Stable isotope (C, O, S) systematics of the mercury mineralization at Idrija, Slovenia: constraints on fluid source and alteration processes

The world-class Idrija mercury deposit (western Slovenia) is hosted by highly deformed Permocarboniferous to Middle Triassic sedimentary rocks within a complex tectonic structure at the transition between the External Dinarides and the Southern Alps. Concordant and discordant mineralization formed concomitant with Middle Triassic bimodal volcanism in an aborted rift. A multiple isotopic (C, O, S) investigation of host rocks and ore minerals was performed to put constraints on the source and composition of the fluid, and the hydrothermal alteration. The distributions of the delta(13)C and delta(18)O values of host and gangue carbonates are indicative of a fracture-controlled hydrothermal system, with locally high fluid-rock ratios. Quantitative modeling of the delta(13)C and delta(18)O covariation for host carbonates during temperature dependent fluid-rock interaction, and concomitant precipitation of void-filling dolomites points to a slightly acidic hydrothermal fluid (delta(13)Capproximate to-4parts per thousand and delta(18)Oapproximate to+10parts per thousand), which most likely evolved during isotopic exchange with carbonates under low fluid/rock ratios. The delta(34)S values of hydrothermal and sedimentary sulfur minerals were used to re-evaluate the previously proposed magmatic and evaporitic sulfur sources for the mineralization, and to assess the importance of other possible sulfur sources such as the contemporaneous seawater sulfate, sedimentary pyrite, and organic sulfur compounds. The delta(34)S values of the sulfides show a large variation at deposit down to hand-specimen scale. They range for cinnabar and pyrite from -19.1 to +22.8parts per thousand, and from -22.4 to +59.6parts per thousand, respectively, suggesting mixing of sulfur from different sources. The peak of delta(34)S values of cinnabar and pyrite close to 0parts per thousand is compatible with ore sulfur derived dominantly from a magmatic fluid and/or from hydrothermal leaching of basement rocks. The similar stratigraphic trends of the delta(34)S values of both cinnabar and pyrite suggest a minor contribution of sedimentary sulfur (pyrite and organic sulfur) to the ore formation. Some of the positive delta(34)S values are probably derived from thermochemical reduction of evaporitic and contemporaneous seawater sulfates.

Apparent stable-isotope heterogeneities in gangue carbonates of the Mississippi Valley-type Zn-Pb deposits of San-Vicente, Central Peru

The aim of the present communication is to emphasize that some variations of the measured delta(13)C and delta(18)O values are apparent, and due to analytical interferences caused by the presence of sulfur and organosulfur compounds in the analyzed carbonates. This is particularly relevant for isotopic studies on carbonate-hosted mineral deposits, where the nearly ubiquitous association of the host carbonates with organic matter and sulfides can certainly affect the metallogenetic interpretations. In this work two methods were used to overcome the disturbing effects of sulfides and organic matter: (1) sample pretreatment following the method proposed by Charef and Sheppard (1984), combining the oxidation of organic matter with sodium hypochlorite and trapping of the sulfur species with silver phosphate; and (2) laser-based microprobe extraction. Apparent isotopic variations in sparry dolomite from a single hand sample of zebra ore from the MVT Zn-Pb deposit, San Vicente, central Peru, are as large as 6 parts per thousand delta(13)C and 4 parts per thousand delta(18)O. These variations are reduced to several tenths of a per mil when the samples are pretreated. A careful examination of the effects of treatment with NaOCl and/or Ag3PO4 in relation to the concentration of sulfide inclusions indicates that the main disturbing effects for delta(13)C values are the presence of sulfur species and organic matter, whereas the delta(18)O values are mainly affected by the presence of sulfides. Fine- and medium-grained replacement carbonates from MVT and other sediment-hosted base metal deposits are potentially the most affected during isotope analysis, due to the common presence of organic matter and sulfides. Using in situ laser microprobe techniques, it is possible to determine isotopic variations at a sub-millimeter scale. Our results show that laser extraction analysis allows a more precise sampling of the carbonate minerals, and minimizes contamination of the sample with sulfides and to some extent with intergrown organic matter. However, there is an isotopic shift associated with the laser extraction technique, of the order of 0.5-1 parts per thousand for delta(13)C and delta(18)O values.

Feed intake and growth performance of goats supplemented with soy waste

The objective of this work was to evaluate the effects of supplemental feeding of soy waste on the feed intake and growth rate of goats. Twenty male crossbred (Boer x local) goats were assigned to two isonitrogenous diet groups: one of commercial pellet and the other of soy waste. The commercial pellet (1.0%) and soy waste (0.8%) were provided on the dry matter basis of body weight (BW) per day, to the respective group of each diet. The soy waste group had lower daily intakes of total dry matter (0.79 vs. 0.88 kg) and organic matter (665.71 vs. 790.44 g) than the group fed pellet; however, the differences on daily intakes for grass (0.62 vs. 0.64 kg), crude protein (96.81 vs. 96.83 g), and neutral detergent fibre (483.70 vs. 499.86 g) were not significant. No differences were observed between groups for BW gain. The feed conversion ratio and feed cost per kilogram of BW gain were lower for the group fed soy waste than for the one fed pellet. Goats fed supplemental soy waste have a lower total dry matter intake, feed conversion ratio, and feed cost per kilogram of body weight gain than those fed commercial pellets.

Characterization of membrane vesicles circulating in the serum of patients with common acute lymphoblastic leukemia.

Common acute lymphoblastic leukemia antigen detected by radioimmunoassay in the serum of patients with common acute lymphoblastic leukemia was found to be exclusively associated with the pellet of the serum samples obtained by ultracentrifugation at 100,000 X g. The pellets were shown to contain membrane vesicles or fragments which were characterized by electron microscopy and determination of enzymatic activity. The pelleted fragments had an apparent diameter ranging between 60 and 260 nm and showed a trilaminar membrane structure. On freeze-fracture preparations, the fragments with concave profile, corresponding to the external fracture face of plasma membrane, displayed an intramembrane particle density (ranging from 0 to 750 particles per micron2) which is similar to that recorded on the corresponding fracture face of intact cells from the common lymphoblastic leukemia antigen positive leukemic cell line (Nalm-1) or of vesicles shed in the culture medium by Nalm-1 cells. Furthermore, analysis of the membrane enzyme marker 5'-nucleotidase in the pellet of patient's sera, showed that the presence of this enzyme correlated with that of common lymphoblastic leukemia antigen, but the quantitative relationship between the two surface constituents was not linear. The results suggest that the two markers are located on the same membrane fragments, but that their individual distribution on the shed fragments is heterogeneous.

Gold recovery from cyanideand chloride solution using activated carbon

Uusia keinoja kullan erottamiseksi malmista on etsitty viimeaikoina taloudellisista ja ympäristöllisistä syistä kautta maailman. Syanidointimenetelmä on hallinnut kullan talteenottoayli sata vuotta. Menetelmässä kulta liuotetaan laimeaan syanidiliuokseen, jostase otetaan talteen aktiivihiilen avulla. Syanidin käyttöä pyritään kuitenkin vähentämään sen myrkyllisyyden takia. Lisäksi nykyään louhitaan enenemässä määrin malmia, josta on hankala rikastaa kulta kustannustehokkaasti syanidia käyttäen. Kullan talteenottoa syanidi- ja kloridiliuoksesta on selvitetty kirjallisuuden avulla. Kullan kemiaan liuotuksen aikana on perehdytty ennen kullan talteenottoa aktiivihiilellä. Aktiivihiilen elinkaari kullan adsorbenttinaon käsitelty valmistuksesta hylkäämiseen mukaan lukien hiilen myrkyttyminen prosessissa ja regenerointi. Aktiivi-hiilen käyttäytyminen syanidi- ja kloridiliuoksessa on selvitetty erikseen. Kullan talteenottoa kuparipitoisista malmeista on käsitelty. Kullan talteenottoa kloridiliuoksesta aktiivihiiltä käyttäen on tutkittu kokeellisesti. Pääasialliset tutkimuskohteet ovat adsorption kinetiikka, kuparin vaikutus adsorptioon, aktiivihiilen vaikutus adsorptioonja adsorboituneiden metallien strippaus hiilestä selektiivisesti. Hapettavan stippauksen vaikutus kullan desorptioon hiilestä on tutkittu yksityiskohtaisesti. Kullan erotusmenetelmät kuparimalmista aktiivihiiltä käyttäen on selvitetty diplomityön tulosten pohjalta. Diplomityön keskeisten tulosten perusteella kulta ei välttämättä saostu aktiivihiilen pinnalle kloridiliuoksesta. Havainto varmistettiin ladattujen hiilipartikkelien pyyhkäisyelektronimikroskooppikuvista ja partikkeleille tehdyistä mikroanalyyseistä. Kullan pelkistyminen metalliseksi kullaksi aktiivihiilessä voitaneen välttää käyttämällä erittäin hapettavia olosuhteita. Aktiivihiili ilmeisesti hapettuu näissä olosuhteissa, mikä mahdollistaa kultakloridin adsorboitumisen hiileen.

Solid and liquid biofuels markets in Finland - a study on international biofuels trade

This study considered the current situation of solid and liquid biofuels markets and international biofuels trade in Finland and identified the challenges ofthe emerging international biofuels markets for Finland. The fact that industryconsumes more than half of the total primary energy, widely applied combined heat and power production (CHP) and a high share of biofuels in the total energy consumption are specific to the Finnish energy system. One third of the electricity is generated in CHP plants. As much as 27% of the total energy consumption ismet by using wood and peat, which makes Finland the leading country in the use of biofuels. Finland has made a commitment to maintain greenhouse gas emissions at the 1990 level at the highest during the period 2008-2012. The Finnish energypolicy aims to achieve the target, and a variety of measures are taken to promote the use of renewable energy sources and especially wood fuels. In this study, the wooden raw material streams of the forest industry were included the international biofuels trade in addition to biomass streams that are traded for energy production. In 2004, as much as 45% of the raw wood importedinto Finland ended up in energy production. The total international trading of biofuels was evaluated at 72 PJ, of which the majority, 58 PJ, was raw wood. About 22% of wood based energy in Finland originated from imported raw wood. Tall oil and wood pellets composed the largest export streams of biofuels. The annual turnover of international biofuels trade was estimated at about ¤ 90 million fordirect trade and at about ¤ 190 million for indirect trade. The forest industryas the biggest user of wood, and the producer and user of wood fuels has a central position in biomass and biofuels markets in Finland. Lately, the international aspects of Finnish biofuels markets have been emphasised as the import of rawwood and the export of wood pellets have increased. Expanding the use of biofuels in the road transportation sector would increase the international streams ofbiofuels in Finland. In coming years, the international trading of biomass for energy purposes can be expected to continue growing.

Formation and Control of Trace Metal Emissions in Co-Firing of Biomass, Peat, and Wastes in Fluidised Bed Combustors

Environmentally harmful consequences of fossil fuel utilisation andthe landfilling of wastes have increased the interest among the energy producers to consider the use of alternative fuels like wood fuels and Refuse-Derived Fuels, RDFs. The fluidised bed technology that allows the flexible use of a variety of different fuels is commonly used at small- and medium-sized power plants ofmunicipalities and industry in Finland. Since there is only one mass-burn plantcurrently in operation in the country and no intention to build new ones, the co-firing of pre-processed wastes in fluidised bed boilers has become the most generally applied waste-to-energy concept in Finland. The recently validated EU Directive on Incineration of Wastes aims to mitigate environmentally harmful pollutants of waste incineration and co-incineration of wastes with conventional fuels. Apart from gaseous flue gas pollutants and dust, the emissions of toxic tracemetals are limited. The implementation of the Directive's restrictions in the Finnish legislation is assumed to limit the co-firing of waste fuels, due to the insufficient reduction of the regulated air pollutants in the existing flue gas cleaning devices. Trace metals emission formation and reduction in the ESP, the condensing wet scrubber, the fabric filter, and the humidification reactor were studied, experimentally, in full- and pilot-scale combustors utilising the bubbling fluidised bed technology, and, theoretically, by means of reactor model calculations. The core of the model is a thermodynamic equilibrium analysis. The experiments were carried out with wood chips, sawdust, and peat, and their refuse-derived fuel, RDF, blends. In all, ten different fuels or fuel blends were tested. Relatively high concentrations of trace metals in RDFs compared to the concentrations of these metals in wood fuels increased the trace metal concentrations in the flue gas after the boiler ten- to hundred-folds, when RDF was co-fired with sawdust in a full-scale BFB boiler. In the case of peat, lesser increase in trace metal concentrations was observed, due to the higher initial trace metal concentrations of peat compared to sawdust. Despite the high removal rate of most of the trace metals in the ESP, the Directive emission limits for trace metals were exceeded in each of the RDF co-firing tests. The dominat trace metals in fluegas after the ESP were Cu, Pb and Mn. In the condensing wet scrubber, the flue gas trace metal emissions were reduced below the Directive emission limits, whenRDF pellet was used as a co-firing fuel together with sawdust and peat. High chlorine content of the RDFs enhanced the mercuric chloride formation and hence the mercury removal in the ESP and scrubber. Mercury emissions were lower than theDirective emission limit for total Hg, 0.05 mg/Nm3, in all full-scale co-firingtests already in the flue gas after the ESP. The pilot-scale experiments with aBFB combustor equipped with a fabric filter revealed that the fabric filter alone is able to reduce the trace metal concentrations, including mercury, in the flue gas during the RDF co-firing approximately to the same level as they are during the wood chip firing. Lower trace metal emissions than the Directive limits were easily reached even with a 40% thermal share of RDF co-firing with sawdust.Enrichment of trace metals in the submicron fly ash particle fraction because of RDF co-firing was not observed in the test runs where sawdust was used as the main fuel. The combustion of RDF pellets with peat caused an enrichment of As, Cd, Co, Pb, Sb, and V in the submicron particle mode. Accumulation and release oftrace metals in the bed material was examined by means of a bed material analysis, mass balance calculations and a reactor model. Lead, zinc and copper were found to have a tendency to be accumulated in the bed material but also to have a tendency to be released from the bed material into the combustion gases, if the combustion conditions were changed. The concentration of the trace metal in the combustion gases of the bubbling fluidised bed boiler was found to be a summary of trace metal fluxes from three main sources. They were (1) the trace metal flux from the burning fuel particle (2) the trace metal flux from the ash in the bed, and (3) the trace metal flux from the active alkali metal layer on the sand (and ash) particles in the bed. The amount of chlorine in the system, the combustion temperature, the fuel ash composition and the saturation state of the bed material in regard to trace metals were discovered to be key factors affecting therelease process. During the co-firing of waste fuels with variable amounts of e.g. ash and chlorine, it is extremely important to consider the possible ongoingaccumulation and/or release of the trace metals in the bed, when determining the flue gas trace metal emissions. If the state of the combustion process in regard to trace metals accumulation and/or release in the bed material is not known,it may happen that emissions from the bed material rather than the combustion of the fuel in question are measured and reported.

Propagation of the Ignition Front against Airflow in Packed Beds of Wood Particles

Combustion of wood is increasing because of the needs of decreasing the emissions of carbon dioxide and the amount of waste going to landfills. Wood based fuels are often scattered on a large area. The transport distances should be short enough to prevent too high costs, and so the size of heating and power plants using wood fuels is often rather small. Combustion technologies of small-size units have to be developed to reach efficient and environmentally friendly energy production. Furnaces that use different packed bed combustion or gasification techniques areoften most economic in small-scale energy production. Ignition front propagation rate affects the stability, heat release rate and emissions of packed bed combustion. Ignition front propagation against airflow in packed beds of wood fuels has been studied. The research has been carried out mainly experimentally. Theoretical aspects have been considered to draw conclusions about the experimental results. The effects of airflow rate, moisture content of the fuel, size, shape and density of particles, and porosity of the bed on the propagation rate of the ignition front have been studied. The experiments were carried out in a pot furnace. The fuels used in the experiments were mainly real wood fuels that are often burned in the production of energy. The fuel types were thin wood chips, saw dust, shavings, wood chips, and pellets with different sizes. Also a few mixturesof the above were tested. Increase in the moisture content of the fuel decreases the propagation rates of the ignition front and makes the range of possible airflow rates narrower because of the energy needed for the evaporation of water and the dilution of volatile gases due to evaporated steam. Increase in the airflow rate increases the ignition rate until a maximum rate of propagation is reached after which it decreases. The maximum flame propagation rate is not always reached in stoichiometric combustion conditions. Increase in particle size and density transfers the optimum airflow rate towards fuel lean conditions. Mixing of small and large particles is often advantageous, because small particles make itpossible to reach the maximum ignition rate in fuel rich conditions, and large particles widen the range of possible airflow rates. A correlation was found forthe maximum rate of ignition front propagation in different wood fuels. According to the correlation, the maximum ignition mass flux is increased when the sphericity of the particles and the porosity of the bed are increased and the moisture content of the fuel is decreased. Another fit was found between sphericity and porosity. Increase in sphericity decreases the porosity of the bed. The reasons of the observed results are discussed.

Investigaciones sobre la detección, difusión natural y control del enrollamiento clorótico del albaricoquero

Se ha aplicado la técnica de la tinción con el fluorocromo DAPI (4'-6- diamidino- 2-fenilindol) a la detección de organismos del tipo micoplasma («mycoplasma-like organisms» o MLOs) y al seguimiento, a lo largo de un año, de la distribución de MLOs en albaricoqueros enfermos de enrollamiento clorótico («apricot chloroiic leaf roll» o ACLR). Los resultados obtenidos confirman la poca fiabilidad de esta técnica para la detección precoz de micoplasmosis en árboles frutales, a causa de la baja concentración e irregular distribución de MLOs dentro de los árboles enfermos. Én cambio, la tinción con DAPI es útil para la observación a lo largo del año de la distribución de MLOs en diferentes partes de los árboles infectados por ACLR. A lo largo del invierno y la primavera, los MLOs fueron detectados solamente en las raíces y en los ramos formados el año anterior. La presencia de MLOs en los nuevos brotes no pudo ser detectada hasta el principio del verano. En trabajos previos se observaron grandes variaciones en la difusión natural del ACLR, incluso entre áreas próximas de la misma provincia de Valencia. Las investigaciones efectuadas ahora sobre las poblaciones de cicadélidos han mostrado que tanto el número de especies como el de individuos capturados son superiores en un área con una importante difusión natural del ACLR que en otra zona donde la difusión de la enfermedad es prácticamente nula. Las diferencias entre los cicadélidos capturados en estas dos áreas han proporcionado indicaciones acerca de las especies que tienen más probabilidades de ser vectores del ACLR. Se ha estudiado también, durante tres años, la influencia de tratamientos insecticidas y herbicidas sobre la difusión natural del ACLR en una plantación de albaricoqueros. En la mitad de la plantación que se dejó sin tratar, el número de cicadélidos capturados, así como el de nuevos árboles con síntomas de ACLR fue mayor que en la parte de la plantación que había sido tratada.

Seospellettien pienpoltto

This work is a part of Vapos research over mixed pellets. In this work combustion of ten different mixed pellets are examined. This is done by two kinds of tests, burning tests and ash melting tests. First there is a short review how different bio fuels burn and what kind of problems they cause. After this burning characteristics and flue gas calculation methods are acquainted. In test part burning tests and ash melting tests and their results are reported. Lastly conclusions and considerations over further study are done.

Sachês absorvedores de etileno na pós-colheita de maçãs 'Royal Gala'

A redução dos níveis de etileno no ambiente de armazenamento é importante na preservação da qualidade pós-colheita de frutos. O presente trabalho teve por objetivo avaliar o efeito de sachês contendo pellets (10g) impregnados com absorvedor de etileno à base de permanganato de potássio (KMnO4), na preservação da qualidade pós-colheita de maçãs 'Royal Gala' armazenadas em câmara fria e em temperatura ambiente. O emprego de um ou dois sachês de produto, durante o armazenamento refrigerado convencional (dois meses a 0±0,5ºC/90-95% de UR) dos frutos, acondicionados em caixas de 18kg, envoltos em filme de polietileno de alta densidade (30µm), reduziu a concentração de etileno no interior da embalagem. Isto ocasionou maior retenção de cor verde na casca e de firmeza de polpa e menor incremento no teor de sólidos solúveis nos frutos, especialmente após uma semana de comercialização simulada (20±4ºC/70-80% de UR). Em temperatura ambiente, a utilização de um sachê de produto por caixa reduziu a concentração de etileno no interior das embalagens de polietileno e retardou o amadurecimento dos frutos em relação ao tratamentocontrole, sendo este efeito mais expressivo em frutos colhidos em estádios menos avançados de maturação. Os resultados obtidos mostram que o absorvedor de etileno à base de KMnO4 representa uma alternativa viável para a preservação da qualidade de maçãs 'Royal Gala', imediatamente após a colheita, durante o transporte refrigerado, na exportação de maçãs, bem como durante a comercialização, em temperatura ambiente.

Arvometallien selektiivinen erottaminen kloridiliuoksista

Työssä tutkittiin jalometallien selektiivistä erottamista kloridiliuoksista synteettisten polymeerihartsien avulla. Laboratoriokokeissa keskityttiin tutkimaan kullan erottamista hydrofiilisen polymetakrylaattipohjaisen adsorbentin avulla. Lähtökohtana oli platinarikaste, joka sisälsi kullan lisäksi platinaa, palladiumia, hopeaa, kuparia, rautaa, vismuttia, seleeniä ja telluuria. Mittauksissa tutkittiin eri metallien ja puolimetallien adsorptiota hartsiin tasapaino-, kinetiikka- ja kolonnikokeilla. Työssä käytettiin myös adsorption simulointiin monikomponenttierotuksen dynaamiseen mallintamiseen tarkoitettua tietokoneohjelmaa, johon tarvittavat parametrit estimoitiin kokeellisen datan avulla. Tasapainokokeet yhtä metallia sisältäneistä liuoksista osoittivat, että hartsi adsorboi tehokkaasti kultaa kaikissa tutkituissa suolahappopitoisuuksissa (1-6 M). Kulta muodostaa hartsiin hyvin adsorboituvia tetrakloroauraatti(III)ioneja, [AuCl4]-, jotka ovat erittäin stabiileja pieniin kloridipitoisuuksiin saakka. Suolahappopitoisuudella oli merkitystä ainoastaan raudan adsorptioon, joka kasvoi huomattavasti suolahappopitoisuuden noustessa johtuen raudan taipumuksesta muodostaa hyvin adsorboituvia [FeCl4]--ioneja väkevissä suolahappopitoisuuksissa. Muiden tutkittujen alkuaineiden adsorptiot jäivät alhaisiksi kaikilla suolahappopitoisuuksilla. Rikasteliuoksella tehdyt tasapainokokeet osoittivat, että adsorptiokapasiteetti kullalle riippuu voimakkaasti muista läsnäolevista komponenteista. Kilpaileva adsorptio kuvattiin Langmuir-Freundlich-isotermillä. Kolonnikokeet osoittivat, että hartsi adsorboi kullan lisäksi hieman myös rautaa ja telluuria, jotka saatiin kuitenkin eluoitua hartsista täysin 5 M suolahappopesulla ja sitä seuraavalla 1 M suolahappopesulla. Tehokkaaksi liuokseksi kullan desorboimiseen osoittautui asetonin ja 1 M suolahapon seos. Kolonnierotuksen eri vaiheet pystyttiin tyydyttävästi kuvaamaan simulointimallilla.

Pientalon teknisen tilan tuotteistus

Diplomityön tavoitteena on selvittää asiakkaiden toiveita ja arvostuksia, joiden avulla voidaan rakentaa silta teknisiin ominaisuuksiin ja niiden variointiin. Rinnakkaisena työnä lähinnä teknisestä näkökulmasta teki Lauri Manninen omaa tutkimustyötä. Tässä raportissa on teknisiä ominaisuuksia käsiteltäessä lainattu Mannisen työtä. Pientaloa suunniteltaessa on valittava mm. lämmitysjärjestelmä ja talotekniikan taso. Suomessa pientaloihin on tarjolla useita lämmitysjärjestelmävaihtoehtoja. Tunnetuimpia päälämmönlähteitä ovat maa, puu, pelletti, öljy, kaasu, sähkö ja kaukolämpö. Lämmitysjärjestelmän lisäksi teknisiin tiloihin sijoitetaan muuta talotekniikkaa. Tässä diplomityössä tarkastellaan eri lämmitysjärjestelmien nykytilannetta sekä mahdollisuuksien mukaan tulevaisuuden näkymiä. Työssä on käytetty lähdeaineistona kirjallisuutta, www-sivuja sekä haastatteluja. Työhön on haastateltu yksityisasiakkaita. Lämmitysjärjestelmien nykytilanteen ja tulevaisuuden näkymien sekä haastatteluissa esiin tulleiden asioiden avulla on pyritty kehittämään talotekniikkamarkkinoille uusia tuote- ja palvelukonsepteja. Diplomityössä on käsitelty lämmitysjärjestelmiä sekä talotekniikkaa markkinatilanteen ja asiakkaiden näkökulmasta. Tuloksena työssä esitetään alustava tuotteistussuunnitelma ja ideoita teknisen tilan kokonaispalvelun tuotteistamiseen.

Geology of the Cerro-Quema Au-Cu deposit (Azuero Peninsula, Panama)

The Cerro Quema district, located on the Azuero Peninsula, Panama, is part of a large regional hydrothermal system controlled by regional faults striking broadly E-W, developed within the Río Quema Formation. This formation is composed of volcanic, sedimentary and volcano-sedimentary rocks indicating a submarine depositional environment, corresponding to the fore-arc basin of a Cretaceous-Paleogene volcanic arc. The structures observed in the area and their tectono-stratigraphic relationship with the surrounding formations suggest a compressive and/or transpressive tectonic regime, at least during Late Cretaceous-Oligocene times. The igneous rocks of the Río Quema Formation plot within the calc-alkaline field with trace and rare earth element (REE) patterns of volcanic arc affinity. This volcanic arc developed on the Caribbean large igneous province during subduction of the Farallon Plate. Mineralization consists of disseminations of pyrite and enargite as well as a stockwork of pyrite and barite with minor sphalerite, galena and chalcopyrite, hosted by a subaqueous dacitic lava dome of the Río Quema Formation. Gold is present as submicroscopic grains and associated with pyrite as invisible gold. A hydrothermal alteration pattern with a core of advanced argillic alteration (vuggy silica with alunite, dickite, pyrite and enargite) and an outer zone of argillic alteration (kaolinite, smectite and illite) has been observed. Supergene oxidation overprinted the hydrothermal alteration resulting in a thick cap of residual silica and iron oxides. The ore minerals, the alteration pattern and the tectono-volcanic environment of Cerro Quema are consistent with a high sulfidation epithermal system developed in the Azuero peninsula during pre-Oligocene times.

Puupellettien tuotanto-, jakelu- ja käyttöketjun tekniikka, talous ja markkinat

Puupelletti on puumurskeesta puristamalla valmistettu polttoainejaloste, jonka raaka- aineita ovat mekaanisen metsäteollisuuden sivutuotteet kutterinlastu ja sahanpuru. Sylinterin muotoiset pelletit ovat yleensä halkaisijaltaan 6-10 mm ja pituudeltaan 10 - 30 mm. Tässä diplomityössä tarkastellaan pellettiketjua valmistuksesta loppukäyttöön. Työ sisältää valmistuksen, kuljetuksen ja käytön niin tekniset puolet, kuin taloudelliset näkökohdatkin. Myös muiden maiden pellettimarkkinoiden tilanne tuodaan esille. Työn lopussa kuvataan muutama case-esimerkki onnistuneista pellettiketjuista. Suomessa puupellettimarkkinoiden kehitys alkoi 1998 Vöyrissä auenneen pellettitehtaan myötä. Pellettien tuotanto ja kulutus ovat sen jälkeen kasvaneet nopeasti ja nyt vuonna 2001 pellettien tuotantokapasiteetti on 150 000 t/a. Pellettimarkkinoiden nopea kehitys Suomessa perustuu öljyn korkeaan hintaan, käytön helppouteen ja ympäristöystävällisyyteen. Käyttölaitteistojen yleistyessä ja jakelun tehostuessa pellettiliiketoiminta tulee vahvistamaan asemaansa entisestään Suomessa