Inter-stage line ratio of He- and Li-like Ti emissions for the electron temperature measurement

Under coronal conditions, the steady state rate-equations are used to calculate the inter-stage line ratios between Li-like Is(2)2p(P-2(3/2))-> 1s(2)2s -> ((2) S-1/2) and He-like 1s2p (P-1(1))-> 1s(2) (S-1(0)) transitions for Ti in the electronic temperature ranges from 0.1 keV to 20 keV. The results show that the. temperature sensitivities are higher at the electronic temperature less than 5000 eV and the temperature sensitivities will decrease with the increase of electronic temperature.

Generation of 17-TW 23-fs pulses with a two-stage Ti : Sapphire amplifier at repetition rate 10 Hz

We have developed a two-stage Ti:sapphire amplifier system which can produce 17-TW/23-fs pulses at a repetition rate 10 MHz. A birefringent plate is used in the regenerative amplifier to alleviate gain narrowing, while an all-reflective cylindrical-mirror-based pulse stretcher and an acousto-optic programmable dispersive filter (AOPDF) are used to compensate for the higher order dispersion of the system.

Fast growing mode of stimulated Raman scattering in a pure three-wave process

Stimulated Raman scattering (SRS) of a relativistic laser in plasmas is studied in the framework of the standard equation set of a three-wave process. As far as every wave involved in the process is concerned, its evolution has two aspects: time-dependent amplitude and time-dependent frequency. These two aspects affect each other. Strict analysis and numerical experiment on the full three-wave equation set reveal that a fast growing mode of the instability, which could reach a balance or saturation point during a period far shorter than an estimation based on conventional analysis, could take place in a standard three-wave process without coupling with a fourth wave. This fast growing mode is found to stem from the constraint set by the background density on the amplitude of the driven Langmuir wave. The effect of various parameters on the development of the SRS instability is studied by numerical calculation of the history of the instability in different cases. (c) 2007 American Institute of Physics.

Ecological effects of trial pumpings in the Upper Lambourn: Stage 1 group pumping test Upper Lambourn group, September - November 1975

This report to the Thames Water Authority and Central Water Planning Unit is on research carried out in conjunction with the Stage 1 Group Pumping Test of five boreholes in the upper Lambourn Group for a period of three months in September, October and November 1975. The aim of the study was to assess the ecological effects of the pumpin g of five bore-holes in the upper Lambourn. That is, to determine how the seasonal sequence of ecological events in the river differed from what would hav e occurred had no pumping taken place. Since this 'experiment' has no control it is not possible to make a direct assessment. Nevertheless, by careful monitoring of ecological events before, during and after the pumping it is possible to document changes in th e river and by reference to the data already available for the Rive r Lambourn, normal seasonal changes in the flora and fauna can be separated from changes which may be attributable to the pumping and subsequent events.

The production of algae growing on gravel in a chalk-stream

Epilithic algae, ie that growing on the surface of stones, was studied as part of the work on the energy flow of the chalk-stream ecosystem, by the River Laboratory. The study area was on Bere Stream and 2 neighbouring streams. The algal biomass was estimated from analysis of chlorophyll a. In Bere Stream the peak chlorophyll a cover occurred in April, while in the neighbouring streams, which have considerably lower nutrient levels, there was on peak. Assuming that 2% of a diatoms dry wt is chlorophyll a, then even in mid-April the biomass of epilithic algae amounted to no more than 15 g dry wt m Super(-2) of exposed gravel. Annual production was calculated to be > 15 times greater than biomass. The estimation of net primary production is always difficult for benthic floras and comparisons are especially difficult when different methods are used. But these figures contrast sharply with those for Ranunculus (water crowfoot) which has a ratio of annual production to maximal seasonal biomass of 1:16. The accumulation of algal biomass is apparently being prevented. Some organic matter may be excreted; some algae will be washed off the bed of the stream by current and grazing by herbivorous invertebrates will also tend to prevent algal accumulation.

Aspects of the washout of salmonid eggs. 4. Effects of a standard mechanical shock, applied at different stage of development, upon survival and development of eggs of brown trout (Salmo trutta L.)

It is generally accepted by fish culturists that salmonid eggs are sensitive to mechanical shock and that the sensitivity varies with the stage of development of the eggs. In general, the period of greatest sensitivity is thought to occur between fertilization and ”eyeing”. However, it is reasonable to expect that, during a period (perhaps of several hours) following fertilization, sensitivity will be low because in nature during this period the eggs may be subject to some mechanical shock caused by the parent fish covering them with gravel. In 1983-4 and 1984-5 experiments were performed on brown trout (Salmo trutta L.) eggs to examine the effect of a standard mechanical shock (c. 2,500 eggs in 1983-4 and c. 8,400 eggs in 1984-5) at various stages of development upon survival to hatching and time of hatching.The results of these experiments are reported in this study.

In situ surface topography measurement method of granite base in scanning wafer stage with laser interferometer

Topography of a granite surface has an effect on the vertical positioning of a wafer stage in a lithographic tool, when the wafer stage moves on the granite. The inaccurate measurement of the topography results in a bad leveling and focusing performance. In this paper, an in situ method to measure the topography of a granite surface with high accuracy is present. In this method, a high-order polynomial is set up to express the topography of the granite surface. Two double-frequency laser interferometers are used to measure the tilts of the wafer stage in the X- and Y-directions. From the sampling tilts information, the coefficients of the high-order polynomial can be obtained by a special algorithm. Experiment results shows that the measurement reproducibility of the method is better than 10 nm. (c) 2006 Elsevier GmbH. All rights reserved.

Design and control of an ultraprecision stage used in grating tiling

In petawatt laser system, the gratings used to compose pulse compressor are very large in size which can be only acquired currently by arraying small aperture gratings to form a large one instead, an approach referred to as grating tiling. Theory and experiments have demonstrated that the coherent addition of multiple small gratings to form a larger grating is viable, the key technology of which is to control the relative position and orientation of each grating with high precision. According to the main factors that affect the performance of the grating tiling, a 5-DOF ultraprecision stage is developed for the grating tiling experiment. The mechanism is formed by serial structures. The motion of the mechanism is guided by flexure hinges and driven by piezoelectric actuators and the movement resolution of which can achieve nanometer level. To keep the stability of the mechanism, capacitive position sensors with nanometer accuracy are fixed on it to provide feedback signals with which to realize closed-loop control, thus the positioning precision of the mechanism is within several nanometers range through voltage control and digital PID algorithm. Results of experiments indicate that the performance of the mechanism can meet the requirement of precision for grating tiling.}

Valorization of scrap tires pyrolysis oil (STPO) through a 2-stage hydrotreating-hydrocracking strategy. Process variables and kinetic modeling

232 p.