Fabrication of heterogeneous biocatalyst tethering artificial prosthetic groups to obtain omega-3-fatty acids by selective hydrolysis of fish oils

The active site of lipase from Bacillus thermocathenolatus was selectively modified with allyl and naphthyl chains at different positions. Lipase immobilization and selective tethering of a naphthyl side chain to its position 320 improve both the hydrolysis rate of fish oils and the selectivity towards the eicosapentaenoic acid acyl chains. © The Royal Society of Chemistry 2016.

Development, Evaluation and Optimization of Fabrication Processes for Daylight Guiding Systems Based on Micromirror Arrays

In this work, fabrication processes for daylight guiding systems based on micromirror arrays are developed, evaluated and optimized.Two different approaches are used: At first, nanoimprint lithography is used to fabricate large area micromirrors by means of Substrate Conformal Imprint Lithography (SCIL).Secondly,a new lithography technique is developed using a novel bi-layered photomask to fabricate large area micromirror arrays. The experimental results showing a reproducible stable process, high yield, and is consuming less material, time, cost and effort.

Étude comparative de deux méthodes de fabrication de yogourt grec à échelle pilote utilisant l’ultrafiltration comme technique de concentration - Étude basée sur la méthode d’Analyse de Cycle de Vie

Le yogourt grec, pouvant être obtenu par concentration du yogourt traditionnel par ultrafiltration (UF), connaît une croissance exceptionnelle en Amérique du Nord (+100% depuis 2012), et représente le premier segment de marché des produits laitiers fermentés en 2014. Cependant, d’un point de vue environnemental, la production du yogourt grec fait face à plusieurs enjeux et défis. Son élaboration nécessite trois fois plus de lait que le yogourt traditionnel de par l’étape de concentration nécessaire à l’atteinte de la concentration protéique cible. De plus, l’étape d’UF du yogourt génère un perméat acide (coproduit du yogourt) difficilement valorisable. Néanmoins, une alternative consistant à effectuer l’étape d’UF sur le lait avant sa fermentation permet d’éliminer la production du perméat acide, et génère un perméat de lactosérum doux déprotéiné dont les voies de valorisation sont davantage connues. Cette stratégie pourrait donc potentiellement réduire l’impact environnemental du procédé et générer des coproduits plus facilement valorisables, améliorant ainsi l’écoefficience du procédé de fabrication de yogourt grec. Dans cette optique, ce projet de recherche visait à comparer l’impact environnemental sur l’ensemble du cycle de vie de la production de yogourt grec selon deux procédés : en effectuant l’étape de concentration par UF avant l’étape de fermentation (UF LAIT), ou après (UF YOG) comme utilisé dans l’industrie. Ainsi, des expérimentations à échelle pilote ont été réalisées dans le but de comparer ces deux procédés. Le nouveau procédé (UF LAIT) permettrait une réduction des consommations d’énergie à l’étape de transformation étant donné que l’UF du lait avant fermentation permet de réduire la quantité de matière première à transformer d’environ un tiers. Cependant l’Analyse du Cycle de Vie (ACV) des deux procédés donne comme résultat un bilan environnemental défavorable à (UF LAIT) comparativement au procédé traditionnel (UF YOG) à cause d’une plus grande consommation de lait, qui est responsable d’environ 80% des impacts sur le cycle de vie du yogourt grec. Cet impact majeur pour UF LAIT l’est encore même lorsque dans une analyse de sensibilité le perméat doux de UF LAIT est alloué à l’étape d’UF contrairement au perméat acide de UF YOG qui est considéré comme un déchet non valorisable.

Utilisation d’arbres de faible vigueur provenant de forêts feuillues tempérées comme matière première pour la fabrication de granules de bois

La présente étude avait pour objectif de contribuer à une meilleure compréhension de la granulation des bois feuillus par l’évaluation de la possibilité technique de transformer des bois feuillus de faible vigueur (l’érable à sucre et le bouleau jaune) en granules conventionnels et granules de haute qualité, un type prometteur de transport énergétique. Trois études individuelles ont été réalisées et présentées dans cette thèse. La première étude visait à déterminer s’il y a des changements de teneur en extractibles, cendres, et lignine du bois entre les classes de vigueur des arbres. Les teneurs plus élevées en extractibles et en lignine dans les arbres peu vigoureux ont suggéré que ces derniers sont plus appropriés par rapport aux arbres vigoureux pour la conversion en biocombustibles solides. La deuxième étude visait à optimiser des procédés de granulation des bois feuillus. L’étude a porté sur l’influence des paramètres du procédé (la température et la force de compression) et des caractéristiques de la matière première (la taille des particules et la teneur en humidité) sur les propriétés physiques et mécaniques des granules de bois. Le procédé de granulation doit être effectué à une température d’environ 100 °C pour minimiser la force de friction dans le granulateur et à une teneur en humidité d’environ 11,2% pour maximiser la masse volumique et la résistance mécanique des granules produites. Cette étude a également confirmé que les arbres de faible qualité sont plus appropriés pour la fabrication de granules de bois que les arbres vigoureux. La troisième étude visait l’élaboration de granules de haute qualité. L’eau chaude à température élevée a été utilisée pour modifier les propriétés de la matière première avant granulation. Les caractéristiques de granulation du matériau traité ont été significativement améliorées. Les granules produites ont montré des propriétés améliorées incluant une plus faible teneur en cendres, une plus haute densité énergétique, une meilleure résistance à l’eau, et une meilleure résistance mécanique. Les résultats obtenus de toutes ces études ont démontré la nécessité de bien connaître les fondements de la granulation des bois feuillus et les solutions pratiques pour l’utilisation d’arbres feuillus de faible qualité, le premier peut être applicable pour le développement de procédés de granulation et le dernier peut contribuer à long terme à la restauration des forêts feuillues dégradées en termes de santé des forêts et de leur valeur.

Conception, fabrication et validation d'un banc d'essais pour la caractérisation de cellules photovoltaïques sur une large plage de température

L'énergie solaire est une source d'énergie renouvelable et naturellement disponible partout sur terre. Elle est donc tout indiquée pour remplacer à long terme une part importante des combustibles fossiles dans le portrait énergétique mondial. Comme toutes les formes d'énergie utilisées par la société, l'énergie solaire n'échappe pas aux lois économiques et son adoption dépend directement du coût par unité d'énergie produite. Plusieurs recherches et développements technologiques cherchent à réduire ce coût par différents moyens. Une de ces pistes est l'intégration de deux technologies solaires, la technologie photovoltaïque et la technologie thermique, au sein d'un même système. La conception d'un tel système pose plusieurs défis technologiques, le plus important étant sans contredit la compétition entre la quantité d'électricité produite et la qualité de la chaleur. En effet, ces deux variables varient de manière opposée par rapport à la température~: le rendement des cellules photovoltaïques a tendance à diminuer à haute température alors que la valeur utile de l'énergie thermique tend à augmenter. Une conception judicieuse d'un système photovoltaïque/thermique (PV/T) devra donc prendre en compte et connaître précisément le comportement d'une cellule à haute température. Le présent projet propose de concevoir un système permettant la caractérisation de cellules photovoltaïques sur une large plage de température. Premièrement, une revue de littérature pose les bases nécessaires à la compréhension des phénomènes à l'origine de la variation de la performance en fonction de la température. On expose également différents concepts de système PV/T et leur fonctionnement, renforçant ainsi la raison d'être du projet. Deuxièmement, une modélisation théorique d'une cellule photovoltaïque permet de définir grossièrement le comportement attendu à haute température et d'étudier l'importance relative de la variation du courant photogénéré et de la tension en circuit ouvert. Ce modèle sera plus tard comparé à des résultats expérimentaux. Troisièmement, un banc d'essais est conçu et fabriqué d'après une liste de critères et de besoins. Ce banc permet d'illuminer une cellule, de faire varier sa température de -20 °C à 200 °C et de mesurer la courbe I-V associée. Le système est partiellement contrôlé par un PC et la température est asservie par un contrôleur de type PID. Le banc a été conçu de manière à ce que la source de lumière soit aisément échangeable si un spectre différent est désiré. Finalement, le comportement du montage est validé en caractérisant une cellule au silicium et une autre à base de InGaP. Les résultats sont comparés aux prédictions du modèle et aux données de la littérature. Une étude d'incertitude permet également de cibler la source principale de bruit dans le système et propose des pistes d'améliorations à ce propos.

Fabrication and characterization of hybrid ferromagnetic-organic heterostructures for spintronics application

Recent research in the field of organic spintronics highlighted the peculiar spin-dependent properties of the interface formed by an organic semiconductor (OSC) chemisorbed over a 3d ferromagnetic metal, also known as spinterface. The hybridization between the molecular and metallic orbitals, typically π orbitals of the molecule and the d orbitals of the ferromagnet, give rise to spin dependent properties that were not expected by considering the single components of interfaces, as for example the appearance of a magnetic moment on non-magnetic molecules or changes in the magnetic behavior of the ferromagnet. From a technological viewpoint these aspects provide novel engineering schemes for spin memory and for spintronics devices, featuring unexpected interfacial magnetoresistance, spin-filtering effects and even modulated magnetic anisotropy. Applications of these concepts to devices require nevertheless to transfer the spinterface effects from an ideal interface to room temperature operating thin films. In this view, my work presents for the first time how spinterface effects can be obtained even at room temperature on polycrystalline ferromagnetic Co thin films interfaced with organic molecules. The considered molecules were commercial and widely used in the field of organic electronics: Fullerene (C60), Gallium Quinoline (Gaq3) and Sexithiophene (T6). An increase of coercivity, up to 100% at room temperature, has been obtained on the Co ultra-thin films by the deposition of an organic molecule. This effect is accompanied by a change of in-plane anisotropy that is molecule-dependent. Moreover the Spinterface effect is not limited to the interfacial layer, but it extends throughout the whole thickness of the ferromagnetic layer, posing new questions on the nature of the 3d metal-molecule interaction.

Fabrication of 2D and 3D microelectrode arrays for amperometric dopamine sensing: towards a metal free approach to bioelectronics

Dopamine is a neurotransmitter which has a role in several psychiatric and neurological disorders. In-vivo detection of its concentration at the microscopic scale would benefit the study of these conditions and help in the development of therapies. The ideal sensor would be biocompatible, able to probe concentrations in microscopic volumes and sensitive to the small physiological concentrations of this molecule (10 nM - 1 μM). The ease of oxidation of dopamine makes it possible to detect it by electrochemical methods. An additional requirement in this kind of experiments when run in water, though, is to have a large potential window inside which no redox reactions with water take place. A promising class of materials which are being explored is the one of pyrolyzed photoresists. Photoresists can be lithographically patterned with micrometric resolution and after pyrolysis leave a glassy carbon material which is conductive, biocompatible and has a large electrochemical water window. In this work I developed a fabrication procedure for microelectrode arrays with three dimensional electrodes, making the whole device using just a negative photoresist called SU8. Making 3D electrodes could be a way to enhance the sensitivity of the electrodes without occupying a bigger footprint on the device. I characterized the electrical, morphological, and electrochemical properties of these electrodes, in particular their sensitivity to dopamine. I also fabricated and tested a two dimensional device for comparison. The three dimensional devices fabricated showed inferior properties to their two dimensional counter parts. I found a possible explanation and suggested some ways in which the fabrication could be improved.

Fabrication by magnetron sputtering and characterization of electrodes based on CuIn0.7Ga0.3Se2 (CIGS)

This thesis work aims to produce and test multilayer electrodes for their use as photocathode in a PEC device. The electrode developed is based on CIGS, a I-III-VI2 semiconductor material composed of copper (Cu), indium (In), Gallium (Ga) and selenium (Se). It has a bandgap in the range of 1.0-2.4 eV and an absorption coefficient of about 105cm−1, which makes it a promising photocathode for PEC water splitting. The idea of our multilayer electrode is to deposit a thin layer of CdS on top of CIGS to form a solid-state p–n junction and lead to more efficient charge separation. In addition another thin layer of AZO (Aluminum doped zinc oxide) is deposit on top of CdS since it would form a better alignment between the AZO/CdS/CIGS interfaces, which would help to drive the charge transport further and minimize charge recombination. Finally, a TiO2 layer on top of the electrodes is used as protective layer during the H2 evolution. FTO (Fluorine doped tin oxide) and Molybdenum are used as back-contact. We used the technique of RF magnetron sputtering to deposit the thin layers of material. The structural characterization performed by XDR measurement confirm a polycrystalline chalcopyrite structural with a preferential orientation along the (112) direction for the CIGS. From linear fit of the Tauc plot, we get an energy gap of about 1.16 eV. In addition, from a four points measurements, we get a resistivity of 0.26 Ωcm. We performed an electrochemical characterization in cell of our electrodes. The results show that our samples have a good stability but produce a photocurrent of the order of μA, three orders of magnitude smaller than our targets. The EIS analysis confirm a significant depletion of the species in front of the electrode causing a lower conversion of the species and less current flows.

Design, fabrication and mechanical characterization of a structural node made using Wire and Arc Additive Manufacturing (WAAM) technology

Additive Manufacturing (AM), also known as “3D printing”, is a recent production technique that allows the creation of three-dimensional elements by depositing multiple layers of material. This technology is widely used in various industrial sectors, such as automotive, aerospace and aviation. With AM, it is possible to produce particularly complex elements for which traditional techniques cannot be used. These technologies are not yet widespread in the civil engineering sector, which is slowly changing thanks to the advantages of AM, such as the possibility of realizing elements without geometric restrictions, with less material usage and a higher efficiency, in particular employing Wire-and-Arc Additive Manufacturing (WAAM) technology. Buildings that benefit most from AM are all those structures designed using form-finding and free-form techniques. These include gridshells, where joints are the most critical and difficult elements to design, as the overall behaviour of the structure depends on them. It must also be considered that, during the design, the engineer must try to minimize the structure's own weight. Self-weight reductions can be achieved by Topological Optimization (TO) of the joint itself, which generates complex geometries that could not be made using traditional techniques. To sum up, weight reductions through TO combined with AM allow for several potential benefits, including economic ones. In this thesis, the roof of the British Museum is considered as a case study, analysing the gridshell structure of which a joint will be chosen to be designed and manufactured, using TO and WAAM techniques. Then, the designed joint will be studied in order to understand its structural behaviour in terms of stiffness and strength. Finally, a printing test will be performed to assess the production feasibility using WAAM technology. The computational design and fabrication stages were carried out at Technische Universität Braunschweig in Germany.

Microfluidic Paper-based Devices For Bioanalytical Applications.

Paper has become increasingly recognized as a very interesting substrate for the construction of microfluidic devices, with potential application in a variety of areas, including health diagnosis, environmental monitoring, immunoassays and food safety. The aim of this review is to present a short history of analytical systems constructed from paper, summarize the main advantages and disadvantages of fabrication techniques, exploit alternative methods of detection such as colorimetric, electrochemical, photoelectrochemical, chemiluminescence and electrochemiluminescence, as well as to take a closer look at the novel achievements in the field of bioanalysis published during the last 2 years. Finally, the future trends for production of such devices are discussed.

Rigidez do papelão ondulado: comparação entre resultados experimentais e os obtidos por cálculo analítico

Cardboard packing for horticultural products has as main function to protect them. The design of a cardboard packing request the knowledge of the bending stiffens which is depending on the modulus of elasticity. The objective of this work was to calculate the cardboard modulus of elasticity from data obtained in laboratory using physical characterization test, with different methods, and comparing the results with the values obtained experimentally. Ten samples of each cardboard selected for this study were tested in the paper fabrication direction and in its transverse direction. The papers liner and medium resistance to the traction, used to calculate the bending stiffness, was determined in a universal machine test. To obtaining of the bending stiffens the four points test was accomplished. Expressive variations among the methods from which the modulus of elasticity is obtained were observed and that influence the bending stiffness of the structure. The stiffness values obtained experimentally were always greater than the values obtained from analytical method. This difference can be attributed to two factors, the production processes that assurance a larger rigidity than the components separately and the addition of the adhesive layer that is not taken in consideration in the analytic calculations.

Evaluation of iris color stability in ocular prosthesis

Accurate iris reproduction in the fabrication of ocular prosthesis in order to match the remaining eye is a key factor to mask the loss and achieve an esthetic outcome for anophthalmic patients. This study evaluated the stability of acrylic paints used for replicating iris color in ocular prostheses by the analysis of two factors: the temperature of the acrylic resin polymerization cycle during prosthesis fabrication and the incidence of sun light, which is the main photodegrading agent undermining the longevity of ocular prostheses. An accelerated aging assay was used for both analyses. Specimens simulating the prosthetic iris in the colors blue, yellow, black, brown and green were fabricated, and were submitted to a colorimetric reading before and after undergoing the thermal conditions of acrylic resin polymerization. Next, the specimens were submitted to an artificial accelerated aging assay with ultraviolet radiation A and weekly colorimetric readings during a 3-week period. The color change (??*) values for the four specimens painted with the same color paint were averaged and the resulting values were considered for statistical analysis. Levine's test and Student's t-test were used to analyze the influence of the temperature of the polymerization cycle during prosthesis fabrication on the color stability of each acrylic resin paint. Friedman's test for three dependent samples was used for analysis of color photodegradation as function of time. Significance level was set at 0.05 for all analyses. It was observed that, after the action of the temperature of the polymerization cycle, alteration above clinically acceptable level of ??*> 3.3 was observed only for the yellow color. After the accelerated aging assay, there were statistically significant differences (p<0.05) as a function of time in the green, brown, black and blue colors. Changes were clinically acceptable for the brown and black colors; slightly above the clinically acceptable limit for the green color; and significantly high and impracticable from a clinical standpoint for the blue color. There was no statistically significant differences (p>0.05) for the yellow color, which presented color change only a little above the clinically acceptable limit. In conclusion: 1. Only the yellow color presented alterations above the clinically acceptable levels after the polymerization cycle; 2. After accelerated aging, there was no changes in the yellow color above the clinically acceptable levels; 3. For the green color, degradation was significant and slightly above the clinically acceptable levels; 4. The black, brown and blue colors presented significant alterations as function of time; the alterations of the brown and black colors were within acceptable clinical levels, while the blue color presented a more accentuated degradation over time.

Métodos para fabricação de microeletrodos visando a detecção em microambientes

Analysis at microenvironments, like single cells or in minute volumes (nL), is an area of great interest for analytical and biological sciences. Measurements at these experimental conditions demand analytical tools (microelectrodes) capable of monitoring with rapid response, good resolution and minimal perturbation of the system. The major drawbacks in producing these microscopic electrodes have been largely overcome, principally due to the development of new fabrication methods. In this review, these procedures are described with emphasis to those devoted to the construction of microelectrodes for application in microenvironments. Examples of our efforts to use these devices as effective electrochemical sensors are also addressed.

A novel disposable electrochemical microcell: construction and characterization

An alternative technique for the fabrication of disposable electrochemical microcells containing working, reference and auxiliary electrodes on a single device is reported. The procedure is based on thermal-transfer of toner masks onto CD-R (recordable compact discs) gold surfaces to define the layout of the electrodes (contour). In a subsequent step, the layout is manually painted with a permanent marker pen. The unprotected gold surface is conveniently etched (chemical corrosion) and the ink is then easily removed with ethanol, generating gold surfaces without contamination. The final and reproducible area of the electrodes is defined by heat transference of a second toner mask. Silver epoxy is deposited on one of the gold bands which is the satisfactorily used as reference electrode. These microcells were electrochemically characterized by cyclic, linear, and square wave voltammetry, and several electroactive species were used as model systems. The area reproducibility of the electrodes for different microcells was studied and a relative standard deviation better than 1,0% (n = 10) was obtained. Disposable electrochemical microcells were successfully used in analysis of liquid samples with volumes lower than 200 µL and good stability and reproducibility (RSD less than 2.0%) were achieved. These microcells were also evaluated for quantification of paracetamol and dipyrone in pharmaceutical formulations.