Study on peak overpressure and flame propagation speed of gas deflagration in the tube with obstacles

The on-way peak overpressure and flame propagation speed of gas deflagration in the tube with obstacles are important data for process safety. Based on carbon monoxide deflagration experiments, the paper presents a multi-zone integration model for calculation of on-way peak overpressure, in which the tube with obstacles is considered as a series of venting explosion enclosures which link each others. The analysis of experimental data indicates that the on-way peak overpressure of gas deflagration can be correlated as an empirical formula with equivalence ratio of carbon monoxide oxidation, expansion ratio, flame path length, etc., and that the on-way peak overpressure exhibits a linear relationship with turbulence factor and flame propagation speed. An empirical formula of flame propagation speed is given.

Speed of the internal pellet target in CSRm

Pellet target is one of the main candidate targets in CSRm (cooler storage ring’s main ring) for hadron physics studies. Pellet speed is an important physical parameter for the target. Larger pellet speed could shorten the interacting time interval between the pellet and the cyclotron beam, and thus results in a small temperature variation for the pellet. This could make the pellet facility work in a stable condition. A fluid dynamic simulation was carried out for the pellet speed, and it was found that the maximum speed for the target pellet may be restricted to about 100 m/s even if all working parameters were set to their optimal values.

Speed of the internal pellet target in CSRm

Pellet target is one of the main candidate targets in CSRm (cooler storage ring’s main ring) for hadron physics studies. Pellet speed is an important physical parameter for the target. Larger pellet speed could shorten the interacting time interval between the pellet and the cyclotron beam, and thus results in a small temperature variation for the pellet. This could make the pellet facility work in a stable con-dition. A fluid dynamic simulation was carried out for the pellet speed, and it was found that the maxi-mum speed for the target pellet may be restricted to about 100 m/s even if all working parameters were set to their optimal values.

Brittle-tough transition in PP/EPDM blends: effects of interparticle distance and tensile deformation speed

The toughness of polypropylene (PP)/ethylene-propylene-diene monomer rubber (EPDM) blends containing various EPDM contents as a function of the tensile speed was studied. The toughness of the blends was determined from the tensile fracture energy of the side-edge notched samples. A sharp brittle-tough transition was observed in the fracture energy versus interparticle distance (ID) curves when the crosshead speed < 102.4 mm/min. It was observed that the brittle-ductile transition of PP/EPDM blend occurred either by reducing ID or by decreasing the tensile speed. The correlation between the critical interparticle distance and tensile deformation rate was compared with that between the critical interparticle distance and temperature for PP/EPDM blends. (C) 2000 Elsevier Science Ltd. All rights reserved.

On SAR wind speed ambiguities and related geophysical model functions

Recent investigations show that normalized radar cross sections for C-band microwave sensors decrease under high wind conditions with certain incident angles instead of increase, as is the case for low to moderate wind speeds. This creates the problem of ambiguities in high wind speed retrievals from synthetic aperture radar (SAR). In the present work, four geophysical model functions (GMFs) are studied, namely the high wind C-band model 4 (CMOD4HW), C-band model 5 (CMOD5), the high wind vertical polarized GMF (HWGMF_VV), and the high wind horizontal polarized GMF (HWGMF_HH). Our focus is on model behaviours relative to wind speed ambiguities. We show that, except for CMOD4HW, the other GMFs exhibit the wind speed ambiguity problem. To consider this problem in high wind speed retrievals from SAR, we focus on hurricanes and propose a method to remove the speed ambiguity using the dominant hurricane wind structure.

Speed ambiguity in hurricane wind retrieval from SAR imagery

Under strong ocean surface wind conditions, the normalized radar cross section of synthetic aperture radar (SAR) is dampened at certain incident angles, compared with the signals under moderate winds. This causes a wind speed ambiguity problem in wind speed retrievals from SAR, because two solutions may exist for each backscattered signal. This study shows that the problem is ubiquitous in the images acquired by operational space-borne SAR sensors. Moreover, the problem is more severe for the near range and range travelling winds. To remove this ambiguity, a method was developed based on characteristics of the hurricane wind structure. A SAR image of Hurricane Rita (2005) was analysed to demonstrate the wind speed ambiguity problem and the method to improve the wind speed retrievals. Our conclusions suggest that a speed ambiguity removal algorithm must be used for wind retrievals from SAR in intense storms and hurricanes.

Spatial and temporal variations of sound speed at the PN section

Gridded sound speed data were calculated using Del Grosso's formulation from the temperature and salinity data at the PN section in the East China Sea covering 92 cruises between February 1978 and October 2000. The vertical gradients of sound speed are mainly related to the seasonal variations, and the strong horizontal gradients are mainly related to the Kuroshio and the upwelling. The standard deviations show that great variations of sound speed exist in the upper layer and in the slope zone. Empirical orthogonal function analysis shows that contributions of surface heating and the Kuroshio to sound speed variance are almost equivalent.

An efficient combination of supercritical fluid extraction and high-speed counter-current chromatography to extract and purify homoisoflavonoids from Ophiopogon japonicus (Thunb.) Ker-Gawler

Supercritical fluid extraction (SFE) was used to extract homoisoflavonoids from Ophiopogon japonicus (Thunb.) Ker-Gawler. The optimization of parameters was carried out using an orthogonal test L-9 (3)(4) including pressure, temperature, dynamic extraction time and the amount of modifier. The process was then scaled up by 100 times with a preparative SFE system under the optimized conditions of 25 MPa, 55 degrees C, 4.0 h and 25% methanol as a modifier. Then crude extracts were separated and purified by high-speed counter-current chromatography (HSCCC) with a two-phase solvent system composed of n-hexane/ethyl acetate/methanol/ACN/water (1.8:1.0:1.0:1.2:1.0 v/v). There three homoisoflavonoidal compounds including methylophiopogonanone A 6-aldehydo-isoophiopogonone A, and 6-formyl-isoophiopogonanone A, were successfully isolated and purified in one step. The collected fractions were analyzed by HPLC. In each operation, 140 mg crude extracts was separated and yielded 15.3 mg of methylophiopogonanone A (96.9% purity), 4.1 mg of 6-aldehydo-isoophiopogonone A (98.3% purity) and 13.5 mg of 6-formyl-isoophiopogonanone A (97.3% purity) respectively. The chemical structure of the three homoisoflavonoids are identified by means of ESI-MS and NMR analysis.

One step isolation and purification of liquiritigenin and isoliquiritigenin from Glycyrrhiza uralensis Risch using high-speed counter-current chromatography

High-speed counter-current chromatography (HSCCC) technique in semi-preparative scale has been successfully applied to the separation of bioactive flavonoid compounds, liquiritigenin and isoliquiritigenin in one step from the crude extract of Glycyrrhiza uralensis Risch. The HSCCC was performed using a two-phase solvent system composed of n-hexane-ethyl acetate-methanol-acetonitrile-water (2:2:1:0.6:2, v/v). Yields of liquiritigenin (98.9% purity) and isoliquiritigenin (98.3% purity) obtained were 0.52% and 0.32%. Chemical structures of the purified liquiritigenin and isoliquiritigenin were identified by electrospray ionization-MS (ESI-MS) and NMR analysis. (c) 2005 Published by Elsevier B.V.

Separation of neutral compounds by high speed capillary electrochromatography

With using short capillary column packed with porous and non-porous ODS stationary phases, high speed separation of 6 neutral aromatic compounds within 36 s by capillary electrochromatography (CEC) has been performed. Good reproducibility of the migration times for those solutes in high speed CEC was observed with RSD less than 1%. Both the linear velocity of EOF and the current linearly increases with the applied voltage, which means that the thermal effect by Joule heating was small. However, the capacity factor of solutes was found to decrease with the increase of the applied voltage, which was caused by the fact that about several seconds needed for the increase of voltage from 0 to applied value on a commercial CE instrument made larger contributions to the migration times of the early eluted compounds than those of lately eluted ones during high speed CEC, and voltage effect would increase with the higher applied voltage used. The linear relationship between the logarithm of capacity factor and the number of carbon for homologous compounds was observed, and positive value of slope means that the hydrophobicity of solutes is one of the main contribution factors to retention in high speed CEC packed with ODS stationary phases.

汉字早期字形加工

The researches of the CC's form processing mainly involved the effects of all kinds of form properties. In most of the cases, the researches were conducted after the lexical process completed. A few which was about early phases of visual perception focused on the process of feature extraction in character recognition. Up till now, nobody put forward a propose that we should study the form processing in the early phases of visual perception of CC. We hold that because the form processing occurs in the early phases of visual perception, we should study the processing prelexically. Moreover, visual perception of CC is a course during which the CC becomes clear gradually, so that the effects of all kinds of form properties should not be a absolute phenomena of an all-or-none. In this study we adopted 4 methods to research the form processing in the early phases simulatedly and systematically, including the tachistoscopic repetition, increasing time to present gradually, enlarging the visual angle gradually and non- tachistoscopic searching and naming. Under all kinds of bad or degraded visual conditions, the instantaneous course of early-phases processing was slowed down and postponed, and then the growth course was open to before our eyes. We can captured the characteristics of the form processing in the early phases by analyzing the reaction speed and recognition accuracy. Accompanying the visual angle and time increasing, the clarity improved and we can find out the relation between the effects of form properties and visual clarity improving. The results were as follows: ①in the early phases of visual perception of CC, there were the effects of all kinds of form properties. ②the quantity of the effects would cut down when the visual conditions were being changed better and better. We raised the concept of character's space transparency and it's algorithm to explain these effects of form properties. Furthermore, a model was discussed to help understand the phenomenon that the quantity of the effects changed as the visual conditions were improved. ③The early phases of visual perception of CC isn't the loci of the frequency effect.

Robust, High-Speed Network Design for Large-Scale Multiprocessing

As multiprocessor system size scales upward, two important aspects of multiprocessor systems will generally get worse rather than better: (1) interprocessor communication latency will increase and (2) the probability that some component in the system will fail will increase. These problems can prevent us from realizing the potential benefits of large-scale multiprocessing. In this report we consider the problem of designing networks which simultaneously minimize communication latency while maximizing fault tolerance. Using a synergy of techniques including connection topologies, routing protocols, signalling techniques, and packaging technologies we assemble integrated, system-level solutions to this network design problem.

Large-pore mesoporous SBA-15 silica particles with submicrometer size as stationary phases for high-speed CEC separation

A new mesoporous sphere-like SBA-15 silica was synthesized and evaluated in terms of its suitability as stationary phases for CEC. The unique and attractive properties of the silica particle are its submicrometer particle size of 400 nm and highly ordered cylindrical mesopores with uniform pore size of 12 nm running along the same direction. The bare silica particles with submicrometer size have been successfully employed for the normal-phase electrochromatographic separation of polar compounds with high efficiency (e.g., 210 000 for thiourea), which is matched well with its submicrometer particle size. The Van Deemeter plot showed the hindrance to mass transfer because of the existence of pore structure. The lowest plate height of 2.0 mu m was obtained at the linear velocity of 1.1 mm/s. On the other hand, because of the relatively high linear velocity (e.g., 4.0 mm/s) can be generated, high-speed separation of neutral compounds, anilines, and basic pharmaceuticals in CEC with C-18-modified SBA-15 silica as stationary phases was achieved within 36, 60, and 34 s, respectively.

Aphasia rehabilitation and the strange neglect of speed.

Timing data is infrequently reported in aphasiological literature and time taken is only a minor factor, where it is considered at all, in existing aphasia assessments. This is not surprising because reaction times are difficult to obtain manually, but it is a pity, because speed data should be indispensable in assessing the severity of language processing disorders and in evaluating the effects of treatment. This paper argues that reporting accuracy data without discussing speed of performance gives an incomplete and potentially misleading picture of any cognitive function. Moreover, in deciding how to treat, when to continue treatment and when to cease therapy, clinicians should have regard to both parameters: Speed and accuracy of performance. Crerar, Ellis and Dean (1996) reported a study in which the written sentence comprehension of 14 long-term agrammatic subjects was assessed and treated using a computer-based microworld. Some statistically significant and durable treatment effects were obtained after a short amount of focused therapy. Only accuracy data were reported in that (already long) paper, and interestingly, although it has been a widely read study, neither referees nor subsequent readers seemed to miss "the other side of the coin": How these participants compared with controls for their speed of processing and what effect treatment had on speed. This paper considers both aspects of the data and presents a tentative way of combining treatment effects on both accuracy and speed of performance in a single indicator. Looking at rehabilitation this way gives us a rather different perspective on which individuals benefited most from the intervention. It also demonstrates that while some subjects are capable of utilising metalinguistic skills to achieve normal accuracy scores even many years post-stroke, there is little prospect of reducing the time taken to within the normal range. Without considering speed of processing, the extent of this residual functional impairment can be overlooked.