Data on multidisciplinary research in the Tajura Rift (Gulf of Aden) during Cruise 7 of R/V Akademik Mstislav Keldysh in winter 1983-1984

In the collective monograph results of geological and geophysical studies in the Tadjura Rift carried out by conventional outboard instruments and from deep/sea manned submersibles "Pisces" in winter 1983-1984 are reported. Main features of rift tectonics, geology, petrology, and geochemistry of basalts from the rift are under consideration. An emphasis is made on lithology, stratigraphy, and geochemistry of bottom sediments. Roles of terrigenous, edafogenic, biogenic, and hydrothermal components in formation of bottom sediments from the rift zone are shown.

Composition and age of ores and bottom sediments accumulated within and near the Rainbow hydrothermal field

Results of direct geological and geochemical observations of the modern Rainbow hydrothermal field (Mid-Atlantic Ridge, 36°14'N; 33°54'W) carried out from the deep-sea manned Mir submersibles during Cruises 41 and 42 of the R/V Akademik Mstislav Keldysh in 1998-1999 and data of laboratory studies of collected samples are under consideration in the paper. The field lacks neovolcanic rocks and the axial part of the rift is filled in with a serpentinite protrusion. In this field there occur metalliferous sediments, as well as active and relict sulfide edifices composed of sulfide minerals; pyrrhotite, chalcopyrite, isocubanite, sphalerite, marcasite, pyrite, bornite, chalcosine, digenite, magnetite, anhydrite, rare troilite, wurtzite, millerite, and pentlandite have been determined. Sulfide ores are characterized by concentric-zoned textures. During in situ measurements during 35 minutes temperature of hydrothermal fluids was varying within a range from 250 to 350°C. Calculated chemical and isotopic composition of hydrothermal fluid shows elevated concentrations of Cl, Ni, Co, CH4, and H2. Values of d34S of H2S range from +2.4 to +3.1 per mil, of d13C of CH4 from -15.2 to -11.2 per mil, and d13C of CO2 from +1.0 to -4.0 per mil. Fluid inclusions are homogenized at temperatures from 140 to 360°C, whereas salinity of the fluid varies from 4.2 to 8.5 wt %. d34S values of sulfides range from +1.3 to +12.5 per mil. 3He/4He ratio in mineral-forming fluid contained in the fluid inclusions from sulfides of the Rainbow field varies from 0.00000374 to 0.0000101. It is shown that hydrothermal activity in the area continues approximately during 100 ka. It is assumed that the fluid and sulfide edifices contain components from the upper mantle. A hypothesis of phase separation of a supercritical fluid that results in formation of brines is proposed. Hydrothermal activity is related to the tectonic, not volcanic, phase of the Mid-Atlantic Ridge evolution.

Concentrations of Fe, Mn, Cu, Zn, Co, Ni, Pb, Cd, B, and SiO2 in interstitial waters from bottom sediments of the Atlantis II and Discovery Deeps, Red Sea rift zone

Chemical analyzes show that interstitial waters from ore-bearing bottom sediments of the Atlantis II and Discovery Deeps are enriched in Fe, Mn, Cu, Ni, Co, Zn, Pb, and Cd compared to sea water. Enrichment factors of these trace elements in the interstitial waters of the Atlantis II Deep relative to the sea water vary within the following ranges: for Fe from 100 to 7000, for Mn from 19047 to 32738, for Zn from 500 to 1600, for Pb from 78333 to 190000, for Cu from 107 to 654. Comparison of average weighted concentrations of Fe, Mn, Zn, Pb, Cu, Ni in the bottom sediments and the interstitial waters of the Atlantis II Deep indicates common regularities and good relationship in distribution of these elements along sediment cores. Differences in concentrations and distribution of the studied trace elements in the interstitial waters of the Atlantis II and Discovery Deeps result from different chemical compositions of hydrothermal fluids entering these deeps.

Synthesis of medium-chain-length polyhydroxyalkanoates in Arabidopsis thaliana using intermediates of peroxisomal fatty acid β-oxidation

Polyhydroxyalkanoate (PHA) is a family of polymers composed primarily of R-3-hydroxyalkanoic acids. These polymers have properties of biodegradable thermoplastics and elastomers. Medium-chain-length PHAs (MCL-PHAs) are synthesized in bacteria by using intermediates of the β-oxidation of alkanoic acids. To assess the feasibility of producing MCL-PHAs in plants, Arabidopsis thaliana was transformed with the PhaC1 synthase from Pseudomonas aeruginosa modified for peroxisome targeting by addition of the carboxyl 34 amino acids from the Brassica napus isocitrate lyase. Immunocytochemistry demonstrated that the modified PHA synthase was appropriately targeted to leaf-type peroxisomes in light-grown plants and glyoxysomes in dark-grown plants. Plants expressing the PHA synthase accumulated electron-lucent inclusions in the glyoxysomes and leaf-type peroxisomes, as well as in the vacuole. These inclusions were similar to bacterial PHA inclusions. Analysis of plant extracts by GC and mass spectrometry demonstrated the presence of MCL-PHA in transgenic plants to approximately 4 mg per g of dry weight. The plant PHA contained saturated and unsaturated 3-hydroxyalkanoic acids ranging from six to 16 carbons with 41% of the monomers being 3-hydroxyoctanoic acid and 3-hydroxyoctenoic acid. These results indicate that the β-oxidation of plant fatty acids can generate a broad range of R-3-hydroxyacyl-CoA intermediates that can be used to synthesize MCL-PHAs.

Síntese, caracterização e atividade catalítica de compostos organolantanídeos contendo os ânions metanossulfonato e pentametilciclopentadienil e o ligante pirazinamida

O estudo de compostos organolantanídeos consiste em um dos campos de maior interesse dentro da química organometálica, principalmente devido ao uso potencial como precursores ou catalisadores em reações de hidrogenação, hidroformilação, carbonilação, oxidação e principalmente polimerização de olefinas. Este interesse tem levado diversos grupos de pesquisa a sintetizarem compostos utilizando o ânion ciclopentadienil e seus derivados ligados a íons lantanídeos (III). O presente trabalho tem como objetivo contribuir para a aplicação desses compostos organolantanídeos como catalisadores em reações de polimerização de olefinas. O trabalho envolveu uma etapa de síntese e caracterização de duas classes de compostos organolantanídeos Ln(MS)2Cp*(Ln = Tb e Yb), e Ln(MS)2Cp*PzA (Ln = Sm, Tb e Yb) e uma etapa de estudo da atividade catalítica desses compostos frente a reações de polimerização de etileno, propileno e estireno, utilizando metilaluminoxano como co-catalisador e a caracterização dos polímeros formados. Os compostos sintetizados apresentaram atividade catalítica apenas para polimerização de estireno. O polímero formado, independente do composto organolantanídeo utilizado, foi caracterizado como poliestireno principalmente atático, indicando que a polimerização não é estereoespecífica e apresentou massa molar da ordem de 104 g/mol.

Preparation, characterisation and testing of CuO/Ce0.8Zr0.2O2 catalysts for NO oxidation to NO2 and mild temperature diesel soot combustion

CuO/ceria-zirconia catalysts have been prepared, deeply characterised (N2 adsorption–desorption isotherms at −196 °C, XRD, Raman spectroscopy, XPS, TEM and H2-TPR) and tested for NO oxidation to NO2 in TPR conditions, and for soot combustion at mild temperature (400 °C) in a NOx/O2 stream. The behaviour has been compared to that of a reference Pt/alumina commercial catalyst. The ceria-zirconia support was prepared by the co-precipitation method, and different amounts of copper (0.5, 1, 2, 4 and 6 wt%) were loaded by incipient wetness impregnation. The results revealed that copper is well-dispersed onto the ceria-zirconia support for the catalysts with low copper loading and CuO particles were only identified by XRD in samples with 4 and 6% of copper. A very low loading of copper increases significantly the activity for the NO oxidation to NO2 with regard to the ceria-zirconia support and an optimum was found for a 4% CuO/ceria-zirconia composition, showing a very high activity (54% at 348 °C). The soot combustion rate at 400 °C obtained with the 2% CuO/ceria-zirconia catalyst is slightly lower to that of 1% Pt/alumina in terms of mass of catalyst but higher in terms of price of catalyst.

Synthesis of high surface area TiO2 nanoparticles by mild acid treatment with HCl or HI for photocatalytic propene oxidation

Nanostructured TiO2 photocatalysts with small crystalline sizes have been synthesized by sol-gel using the amphiphilic triblock copolymer Pluronic P123 as template. A new synthesis route, based on the treatment of TiO2 xerogels with acid-ethanol mixtures in two different steps, synthesis and extraction-crystallization, has been investigated, analyzing two acids, hydrochloric and hydriodic acid. As reference, samples have also been prepared by extraction-crystallization in ethanol, being these TiO2 materials amorphous and presenting higher porosities. The prepared materials present different degrees of crystallinity depending on the experimental conditions used. In general, these materials exhibit high surface areas, with an important contribution of microporosity and mesoporosity, and with very small size anatase crystals, ranging from 5 to 7 nm. The activity of the obtained photocatalysts has been assessed in the oxidation of propene in gas phase at low concentration (100 ppmv) under a UVA lamp with 365 nm wavelength. In the conditions studied, these photocatalysts show different activities in the oxidation of propene which do not depend on their surface areas, but on their crystallinity and band gap energies, being sample prepared with HCl both during synthesis and in extraction-crystallizations steps, the most active one, with superior performance than Evonik P25.

Enantioselective Synthesis of Succinimides by Michael Addition of Aldehydes to Maleimides Organocatalyzed by Chiral Primary Amine-Guanidines

The monoguanylation of (1S,2S)- and (1R,2R)-cyclohexane-1,2-diamine affords chiral primary amine-guanidines that are used as chiral organocatalysts in the enantioselective Michael addition of aldehydes, particularly α,α-disubstituted aldehydes, to maleimides. The reaction is carried out in the presence of imidazole, as an additive, in aqueous N,N-dimethylformamide, as the solvent, and affords the corresponding enantioenriched succinimides in high or quantitative yields with enantioselectivities up to 96 % ee. Theoretical calculations (DFT and M06–2X) suggest a different hydrogen-bonding coordination pattern between the maleimide (C=O) and the catalyst (NH groups) is responsible for the enantioinduction switch that is observed when the reaction is carried out using primary amine-guanidines versus primary amine-thioureas as the organocatalysts.

Enantioselective Synthesis of Succinimides by Michael Addition of 1,3-Dicarbonyl Compounds to Maleimides Catalyzed by a Chiral Bis(2-aminobenzimidazole) Organocatalyst

A wide variety of chiral succinimides have been prepared in high yields and enantioselectivities by asymmetric conjugate addition of 1,3-dicarbonyl compounds to maleimides under very mild reaction conditions using a bifunctional benzimidazole-derived organocatalyst. Computational and NMR studies support the hydrogen-bonding activation role of the catalyst and the origin of the stereoselectivity of the process.

Total oxidation of naphthalene at low temperatures using palladium nanoparticles supported on inorganic oxide-coated cordierite honeycomb monoliths

A study on the preparation of thin films of ZSM-5 and BETA zeolites, and a SAPO-5 silicoaluminophosphate, supported on cordierite honeycomb monoliths by in situ synthesis was carried out for their use as catalyst supports. Furthermore γ-Al2O3 was also coated onto a cordierite honeycomb monolith by a dip-coating method for use as a standard support. Structured monolithic catalysts were prepared by impregnation of the aforementioned coated monoliths with polymer-protected Pd nanoparticles. The monolithic catalysts have been tested for the total oxidation of naphthalene (100 ppm, GHSV 1220 h−1). From the combined use of the zeolite with polymer-protected nanoparticles, enhanced catalytic properties have been found for the total abatement of naphthalene. The Pd/MBETA and Pd/MZSM-5 catalytic monoliths have shown excellent activity with a high degree of stability, even after undergoing accelerated ageing experiments.

Influence of peroxometallic intermediaries present on polyoxometalates nanoparticles surface on the adipic acid synthesis

The cyclohexene oxidation by hydrogen peroxide catalysed by polyoxometalates (POM) has been shown as an adequate green route for the adipic acid synthesis. In this study, it has been demonstrated that POM's salts are effective catalysts for this reaction and how peroxopolyoxometalates intermediaries are the truly responsible species of the POM's salts catalytic activity and solubility. However, the latter can be reduced by calcining the catalyst previously. Polyoxomolybdates salts generally present a higher activity than polyoxotungstenates salts. Finally, it must be remarked the positive effect exerted by the acetic acid stabilising the peroxide of hydrogen against its decomposition.

Hydrothermal Carbons from Hemicellulose-Derived Aqueous Hydrolysis Products as Electrode Materials for Supercapacitors

Acid pretreatment of lignocellulosic biomass, required for bioethanol production, generates large amounts of by-products, such as lignin and hydrolyzed hemicellulose fractions, which have found so far very limited applications. In this work, we demonstrate how the recovered hemicellulose hydrolysis products can be effectively utilized as a precursor for the synthesis of functional carbon materials through hydrothermal carbonization (HTC). The morphology and chemical structure of the synthesized HTC carbons are thoroughly characterized to highlight their similarities with glucose-derived HTC carbons. Furthermore, two routes for introducing porosity within the HTC carbon structure are presented: i) silica nanoparticle hard-templating, which is shown to be a viable method for the synthesis of carbonaceous hollow spheres; and ii) KOH chemical activation. The synthesized activated carbons (ACs) show an extremely high porosity (pore volume≈1.0 cm3 g−1) mostly composed of micropores (90 % of total pore volume). Because of their favorable textural properties, the ACs are further tested as electrodes for supercapacitors, yielding very promising results (300 F g−1 at 250 mA g−1) and confirming the high suitability of KOH-activated HTC carbons derived from spruce and corncob hydrolysis products as materials for electric double layer supercapacitors.

Synthesis of Dihydroisobenzofurans via Palladium-Catalyzed Sequential Alkynylation/Annulation of 2-Bromobenzyl and 2-Chlorobenzyl Alcohols under Microwave Irradiation

The palladium-catalyzed synthesis of dihydroisobenzofurans has been performed by sequential Sonogashira cross-coupling/cyclization reactions between terminal alkynes and 2-(hydroxymethyl)bromo- and chlorobenzenes in methanol as solvent at 130 °C under microwave irradiation. A 4,4′-dichlorobenzophenone oxime-derived chloro-bridged palladacycle is an efficient pre-catalyst to perform this tandem process using 2-dicyclohexylphosphanyl-2′,4′,6′-triisopropylbiphenyl (Xphos) as ancillary ligand and potassium hydroxide as base in the absence of a copper cocatalyst. Under these conditions, functionalized 2-bromo- and 2-chlorobenzaldehydes are also suitable partners in the domino process affording phthalans in good yields. All the reactions can be performed under air and employing reagent-grade chemicals under low loading conditions (1 mol% Pd).

Cobalt-Impregnated Magnetite as General Heterogeneous Catalyst for the Hydroacylation Reaction of Azodicarboxylates

Catalysts consisting of cobalt and nickel impregnated on magnetite have been prepared, characterized and used for the hydroacylation reaction of different azodicarboxylate compounds with aldehydes, using nearly stoichiometric amounts of both reagents in only 3 h. Furthermore, this reaction has been conducted with the smallest amount of catalyst. The cobalt catalyst is stable enough to be removed by magnetic decantation and recycled ten-fold without any detrimental effect on the results.

Palladium(II) oxide impregnated on magnetite as a catalyst for the synthesis of 4-arylcoumarins via a Heck-arylation/cyclization process

Heck-arylation/cyclization was achieved using heterogeneous palladium(II) oxide impregnated on magnetite catalyst (2.5 mol%) with a lower catalyst loading than that reported for similar processes. Ethanol was used as a non-toxic and bio-renewable solvent. Good yields were afforded using a broad range of substrates (40–98%). The catalyst could be partially recycled, and analyses confirmed the almost total reduction of palladium(II) oxide to palladium(0) as well as the iodine poissoning effect, which is the main barrier to complete recyclability.