Influência da utilização do fluido de corte com adição de grafeno na temperatura de usinagem e formação de rebarba no processo de micro fresamento

As time passed, humanity needed the development of new materials used in various activities. High strength materials such as titanium and Inconel for example, had been studied because they are widely used for implants in biomedicine, as well as their use in aerospace and automotive industries. Because of its thermal and mechanical properties, these materials are considered difficult to machine, promoting a rapid wear of cutting tools, primarily caused by the high temperatures in machining. With the development of new materials has emerged the need of developing new manufacturing processes. One of today’s innovative processes is the micro-manufacturing. Being a process with a defined cutting tool geometry, burr formation is a constant and undesirable phenomenon formed during the machininig process. Being detrimental to the manufacturing process, overspending deburring operations are constantly employed leading to increase the aggregate cost to the manufactured material. Assembly components are also impaired if there is no control of the burr, with consequences including the disposal of components due to the occurence of this phenomenon. This paper presents the study of micro-milling Inconel 718, investigating influential parameters in the formation of burrs in order to minimize the occurrence of this phenome non. Different feed rates per tooth and cutting speed are evaluated, and different cutting fluids with different methods of applying the fluid. Adding graphene to cutting fluids was considered as a variable to be investigated, which is considered an excellent solid lubricant, in addition to increasing the thermal conductivity of the cooling solution (AZIMI; MOZAF FARI, 2015). The micro-milling temperature was evaluated in the present work. It was observed a new phenomenon that causes the machined surface temperature decreases below room temperature when using the solution water + oil. This phenomenon is explained in further chapters. In order to unravel this phenomenon, a new test was proposed and, from this test, it can be concluded, comparatively, which cutting fluid has a better cooling property.Using cutting fluid with different thermal properties has shown influence when analy zing burr formation and reducing machining temperature.

Avaliação tribológica de novas modificações superficiais para cilindros de laminação a frio

The present work analyzed the tribological behavior of coatings/surface modifications traditionally used in cold rolling mill rolls and new coatings/surface modificationswith potential to replace the carcinogenic hard chrome. The study started with identification of wear mechanisms occurring in real coldrollingmill rolls. Due the high cost and dimensions of the rolls, thereplication technique was used. Replicas were obtained from 4 different rolling millBrazilian companies before and after a normal rolling campaign. Initial sliding tests were conducted using spherical and cylindrical counter bodies in order to verifywhichtribological conditions allowed to reproduce the wear mechanisms found in the replicas. These tests indicated the use of reciprocating sliding tests with cylindrical counter bodies (line contact), normal load of 100 N, and test times of and 1 h and 5 h. Different surface modifications were carried out on samples produced from a fragment of a rolling mill roll. The specimens were heat treated and ground on both sides. After, some specimens were surface textured by electrical discharge texturing (EDT). For both groups (ground and EDT), subsequent treatments of chromium plating, electroless NiP coating and plasma nitriding were carried out. The results of the reciprocating tests showed that specimens with electroless NiP coating presented the lowest friction coefficients, while plasma nitrided specimens showed the highest. In general, previous surface texturing before the coating/surface modification increased the wear of the counter bodies. Oneexceptionwas for EDT with subsequent electroless NiP coating, which presented the lowest counter bodies wear rate. The samples withelectroless NiP coating promoted a tribolayer consisting of Nickel, Phosphorus and Oxygen on both the specimens andthecounter bodies, which was apparently responsible for the reduction of friction coefficient and wear rate. The increase of the test time reduced the wear rate of the samples, apparently due the stability of the tribolayers formed, except for the nitrided samples. For the textured specimens, NiP coating showed the best performance in maintaining the surface topography of the specimens after the sliding tests.

Avaliação da soldagem GMAW mecanizada e automatizada para união de dutos utilizando fontes convencional e com controle de curto- circuito

Welding is one of the most employed process for joining steel pipes. Although, manual welding is still the most used one, mechanized version and even automatized one have increased its demand. Thus, this work deals with girth welding of API 5L X65 pipes with 8” of nominal diameter and 8.0 mm thickness, beveled with V-30º narrow gap. Torch is moved by a bug carrier (mechanized welding) and further the parameters are controlled as a function of angular position (automatized welding). Welding parameters are presented for filling the joint with two-passes (root and filling/capping passes). Parameters for the root pass were extracted from previous author´s work with weldments carried out in plates, but validated in this work for pipe welding. GMAW processes were assessed with short-circuit metal transfer in both conventional and derivative modes using different technologies (RMD, STT and CMT). After the parameter determination, mechanical testing was performed for welding qualification (uniaxial tension, face and root bending, nick break, Charpy V-notch impact, microhardness and macrograph). The initially obtained results for RMD and CMT were acceptable for all testing and, in a second moment, also for the STT. However, weld beads carried out by using the conventional process failed and revealed the existence of lack of fusion, which required further parametrization. Thus, a Parameter-Variation System for Girth Welding (SVP) was designed and built to allow varying the welding parameters as a function of angular position by using an inclinometer. The parameters were set for each of the three angular positions (flat, vertical downhill and overhead). By using such equipment and approach, the conventional process with parameter variation allowed reducing the welding time for joint accomplishment of the order of 38% for the root pass and 30% for the filling/capping pass.

Retificação plana tangencial dos ferros fundidos nodular, vermicular e cinzento em várias condições de corte

In a scenario of increasing competitiveness of the global industrial sector and with a consumer market increasingly demanding, there is an increased demand for new materials and, consequently, possibilities to explore new research and technological advances towards the development of new manufacturing methods or the improvement of existing technologies. In the case of cast irons, new grades of them have been developed so that their mechanical properties have been improved, making them more competitive with steel, expanding the applications and thus represents great economic gain for metallurgy and manufacturing sectors. This increases the interest and creates new opportunities to study these materials and identify how they respond in terms of the surface integrity, tool wear, cutting forces, among others, when machined by grinding operation. In this context, due to the lack of results from grinding of cast irons and studies comparing grindability among several grades of cast irons found in the literature, this work aims to generate scientific and technological contribution to the metallurgical and metal working sector through roughness results (Ra and Rz parameters) and evaluation and analysis of the subsurface integrity of three cast iron grades (gray, compacted graphite and nodular). The machining trials were performed on a surface grinding machine with silicon carbide grinding wheel at different cutting conditions. The input variables were the radial depth of cut (15 and 30 μm), worktable speed, vw (5 and 10 m/min) and the abrasive grain size of the grinding wheel. The results showed that surface roughness increased with the radial depth of cut for all materials tested; and the lowest values were obtained for gray cast iron. Also, roughness was sensitive to variation of worktable speed and the lowest values were obtained after machining with vw = 5 m/min. With respect to the abrasive grain size, as it decreased the roughness values increased to gray and nodular cast iron grades. Furthermore, grinding burns marks were observed on the surfaces of nodular cast iron and compacted graphite iron grades after grinding the smallest grain size, contrary to what is usually reported in literature. However, no evidence of severe thermal damages below the machined surfaces of all cast iron grades was observed after analyzing the results of hardness and the SEM micrograph images.

Desenvolvimento de um exoesqueleto para movimentação/reabilita-ção de paraplégicos

People bedridden by paralysis/motor disability are subject to several problems due to lack of movement. Then, it is necessary to use equipments that enable the people bedridden stand up and walk, so as to reduce the problems due to lack of movement and the time of rehabilitation, impacting directly on its quality of life. The aim of this work is the development of an exoskeleton to make the movement of people with paralysis / motor impairment in the lower limbs, without help of third parties, to be activated by the user. To provide support, stability and security to the deficient, it was decided to use a structure formed by four legs, being each leg consisting of a parallel chain. The gait was obtained by combining the movement of two mechanisms: crank/rocker, responsible for oscillatory motion of the leg, and cam/follower, responsible for the foot motion on the desired trajectory. To achieve the aim of this work was conducted a study about the types of exoskeletons for locomotion/rehabilitation of people with lower limb paralysis and presented a study on the movement of the lower limb joints. It also presented a mathematical model to obtain the desired path to the foot of the exoskeleton, the static model and the design of the structure elements. In the sequence is presented the simulation of movements of a people during the human gait, experimental tests and the comparison with the human gait developed by a people without disabilities.

Metal transfer mapping for FCAW process by using near-infrared filming

In the Flux Cored Arc Welding (FCAW) process, the transfer of filler metal (metal transfer modes) to the base material to accomplish the weld bead determines the weld quality and therefore studies of such phenomena is demanded. Thus, in this work, the metal transfer through the FCAW process is investigated by filming the phenomena with the assist of near infrared visualization. During the literature survey, it was found that this technic has not been used so far for analyzing the FCAW process. It must be pointed out that the radiation emitted from the weld arc, fumes and particles (spattering) in this process represent a barrier for these studies based in the process visualization. The monitoring of metal transfer for FCAW process was carried out within the operational envelope of voltage and wire feed speed with the electrode E71T-1 (1.2 mm diameter) and Ar+25%CO2 as a shielding gas. A local developed near infrared filming with frame rate of 300 Hz was employed for metal transfer visualization in order to contribute to a better understanding of this process and evaluating characteristics of metal transfer, unlike previous studies, which used shadowgraph technique. It can clearly be seen how the droplet is created and transferred in this process and also identify the different modes of metal transfer by changing the parameters of voltage and wire feed speed in metal transfer maps. The final result of this study is the metal transfer mode maps, which establish suitable conditions and provide the basis for developing arc control strategies for the FCAW process.

Avaliação da incerteza de medição no Setor Médico-hospitalar

This study aims to evaluate the uncertainty associated with measurements made by aneroid sphygmomanometer, neonatal electronic balance and electrocautery. Therefore, were performing repeatability tests on all devices for the subsequent execution of normality tests using Shapiro-Wilk; identification of influencing factors that affect the measurement result of each measurement; proposition of mathematical models to calculate the measurement uncertainty associated with measuring evaluated for all equipament and calibration for neonatal electronic balance; evaluation of the measurement uncertainty; and development of a computer program in Java language to systematize the calibration uncertainty of estimates and measurement uncertainty. It was proposed and carried out 23 factorial design for aneroid sphygmomanometer order to investigate the effect of temperature factors, patient and operator and another 32 planning for electrocautery, where it investigated the effects of temperature factors and output electrical power. The expanded uncertainty associated with the measurement of blood pressure significantly reduced the extent of the patient classification tracks. In turn, the expanded uncertainty associated with the mass measurement with neonatal balance indicated a variation of about 1% in the dosage of medication to neonates. Analysis of variance (ANOVA) and the Turkey test indicated significant and indirectly proportional effects of temperature factor in cutting power values and clotting indicated by electrocautery and no significant effect of factors investigated for aneroid sphygmomanometer.

A influência do amortecimento viscoelástico na estabilidade aeroelástica de painéis aeronáuticos

Since the creation of supersonic vehicles, during the Second World War, the engineers have given special attention to the interaction between the aerodynamic efforts and the structures of the aircrafts due to a highly destructive phenomenon called flutter in aeronautical panel. Flutter in aeronautical panels is a self-excited aeroelastic phenomenon, which can occurs during supersonic flights due to dynamic instability of inertia, elastic and aerodynamic forces of the system. In the flutter condition, when the critical aerodynamic pressure is reached, the vibration amplitudes of the panel become dynamically unstable and increase exponentially with time, affecting significantly the fatigue life of the existing aeronautical components. Thus, in this paper, the interest is to investigate the possibility of reducing the effects of the supersonic aeroelastic instability of rectangular plates by applying passive constrained viscoelastic layers. The rationale for such study is the fact that as the addition of viscoelastic materials provides decreased vibration amplitudes it becomes important to quantify the suppression of plate flutter coalescence modes that can be obtained. Moreover, despite the fact that much research on the suppression of panel flutter has been carried out by using passive, semi-active and active control techniques, very few of them are adapted to deal with the problem of estimating the flutter speeds of viscoelastic systems, since they must conveniently account for the frequency- and temperature-dependent behavior of the viscoelastic material. In this context, two different model of viscoelastic material are developed and applied to the model of sandwich plate by using finite elements. After the presentation of the theoretical foundations of the methodology, the description of a numerical study on the flutter analysis of a three-layer sandwich plate is addressed.

Investigação experimental das propriedades termofísicas e da convecção forçada de nanofluido de grafeno

This work presents an experimental investigation of thermal hydraulic performance of the nanofluid composed by graphene nanoparticles dispersed in a mixture of water and ethylene glycol at a ratio of 70:30% by volume. The tests were carried out under forced convection inside a circular tube with uniform heat flux on the wall for the laminar-turbulent transition regime. The mass flow rate ranged from 40 to 70 g/s corresponding to Reynolds numbers between 3000 and 7500. The heat flux was maintained constant at values of 11, 16 and 21 kW/m², as well as the inlet temperature of 15, 20 and 25°C. Three samples were produced with the nanofluid volumetric concentration of 0.05%, 0.10% and 0.15%. Thermophysical properties were experimentaly measured for all samples that were critically compared and discussed with theoretical models most commonly used in the literature. Initially, experiments with distilled water confirmed the validity of the experimental equipment for the thermo-hydraulic tests. Therefore, nanofluid samples that showed the highest thermal conductivity, corresponding to the volumetric concentrations of 0.15% and 0.10%, were subjected to the tests. The thermal-hydraulic performance for both samples was unsatisfactory. The heat transfer coefficients for convection of nanofluids reduced 21% in average, for the sample with = 0.15% and 26% and for =0.10%. The pressure drop of the samples was higher than the base fluid. Finally, the pressure drop and heat transfer coefficient by convection of both samples were also compared to theoretical models. The models used for pressure drop showed an excellent agreement with experimental results, which is remarkable considering the transitional flow.

O Litoral e a metrópole dinâmica imobiliária, turismo e expansão urbana na região metropolitana de Natal-RN

The metropolitan regions of Northeast Brazil are being gradually included in a scenario of international investments, which are motivated by the restructuring of both touristic and real-estate sectors. The new capital, real-estate developers and space configurations that result from this process indicate the need for the creation and implementation of public tools which should, at least, allow the mitigation of the urban impacts and environmental losses resulting from this situation. The effects on landscape and on the socio-spatial configuration result from the intensification caused by the dynamism of the "real estate-tourism" sector. There is a regional integration as an expression of the urban expansion of the metropolitan area of Natal. This study investigates the uniqueness of the restructuring and territorial integration of coastal areas and the strategies of the circuit of capital accumulation formed by linking the real estate to tourism. It is intended to increase the understanding about the strategies of tourism, real estate and public policy agents involved in this territorial reconfiguration and in the fund-raising needed for the investments, to understand the existing social and environmental effects and their future trends and also to understand the forms of spatial production as results from the practices of approaching the land transformation and the tourism valorization of the landscape, in a synchronous manner, first in the Northeast region and, as a focal study, in the Metropolitan Area of Natal. Likewise, it is intended to apprehend the current processes of metropolization of the eastern coast of Rio Grande do Norte, in addition to indicate its physical-territorial transformation and the types of projects/developments promoted by the market in the recent period. Based upon analysis undertaken for the Metropolitan Region of Natal RN, this piece of work presents some considerations on possible legal instruments that can be adjusted to the municipalities which are experiencing the impact of this peculiar and recent phenomenon in the region, caused by the arrival of the real estate-touristic capital. It is also intended to point out basic proposals to the forms of public intervention, in a speculative way, starting from a Metropolitan Planning project within a medium and long term

Aplicação da metodologia numérica “fast bounds crack” para uma estimativa eficiente da evolução do tamanho de trinca

A significant part of the life of a mechanical component occurs, the crack propagation stage in fatigue. Currently, it is had several mathematical models to describe the crack growth behavior. These models are classified into two categories in terms of stress range amplitude: constant and variable. In general, these propagation models are formulated as an initial value problem, and from this, the evolution curve of the crack is obtained by applying a numerical method. This dissertation presented the application of the methodology "Fast Bounds Crack" for the establishment of upper and lower bounds functions for model evolution of crack size. The performance of this methodology was evaluated by the relative deviation and computational times, in relation to approximate numerical solutions obtained by the Runge-Kutta method of 4th explicit order (RK4). Has been reached a maximum relative deviation of 5.92% and the computational time was, for examples solved, 130,000 times more higher than achieved by the method RK4. Was performed yet an Engineering application in order to obtain an approximate numerical solution, from the arithmetic mean of the upper and lower bounds obtained in the methodology applied in this work, when you don’t know the law of evolution. The maximum relative error found in this application was 2.08% which proves the efficiency of the methodology "Fast Bounds Crack".

Análise e modelagem do escoamento transitório de fluidos de perfuração

Drilling fluids present a thixotropic behavior and they usually gel when at rest. The sol-gel transition is fundamental to prevent the deposit of rock fragments, generated by drilling the well, over the drill bit during eventual stops. Under those conditions, high pressures are then required in order to break-up the gel when circulation is resumed. Moreover, very high pressures can damage the rock formation at the bottom of the well. Thus, a better understanding of thixotropy and the behavior of thixotropic materials becomes increasingly important for process control. The mechanisms that control thixotropy are not yet well defined and modeling is still a challenge. The objective of this work is to develop a mathematical model to study the pressure transmission in drilling fluids. This work presents a review of thixotropy and of different mathematical models found in the literature that are used to predict such characteristic. It also shows a review of transient flows of compressible fluids. The problem is modeled as the flow between the drillpipe and the annular region (space between the wall and the external part of the drillpipe). The equations that describe the problem (mass conservation, momentum balance, constitutive and state) are then discretized and numerically solved by using a computational algorithm in Fortran. The model is validated with experimental and numerical data obtained from the literature. Comparisons between experimental data obtained from Petrobras and calculated by three viscoplastic and one pseudoplastic models are conducted. The viscoplastic fluids, due to the yield stress, do not fully transmit the pressure to the outlet of the annular space. Sensibility analyses are then conducted in order to evaluate the thixotropic effect in pressure transmission.

Acreditação do Laboratório de Metrologia da Frilabo para Ensaios e Calibrações em Temperaturas

O trabalho desenvolvido centrou-se na preparação da acreditação NP EN ISO/IEC 17025 do Laboratório de Metrologia da empresa Frilabo para prestação de serviços na área das temperaturas, no ensaio a câmaras térmicas e na calibração de termómetros industriais. Considerando o âmbito do trabalho desenvolvido, são abordados nesta tese conceitos teóricos sobre temperatura e incertezas bem como considerações técnicas de medição da temperatura e cálculo de incertezas. São também referidas considerações sobre os diferentes tipos de câmaras térmicas e termómetros. O texto apresenta os documentos elaborados pelo autor sobre os procedimentos de ensaio a câmaras térmicas e respetivo procedimento de cálculo da incerteza. Também estão presentes neste texto documentos elaborados pelo autor sobre os procedimentos de calibração de termómetros industriais e respetivo procedimento de cálculo da incerteza. Relativamente aos ensaios a câmara térmicas e calibração de termómetros o autor elaborou os fluxogramas sobre a metodologia da medição da temperatura nos ensaios, a metodologia de medição da temperatura nas calibrações, e respetivos cálculos de incertezas. Nos diferentes anexos estão apresentados vários documentos tais como o modelo de folha de cálculo para tratamento de dados relativos ao ensaio, modelo de folha de cálculo para tratamento de dados relativo às calibrações, modelo de relatório de ensaio, modelo de certificado de calibração, folhas de cálculo para gestão de clientes/equipamentos e numeração automática de relatórios de ensaio e certificados de calibração que cumprem os requisitos de gestão do laboratório. Ainda em anexo constam todas as figuras relativas à monitorização da temperatura nas câmara térmicas como também as figuras da disposição dos termómetros no interior das câmaras térmicas. Todas as figuras que aparecem ao longo do documento que não estão referenciadas são da adaptação ou elaboração própria do autor. A decisão de alargar o âmbito da acreditação do Laboratório de Metrologia da Frilabo para calibração de termómetros, prendeu-se com o facto de que sendo acreditado como laboratório de ensaios na área das temperaturas, a realização da rastreabilidade dos padrões de medida internamente, permitiria uma gestão de recursos otimizada e rentabilizada. A metodologia da preparação de todo o processo de acreditação do Laboratório de Metrologia da Frilabo, foi desenvolvida pelo autor e está expressa ao longo do texto da tese incluindo dados relevantes para a concretização da referida acreditação nos dois âmbitos. A avaliação de todo o trabalho desenvolvido será efetuada pelo o organismo designado IPAC (Instituto Português de Acreditação) que confere a acreditação em Portugal. Este organismo irá auditar a empresa com base nos procedimentos desenvolvidos e nos resultados obtidos, sendo destes o mais importante o Balanço da Melhor Incerteza (BMI) da medição também conhecido por Melhor Capacidade de Medição (MCM), quer para o ensaio às câmaras térmicas, quer para a calibração dos termómetros, permitindo desta forma complementar os serviços prestados aos clientes fidelizados à Frilabo. As câmaras térmicas e os termómetros industriais são equipamentos amplamente utilizados em diversos segmentos industriais, engenharia, medicina, ensino e também nas instituições de investigação, sendo um dos objetivos respetivamente, a simulação de condições específicas controladas e a medição de temperatura. Para entidades acreditadas, como os laboratórios, torna-se primordial que as medições realizadas com e nestes tipos de equipamentos ostentem confiabilidade metrológica1, uma vez que, resultados das medições inadequados podem levar a conclusões equivocadas sobre os testes realizados. Os resultados obtidos nos ensaios a câmaras térmicas e nas calibrações de termómetros, são considerados bons e aceitáveis, uma vez que as melhores incertezas obtidas, podem ser comparadas, através de consulta pública do Anexo Técnico do IPAC, com as incertezas de outros laboratórios acreditados em Portugal. Numa abordagem mais experimental, pode dizer-se que no ensaio a câmaras térmicas a obtenção de incertezas mais baixas ou mais altas depende maioritariamente do comportamento, características e estado de conservação das câmaras, tornando relevante o processo de estabilização da temperatura no interior das mesmas. A maioria das fontes de incerteza na calibração dos termómetros são obtidas pelas características e especificações do fabricante dos equipamentos, que se traduzem por uma contribuição com o mesmo peso para o cálculo da incerteza expandida (a exatidão de fabricante, as incertezas herdadas de certificados de calibração, da estabilidade e da uniformidade do meio térmico onde se efetuam as calibrações). Na calibração dos termómetros as incertezas mais baixas obtêm-se para termómetros de resoluções mais baixas. Verificou-se que os termómetros com resolução de 1ºC não detetavam as variações do banho térmico. Nos termómetros com resoluções inferiores, o peso da contribuição da dispersão de leituras no cálculo da incerteza, pode variar consoante as características do termómetro. Por exemplo os termómetros com resolução de 0,1ºC, apresentaram o maior peso na contribuição da componente da dispersão de leituras. Pode concluir-se que a acreditação de um laboratório é um processo que não é de todo fácil. Podem salientar-se aspetos que podem comprometer a acreditação, como por exemplo a má seleção do ou dos técnicos e equipamentos (má formação do técnico, equipamento que não seja por exemplo adequado à gama, mal calibrado, etc…) que vão efetuar as medições. Se não for bem feita, vai comprometer todo o processo nos passos seguintes. Deve haver também o envolvimento do todos os intervenientes do laboratório, o gestor da qualidade, o responsável técnico e os técnicos, só assim é que é possível chegar à qualidade pretendida e à melhoria contínua da acreditação do laboratório. Outro aspeto importante na preparação de uma acreditação de um laboratório é a pesquisa de documentação necessária e adequada para poder tomar decisões corretas na elaboração dos procedimentos conducentes à referida. O laboratório tem de mostrar/comprovar através de registos a sua competência. Finalmente pode dizer-se que competência é a palavra chave de uma acreditação, pois ela manifesta-se nas pessoas, equipamentos, métodos, instalações e outros aspetos da instituição a que pertence o laboratório sob acreditação.

Desenvolvimento de um método para correção de curvas de desempenho em bombas centrífugas submersas operando com fluidos viscosos

Electrical Submersible Pump (ESP) is used as an artificial lift technique. However, pumping viscous oil is generally associated with low Reynolds number flows. This condition leads to a performance degradation respect to the performance expected from the regular operation with water that most of the centrifugal pumps are originally designed for. These issues are considered in this investigation through a numerical study of the flow in two different multistage, semi-axial type ESPs. This investigation is carried out numerically using a Computational Fluid Dynamics (CFD) package, where the transient RANS equations are solved numerically. The turbulence is modeled using the SST model. Head curves for several operating conditions are compared with manufacturer’s curves and experimental data for a three-stage ESP, showing good agreement for a wide range of fluid viscosities and rotational speeds. Dimensionless numbers (n, n, n e Re) are used to investigate performance degradation of the ESPs. In addition, flow phenomena through the impellers of the ESPs are investigated using flow field from numerical results. Results show that performance degradation is directly related to rotational Reynolds number, Re. In addition, it was verified that performance degradation occurs for constant normalized specific speedn, which shows that performance degradation occurs similarly for different centrifugal pumps. Moreover, experimental data and numerical results agreed with a correlation from literature between head and flow correction factors proposed by Stepanoff (1967). A definition of modified Reynolds number was proposed and relates the head correction factor to viscosity. A correlation between head correction factor and the modified Reynolds number was proposed, which agreed well with numerical and experimental data. Then, a method to predict performance degradation based on the previous correlations was proposed. This method was compared with others from literature. In general, results and conclusions from this work can also be useful to bring more information about the flow of highly viscous fluids in pumps, especially in semi-axial, multistage ESPs.

Modelo para formação dinâmica de rede de fornecedores em empresas estendidas

Supply chains have become an important focus for competitive advantage. The performance of a company increasingly depends on its ability to maintain effective and efficient relationships with its suppliers and customers. The extended enterprise (i.e. composed of several partners) needs to be dynamically formed in order to be agile and adaptable. According to the Digital Manufacturing paradigm, companies have to be able to quickly share and disseminate information regarding planning, designing and manufacturing of products. Additionally, they must be responsive to all technical and business determinants, as well as be assessed and certified for guaranteed performance. The current research intends to present a solution for the dynamic composition of the extended enterprise, formed to take advantage of market opportunities quickly and efficiently. A construction model was developed. This construction model consists of: information model, protocol model and process model. The information model has been defined based on the concepts of Supply Chain Operations Reference model (SCOR®). In this model is defined information for negotiating the participation of candidate companies in the dynamic establishment of a network for responding to a given demand for developing and manufacturing products, in seven steps as follows: request for information; request for qualification; alignment of strategy; request for proposal; request for quotation; compatibility of process; and compatibility of system. The protocol model has been elaborated and inspired in the OSI, this model provides a framework for linking customers and suppliers, indicates a sequence to be followed, in order to selecte companies to become suppliers. The process model has been implemented by means of process modeling according to the BPMN standard and, in turn, implemented as a web-based application that runs the process through its several steps, which uses forms to gather data. An application example in the context of the oil and gas industry is used for demonstrating the solution concept.