Evaluation of the main MPPT techniques for photovoltaic applications

This paper presents evaluations among the most usual maximum power point tracking (MPPT) techniques, doing meaningful comparisons with respect to the amount of energy extracted from the photovoltaic (PV) panel [tracking factor (TF)] in relation to the available power, PV voltage ripple, dynamic response, and use of sensors. Using MatLab/Simulink and dSPACE platforms, a digitally controlled boost dc-dc converter was implemented and connected to an Agilent Solar Array E4350B simulator in order to verify the analytical procedures. The main experimental results are presented for conventional MPPT algorithms and improved MPPT algorithms named IC based on proportional-integral (PI) and perturb and observe based on PI. Moreover, the dynamic response and the TF are also evaluated using a user-friendly interface, which is capable of online program power profiles and computes the TF. Finally, a typical daily insulation is used in order to verify the experimental results for the main PV MPPT methods. © 2012 IEEE.

The need of subsidy for the implementation of photovoltaic solar energy as supporting of decentralized electrical power generation in Brazil

The growing demand for electrical power and the limited capital invested to provide this power is forcing countries like Brazil to search for new alternatives for electrical power generation. The purpose of this paper is to present a technical and economic study on a 15 kW solar plant installed in an isolated community, highlighting the importance of the need for financial subsidy from the government. It evaluates the importance of parameters such as the annual interest rate, specific investment, the marginal cost of expanding the electrical power supply and the government subsidy on amortization time of capital invested. © 2012 Elsevier Ltd All rights reserved.

Morphological modifications and surface amorphization in ZnO sonochemically treated nanoparticles

Application of nanoscale materials in photovoltaic and photocatalysis devices and photosensors are dramatically affected by surface morphology of nanoparticles, which plays a fundamental role in the understanding of the physical and chemical properties of nanoscale materials. Zinc oxide nanoparticles with an average size of 20 nm were obtained by the use of a sonochemical technique. X-ray diffraction (XRD) associated to Rietveld refinements and transmission electron microscopy (TEM) were used to study structural and morphological characteristics of the samples. An amorphous shell approximately 10 nm thick was observed in the ultrasonically treated sample, and a large reduction in particle size and changes in the lattice parameters were also observed. © 2012 Elsevier B.V. All rights reserved.

A novel LTCC electrochemical cell construction and characterization: A detection compartment for portable devices

In this work we described for the first time the construction of a 25 μL electrochemical cell from low temperature co-fired ceramic (LTCC) material and carbon screen-printed electrode applicable in portable devices. Firstly, a carbon screen-printed electrode was prepared and characterized by cyclic voltammetry and scanning electron microscopy. Afterwards carbon polymeric film and metal pastes were dropped into the LTCC cell cavities in order to determine the device electrodes, and this arrangement was also electrochemically characterized. The great advantage of this promising device is the simple construction method and its widespread applicability in reusable portable devices. © 2013 The Royal Society of Chemistry.

Determination of in situ speciation of manganese in treated acid mine drainage water by using multiple diffusive gradients in thin films devices

Acid mine drainage (AMD) is a serious environmental problem that creates acidic solution with high Mn concentrations. The speciation of residual Mn from AMD after an active treatment involving the addition of a neutralizing agent can reliably evaluate the treatment efficiency and provide knowledge of the Mn species being inputted into the environment. The aim of this study was to evaluate the in situ lability and speciation of Mn using the diffusive gradients in thin films (DGT) technique with treated drainage water from a uranium mine (TAMD). DGT devices with different binding phases (Chelex-100 and P81 and DE81membranes) were used to perform the in situ speciation of Mn. A comparison of the results from deploying DGT in the laboratory and in situ shows that the speciation of Mn in TAMD should be performed in situ. Linear deployment curves (from in situ experiments) indicate that the DGT device containing the Chelex-100 binding phase can be used to evaluate Mn lability in TAMD. The labile Mn fraction (from in situ measurements) obtained using the device containing the Chelex-100 resin ranged from 63 to 81% of the total Mn concentration and, when compared to the speciation obtained using the CHEAQS software, indicated that this device was capable of uptaking the free Mn2+ and a portion of the MnSO4(aq). The values obtained using the DGT technique were compared to those from on site solid phase extraction, and a good agreement was found between the results. The amount of negative Mn species sampled by DE81 device was insignificant (<1.5%) for all of the sites. Sites containing a relatively small amount of Ca (<40mgL-1) and measured using devices containing the P81 membrane agreed with the concentration predicted by the CHEAQS software for positive Mn species (Mn2+ and Mn(OH)+). Nevertheless, the speciation obtained using the CHEAQS software indicated that the concentrations of positive Mn species were underestimated for sites with relatively high Ca concentrations (>150mgL-1), which take place due to the saturation of binding sites in the P81 membrane. © 2013 Elsevier B.V.

Florida's two devices for water management

Includes bibliography

Estudo das propriedades de fotogeração e transporte de portadores de cargas em dispositivos optoeletrônicos orgânicos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo da viabilidade energética de amortecedores regenerativos por indução com ênfase nos carros elétricos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Desenvolvimento de framework para análise e simulação dinâmica de sistemas elétricos de potência

Esta tese apresenta uma metodologia flexível orientada a objetos (OO) para a aplicação no projeto e implementação de sistemas de software utilizados na realização de estudos dinâmicos de sistemas elétricos de grande porte. A metodologia OO proposta objetiva tornar mais simples o desenvolvimento, a atualização e a manutenção de complexos sistemas de software para estudos de transitórios eletromecânicos em sistemas elétricos de potência. Os requisitos de usuário são mapeados para um conjunto de classes básicas, as quais são usadas para efetuar a modelagem de dispositivos dinâmicos tais como geradores elétricos. Para avaliação da metodologia foram realizados dois estudos de casos. No primeiro estudo caso o Framework foi aplicado na simulação das unidades geradoras da Usina Hidrelétrica de Tucuruí. Os resultados da simulação foram comparados com medições obtidos em ensaios no campo e mostrou a boa performance do Framework na reprodução dos fenômenos eletromecânicos desta usina de grande porte. No segundo estudo de caso, por outro lado, o Framework foi aplicado na modelagem de um sistema de geração fotovoltaico (PV) com seu sistema de Rastreamento da Potência Máxima (MPPT). O controle MPPT foi implementado usando técnicas digitais. Os resultados das simulações demonstram a performance do Framework na modelagem do sistema de controle de corrente, assim como no controle MPPT, dos sistemas de geração PV.

Desenvolvimento de monitoramento remoto em um sistema híbrido isolado de pequeno porte

Este trabalho visa avaliar as dificuldades e utilidades do monitoramento remoto de um sistema para o atendimento de cargas isoladas da rede elétrica, envolvendo sistemas reais em operação que podem ajudar a identificar os principais fatores que influenciam na vida útil desses dispositivos, tornando possível propor estratégias e tecnologias que melhorem a confiabilidade do sistema, possibilitem uma configuração mais adequada e reduzam os custos globais do sistema ao longo de sua vida útil. Para isso foi incorporado um sistema de monitoramento remoto via LabVIEW a um sistema híbrido isolado insta-lado em flutuante localizada as margens do lago da cidade de Tefé-AM. O sistema de geração foi composto inicialmente por um gerador fotovoltaico (FV) com potência de 2,08 kWp, dois subgeradores 1,04 kWp cada, e depois ampliado para 2,6 Wp mais 350 Wp de geração eólica. Além disso, um banco de acumuladores eletroquímicos com tensão nominal de 24 V e composto por 20 baterias de 150 Ah cada, Dois controladores de carga 24 V / 40 A e um inversor de onda senoidal de 1.500 VA. Resultados de operacionais apresentados neste trabalho ajudam a entender melhor o funcionamento desses sistemas e avaliar as barreiras encontradas no monitoramento remoto dessas unidades. Esse expe-rimento foi realizado em parceria do laboratório do Grupo de Estudos e Desenvolvimento de Alternativas Energéticas na Universidade Federal do Pará com o Núcleo de Inovação tecnológica do Instituto de Desenvolvimento Sustentável Mamirauá.

Desenvolvimento e otimização de materiais nanocristalinos para células solares sensibilizadas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Desenvolvimento de um sistema para monitoramento remoto em centrais de microgeração fotovoltaica

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Micro-inverter for integrated grid-tie photovoltaic module using resonant controller

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Phenomenological Interpretation of Impedance/Capacitance Measurements on Organic Electronic Devices Under Illumination

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)