Influence of high insertion torque on implant placement - an anisotropic bone stress analysis

The aim of this study was to evaluate the influence of the high values of insertion torques on the stress and strain distribution in cortical and cancellous bones. Based on tomography imaging, a representative mathematical model of a partial maxilla was built using Mimics 11.11 and Solid Works 2010 softwares. Six models were built and each of them received an implant with one of the following insertion torques: 30, 40, 50, 60, 70 or 80 Ncm on the external hexagon. The cortical and cancellous bones were considered anisotropic. The bone/implant interface was considered perfectly bonded. The numerical analysis was carried out using Ansys Workbench 10.0. The convergence of analysis (6%) drove the mesh refinement. Maximum principal stress (σ max) and maximum principal strain (ε max) were obtained for cortical and cancellous bones around to implant. Pearson's correlation test was used to determine the correlation between insertion torque and stress concentration in the periimplant bone tissue, considering the significance level at 5%. The increase in the insertion torque generated an increase in the σ max and ε max values for cortical and cancellous bone. The σmax was smaller for the cancellous bone, with greater stress variation among the insertion torques. The ε max was higher in the cancellous bone in comparison to the cortical bone. According to the methodology used and the limits of this study, it can be concluded that higher insertion torques increased tensile and compressive stress concentrations in the periimplant bone tissue.

Numerical assessment of mass conservation on a MAC-type method for viscoelastic free surface flows

A numerical study of mass conservation of MAC-type methods is presented, for viscoelastic free-surface flows. We use an implicit formulation which allows for greater time steps, and therefore time marching schemes for advecting the free surface marker particles have to be accurate in order to preserve the good mass conservation properties of this methodology. We then present an improvement by using a Runge-Kutta scheme coupled with a local linear extrapolation on the free surface. A thorough study of the viscoelastic impacting drop problem, for both Oldroyd-B and XPP fluid models, is presented, investigating the influence of timestep, grid spacing and other model parameters to the overall mass conservation of the method. Furthermore, an unsteady fountain flow is also simulated to illustrate the low mass conservation error obtained.

Comparison of different designs of implant-retained overdentures and fixed full-arch implant-supported prosthesis on stress distribution in edentulous mandible - A computed tomography-based three-dimensional finite element analysis

A finite element analysis was used to compare the effect of different designs of implant-retained overdentures and fixed full-arch implant-supported prosthesis on stress distribution in edentulous mandible. Four models of an human mandible were constructed. In the OR (O'ring) group, the mandible was restored with an overdenture retained by four unsplinted implants with O'ring attachment; in the BC (bar-clip) -C and BC groups, the mandibles were restored with overdentures retained by four splinted implants with bar-clip anchor associated or not with two distally placed cantilevers, respectively; in the FD (fixed denture) group, the mandible was restored with a fixed full-arch four-implant-supported prosthesis. Models were supported by the masticatory muscles and temporomandibular joints. A 100-N oblique load was applied on the left first molar. Von Mises (σvM), maximum (σmax) and minimum (σmin) principal stresses (in MPa) analyses were obtained. BC-C group exhibited the highest stress values (σvM=398.8, σmax=580.5 and σmin=-455.2) while FD group showed the lowest one (σvM=128.9, σmax=185.9 and σmin=-172.1). Within overdenture groups, the use of unsplinted implants reduced the stress level in the implant/prosthetic components (59.4% for σvM, 66.2% for σmax and 57.7% for σmin versus BC-C group) and supporting tissues (maximum stress reduction of 72% and 79.5% for σmax, and 15.7% and 85.7% for σmin on the cortical and trabecular bones, respectively). Cortical bone exhibited greater stress concentration than the trabecular bone for all groups. The use of fixed implant dentures and removable dentures retained by unsplinted implants to rehabilitate edentulous mandible reduced the stresses in the periimplant bone tissue, mucosa and implant/prosthetic components. © 2013 Elsevier Ltd.

A finite element approach for predicting the ultimate rotation capacity of RC beams

This paper presents a numerical approach to model the complex failure mechanisms that define the ultimate rotational capacity of reinforced concrete beams. The behavior in tension and compression is described by a constitutive damage model derived from a combination of two specific damage models [1]. The nonlinear behavior of the compressed region is treated by the compressive damage model based on the Drucker-Prager criterion written in terms of the effective stresses. The tensile damage model employs a failure criterion based on the strain energy associated with the positive part the effective stress tensor. This model is used to describe the behavior of very thin bands of strain localization, which are embedded in finite elements to represent multiple cracks that occur in the tensioned region [2]. The softening law establishes dissipation energy compatible with the fracture energy of the concrete. The reinforcing steel bars are modeled by truss elements with elastic-perfect plastic behavior. It is shown that the resulting approach is able to predict the different stages of the collapse mechanism of beams with distinct sizes and reinforcement ratios. The tensile damage model and the finite element embedded crack approach are able to describe the stiffness reduction due to concrete cracking in the tensile zone. The truss elements are able to reproduce the effects of steel yielding and, finally, the compressive damage model is able to describe the non-linear behavior of the compressive zone until the complete collapse of the beam due to crushing of concrete. The proposed approach is able to predict well the plastic rotation capacity of tested beams [3], including size-scale effects.

Simulação numérica do escoamento de jatos impingentes axissimétricos confinados

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Modelagem do escoamento e da transferência de calor ao longo de tubos capilares não adiabáticos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Simulação numérica de escoamentos incompressíveis pelo método de elementos finitos com esquema de Separação Baseado na Característica (CBS)

Pós-graduação em Engenharia Mecânica - FEIS

Modelagem da interação fluido-estrutura usando o método da fronteira imersa: aplicação ao estudo do escoamento em torno de um cilindro confinado

Pós-graduação em Engenharia Mecânica - FEIS

Modelagem numérica do escoamento em válvulas automáticas de compressores pelo Método da Fronteira Imersa

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Simulação numérica de escoamentos de fluidos com efeitos de rotação

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Simulação numérica de escoamentos de fluidos pelo método de elementos finitos baseado em volumes de controle em malhas não estruturadas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Reconstrução e geração de malhas em estruturas biomecânicas tridimensionais para análise por elemento finitos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Modelagem do escoamento transiente ao longo de trocadores de calor tubo capilar-linha de sucção

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Análise teórico-experimental de um tabuleiro misto madeira-concreto composto por vigas circulares

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análise numérica do comportamento não-linear de prismas de alvenaria estrutural submetidos a ações verticais utilizando o elemento finito prismático regular linear

Pós-graduação em Engenharia Civil - FEIS