Electrochemical corrosion behavior of Mg-5Al-0.4Mn-xNd in NaCl solution

The electrochemical corrosion behavior of Mg-5Al-0.4Mn-xNd (x = 0, 1, 2 and 4 wt.%) alloys in 3.5% NaCl solution was investigated. The corrosion behavior of the alloys was assessed by open circuit potential measure, potentiodynamic polarization, and electrochemical impedance spectroscopy. The electrochemical results show the intermetallic precipitates with Nd behave as less noble cathodes in micro-galvanic corrosion and suppress the cathodic process. During corrosion, Al2O3 and Nd2O3, in proper ratio, is incorporated into the corrosion film, and enhances the corrosion resistance.

Microstructures and mechanical properties of extruded Mg-8Gd-0.4Zr alloys containing Zn

Microstructures and mechanical properties of the Mg-8Gd-xZn-0.4Zr (x = 0, 1 and 3 wt.%) alloys in the as-cast, as-extruded and extruded-T5 conditions, have been investigated. The peak-aged Mg-8Gd-1Zn-0.4Zr alloy during isothermal ageing at 423 K acquires highest mechanical properties, with the highest ultimate tensile strength and yield tensile strength of 314 and 217 MPa, respectively. Addition of Zn has obvious effect on age hardening responses, especially for 1 wt.% Zn addition. It is due to a uniform distribution of beta' phase which can impede the movement of dislocations. However, addition of 3 wt.% Zn to the Mg-8Gd-0.4Zr alloy leads to a precipitation of Mg3Zn3Gd2 phase (W-phase). This phase is incoherent with interface of the matrix and becomes cores of the fracture in tensile test at room or elevated temperature.

Thermal stability, crystallization, structure and morphology of syndiotactic 1,2-polybutadiene/organoclay nanocomposite

Syndiotactic 1,2-polybutadiene/organoclay nanocomposites were prepared and characterized by thermogravimetry analysis (TGA), X-ray diffraction (XRD), polarized optical microscopy (POM), and differential scanning calorimetry (DSC), respectively. The XRD shows that exfoliated nanocomposites are formed dominantly at lower clay concentrations (less than 2%), at higher clay contents intercalated nanocomposites dominate. At the same time, the XRD indicates that the crystal structures of sPB formed in the sPB/organoclay nanocomposites do not vary, only the relative intensity of the peaks corresponding to (0 1 0) and (2 0 0)/(1 1 0) crystal planes, respectively, varies. The DSC and POM indicate that organoclay layers can improve cooling crystallization temperature, crystallization rate and reducing the spherulite sizes of sPB. TGA shows that under argon flow the nanocomposites exhibit slight decrease of thermal stability, while under oxygen flow the resistance of oxidation and thermal stability of sPB/organoclay nanocomposites were significantly improved relative to pristine sPB. The primary and secondary crystallization for pristine sPB and sPB/organoclay (2%) nanocomposites were analyzed and compared based on different approaches.

Luminescence properties of Y0.9-xGdxEu0.1Al3(BO3)(4) (0 <= x <= 0.9) phosphors prepared by spray pyrolysis process

Starting from metal nitrate aqueous solutions and H3BO3, Y0.9-xGdxEu0.1Al3(BO3)(4) (0 <= x <= 0.9) phosphors were synthesized by spray pyrolysis followed by annealing at high temperature. The obtained phosphor particles have spherical morphology with size in the range 0.5-2 mu m. Independent of the x values in Y0.9-xGdxEu0.1Al3(BO3)(4) (0 <= x <= 0.9) phosphors, the Eu3+ ion shows its characteristic D-5(0), (1)-F-7(J) (J = 0, 1, 2, 3, 4) transitions with D-5(0)-F-7(2) red emission (612 nm) as the most prominent group. The photoluminescence intensity of phosphors increases with the increase of x value in Y0.9-xGdxEu0.1Al3(BO3)(4) (0 <= x <= 0.9) due to an energy migration process like Gd3+-(Gd3+)(n)-Eu3+ that occurred in the host materials.

Electrosynthesis and characterization of 1,2-dibenzyl C-60: A revisit

A reinvestigation of the reaction between C-60(2-) and benzyl bromide in benzonitrile containing 0.1 M tetra-n-butylammonium perchlorate (TBAP) has shown that there are more reaction products than previously reported. Use of a silica rather than a "Buckyclutcher I" column for HPLC purification led to isolation of two previously unattained products in the reaction mixture, one of which was identified as 1,2-(PhCH2)(2)C-60 by UV-vis and NMR. The earlier incorrectly assigned 1,2-(PhCH2)(2)C-60 was identified as the methanofullerene C61HPh by X-ray single-crystal diffraction. The electrochemistry of genuine 1,2-(PhCH2)(2)C-60 shows that its first reduction potential in PhCN containing 0.1 M TBAP is cathodically shifted by 100 mV with respect to E-1/2 for reduction of 1,4-(PhCH2)(2)C-60, indicating that the addition pattern significantly affects the electrochemistry of derivatized C-60. Visible and near-IR spectra of the monoanion and dianion of 1,2-(PhCH2)(2)C-60 are also reported.

聚对苯二甲酸1,3-丙二醇酯溶液浇铸薄膜形态结构

聚对苯二甲酸 1 ,3-丙二醇酯 ( PTT)是典型的半结晶聚合物 ,从熔体结晶形成球晶 ,在某一结晶温度范围内 ,在球晶中可观察到环带结构[1～ 4 ] .一般认为 ,环带球晶的形成归因于片晶沿球晶径向的周期性扭曲[1,2 ] .本文研究了 PTT溶液浇铸薄膜在溶剂挥发过程中等温结晶的形态结构 .1　实验部分　　 PTT样品为美国壳牌化学公司产品 ,熔点为 2 2 8℃ .将 PTT粒料于 1 1 0℃溶解在苯酚和1 ,1 ,2 ,2 -四氯乙烷 (质量比为 60∶ 40 )的混合溶剂中 ,配成质量分数为 0 .2 %～ 2 %的溶液 ,滴少许溶液在加热的云母片上 ,在预先设定的结晶温度 ( 90～ 2 0 0℃ )下等温结晶 ,然后将 PTT薄膜快速冷却至室温 .用 Leica DMLP偏光显微镜 ( PL M)和 SPA- HV30 0原子力显微镜 ( AFM)进行形态表征 .2　结果与讨论　　图 1为 PTT溶液浇铸薄膜在不同温度下等温结晶后的 PLM图 ,可以清楚地看到 Maltese十字消光现象 .PTT溶液浇铸薄膜在 90～ 1 30℃的结晶温度范围内 ,形成环带球晶 ;当结晶温度为 1 40℃...

Green electroluminescent polyfluorenes containing 1,8-naphthalimide moieties as color tuner

A series of copolymers (CNPFs) containing low-band-gap 1,8-naphthalimide moieties as color tuner was prepared by a Yamamoto coupling reaction of 2,7-dibromo-9,9-dioctylfluorene (DBF) and different amount of 4-(3,6-dibromocarbazol-9-yl)-N-(4'-tert-butyl-phenyl)-1,8-naphthalimide (Br-CN) (0.05-1 mol% feed ratio). The light emitting properties of the resulting copolymers showed a heavy dependence on the feed ratio. In photoluminescence (PL) studies, an efficient color tuning through the Forster energy transfer mechanism was revealed from blue to green as the increase of Br-CN content, while in electroluminescence (EL) studies, the color tuning was found to go through a charge trapping mechanism. It was found that by introduction of a very small amount of Br-CN (0.1-0.5 mol%) into polyfluorene, the emission color can be tuned from blue to pure green with Commission International de l'Echairage (CIE) coordinates being (0.21, 0.42) and (0.21, 0.48). A green emitting EL single-layer device based on CNPF containing 0.1 mol% of Br-CN showed good performances with a low turn-on voltage of 4.2 V, a brightness of 9104 cd/m(2), the maximum luminous efficiency of 2.74 cd/A and the maximum power efficiency of 1.51 lm/W.

Sol-gel derived carbon ceramic electrode bulk-modified with tris(1,10-phenanthroline-5,6-dione)iron(II) hexafluorophosphate and its use as an amperometric iodate sensor

A surface-renewable tris (1,10-phenanthroline-5, 6-dione) iron (II) hexafluorophosphate (FePD) modified carbon ceramic electrode was constructed by dispersing FePD and graphite powder in methyltrimethoxysilane (MTMOS) based gels. The FePD-modified electrode presented pH dependent voltammetric behavior, and its peak currents were diffusion-controlled in 0.1 mol/L Na2SO4 + H2SO4 solution (pH = 0. 4). In the, presence of iodate, clear electrocatalytic reduction waves were observed and thus the chemically modified electrode was used as an amperometric sensor for iodate in common salt. The linear range, sensitivity, detection limit and response time of the iodate sensor were 5 x 10(-6)-1 x 10(-2) mol/L, 7.448 muA.L/mmol, 1.2 x 10(-6) mol/L and 5 s, respectively. A distinct advantage of this sensor is its good reproducibility of surface-renewal by simple mechanical polishing.

H-1 NMR analysis for metabolites in serum and urine from rats administrated chronically with La(NO3)(3)

H-1 NMR spectroscopy has been used to assess long-term toxicological effects of a rare earth. Male Wistar rats were administrated orally with La(NO3)(3) at doses of 0.1, 0.2, 2.0, 10, and 20 mg/kg body wt, resp., for 3-6 months. Urine was collected at 1, 2, and 3 months and serum samples were taken after 6 months. Numerous low-M-r metabolites in rats serum and rats urine, including creatinine, citrate, glucose, ketone bodies, trimethylamine N-oxide (TMAO), and various amino acids, were identified on 400- and 500-MHz H-1 NMR spectra. La3+-induced renal and liver damage is characterized by an increase in the amounts of the excreted ketone bodies, amino acids, lactate, ethanol, succinate, TMAO, dimethylamine, and taurine and a decrease in citrate, glucose, urea, and allantoin. Information on the molecular basis of the long-term toxicity of La(NO3)(3) was derived from the abnormal patterns of metabolite excretions. An assay of some biochemical indexes and analysis of some enzymes in plasma supported NMR results.

Synthesis and crystal structure of triphenyltin-2-(1,2-ethylenedithio) methylene-3-oxo-5-aryl-4-pentenicate

Nine triphenyltin - 2 - (1,2 - ethylenedithio) methylene - 3 - oxo - 5 - aryl - 4 - pentenicates were synthesized. The crystal structure of the title compound 3b (C33H28O3S2Sn) was determined by X - ray diffraction analysis. The crystal belongs to triclinic system, space group P(1)overbar with a = 0.9074 (2) nm, b = 1.6809(3)nm, c = 2.1834(4)nm, alpha =77.57(3)degrees, beta = 88.04(3)degrees, gamma = 89.47(3)degrees, V = 3.2503nm(3), Z = 2, R = 0.0592. In crystal of 3b, there exist intramolecular 0-Sn coordination bonds, with carboxylate group acting as a bidentate ligand: Sn(1)-0(1) = 0.2086(5) and Sn(1)-0(2) = 0.2594nm, having a deformed trigonal bipyramidal geometry.

Self-organization of interlaced network lamellar crystals of trans-1,4-polybutadiene (TPBD) on an amorphous surface

A novel morphology of TPBD crystals consisting of a three-dimensional interlaced network was obtained by casting the self-seeded 0.1% benzene solution onto carbon-boated mica. Both the transmission electron microscopy (TEM) and electron diffraction (ED) analyses showed that the network was composed of well-developed lamellae. It is imagined this interesting morphology is the results of asymmetrical growth of the original TPBD lamellae on the amorphous interface, and that their preferred orientation changed when they encountered each other.

应用玻璃微米/纳米管和循环伏安法研究邻菲咯啉加速质子在水/1,2-二氯乙烷界面的转移过程

利用循环伏安法研究了玻璃微米 /纳米管支持的水 / 1 ,2 -二氯乙烷 ( DCE)界面上邻菲咯啉加速质子的转移过程 .将装有水溶液的微米 /纳米管插入到 DCE溶液中 ,可以形成微米 /纳米级 -液 /液界面 ,在选定的实验条件下 ,其作用类似于微米 /纳米电极 .用微米管考察了此加速转移过程的半波电位与 p H值 ( 1 .1～7.5 )的关系 ,利用 Matsuda等提出的理论公式计算了邻菲咯啉与质子在有机相和水相中的络合常数比 .并用纳米管计算得到邻菲咯啉加速质子在水 / DCE界面转移过程中的标准速率常数 ( k0 )和转移系数 (α)分别为( 0 .1 83± 0 .0 5 4 ) cm/ s和 0 .70± 0 .0

Calculation of chemical bond parameters in La1-xCaxCrO3 (0.0 <= x <= 0.3)

The chemical bond parameters, that is, bond covalency, bond susceptibility, and macroscopic linear susceptibility of La1-xCaxCrO3 (x = 0.0, 0.1, 0.2, 0.3) has been calculated using a semiempirical method. This method is the generalization of the dielectric description theory proposed by Phillips, Van Vechten, Levine, and Tanaka (PVLT). In the calculation of bond valence, two schemes were adopted. One is the bond valence sums (BVS) scheme, and the other is the equal-valence scheme. Both schemes suggest that for the title compounds bond covalency and bond susceptibility are mainly influenced by bond valence and are insensitive to the Ca doping level or structural change. Larger bond valences usually result in higher bond covalency and bond susceptibility. The macroscopic linear susceptibility increases (only slightly for BVS scheme) with the increasing Ca doping level. (C) 1999 John Wiley & Sons, Inc.

Laser light-scattering study of novel thermoplastics .1. Phenolphthalein poly(aryl ether ketone)

Five different molecular weight phenolphthalein poly(aryl ether ketone) (PEK-C) fractions in CHCl3 were studied by static and dynamic laser light scattering(LLS). The dynamic LLS revealed that the PEK-C samples contain some large polymer clusters. These large clusters can be removed by filtering the solution with a 0.1-mu m filter. We found that the persistence length of PEK-C in CHCl3 at 25 degrees C is similar to 2 nm and the Flory characteristic ratio, C-infinity is similar to 25. Our results showed that [R(g)(2)](1/2)(z) = (3.50+/-0.20) x 10(-2)M(w)(0.54+/-0.01) and [D] = (2.37+/-0.05) x 10(-4)M(w)(-0.55+/-0.01), with [R(g)(2)](1/2)(z), M(w), and [D] being the z-average radius of gyration, the weight-average molecular weight, and the z-average translational diffusion coefficient, respectively. A combination of static and dynamic LLS results enabled us to determine D = (2.20+/-0.10) x 10(-4)M(-0.555+/-0.015), where D and M correspond to monodisperse species. Using this calibration between D and M,we have determined molecular weight distributions of five PEK-C fractions from their corresponding translational diffusion coefficient distribution.

A STUDY OF CATALYTIC PROPERTIES OF PEROVSKITE-TYPE OXIDES LAMNYCO1-YO3 .1. THE RELATIONSHIP BETWEEN THE TYPE OF OXYGEN SPECIES AND THE CATALYTIC PROPERTY IN AMMONIA OXIDATION

The type of oxygen species in perovskite-type oxides LaMnyCo1-yO3 (y = 0.0, 0.1, 0.3, 0.5, 0.7, 0.9, 1.0) has been studied by means of XRD, XPS and TPD. The catalytic activity in ammonia oxidation was also investigated. It was found that there were three desorption peaks in TPD curve corresponding to three types of oxygen species (alpha, beta, beta'). The desorption temperatures were 293 K less-than-or-equal-to T(alpha) less-than-or-equal-to 773 K, 773 K less-than-or-equal-to T(beta) less-than-or-equal-to K and T(beta') greater-than-or-equal-to 1073 K respectively. The relationship among the composition, structure and the catalytic property of.the catalyst was correlated and could be explainned with a model based on solid defect reaction and the interaction between Co and Mn ions. The adsorption strength and quantity of a oxygen are proportional to the catalytic activity. The, result indicates that the synergetic effect between B-site ions seems to the benefit of the ammonis oxidation reaction.