Seqüência Ordovício-Siluriana e Devoniana no Flanco Norte da Bacia do Paraná

Two stratigraphic sequences characterize the basal units of the Paraná basin. The Ordovician-Silurian sequence overlie directly the Neoproterozoic basement and consists of a 55m-thick unit of coarse-grained sandstones, diamictites, fossiliferous shales and fine-grained micaceous sandstones. The Alto Garças Formation constitutes the base of the sequence and is made of coarse-grained, massive and reddish sandstones associated with conglomeratic lenses. Diamictites with pebbles of diverse composition in siltic and arenaceous matrix were deposited during the Ordovician-Silurian glaciation. Whenever the basal sandstones are absent, the diamictites directly overlie the basement. The diamictites were previously included in the Vila Maria Formation. However our study revealed that they are part of the Iapó Formation. A transgressive event following the glaciation is marked by the deposition of the Vila Maria Formation, which is characterized by fossiliferous (mollusks, brachiopods, cryptospores and microplankton) and laminated shales and siltstones, grading upward to fine-grained micaceous sandstones with hummocky cross stratification. Layers containing trace fossils (Anthrophycus) occur at the transition between the siltstones and the sandstones. The Devonian sequence is represented by 80-170 meters thick sandstones of the Furnas Formation (lower unit) and a sucession of sandstones, siltstones and shales of the Ponta Grossa Formation (upper unit). Unlike other areas of the Paraná Basin, the Ponta Grossa Formation is characterized by coarsening-upward succession beginning with fine sandstones and grading upward to coarse and very-coarse sandstone beds. Cretaceous modifying tectonics affected the Paleozoic sequences, which are cut by a series of faults, in some cases showing displacements greater than 500 meters.

Aquatic macrophytes of Itaipu Reservoir, Brazil: Survey of species and ecological considerations

In a survey of the aquatic macrophytes of the Itaipu Reservoir, we identified 62 taxa in 25 families and 42 genera. The highest number taxa was observed for the emergent macrophytes (40 taxa). Reduced fluctuation in water level, increased light penetration, and sediment enrichment by nutrients and organic matter following the formation of the reservoir favored the appearance of a species-rich community of submerged macrophytes (23% of the taxa identified). The aquatic macrophytes were found mainly near the mouths of the main tributaries of the reservoir, in shallow area of depth less than 2 meters. In addition to the shallow depth, the greater nutrient input from the tributaries and relative protection from wind explained this distribution. Among the species found, Egeria najas merits mention for its occurrence in all localities sampled, with biomass values varying between 98 and 186 gDW/m2. Some potential nuisance species such as Eichhornia crassipes, Salvinia auriculata, and Pistia stratiotes also deserve attention, since they were also observed to be covering large areas of Itaipu Reservoir. © 1999, Paraná Institute of Technology Publication.

Posicionamento por ponto de alta precisão utilizando o GPS: Uma solução para a geodinâmica

Point positioning from GPS data can provide precision varying from 100 meters to a few millimeters at the level of 95% probability. To reach the best level of accuracy, users need proper equipment and software, as well as access capability to GPS products available at the International GPS Geodynamics Service. In this paper, the theory related to point positioning using GPS is presented as well as the results of an experiment conducted using data from the Brazilian Active Control System. The results show repeatability better than 5mm and 10mm for the N and E baseline components respectively, and 6mm + 4ppb (parts per billion) for the vertical. Comparison with SIRGAS campaign showed results at the same level of uncertainty as that of the stations used to tie the SIRGAS frame to ITRF94. Therefore, precise point positioning is a powerful tool to be used in applications requiring high level of precision, such as Geodynamics.

The use of shallow seismic reflection technique in near surface exploration of urban sites: An evaluation in the city of SãO Paulo, Brazil

In order to evaluate the use of shallow seismic technique to delineate geological and geotechnical features up to 40 meters depth in noisy urban areas covered with asphalt pavement, five survey lines were conducted in the metropolitan area of São Paulo City. The data were acquired using a 24-bit, 24-channel seismograph, 30 and 100 Hz geophones and a sledgehammer-plate system as seismic source. Seismic reflection data were recorded using a CMP (common mid point) acquisition method. The processing routine consisted of: prestack band-pass filtering (90-250 Hz); automatic gain control (AGC); muting (digital zeroin) of dead/noisy traces, ground roll, air-wave and refracted-wave; CMP sorting; velocity analyses; normal move-out corrections; residual static corrections; f-k filtering; CMP stacking. The near surface is geologically characterized by unconsolidated fill materials and Quaternary sediments with organic material overlying Tertiary sediments with the water table 2 to 5 m below the surface. The basement is composed of granite and gneiss. Reflections were observed from 40 milliseconds to 65 ms two-way traveltime and were related to the silt clay layer and fine sand layer contact of the Tertiary sediments and to the weathered basement. The CMP seismic-reflection technique has been shown to be useful for mapping the sedimentary layers and the bedrock of the São Paulo sedimentary basin for the purposes of shallow investigations related to engineering problems. In spite of the strong cultural noise observed in these urban areas and problems with planting geophones we verified that, with the proper equipment, field parameters and particularly great care in data collection and processing, we can overcome the adverse field conditions and to image reflections from layers as shallow as 20 meters.

Morphologic characterization and evaluation of the productivity of nine rootstocks of rose bush (rosa spp.)

In Brazil, garden and cut rose bushes are propagated through cuttings or grafting. The rootstocks used in most of the traditional areas of cultivation are not identified, being known just by the vulgar name. There is not any information in the literature on the morphologic characteristics, nor about the productivity of different cultivars on the rootstocks available in Brazil. The objective of this work was to characterize and determine productivity of nine rootstocks (Rosa multiflora 'Paulista'; R. multiflora 'Japones'; R. multiflora 'Iowa'; R. multiflora 'Kopmans'; R. indica 'Mayor'; R. indica x multiflora; R. sp. 'Natual Brier'; R. manetti and R. canina 'Inermis') grafted with 'Versilia' and 'Tineke' scions. Morphologic studies were undertaken to characterize branches of adult plants to determine shape and dimensions of the leaf; number of prickles/15 cm of stem; vigor of the stems; incidence of Diplocarpon rosae (blackspot) and coloration of the leaf. The productivity (number of commercial flowers/plant/month) was evaluated for 6 months (October, 2000 to March, 2001), in the city of Andradas, Minas Gerais State, located at 1251 meters above sea level. Since there was significant difference in just two months for both rootstocks, 'Tineke' and 'Versilia', no rootstocks could be considered inadequate. Nonetheless, in general, the rootstocks that showed a better performance with 'Tineke' were, R. multiflora 'Kopmans' and R. manetti and with 'Versilia', R. multiflora 'Kopmans' and Rosa sp. 'Natual Brier'.

Distribuição sazonal de parasitos branquiasis em diferentes especies de piexes em pesque-pague do municipio de Guariba-SP, Brasil.

This study was accomplished with the objective of knowing the seasonal distribution of the main species of parasites causes of branchial damages to the fish from fee-fishing at Guariba, State of São Paulo. This city is situated at 21 degrees 15'22'' S, 48 degrees 18'58'' W, in altitude 595 meters. This research was conducted between April, 1997 to March, 1999. From 408 fishes examined, 29.1% of them were infested by the protozoans e metazoans. Leporinus macrocephalus showed the highest parasitism by Trichodina sp., although Piaractus mesopotamicus and Cyprinus carpio were also parasited. Piscinoodinium pillulare infestation were found in L. macrocephalus, P. mesopotamicus, C. carpio e Colossoma macropomum. Monogenetics metazoan have largely been observed in L. macrocephalus, P. mesopotamicus, C. carpio, C. macropomum e cross-bred tambacu. The incidence of this parasite was elevated in the summer for L. macrocephalus, spring for P. mesopotamicus and C. macropomum, and both seasons for cross-bred tambacu. Lernaea cyprinacea copepodes were observed in L. macrocephalus, P. mesopotamicus, C. carpio and cross- breeding tambacu, in spite of the fact that C. carpio has demonstrated high parasitism of adult form. The fish L. macrocephalus, P. mesopotamicus and C. carpio were sponged intensely by Dolops carvalhoi, in situation of high population density. Piaractus mesopotamicus was considered the species more parasited by myxosporídeos, that were also observed in L. macrocephalus and cross-breeding tambacu.

Virtual instrumentation applied to the implementation of IEEE STD 1459-2000 power definitions

This paper discusses the utilization of Virtual Instrumentation to the implementation and evaluation of different power definitions, so that classical formulations and new definitions can be compared without the necessity of acquiring different power meters or analyzers. Accordingly, the definitions of IEEE Standard 1459-2000 for the measurement of power quantities under distorted and unbalanced situations, have been digitally implemented. Thus, several power and power factor components related to the decomposition of the measured voltage and current signals have been obtained. The proposed PC-based Virtual Instrument uses a high performance acquisition board and isolated sensors and transducers. All digital algorithms and routines have been implemented by means of a graphical development system. Regarding to the implementation of STD 1459, this paper also proposes several different algorithms to the required decompositions of voltage, current and power components. © 2005 IEEE.

Some considerations about a new procedure to derive transmission line parameters concerning three-phase lines

The paper shows an alternative methodology to calculate transmission line parameters per unit length and to apply it in a three-phase line with a vertical symmetry plane. This procedure is derived from a general procedure where the modal transformation matrix of the line is required. In this paper, the unknown modal transformation matrix requested by general procedure is substituted by Clarke's matrix. With the substitution that is shown in the paper, the transmission line parameters can be obtained starting from impedances measured in one terminal of the line. First, the article shows the classical methodology to calculate frequency dependent transmission line parameters by using Carson and Pollaczeck's equations for representing the ground effect and Bessel's functions to represent the skin effect. After that, a new procedure is shown to calculate frequency dependent transmission line parameters directly from currents and voltages of an existing line. Then, this procedure is applied in a non-transposed three-phase transmission line whose parameters have been previously calculated by using the classical methodology. Finally, the results obtained by using the new procedure and by using the classical methodology are compared. The article shows simulation results for typical frequency spectra of switching transients (10 Hz to 10 kHz). Results have shown that procedure has © 2006 IEEE.

Efeito do alumínio no conteúdo de poliaminas livres e atividade da fosfatase ácida durante o crescimento de brotações de Eucalyptus grandis × E. urophylla cultivadas in vitro

This paper is aiming to evaluate the effects of different levels of the aluminum on the growth of the Eucalyptus grandis x E. urophylla shoots cultivated in vitro. Evaluations were carried out on pH and chemicals modifications of the culture medium by Geochem program, polyamines contents (putrescine, espermidine e espermine) and acid phosphatase ativity on the shoots. The trial had a totally randomized design with four treatments and four replicates. The treatments were: 0.0, 6.75,13.50 and 27 mg.L -1 of AlCl 3.6H 2. Evaluations were carried out on the 4th, 8th, 12th, 16th, 20th, 24th and 28th day of culture. The addition of the aluminium, in all concentrations, affected the culture medium ionic equilibrium, the morphology of the shoots, reduced the pH on the medium, induced an increase in polyamines content and higher acid phosphatase activity.

Rod length influence in torque measurement of SPT-T test

Since Ranzini suggested supplementing the SPT test with measurement of the torque required to turn the split spoon sampler after driving, many Brazilian engineers have been using this in the design of pile foundations. This paper presents a study of the rod length influence in the torque measurement. A theoretical study of material resistance considering torsion and bending in a thin wall tubular steel shaft was performed. It makes possible to conclude that the shearing tension caused by the proper weight represents less than 1% of the shearing tension caused by the turning moment. In addition, an experimental study was done with electric torquemeters fixed in a horizontal rod system. The tests were being carried out to analyze rods of one meter to twenty meters in length and the measurements were collected at the ends of each rod length verifying the efficiency data. As a result, it is possible to verify that the torque difference through rod length is lower than minimum scales of mechanical torquemeters that are used on practical engineering. Also a fact to be considered is a big torque loss for values under 20 N.m of applied torque. This way, the SPT-T is not adequate to low consistency soil. Copyright ASCE 2007.

Orientation, building height and sky view factor as energy efficiency design parameters

The energy efficiency of buildings should be a goal at the pre-design phase, though the importance of the design variables is often neglected even during the design process. Highlighting the relevance of these design variables, this research studies the relationships of building location variables with the electrical energy consumption of residential units. The following building design parameters are considered: orientation, story height and sky view factor (SVF). The consideration of the SVF as a location variable contributes to the originality of this research. Data of electrical energy consumption and users' profiles were collected and several variables were considered for the development of an Artificial Neural Network model. This model allows the determination of the relative importance of each variable. The results show that the apartments' orientation is the most important design variable for the energy consumption, although the story height and the sky view factor play a fundamental role in that consumption too. We pointed out that building heights above twenty-four meters do not optimize the energy efficiency of the apartments and also that an increasing SVF can influence the energy consumption of an apartment according to their orientation.

Critical parameter determination of sonic flow controller diamond microtubes and micronozzles

In this article, the authors measure throughput of sonic diamond microtubes and micronozzles that can work as passive gas flow controllers and flow meters under choking conditions. The behavior of the outlet pressure through the microdevices using an experimental setup with constant volume and constant temperature was determined in order to obtain the critical throughput, the critical mass flow rate, and the discharge coefficients of the diamond sonic microdevices. © 2007 American Vacuum Society.

Modelagem numérica da superfície na geração da planialtimetra segundo dados de quatro equipamentos topogríficos

The aim of this present work was to compare planialtimetric charts obtained from different risings using two different theodolite types, a total station, and a precision level, used as control. Using a total station, an area was marked with clear variations of relief, following a grid, with a distance of 20 meters among stakes. After that, the stakes were read by the total station and two theodolites of different precisions. The geometric leveling was done by a precision level. The data were input in the DataGeosis software and the numerical modelling of the land was made with mesh of maximum rigidity, generating planialtimetric representation for each rising. It was verified, through comparison of the four representations that little variations occur in relation to the control. The closest representation of the control was the planialtimetry based on the data from the total station, in which the representations obtained from the theodolites were identical among themselves. It was concluded that in the process of obtaining detailed planialtimetry of small areas, submitted to the grid, it was not necessary to use composed geometric leveling, reducing work to the exclusive use of a total station or conventional theodolite.

Phytoplankton primary productivity in an urban eutrophic reservoir (São Paulo, Brazil)

The aim of this study was to analyze temporal ..d vertical variation of the biomass and of phytoplankton primary productivity in an urban eutrophic reservoir, in relation to the physical and chemical characteristics of the water. The physical and chemical variables of the water were defined in the limnetic region of the reservoir, at depths of 0.0; 0.5; 1.0; 2.0; 3.0 and 4.0 meters. Three samples were taken to define both the physical and chemical variables, concomitantly with the biomass (chlorophyll-a and phaeophytin) and phytoplankton primary productivity (C-14 method). Based on data obtained on differences in depth of the mixture zone and the euphotic zone, it is hypothesised that, depending on the time of the year, phytoplankton is conditioned by differences in the light and nutrient regimes, which change according to the constant loads of nutrients thrown into the system. The highest concentration of chlorophyll-a in the photic zone of the limnetic region was observed in November 2000 (1,197.3 mg Chl L -1) and the lowest in November 1999 (94.0 mg ChI L -1), whereas the profiles of primary activity of phytoplankton presented the highest rates on the surface of the water column, with values varying from 84.7 (May 2000) to 1,376.7mg C m -3 h -1 (December 2000). Annual primary productivity was calculated at 1,567.0gC m -2y -1, considered euproductive. The primary productivity profiles reported in this study are typical of aquatic eutrophic systems, rich in plankton and with low light penetration. It can be stated that Garças Lake is a system that suffers from anthropogenic impact, through receiving large loads of organic pollution, reflecting on the physical and chemical characteristics of the water and on the high values of biomass and primary phytoplankton activity. © National Institute of Ecology, New Delhi.

Theoretical and experimental evaluation of the influence of the length of drill rods in the SPT-T test

The influence of soil drill rod length on the N value in the SPT-T test has been studied extensively by Mello (1971), Schmertmann & Palacios (1979), Odebrecht et al. (2002) and Cavalcante (2002). This paper presents an analysis of the Standard Penetration Test supplemented with torque measurement (SPT-T). A theoretical study of the resistance of the rod material to torsion and bending indicated that the shear stress caused by the rod self-weight represents less than 1% of that caused by the torsional moment. An experimental study with electric torquemeters attached to a horizontal rod system, as well as two field tests in the vertical direction, were also carried out to compare and substantiate the results. The purpose of these tests was to analyze changes along the length of the rod in response to successive increments at 1-meter intervals. Torque measurements were taken at each increment of the length to ascertain the accuracy of the theoretical data. The difference between the applied torque and the measured torque at the end of rod system was lower than the minimum scale of mechanical torquemeters used in practice.