organic loading rate (OLR) was 0.65 g N l-1 d-1 and 3.84 g COD l-1 d-1, respectively. The ammonia and COD removal was over 99% and 57%, respectively. Moreover, the effects of free ammonia (FA) and dissolved oxygen (DO) on nitrification were investigated. Second, in-situ denitrification was studied in a municipal solid waste (MSW) column. Variation of nitrified leachate and its effects on the decomposition of municipal solid waste (MSW) were studied in a lab-scale MSW column to which nitrified leachate was recirculated. Additionally, DGGE was employed to investigate the microbial community of both MSW columns. The results suggested: complete reduction of total oxidized nitrogen (TON) was obtained with maximum TON load of 28.6 mg N kg-1 TS d-1 and denitrification was the main reaction responsible. Methanogenesis inhibition was observed while TON load was over 11.4 mg N kg-1 TS d-1 and the inhibition was enhanced with the increase of TON load. Denitrification gradually took over methanogenesis to become the main reaction responsible for decomposition of MSW while nitrogen gas, a clean byproduct, was generated instead. Till the end of the experiment, the average weekly methane production in the denitrification column was as low as 2.5% of that of the control, and the rate of decompition and stability of MSW was accelerated by the recirculation of the nitrified leachate.Owing to long term exposure of nitrified leachate to landfill, denitrifying bacteria increased and methanogen decreased.

耐酸产甲烷菌的分离及其复合菌剂的研究

本文从成都龙泉垃圾填埋场和宜宾造纸厂分离到耐酸性能优良的高温产甲烷菌RY3和中温产甲烷菌SH4，并将其与实验室现有的利用不同底物的产甲烷菌配伍组合成了复合菌剂。采用活性污泥作为固体附着物，研制出了固体产甲烷菌复合菌剂。 菌株RY3的pH耐受范围为5.5～10.5，最适生长pH 6.0～8.0。菌株RY3为革兰氏阳性，长杆状，多数单生，不运动；菌落浅黄色，形状近圆形；利用H2+CO2或甲酸盐作为唯一碳源生长，不利用乙酸盐，对氯霉素非常敏感。该菌最适生长温度为55℃～65℃，最适NaCl浓度为0～2%。根据形态和生理生化特性及16S rDNA序列分析将其初步定为热自养甲烷热杆菌（Methanothermobacter thermautotrophicus）。添加RY3菌液与仅添加厌氧污泥作为接种物相比一周内可使达到最大产甲烷速率所需时间缩短三分之二，甲烷总产量提高约1.8倍。菌株SH4的生长pH范围5.5～9.5，其对酸碱具有良好的适应性，培养3天后，在初始pH值为6.0～8.0的培养基中甲烷产量相差不大，且基本达到最大产量。SH4革兰氏染色阳性，短杆状，多数单生，不运动；菌落近圆形，微黄；利用H2+CO2或甲酸盐作为唯一碳源生长，不利用乙酸盐，对氯霉素非常敏感。SH4最适生长pH 为7.0，最适生长温度为35℃，最适NaCl浓度为0～1.5%。实验表明，添加SH4菌液与仅添加厌氧污泥作为接种物相比可使产甲烷启动时间缩短三分之一，甲烷总产量亦有大幅提高。从形态和生理生化特征以及16S rDNA序列分析表明SH4为嗜树木甲烷短杆菌（Methanobrevibacter arboriphilus）。 以活性污泥为附着物，与培养基和菌种经搅拌后厌氧发酵可得产甲烷菌固体复合菌剂。固体复合菌剂的pH耐受范围为5.5～9.5，温度耐受范围为15℃～65℃，表明其对环境的适应性较强。以猪粪为底物进行厌氧发酵，接种复合菌剂进行试验，以接种实验室长期富集的产甲烷厌氧污泥作为对照，在20℃时，发酵甲烷浓度与对照基本一致，但每日产气量优于对照，第15天时接种复合菌剂的发酵瓶每日产气量是对照的1.59倍；50℃时达到最大甲烷含量所需时间比对照缩短三分之二，三周内总产气量约为对照的2.7倍，甲烷总产量约为2.8倍。以不加接种物为对照，接种复合菌剂20℃时发酵甲烷含量达到50%约需2周，对照2周内甲烷含量最高仅为4.3%；50℃时接种复合菌剂发酵仅需约1周甲烷含量便可达50%，对照则至少需要2周。 In this paper, high-temperature Methanogen RY3 and middle-temperature SH4 were isolated from Chengdu Longquan refuse landfill and Yibin paper mill. They could be used to make compound inoculum that producing methane with the existing Methanogens utilized different substrate. With using anaerobic activated sludge be solid fixture, the process had been designed to produce solid compound inoculum. Strain RY3 possessed excellent capacity of acid and alkali-tolerant. The pH-tolerant scale of RY3 was 5.5～10.5 and its optimum pH value for growth was 6.0～8.0. RY3 was G+, long-rod shape, monothetic and nonmotile, the colony was pale yellow with suborbicular-shape. Formate or H2+CO2 but not acetate was utilized by RY3 as sole C-source, and it was very sensitive to chloramphenicol. Besides, strain RY3 grew fastest at 55℃～65 and 0℃～2% NaCl. Characteristics of modality and physiology with sequence analysis of the 16s rDNA gene of strain RY3 preliminarily showed that it was Methanothermobacter thermautotrophicus. The experiments indicated that the time which began to produce methane with the highest velocity could be shortened two third by adding RY3 in one week, and the total methane production also was 1.8 times than before. Strain SH4 possessed wide scale of growing pH（5.5～9.5）and excellent ability of acclimatizing itself to acid-alkali. The methane production had no apparent difference among those cultivated in different initial pH（6.0～8.0）after three days and equaled to the maximum production basically. Cells of SH4 were G+, short-rod sharp, monothetic and nonmotile. The colony was pale yellow with suborbicular-shape. Formate or H2+CO2 but not acetate was utilized by SH4 as sole C-source, and it was very sensitive to chloramphenicol. Besides, it grew fastest at pH 7.0，55 ℃～65 and 0℃～2% NaCl concentration. The experiment indicated the time that began to produce methane could be shortening one third by adding SH4. And the total methane production also rose apparently. Characteristic of modality and physiology with sequence analysis of the 16S rDNA gene of strain SH4 demonstrated it was Methanobrevibacter arboriphilus. The activated sludge was utilized as fixture, mixed with culture medium and inocolum, that the solid compound inoculum could be produced by anaerobic fermentation. The compound inoculum could grow between pH 5.5～9.5, 15℃～65. It demonstrated the compound inoculum ha℃ve great ability of adapting to circumstance. In the experiment that making pig manure be substrate and taking the anaerobic sludge producing methane that cultured in long term in laboratory to be comparison, the concentration of methane in fermentation added compound inoculum almost equal to the comparison at 20℃, but the volume of gas production could be a little higher. The gas production everyday inoculated compound inoculum was 1.59 times to comparison. The time that the concentration of methane to maximum could be shortening by two third by adding compound inoculum, and the total gas production was 2.7 times to comprison while the total methane production was 2.8 times. If take the no inoculum be the comprasion, anaerobic fermentation added compound inoculum made the concentration of methane to 50% in 2 weeks but the comparison only to 4.3% at 20℃. The time that the concentration of methane to 50% by adding compound inoculum only need 1 week, but the comparison need 2 weeks at 50℃.

Shell model study of single-particle and collective structure in neutron-rich Cr isotopes

The structure of neutron-rich Cr isotopes is systematically investigated by using the spherical shell model. The calculations reproduce well the known energy levels for the even-even Cr52-62 and odd-mass Cr53-59 nuclei, and predict a lowering of excitation energies around neutron number N = 40. The calculated B(E2; 2(1)(+) -> 0(1)(+)) systematics shows a pronounced collectivity around N = 40; a similar characteristic behavior has been suggested for Zn and Ge isotopes. Causes for the sudden drop of the 9/2(1)(+) energy in Cr-59 and the appearance of very low 0(2)(+) states around N = 40 are discussed. We also predict a new band with strong collectivity built on the 0(2)(+) state in the N = 40 isotope Cr-64.

Properties and structure of N = Z nuclei within relativistic mean field theory

The axially deformed relativistic mean field theory with the force NLSH has been performed in the blocked BCS approximation to investigate the proper-ties and structure of N=Z nuclei from Z=20 to Z=48. Some ground state quantities such as binding energies, quadrupole deformations, one/two-nucleon separation energies, root-mean-squaxe (rms) radii of charge and neutron, and shell gaps have been calculated. The results suggest that large deformations can be found in medium-heavy nuclei with N=Z=38-42. The charge and neutron rms radii increase rapidly beyond the magic number N=Z=28 until Z=42 with increasing nucleon number, which is similar to isotope shift, yet beyond Z=42, they decrease dramatically as the structure changes greatly from Z=42 to Z=43. The evolution of shell gaps with proton number Z can be clearly observed. Besides the appearance of possible new shell closures, some conventional shell closures have been found to disappear in some region. In addition, we found that the Coulomb interaction is not strong enough to breakdown the shell structure of protons in the current region.

Matrix-bound phosphine: A new form of phosphorus found in sediment of Jiaozhou Bay

Matrix-bound phosphine (PH3), a new form of phosphorus, was found in sediment of Jiaozhou Bay in December 2001. Concentration and distribution of PH3 in different layers of sediment with different stations were analyzed. The results show that PH3 concentrations are various with different layers and different stations. PH3 concentrations in the bottom layer of sediment (20-30 cm) are usually higher than those in the surface layer (0-4 cm). The highest PH3 concentration in our investigation reaches 685 ng/kg (dry), which is much higher than those in terrestrial paddy soil, marsh and landfill that have been reported up to now. The correlation analysis indicates that there is no apparent correlation between the concentrations of PH3 and inorganic phosphorus in sediment. However, the correlation between the concentrations of phosphine and organic phosphorus in the bottom layer of sediment is remarkable (R-2=0.83). It is mainly considered that PH3 in sediment of Jiaozhou Bay is produced from the decomposition of organic phosphorus in the anaerobic condition, and so PH3 concentrations are related to organic phosphorus concentration and anaerobic environment in sediment. The discovery of PH3 in sediment will give people some new ideas on the mechanisms of phosphorus supplement and biogeochemical cycle in Jiaozhou Bay.

东营凹陷成藏组合体研究与勘探实践

With the development of petroleum exploration, subtle reservoir has become the main exploration object in Dongying Depression, which requires some new technologies and methods to further reveal the geological characteristics in step with the mature exploration stage. In this paper, on the references to the studies of petroleum system and multiple oil-gas accumulation belt with flexible maneuverability, and the application of systematic theory, the concept of reservoir assemblage is initially defined as "the association of active source rock(s) and hydrocarbon reservoir(s) that are genetically related, with the bridge of pathway system in an oil and gas bearing basin". Compared with the theories of petroleum system and multiple oil-gas accumulation belts, it emphasizes on the processes of petroleum migration and accumulation and the correlation among active source rock, trapped hydrocarbon and migration pathway, and has been confirmed to be more suitably applied to high maturely explored basin. In the first study of this paper, sequence stratigraphy and subtle analytical technology of source rock have been employed to find that two categories of source rock with their characteristic types of organic matter and substantial states occurred in Dongying Depression. The first category, consisting of the oil shales within the third-order sequences of lacustrine expanding system tracts in the upper interval of the fourth Member of Shahejie Formation and both in the middle and lower intervals of the third Member of Shahejie Formation, is featured with the highest abundance of total organic matter (TOC) and the strongest abilities of hydrocarbon generation and expulsion, which is classified into the standard of good hydrocarbon source rock. Exploration assessment confirmed that about 70-80% of hydrocarbon in Dongying Depression came from this set of source rock for which the low sedimentary rate and strong oxygen-free environment would play the key role during its generation. The second category, composed of organic matter of dark mudstone in high stand system tracts in the upper and middle intervals of the third Member of Shahejie Formation, has been characterized by low content of total organic matter which mostly dispersedly distributes, and formed in the pre-delta to delta front environments. In classification, it belongs to the ordinary standard of source rocks. In the second research part, through the studies of high frequency sequence stratigraphy, fault geometry and active history combining with geochemistry of fluid inclusion and nitrogen compound and simulation test of hydrocarbon migration and accumulation, the faults have been thought to be the principal conduits, and the sandy bodies and unconformities might played the complementary pathways for hydrocarbon migration and accumulation in Dongying Depression of the continental faulted basin. Therefore, the fault activities may mainly constrain on the development of hydrocarbon pathways in space and time. Even more, using homogenization temperatures of fluid inclusion in digenetic minerals, three critical moments for hydrocarbon accumulation have been determined as well in Dongying Depression, which happened during the late stage of Dongying Formation (Ed), the early stage of Guantao Formation (Nig) and the early stage of Minghuazhen Formation (Nim), respectively. Comparatively, the last stage is looked as the main forming-reservoir period, which has also been supported by the results of geochemical analysis and simulation experiments of hydrocarbon generation and expulsion. Clearly, the times of hydrocarbon migration and accumulation are consistent with those of the fault activities in Dongying Depression, which indicate that tectonic activities would control the forming-reservoir. A conceptual model of faulting-episodic expulsion coupled with episodic forming-reservoir has then been established in this study. In the third part of this paper, some focusing areas were selected for the fine descriptions of pathway distribution and forming-reservoir, which has given four types of reservoir assemblage in terms of the main pathway and its correlation with the reservoir and trap: (1) mainly consisted of sandy bodies; (2) mainly consisted of faults; (3) mainly consisted of unconformities; and (4) their complex with two or three types of pathways. This classified criteria has also been applied to access the risk of some prospected traps in Dongying Depression. Finally, through the application of reservoir assemblage integrated with pathway distribution to all the prospective targets in Dongying Depression, the new favorably hydrocarbon accumulated belts have been figured out, and more subtle reservoirs have also been found. For examples, during 2000 and 2002, in the mature exploration areas, such as Liangjialou and Shengtuo structural closures etc., newly proved reserves were 2274 * 104t, and forecasted oil reserves 5660-5860xl04t; and in the predicted favorable areas, newly additional controlled oil reserves was 3355xl04t. Besides those, many other favorable exploration areas need to be further appraised.

污泥处理经济评价和污泥堆肥中氧气监测与动态分析

With the continually increase both in the amount of wastewater disposal and in the treatment rate, more and more sewage sludge has been produced. An economic estimate was taken on the different sewage sludge disposal and treatment technologies, and led to the conclusion that compost is an effective way to make sewage sludge harmless, stable and resourceable. Normally, there are several ways to treat sewage sludge, such as landfill, compost, incineration and so on. These technologies will cost 300-1000 Y per ton of sludge. Among those ways, landfill is the cheapest one and operates easily, however, it just postpones the pollution instead of eventually eliminating the pollution; The amount of the sludge will reduce dramatically after incineration, while incineration will take a very high investment in the beginning, at the same time, it's very hard to maintain running; Sewage sludge will be resourceful after composting treantment, thus makes up the treatment cost, makes composting is the most economical way. Compost production is safe when correctly used, compost is a important way to treat sewage sludge. Oxygen is an important control factor in aerobic composting that has great effects on temperature and microorganisms. The gas gathering and transfering system of an online oxygen monitoring system for composting were bettermented to prolong the monitoring system's running period. The oxygen concentration changes in various aerobic composting stage were studied, and conclusions came to that oxygen concentration changes much faster in the oxygen concentration increasing stage than that in the declining stage; the better the aerobic condition is, the sooner the monitoring system starts to work. The minimal oxygen concentration during a ventilation cycle often falls at the beginning, then ascends in the composting period; at the same time, oxygen concentration changes fast in the early composting stage(temperature increasing stage), much slower in the middle stage(continouns thermophilic stage),and seldom changes in the late composting stage(temperature declining stage). With the help of the oxygen realtime-online monitoring system, oxygen concentrations was measured. During the composting period, water contents was analyzed after sampled. It's found that water contents (WC) and Oxygen concentration can both influence the composting process, and the control rule varies in the various composting stages. Essentially, the rule that water and oxygen control the composting process comes from water counterchecks the oxygen transferring to the composting substrate. The most influential factor to the WC and to the oxygen is the components in the composting pile. In the temperature increasing stage, seldom microorganisms exist in the composting pile with low activity, thus oxygen can meet with microorganisms' need, and WC is the dominant factor. In the high temperature (continouns thermophilic) stage, composting process is controlled by WC and oxygen, essentially by WC, at the same time, their influence somehow is not remarkable. In the temperature declining stage, WC and oxygen influence the composting process little. It's also found that the composting process will differ even if under the same components, thus to equably mix the components can avoid WC focusing in some place and let the composting pile to be aerobic. In one sentence, aerobic state is the most important factor in the composting process, suitable bulking material will be useful to the composting control.

Representations and evolutionary operators for the scheduling of pump operations in water distribution networks.

Reducing the energy consumption of water distribution networks has never had more significance. The greatest energy savings can be obtained by carefully scheduling the operations of pumps. Schedules can be defined either implicitly, in terms of other elements of the network such as tank levels, or explicitly by specifying the time during which each pump is on/off. The traditional representation of explicit schedules is a string of binary values with each bit representing pump on/off status during a particular time interval. In this paper, we formally define and analyze two new explicit representations based on time-controlled triggers, where the maximum number of pump switches is established beforehand and the schedule may contain less switches than the maximum. In these representations, a pump schedule is divided into a series of integers with each integer representing the number of hours for which a pump is active/inactive. This reduces the number of potential schedules compared to the binary representation, and allows the algorithm to operate on the feasible region of the search space. We propose evolutionary operators for these two new representations. The new representations and their corresponding operations are compared with the two most-used representations in pump scheduling, namely, binary representation and level-controlled triggers. A detailed statistical analysis of the results indicates which parameters have the greatest effect on the performance of evolutionary algorithms. The empirical results show that an evolutionary algorithm using the proposed representations improves over the results obtained by a recent state-of-the-art Hybrid Genetic Algorithm for pump scheduling using level-controlled triggers.

A toolkit approach to solar radiation modelling.

Considerable effort is required to implement solar radiation models in software. Many existing implementations have efficiency as their main priority rather than re-usability, and this can adversely affect their further development since the relationships between the software and physical quantities may be obscured. The Solar Toolkit is an attempt to overcome such barriers by exploiting the current abundance of computing resource, and the availability of user-oriented tools such as Microsoft Excel®. The Solar Toolkit takes the form of a set of functions written in Visual Basic for Applications® (VBA) made available under the Academic Free Licence. Transparency is the overriding priority throughout the implementation so that the Toolkit can provide a platform for further modelling initiatives.

Solar photovoltaic system applications: a guidebook for off-grid electrification.

Presenting a complete guide for the planning, design and implementation of solar PV systems for off-grid applications, this book features analysis based on the authors’ own laboratory testing as well as their in the field experiences. Incorporating the latest developments in smart-digital and control technologies into the design criteria of the PV system, this book will also focus on how to integrate newer smart design approaches and techniques for improving the efficiency, reliability and flexibility of the entire system. The design and implementation of India’s first-of its-kind Smart Mini-Grid system (SMG) at TERI premises, which involves the integration of multiple renewable energy resources (including solar PV) through smart controllers for managing the load intelligently and effectively is presented as a key case study. Maximizing reader insights into the performance of different components of solar PV systems under different operating conditions, the book will be of interest to graduate students, researchers, PV designers, planners, and practitioners working in the area of solar PV design, implementation and assessment.

A concise review on some frequently used solid waste management technologies and their effects into the environment and human health

uma revisão sobre alguns estudos epidemiológicos melhorará a compreensão quanto aos efeitos potenciais na saúde da gestão de resíduos e permitirá obter informação importante em termos de trabalho futuro. Alguns estudos mostraram associações significativas entre diversos métodos de gestão de resíduos e impactos potenciais na saúde humana. noutros estudos as associações foram consideradas inconsistentes ou susceptíveis de conduzir a equívocos, sendo necessários mais estudos epidemiológicos para averiguar as consequências para a saúde humana e para determinar os seus efeitos toxicológicos directos, assegurando assim que a gestão de resíduos representa um risco mínimo para a saúde. os estudos epidemiológicos devem ser analisados com uma mente aberta, tomando em consideração factores como o estatuto social e a migração das populações. A review of a few epidemiologic studies will improve the understanding of the potential health effects of waste management and will provide important information regarding future work. several studies showed significant relationships between several methods of waste management and potential impacts on human health. in other studies associations were found to be inconsistent or equivocal and more specific epidemiological studies must be performed to assess consequences to human health and to determine their direct toxicological effects, thus ensuring that waste management pose minimum risk to health.

Efficient Support for Common Relations in Lightweight Formal Reasoning Systems

In work that involves mathematical rigor, there are numerous benefits to adopting a representation of models and arguments that can be supplied to a formal reasoning or verification system: reusability, automatic evaluation of examples, and verification of consistency and correctness. However, accessibility has not been a priority in the design of formal verification tools that can provide these benefits. In earlier work [Lap09a], we attempt to address this broad problem by proposing several specific design criteria organized around the notion of a natural context: the sphere of awareness a working human user maintains of the relevant constructs, arguments, experiences, and background materials necessary to accomplish the task at hand. This work expands one aspect of the earlier work by considering more extensively an essential capability for any formal reasoning system whose design is oriented around simulating the natural context: native support for a collection of mathematical relations that deal with common constructs in arithmetic and set theory. We provide a formal definition for a context of relations that can be used to both validate and assist formal reasoning activities. We provide a proof that any algorithm that implements this formal structure faithfully will necessary converge. Finally, we consider the efficiency of an implementation of this formal structure that leverages modular implementations of well-known data structures: balanced search trees and transitive closures of hypergraphs.

Human dimensions of bycatch reduction technology: Current assumptions and directions for future research

Bycatch reduction technology (BRT) modifies fishing gear to increase selectivity and avoid capture of non-target species, or to facilitate their non-lethal release. As a solution to fisheries-related mortality of non-target species, BRT is an attractive option; effectively implemented, BRT presents a technical 'fix' that can reduce pressure for politically contentious and economically detrimental interventions, such as fisheries closures. While a number of factors might contribute to effective implementation, our review of BRT literature finds that research has focused on technical design and experimental performance of individual technologies. In contrast, and with a few notable exceptions, research on the human and institutional context of BRT, and more specifically on how fishers respond to BRT, is limited. This is not to say that fisher attitudes are ignored or overlooked, but that incentives for fisher uptake of BRT are usually assumed rather than assessed or demonstrated. Three assumptions about fisher incentives dominate: (1) economic incentives will generate acceptance of BRT; (2) enforcement will generate compliance with BRT; and (3) 'participation' by fishers will increase acceptance and compliance, and overall support for BRT. In this paper, we explore evidence for and against these assumptions and situate our analysis in the wider social science literature on fisheries. Our goal is to highlight the need and suggest focal areas for further research. © Inter-Research 2008.

Environmental and Human Pathogenic Microorganisms

As the study of interactions between pathogenic microorganisms and their environment is part of microbial ecology, this chapter reviews the different types of human pathogens found in the environment, the different types of fecal indicators used in water quality monitoring, the biotic and abiotic factors affecting the survival and the infectivity of pathogenic microorganisms during their transportation in the environment, and the methods presently available to detect rare microorganisms in environmental samples. This chapter exclusively focuses on human pathogens.