Growth and production performance of red tilapia and Nile tilapia (Oreochromis niloticus Lin.) under low-input culture system

Comparative production potential of red tilapia (a mutant hybrid of Oreochromis mossambicus) and Nile tilapia (Oreochromis niloticus) under low-input aquaculture was studied in six ponds of 360 m² each with an average water depth of 90 cm. Three ponds were stocked with fingerlings of O. niloticus (average weight 11.4±3.48 g) while three other ponds were stocked with red tilapia (average weight 10.72±2.5 g) at a density of 20,000 fingerlings/ha. Supplementary feed consisting of rice bran was given daily at 4-6% of standing biomass. Ponds were fertilized at fortnightly intervals with cattle manure 750 kg/ ha. After six months of rearing, gross fish productions of 3,218 and 3,017 kg/ha were obtained from O. niloticus and red tilapia ponds, respectively. Of this, table size fish (>80 g in size) production amounted to 2,366 and 2,823 kg/ha from O. niloticus and red tilapia culture, respectively. Analysis of cost and benefits showed higher benefit from red tilapia culture.

Recurrent input transformations for Hidden Markov models

This paper presents a new architecture which integrates recurrent input transformations (RIT) and continuous density HMMs. The basic HMM structure is extended to accommodate recurrent neural networks which transform the input observations before they enter the Gaussian output distributions associated with the states of the HMM. During training the parameters of both HMM and RIT are simultaneously optimized according to the Maximum Mutual Information (MMI) criterion. Results are presented for the E-set recognition task which demonstrate the ability of recurrent input transformations to exploit longer term correlations in the speech signal and to give improved discrimination.

Wavelength conversion based on an integrated semiconductor optical amplifier/DFB laser at 10 Gb/s with low input power

A study of the relative performance of an integrated semiconductor optical amplifier (SOA)/distributed feedback laser wavelength converter that can operate with negative penalties at 10 Gb/s rates is conducted. It is found that reduction of more than 25 times in required input powers are achieved when compared with laser or SOA converters.

1 × 4 space switching and simultaneous all-optical wavelength conversion at 2.488Gbit/s using a single monolithically integrated multiwavelength laser

A novel InGaAs/InGaAsP/InP integrated multiwavelength grating cavity laser is presented, which has been used to demonstrate space switching and simultaneous all-optical wavelength conversion at bit rates of 2.488 Gbit/s. This has been achieved using a single monolithically integrated device without the need for post-filtering to separate the converted signal from the input.

Nanostructuring of materials for device and sensor applications

The recent developments in nanotechnology are reviewed, with particular emphasis on its application in microsystem technology where increased reliability is achieved by integrating the sensor and the readout electronics on the same substrate. New applications may be possible using integrated micromechanical clips to connect optic fibers and components in integrated silicon systems. Some of the key developments in enabling technologies are also described, including the control of thin film deposition, nanostructuring to tailor the properties of thin film, silicon micromachining to make sensors, and microclips for the low-cost assembly of integrated optical microsystems.

10-Gbits/s all-optical 3R regeneration and format conversion using a gain-switched DFB laser

A strain-compensated multiple quantum well device is used as a DFB laser, this has been optimized for low jitter gain switched operation at 10 GHz. The signal is transmitted down 80 km of standard fiber then amplified, filtered and polarization controlled before being injected into a DFB laser. The purpose of this regeneration process is to gain switch the DFB with the extracted clock signal in order to retime the converted signal. This process also simultaneously converts the input NRZ format to an output RZ data to format and results in a signal whose optical power and extinction ratio are considerably improved by the regeneration process.

Tribological properties of mems materials measured on a small-scale device

Micro-electro-mechanical systems, MEMS, is a rapidly growing interdisciplinary technology within the general field of Micro-Systems Technology which deals with the design and manufacture of miniaturised machines with major dimensions at the scale of tens, to perhaps hundreds, of microns. Because they depend on the cube of a representative dimension, component masses and inertias rapidly become small as size decreases whereas surface and tribological effects, which often depend on area, become increasingly important. Although MEMS components and their areas of contact are small, tribological conditions, measured by contact pressures or acceptable wear rates, are demanding and technical and commercial success will require careful measurement and precise control of surface topography and properties. Fabrication of small numbers of MEMS devices designed to test potential material combinations can be prohibitively expensive and thus there is a need for small scale test facilities which mimic the contact conditions within a micro-machine without themselves requiring processing within a full semiconductor foundry. The talk will illustrate some initial experimental results from a small-scale experimental device which meets these requirements, examining in particular the performance of Diamond-Like-Carbon coatings on a silicon substrate. Copyright © 2005 by ASME.

A closely integrated digital image capture device for embedded applications

A modular image capture system with close integration to CCD cameras has been developed. The aim is to produce a system capable of integrating CCD sensor, image capture and image processing into a single compact unit. This close integration provides a direct mapping between CCD pixels and digital image pixels. The system has been interfaced to a digital signal processor board for the development and control of image processing tasks. These have included characterization and enhancement of noisy images from an intensified camera and measurement to subpixel resolutions. A highly compact form of the image capture system is in an advanced stage of development. This consists of a single FPGA device and a single VRAM providing a two chip image capturing system capable of being integrated into a CCD camera. A miniature compact PC has been developed using a novel modular interconnection technique, providing a processing unit in a three dimensional format highly suited to integration into a CCD camera unit. Work is under way to interface the compact capture system to the PC using this interconnection technique, combining CCD sensor, image capture and image processing into a single compact unit. ©2005 Copyright SPIE - The International Society for Optical Engineering.

Improved infrared thermal imaging of a CMOS MEMS device

We report a technique which can be used to improve the accuracy of infrared (IR) surface temperature measurements made on MEMS (Micro-Electro-Mechanical- Systems) devices. The technique was used to thermally characterize a SOI (Silicon-On-Insulator) CMOS (Complementary Metal Oxide Semiconductor) MEMS thermal flow sensor. Conventional IR temperature measurements made on the sensor were shown to give significant surface temperature errors, due to the optical transparency of the SiO 2 membrane layers and low emissivity/high reflectivity of the metal. By making IR measurements on radiative carbon micro-particles placed in isothermal contact with the device, the accuracy of the surface temperature measurement was significantly improved. © 2010 EDA Publishing/THERMINIC.

Voltage programmable dual-band bandpass/bandstop filter response in a single micro-electro-mechanical device

This paper reports on a switchable multi-band filter response achieved within a single micro-electro-mechanical device. A prototype device fabricated in a SOI process demonstrates a voltage programmable and tunable, dual-band, band-pass/band-stop response. Both analytical and finite element models are introduced in this paper to elucidate the operating principle of the filter and to guide filter design. Voltage programmability of the filter characteristic is demonstrated with the ability to independently tune the centre frequency and bandwidth for each band. A representative measurement shows that the minimum 3 dB-bandwidth (BW) is 155 Hz, 140Hz, and 20 dB-BW is 216 Hz, 203Hz for the upper-band and lower-band center frequencies located at 131.5 kHz and 130.7 kHz, respectively. © 2011 IEEE.

Input-output relationship and economics of pangas monoculture and carp-pangas polyculture in two districts of Bangladesh

An attempt was made to study the input-output relationships and economics of pangas monoculture and carp-pangas polyculture in Bangladesh. By analyzing the data collected from 50 pangas farms and 55 carp-pangas farms, the study has investigated the production systems of two technologies and the effects of fingerling stocking and applications of feed and fertilizer on fisheries income. The data were collected from the fishermen of Trishal and Bhaluka of Mymensingh district, and Kahaloo and Adamdighee of Bogra district during 2001-02. For pangas monoculture, the stocking density was 31,561 per ha while it was 55,017 per ha in carp-pangas polyculture. Most of the farmers used urea, TSP and lime before stocking. Rice and wheat bran happened to be the most common feed ingredients for both types of culture in general. Other important ingredients used were mustard oil-cakes, rice polish, wheat flour, fish meal, bone meal, soybean meal and poultry litter. In terms of quantities, rice bran and wheat bran dominated the farmers list. Rice and wheat bran together constituted about 60% of all studied feeds. Feed cost constituted 59.13% of total costs for pangas monoculture and 67.44% for carp-pangas polyculture. Per ha productions of pangas and carp-pangas in a single culture cycle were 15,508 kg and 19,745 kg, respectively. Per ha gross profits were estimated to be Tk 310,311 and Tk 464,418 for pangas monoculture and carp-pangas polyculture, respectively. Net profit appeared to be Tk 264,216 per ha for pangas monoculture and Tk 416,509 per ha for carp-pangas polyculture. The BCRs calculated were 1.46 and 1.68 for monoculture and polyculture, respectively. The break-even costs per kg of fish were estimated at Tk 36.93 for pangas and Tk 30.93 for mixed species which was much lower than the prices the producers received. Break-even productions were estimated at 10,702 kg per ha for pangas monoculture and 11,784 kg per ha for carp-pangas polyculture. Fingerling and feed cost, and pond size significantly explained the variation of income from pangas monoculture. These factors have significantly influenced the income from the crop. Functional analysis shows that 1% increase in the feed cost might increase 0.51% of pangas income and 0.41% in carp-pangas income. No other inputs had shown this much of responses to increasing income from a fish.