Comparison of the GEANT4 releases 8.2 and 9.2 in terms of a pCT reduced calibration curve

The GEANT4 simulations are essential for the development of medical tomography with proton beams pCT. In the case of thin absorbers the latest releases of GEANT4 generate very similar final spectra which agree well with the results of other popular Monte Carlo codes like TRIM/SRIM, or MCNPX. For thick absorbers, however, the disagreements became evident. In a part, these disagreements are due to the known contradictions in the NIST PSTAR and SRIM reference data. Therefore, it is interesting to compare the GEANT4 results with each other, with experiment, and with diverse code results in a reduced form, which is free from this kind of doubts. In this work such comparison is done within the Reduced Calibration Curve concept elaborated for the proton beam tomography. © 2010 IEEE.

Sintering temperature influence on microwave dielectric properties of TiO2-ZrO2 ceramics

Dielectric ceramics have been widely investigated and used for microwave applications such as resonators and filters. The present study deals with the influence of sintering temperature on microwave dielectric properties of TiO2 ceramics with 10, 20, and 30 wt% ZrO2. Three compositions have been developed through mixing procedures and then tested for each sintering temperature: 1500 and 1400°C. X-ray diffraction and scanning electron microscopy are carried out aiming to explain the ceramic behavior of each sample. The dielectric constants of different ceramics for both temperatures varied from 85.4 to 62.6, while their quality factor due to dielectric losses varied from 3110 to 1630. The Q decrease is attributed to the non uniform grain growth and to the obtained crystalline phases. The best microwave parameters were obtained for the ceramics sintered at 1400°C, which can be applied in microwave circuits as dielectric resonators. © (2010) Trans Tech Publications.

Use of high energy ball milling on the sintering optimization of alumina ceramics

In this work, the effect of the milling time on the densification of the alumina ceramics with or without 5wt.%Y 2O 3, is evaluated, using high-energy ball milling. The milling was performed with different times of 0, 2, 5 or 10 hours. All powders, milled at different times, were characterized by X-Ray Diffraction presenting a reduction of the crystalline degree and crystallite size as function of the milling time increasing. The powders were compacted by cold uniaxial pressing and sintered at 1550°C-60min. Green density of the compacts presented an increasing as function of the milling time and sintered samples presented evolution on the densification as function of the reduction of the crystallite size of the milled powders. © (2010) Trans Tech Publications.

SnO 2 ceramics with low electrical resistivity obtained by microwave sintering

The main aim of this study was to develop dense and conducting SnO 2 ceramics without precipitated phases on the grain boundaries, which was verified using field emission scanning microscopy (FE-SEM) coupled with an energy-dispersive X-ray spectroscopy (FE-SEM/EDS). Two sample groups were investigated, where the first sample group was doped with zinc while the second one was doped with cobalt. The ceramics were prepared using the oxides mixture method and the sintering was carried out in a conventional muffle oven as well as in microwave oven. The results obtained were found to be similar regarding the relative density for the two sintering methods while time and temperature gains were observed for the microwave sintering method. The relative densities obtained were nearly 95%, for the two sintering methods. Concerning the electrical characterization measurements-electric field x current density as well as the environment temperature, the ceramics obtained through the conventional sintering method presented non-ohmic behavior. For the microwave sintered ceramics, we observed an ohmic behavior with electrical resistivity of 1.3 Ωcm for the samples doped with ZnO/Nb 2O 5 and 2.5 Ωcm for that of the samples doped with CoO/Nb 2O 5. The FE-SEM/EDS results for the microwave sintered ceramics indicated a structure with a reduced number of pores and other phases segregated at the grain boundaries, which leads to a better conductive ceramic than the conventional oven sintered samples. The dilatometry analysis determined the muffle sintering temperature and the difference between the densification of cobalt and zinc oxides. The addition of niobium oxide resulted in the decrease in resistivity, which thus led us to conclude that it is possible to obtain dense ceramics with low electrical resistivity based on SnO 2 using commercial oxides by the oxides mixture technique and the microwave oven sintering method. Copyright © 2011 American Scientific Publishers All rights reserved.

High-pressure assisted sintering of Ti-20Si-10B and Ti-10Si-5B powders

This work presents the structural characterization of Ti-10Si-5B and Ti-20Si-10B (at-%) alloys produced by high-pressure assisted sintering. Sintering was performed in air at 1100 and 1200°C for 60 s using pressure levels of 5 GPa. Structural evaluation of sintered samples was conducted by means of scanning electron microscopy and energy dispersive spectrometry. Samples were successfully consolidated after sintering, which presented theoretical density values higher than 99%. The microstructures of the sintered Ti-10Si-5B and Ti-20Si-10B alloys revealed the presence of the TiSS, TiB, TiB2, Ti5Si3, Ti5Si4, TiSi, and TiSi2.phases. A small amount of Ti6Si2B was formed after high-pressure assisted sintering of the Ti-20Si-10B alloy (5GPa, 1100°C for 60 s) indicating that equilibrium structures were not achieved during short sintering times. No oxygen and carbon contamination was detected in structures of Ti-Si-B alloys after high-pressure sintering at 1100 and 1200°C without controlled atmosphere. © (2012) Trans Tech Publications, Switzerland.

Social capital and culture: master keys to development

Includes bibliography

Sintering of porous alumina obtained by biotemplate fibers for low thermal conductivity applications

In this research report, a sintering process of porous ceramic materials based on Al2O3 was employed using a method where a cation precursor solution is embedded in an organic fibrous cotton matrix. For porous green bodies, the precursor solution and cotton were annealed at temperatures in the range of 100-1600°C using scanning electron microscopy (SEM) and thermogravimetric (TG) analysis to obtain a porous body formation and disposal process containing organic fibers and precursor solution. In a structure consisting of open pores and interconnected nanometric grains, despite the low porosity of around 40% (calculated geometrically), nitrogen physisorption determined a specific surface area of 14m2/g, which shows much sintering of porous bodies. Energy dispersive X-ray (EDX) and X-ray diffraction (XRD) analytical methods revealed a predominant amount of α-Al2O3 in the sintered samples. Thermal properties of the sintered Al2O3 fibers were obtained by using the Laser Flash which resulted in the lower thermal conductivity obtained by α-Al2O3 and therefore improved its potential use as an insulating material. © 2012 Elsevier Ltd.

Interval multivariate curve resolution in the dereplication of HPLC-DAD data from Jatropha gossypifolia

Introduction Jatropha gossypifolia has been used quite extensively by traditional medicine for the treatment of several diseases in South America and Africa. This medicinal plant has therapeutic potential as a phytomedicine and therefore the establishment of innovative analytical methods to characterise their active components is crucial to the future development of a quality product. Objective To enhance the chromatographic resolution of HPLC-UV-diode-array detector (DAD) experiments applying chemometric tools. Methods Crude leave extracts from J. gossypifolia were analysed by HPLC-DAD. A chromatographic band deconvolution method was designed and applied using interval multivariate curve resolution by alternating least squares (MCR-ALS). Results The MCR-ALS method allowed the deconvolution from up to 117% more bands, compared with the original HPLC-DAD experiments, even in regions where the UV spectra showed high similarity. The method assisted in the dereplication of three C-glycosylflavones isomers: vitexin/isovitexin, orientin/homorientin and schaftoside/isoschaftoside. Conclusion The MCR-ALS method is shown to be a powerful tool to solve problems of chromatographic band overlapping from complex mixtures such as natural crude samples. Copyright © 2013 John Wiley & Sons, Ltd. Extracts from J. gossypifolia were analyzed by HPLC-DAD and, dereplicated applying MCR-ALS. The method assisted in the detection of three C-glycosylflavones isomers: vitexin/isovitexin, orientin/homorientin and schaftoside/isoschaftoside. The application of MCR-ALS allowed solving problems of chromatographic band overlapping from complex mixtures such as natural crude samples. Copyright © 2013 John Wiley & Sons, Ltd.

Transformações estruturais em xerogéis de sílica tratados termicamente

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Utilização da curva de resfriamento na análise do refino de grão da liga AA 356

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Resistência à corrosão eletroquímica da liga TI-6AL4V prototipada para aplicações biomédicas

Pós-graduação em Engenharia Mecânica - FEIS

Avaliação da tenacidade à fratura na região de transição dúctil-frágil dos aços API 5L X70 e X80 utilizando a metodologia da curva mestra

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Growth curve of female collared peccaries (Pecari tajacu) raised in captivity in the Brazilian Amazon Region

Com o objetivo de ajustar modelos não-lineares, foram utilizados registros mensais do peso de 10 fêmeas de cateto (Pecari tajacu) coletados durante dois anos, no criatório do campo experimental Álvaro Adolfo da Embrapa Amazônia Oriental, Belém, PA. Utilizaram-se os modelos de Von Bertalanffy, Brody, Gompertz e Logístico. Os parâmetros foram estimados usando o procedimento NLIN do aplicativo SAS. Os critérios utilizados para verificar o ajuste dos modelos foram: desvio padrão assintótico (ASD); coeficiente de determinação (R²); desvio médio absoluto dos resíduos (ARD) e o índice assintótico (AR). Os modelos Brody e Logístico estimaram, respectivamente, o maior (19,44kg) e o menor (19,18kg) peso assintótico (A), caracterizando a menor (0,0064kg/dia) e a maior (0,0113kg/dia) taxa de maturação (K), haja vista a natureza antagônica entre estes parâmetros, comprovada pela correlação fenotípica variando entre -0,75 à -0,47. O modelo Brody estimou o menor valor para o ARD, fator limitante para caracterizar o menor valor para o AR por este modelo. Considerando o AR, o modelo Brody apresentou o melhor ajuste, contudo, pelos valores encontrados, os demais modelos também apresentaram ajuste adequando aos dados ponderais da referida espécie/sexo. Com base no AR adotado neste trabalho, recomenda-se o modelo Brody para ajustar a curva de crescimento de fêmeas de cateto (Pecari tajacu). Em razão dos valores estimados, sobretudo, para a K, essa característica pode ser incluída em um índice de seleção. Contudo, estudos com grupos mais representativos e criados em outras condições se faz oportuno.

Professional Master's degree in Nursing: knowledge production and challenges

OBJETIVO:analisar a produção do conhecimento gerada pelos programas de mestrado profissional em enfermagem e refletir sobre suas perspectivas para a área.MÉTODO:estudo descritivo e analítico. Foram incluídos dados das dissertações de três instituições de ensino que titularam alunos em programas de mestrado profissional em enfermagem entre 2006 e 2012.RESULTADOS:a maioria dos 127 trabalhos de conclusão analisados se desenvolveu no contexto hospitalar; houve tendência de concentração nas áreas organizacional e assistencial, nas linhas de pesquisa processo de cuidar e gerenciamento e predomínio de estudos qualitativos. Há diversidade de produtos resultantes dos trabalhos de conclusão: avaliação de serviços/programas de saúde e geração de processos, protocolos assistenciais ou de ensino.CONCLUSÃO:os programas de mestrado profissional em enfermagem, em fase de consolidação, têm produção recente, em desenvolvimento, havendo lacuna na geração de tecnologias duras e inovação. São fundamentais para o desenvolvimento das práticas profissionais inovadoras que articulem o setor saúde e a educação.