The strength of column-to-foundation joints in reinforced concrete

This thesis is concerned with the experimental and theoretical investigation into the compression bond of column longitudinal reinforcement in the transference of axial load from a reinforced concrete column to a base. Experimental work includes twelve tests with square twisted bars and twenty four tests with ribbed bars. The effects of bar size, anchorage length in the base, plan area of the base, provision of bae tensile reinforcement, links around the column bars in the base, plan area of column and concrete compressive strength were investigated in the tests. The tests indicated that the strength of the compression anchorage of deformed reinforcing steel in the concrete was primarily dependent on the concrete strength and the resistance to bursting, which may be available within the anchorage . It was shown in the tests without concreted columns that due to a large containment over the bars in the foundation, failure occurred due to the breakdown of bond followed by the slip of the column bars along the anchorage length. The experimental work showed that the bar size , the stress in the bar, the anchorage length, provision of the transverse steel and the concrete compressive strength significantly affect the bond stress at failure. The ultimate bond stress decreases as the anchorage length is increased, while the ultimate bond stress increases with increasing each of the remainder parameters. Tests with concreted columns also indicated that a section of the column contributed to the bond length in the foundation by acting as an extra anchorage length. The theoretical work is based on the Mindlin equation( 3), an analytical method used in conjunction with finite difference calculus. The theory is used to plot the distribution of bond stress in the elastic and the elastic-plastic stage of behaviour. The theory is also used to plot the load-vertical displacement relationship of the column bars in the anchorage length, and also to determine the theoretical failure load of foundation. The theoretical solutions are in good agreement with the experimental results and the distribution of bond stress is shown to be significantly influenced by the bar stiffness factor K. A comparison of the experimental results with the current codes shows that the bond stresses currently used are low and in particular, CPIlO(56) specifies very conservative design bond stresses .

Shear induced toughening in bonded joints:experiments and analysis

Bonded joint specimens were fabricated from composite adherends and either an epoxy or a urethane adhesive. In mixed-mode fracture experiments, the epoxy bonded specimens generally failed by subinterfacial fracture in the composite, while specimens bonded with urethane failed very close to the adhesive/substrate interface. For the epoxy bonded specimens, fracture toughness did not change significantly with mode-mix, but for urethane bonded joints, fracture toughness increased with increasing shear load. Finite element analysis, which modeled specimens bonded with the two adhesives, showed similar trends. The different toughening behaviors for the two bonded joints can be attributed to dissipation of energy through inelastic deformation, which was insignificant in the epoxy-bonded joints but substantial when the urethane was used as the bonding agent.

Policy on the hoof:the handling of the foot and mouth disease outbreak in 2001

The foot and mouth disease (FMD) epidemic of 2001 was a disaster for sections of the agricultural industry, a number of businesses and for the Ministry of Agriculture, Fisheries and Food (MAFF), which met its demise as a government department during the crisis, being replaced by the Department of the Environment, Food and Rural Affairs (DEFRA). There were some 2,030 confirmed cases and over four million animals slaughtered. It caused the postponement of local elections and of a general election. From a public policy perspective it raised questions about contingency planning, the adjustment of policy to take account of change and how to manage a crisis. This article focuses on the background to the crisis and how it was handled.

Open Source Information Technologies Approach for Moddeling of Ankle-Foot Orthosis

Computer modeling is a perspective method for optimal design of prosthesis and orthoses. The study is oriented to develop modular ankle foot orthosis (MAFO) to assist the very frequently observed gait abnormalities relating the human ankle-foot complex using CAD modeling. The main goal is to assist the ankle- foot flexors and extensors during the gait cycle (stance and swing) using torsion spring. Utilizing 3D modeling and animating open source software (Blender 3D), it is possible to generate artificially different kind of normal and abnormal gaits and investigate and adjust the assistive modular spring driven ankle foot orthosis.

The blood perfusion and NADH/FAD content combined analysis in patients with diabetes foot

Skin blood microcirculation and the metabolism activity of tissue were examined on the patients with type 2 diabetes. Laser Doppler flowmetry (LDF) with 1064 nm laser light source and fluorescence spectroscopy (FS) with excitation light of 365 nm and 450 nm have been used to monitor the blood perfusion and the content of coenzymes NADH and FAD. Concluding, the proposed combined LDF and tissue FS approach allows to identify the significant violations in the blood microcirculation and metabolic activity for type 2 diabetes patients.

Desenvolvimento de um exoesqueleto para movimentação/reabilita-ção de paraplégicos

People bedridden by paralysis/motor disability are subject to several problems due to lack of movement. Then, it is necessary to use equipments that enable the people bedridden stand up and walk, so as to reduce the problems due to lack of movement and the time of rehabilitation, impacting directly on its quality of life. The aim of this work is the development of an exoskeleton to make the movement of people with paralysis / motor impairment in the lower limbs, without help of third parties, to be activated by the user. To provide support, stability and security to the deficient, it was decided to use a structure formed by four legs, being each leg consisting of a parallel chain. The gait was obtained by combining the movement of two mechanisms: crank/rocker, responsible for oscillatory motion of the leg, and cam/follower, responsible for the foot motion on the desired trajectory. To achieve the aim of this work was conducted a study about the types of exoskeletons for locomotion/rehabilitation of people with lower limb paralysis and presented a study on the movement of the lower limb joints. It also presented a mathematical model to obtain the desired path to the foot of the exoskeleton, the static model and the design of the structure elements. In the sequence is presented the simulation of movements of a people during the human gait, experimental tests and the comparison with the human gait developed by a people without disabilities.

Identification and classification of geometrical parameeters related to foot pathologies

Thèse numérisée par la Direction des bibliothèques de l'Université de Montréal.

Identification and classification of geometrical parameeters related to foot pathologies

Thèse numérisée par la Direction des bibliothèques de l'Université de Montréal.

Validating Scanned Foot Images and Designing Customized Insoles on the Cloud

People with foot problems need special healthcare: foot care. Customized insoles can provide this care. They are inserts that are placed in the shoes. They correct biomechanical and postural inaccuracies in foot. Insole production contains four phases: foot image scanning, image validation, insole design and insole manufacturing. Currently, image scanning and validation is separated in location and time, i.e. podiatrists take images and insole designers validate them at different location and at different time. A cloud-based solution, the CloudSME one-stop shop simulation platform, enables remote access to image validation and insole design service deployed and running on the Cloud. The remote access allows podiatrists validating scanned image while the patient is in their offices. The simulation platform also supports remote design of customized insoles.

Experimental Study of Interfacial Stress Distribution of Bonded-in BFRP Rod Glulam Joints Using Fibre Optic Sensors (FOS)

In this study, fibre optic sensors (FOS) were used to investigate the interfacial stress-strain behaviour of bonded-in basalt fibre reinforced polymer (BFRP) rods loaded into glulam members. Pull-out tests were conducted to examine the effect of bonded length and load-to-grain direction on the distribution of stress at the BFRP rod/adhesive zone. It was observed that the stress concentration at the loaded end of the BFRP rod of the samples was significantly the highest while the unloaded end showed the lowest. Increasing the bonded length at the same loading configuration resulted in a decrease in stress concentration at the loaded end. The stress concentration at the loaded end of the perpendicular to the grain samples was relatively higher than that of the corresponding parallel to the grain samples.

Improvement of Longitudinal Joints in Asphalt Pavement, HR-215, Construction Report, 1981

One significant benefit of asphalt concrete pavement construction is that it may be opened to traffic within one hour after being laid. Therefore, road closure and detour are not necessary, but only temporary lane closure and control of traffic. This one lane construction, even though desirable in regard to maintaining traffic flow, does pose an additional problem. The longitudinal joint at centerline often becomes a maintenance problem. The objective of this research project is to identify construction procedures that will provide an improved centerline joint.

Molecular Typing, Virulence Traits and Antimicrobial Resistance of Diabetic Foot Staphylococci

Diabetes mellitus is a major chronic disease that continues to increase significantly. One of the most important and costly complications of diabetes are foot infections that may be colonized by pathogenic and antimicrobial resistant bacteria, harboring several virulence factors, that could impair its successful treatment. Staphylococcus aureus is one of the most prevalent isolate in diabetic foot infections, together with aerobes and anaerobes.

Hybrid formulation solution for stress analysis of curved pipes with welded bending joints

A method is presented for evaluating the stress intensity factor of part-through cracks in a thin pipe elbow. A hybrid formulation solution is used to evaluate the stress field close to the crack area. The stress field values are then inputted into a previously developed method published in the literature to evaluate the stress intensity factor in cylindrical shells. Results from cylindrical shells with part-through cracks are extended to double-curvature pipe configurations that contain the same kind of flaw.