干旱对沙棘休眠、萌芽期内源激素及萌芽特性的影响

以 2a生中国沙棘为试验材料 ,研究了土壤干旱胁迫下沙棘苗木水分生理状况 ,内源GA1 3 及ABA水平与萌芽率的关系 ,结果表明 :土壤干旱胁迫导致苗体含水量、水势、自由水含量下降 ,显著提高冬季休眠与春季萌动期的内源ABA水平而降低内源GA1 3 含量 ,GA1 3 ABA降低 ,较晚达到萌动所需的调控阈值 ,萌芽延迟。重度胁迫下苗木延迟达 2 5d且萌芽后生长缓慢。长期土壤中度干旱条件下沙棘苗萌芽期亦略有延迟 ,萌芽后生长略有抑制

沈阳城市森林主要树种物候对气候变暖的响应

采用统计和线性回归方法,探讨了近40年来沈阳城市森林主要树种物候对气候变暖的响应.结果表明,沈阳城市森林树木休眠期长短与冬季气温密切相关,适宜的寒冷条件有利于解除树木休眠期;树木萌动期早晚与冬季和早春气温高低呈显著的负相关关系,冬春季气温越高,芽萌动越提前.树木爆芽后15d左右开始展叶,展叶早晚主要受展叶前的春季气温高低的影响,但与冬季气温没有相关关系.始花前2~8旬,特别是2~4旬气温对始花期影响最显著,春季气温升高始花期提前.树木芽萌动期、展叶始期与寒冷指数(CI)呈显著正相关关系,而开花始期与CI没有相关关系.沈阳城市森林树木对气候变暖的响应,主要表现在年均温升高1℃,芽萌动期提前9d,展叶始期提前10d,开花始期提前5d.

石油污染土壤堆制微生物降解研究

采用异位生物修复技术堆式堆制处理方法 ,对辽河油田原油污染土壤进行了生物修复处理研究 .处理工程设 4个处理料堆单元 ,每个处理单元长 118.5cm ,宽 6 5 .5cm ,高 12 .5cm .研究结果表明 ,当进行处理的石油污染土壤中石油烃总量为 5 .2 2 g·10 0 g-1土时 ,利用黄孢原毛平革菌 (Phanerochaetechrysospori um) ,经过 5 5d的运行 ,石油烃总量去除率达 5 4.2 % .堆制处理中影响污染土壤石油烃总量生物降解的主要变化因子为污染土壤的O2 和CO2 含量、降解石油烃微生物的数量、污染土壤pH的变化 .通过监测这些数据的变化 ,可直接反映该工程的处理石油污染土壤的效果 .本处理工程采用定期通风措施 ,操作简单、运行费用低廉 ,为石油污染土壤生物修复实用化提供了一种简单易行的污染土壤清洁技术 .

土壤中嗜酸性氧化亚铁硫杆菌的分离鉴定及其性能研究

采用改进型Leathen培养基直接从辽宁省抚顺市红透山铜矿附近的土壤中分离到了一株高度嗜酸的氧化亚铁硫杆菌(Acidithiobacillus ferrooxidans)菌株(暂命名为R2)。鉴定表明,该菌株为革兰氏阴性细菌,在扫描电镜下观察该菌株为短杆状,菌体大小为(0.4±0.2)μm×(1.6±0.4)μm。最适pH值2.0,化能自养型,能利用亚铁、单质硫和硫代硫酸钠生长,不能利用葡萄糖、蛋白胨生长。并且以16S rDNA序列同源性为基础构建了17株已报道菌种在内的系统发育树,将16S rDNA测序结果输入Genebank以Blast软件进行序列同源性比较,结果显示与氧化亚铁硫杆菌(Acidithiobacillus ferrooxidans)的多株细菌具有较高的同源性(>99%),其中与Acidithiobacillus ferrooxidans strain TGS的相似性达到100%,与标准株Acidithiobacillus ferrooxidans strain ATCC33020相似性为99.3%,结合其生理生化特性可以确定该菌为氧化亚铁硫杆菌种。序批式试验法研究表明,接种该株菌可有效溶出土壤中重金属,经过5d的生物淋滤,Cu、Cr、Zn、Cd的最高去除率分别达到30.6%、16.3%、58.4%和72%。

亚硝化细菌的筛选及培养条件的研究

从活性污泥中分离出16株亚硝化细菌,筛选出亚硝酸盐氮积累速率较高的两株菌Y8和Y16,初步鉴定Y8菌株为亚硝化球菌(Nitrosococcns.sp),Y16菌株为亚硝化单胞菌(Nitrosomonas.sp),并对其生长曲线进行了测定。通过氨氮去除率或亚硝酸盐氮的质量浓度来验证亚硝化细菌的活性,考察了生成的亚硝酸盐氮的质量浓度与培养时间的关系、亚硝化细菌的活性与培养温度的关系、亚硝化细菌的活性与培养基pH的关系。Y8和Y16菌株在30℃、培养基pH为7.5、130r/min的条件下振荡培养5d,氨氮去除率分别为81.12%,75.36%。

One-Dimensional Ce3+- and/or Tb3+-Doped X-1-Y2SiO5 Nanofibers and Microbelts: Electrospinning Preparation and Luminescent Properties

One-dimensional X-1-Y2SiO5:Ce3+ and -Tb3+ nanofibers and quasi-one-dimensional X-1-Y2SiO5:Ce3+ and -Tb3+ microbelts have been prepared by a simple and cost-effective electrospinning process. X-ray powder diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy (SEM), energy-dispersive X-ray spectrometry, transmission electron microscopy, high-resolution transmission electron microscopy, photoluminescence (PL), and cathodoluminescence spectra were used to characterize the samples. SEM results indicate that the as-prepared fibers and belts are smooth and uniform with a length of several tens to hundreds of micrometers, whose diameters decrease after being annealed at 1000 degrees C for 3 h. Under ultraviolet excitation and low-voltage electron beam excitation, the doped rare earth ions show their characteristic emission, that is, Ce3+ 5d-4f and Tb3+ D-5(4)-F-7(J) (J = 6, 5 4, 3) transitions, respectively.

In Situ Preparation and Luminescent Properties of CeF3 and CeF3:Tb3+ Nanoparticles and Transparent CeF3:Tb3+/PMMA Nanocomposites in the Visible Spectral Range

CeF3 and CeF3:Tb3+ nanoparticles were prepared by reverse microemulsion with a functional monomer, methyl methacrylate (MMA), as the oil phase, and CeF3:Tb3+/poly (methyl methacrylate) (PMMA) nanocomposites were obtained via polymerization of the MMA monomer. The nanoparticles and nanocomposites have been well characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), low- and high-resolution transmission electron microscope (TEM), selected-area electron diffraction (SAED), thermogravimetric analysis (TGA), UV/vis transmission spectra, photoluminescence excitation, and emission spectra and luminescence decays. The well-crystallized CeF3 and CeF3:Tb3+ nanoparticles are spherical with a mean diameter of 15 nm. They show the characteristic emission of Ce3+ 5d-4f (313 nm, D-2-F-2(5/2); 323 nm, D-2-F-2(7/2)) and Tb3+ D-5(4)-F-7(J) (J = 6-3, with D-5(4)-F-7(5) green emission at 541 nm as the strongest one) transitions, respectively.

Reduction of Eu3+ to Eu2+ in MAl2Si2O8 (M = Ca, Sr, Ba) in air condition

In general, the reduction of Eu3+ to Eu2+ in solids needs an annealing Process in a reducing atmosphere. in this paper, it is of great interest and importance to find that the reduction of Eu3+ to Eu2+ can be realized in a series of alkaline-earth metal aluminum silicates MAl2Si2O8 (M = Ca, Sr, Ba) just in air condition. The Eu2+-doped MAl2Si2O8 (M = Ca, Sr, Ba) powder samples were prepared in air atmosphere by Pechini-type sol-gel process. It was found that the strong hand emissions of 4f(6)5d(1)-4f(7) from Eu2+ were observed at 417, 404 and 373 nm in air-annealed CaAl2Si2O8, SrAl2Si2O8 and BaAl2Si2O8, respectively, under ultraviolet excitation although the Eu3+ precursors were employed. In addition, under low-voltage electron beam excitation, Eu2+-doped MAl2Si2O8 also shows strong blue or ultraviolet emission corresponding to 4f(6)5d(1)-4f(7) transition.

Preparation and luminescence properties of Ce3+ and/or Tb3+ doped LaPO4 nanofibers and microbelts by electrospinning

Ce3+ and/or Tb3+ doped LaPO4 nanofibers and microbelts have been prepared by a combination method of sol-gel process and electrospinning. X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), photoluminescence (PL), low voltage cathodoluminescence (CL) and time-resolved emission spectra as well as kinetic decays were used to characterize the resulting samples. SEM and TEM results indicate the as-formed precursor fibers and belts are smooth. and the as-prepared nanofibers and microbelts consist of nanoparticles. The doped rare-earth ions show their characteristic emission under ultraviolet excitation, i.e. Ce3+ 5d-4f and Tb3+ D-5(4)-F-7(j) (J = 6-3) transitions, respectively. The energy transfer process from Ce3+ to Tb3+ in LaPO4:Ce3+, Tb3+ nanofibers was further studied by the time-resolved emission spectra.

LaF3, CeF3, CeF3 : Tb3+, and CeF3 : Tb3+@LaF3 (core-shell) nanoplates: Hydrothermal synthesis and luminescence properties

LaF3. CeF3, CeF3:Tb3+, and CeF3:Tb3+ @LaF3 (core-shell) 2D nanoplates have been successfully synthesized by a facile and effective hydrothermal process. X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), and photoluminescence (PL) spectra as well as kinetic decays were used to characterize the samples. The experimental results indicate that the organic additive, trisodium citrate (Cit(3-)), as a shape modifier has the dynamic effect by adjusting the growth rate of different crystal facets, resulting in forming the anisotropic geometries of the final products. The possible formation mechanisms for different products have been presented. The CeF3, CeF3:Tb3+, and CeF3:Tb3+ @LaF3 (core/shell) nanoplates show characteristic emission of Ce3+ (5d-4f) and Tb3+ (f-f), respectively.

Synthesis, photoluminescence, thermoluminescence and dosimetry properties of novel phosphor KSr4(BO3)(3):Ce

Polycrystalline powder sample of KSr4(BO3)(3) was synthesized by high-temperature solid-state reaction. The influence of different rare earth dopants, i.e. Tb3+, TM3+ and Ce3+, on thermoluminescence (TL) of KSr4(BO3)(3) Phosphor was discussed. The TL, photoluminescence (PL) and some dosimetric properties of Ce3+-activated KSr4(BO3)(3) phosphor were studied. The effect of the concentration of Ce3+ on TL intensity was investigated and the result showed that the optimum Ce3+ concentration was 0.2 mol%. The TL kinetic parameters of KSr4(BO3)(3):0.002 Ce3+ phosphor were calculated by computer glow curve deconvolution (CGCD) method. Characteristic emission peaking at about 407 and 383 nm due to the 4f(0)5d(1) -> F-2((5/2),(7/2)) transitions of Ce3+ ion were observed both in PL and three-dimensional (3D) TL spectra. The dose-response of KSr4(BO3)(3):0.002 Ce3+ to gamma-ray was linear in the range from 1 to 1000 mGy. In addition, the decay of the TL intensity of KSr4(BO3)(3):0.002 Ce3+ was also investigated.

Thermoluminescence characteristics of NaSr4(BO3)(3):Ce3+ under beta-ray irradiation

The thermoluminescence (TL) properties of Ce3+ doped NaSr4(BO3)(3) phosphor under the beta-ray irradiation were reported. The polycrystalline sample was synthesized by high temperature solid-state reaction. The TL glow curve of NaSr4(BO3)(3):Ce3+ phosphor was composed of only one peak. TL kinetic parameters of NaSr4(BO3)(3):Ce3+ were deduced by the peak shape method, the activation energy (E) was 0.590 eV and the frequency factor was 1.008x10(6) s(-1). TL dose response was linear in the range of measurement. The 3-dimensional (3D) TL emission spectrum was also recorded, the emission spectrum consisted of two bands located at 441 and 479 nm respectively, corresponding to the characteristic 4f(0)5d(1)-> F-2((5/2,7/2)) transitions of the Ce3+ ion. The fading behavior of the NaSr4(BO3)(3):Ce3+ phosphor over a period of 15 d was also studied.

Luminescent properties of a new blue long-lasting phosphor Ca2P2O7:Eu2+, Y3+

A new pyrophosphate long-lasting phosphor with composition of Ca1.96P2O7:0.02Eu(2+), 0.02Y(3+) is synthesized via the high-temperature solid-state reaction method. Its properties are systematically investigated utilizing XRD, photoluminescence, phosphorescence and thermoluminescence (TL) spectra. The phosphor emits blue light that is related to the characteristic emission of Eu2+ due to 5d-4f transitions. For the optimized sample, bright blue long-lasting phosphorescence (LLP) could be observed by naked eyes even 6 h after the excitation source is removed. The TL spectra show that the doping of Y3+ ions greatly enhanced intensity of 335 K peak and created new TL peak at about 373 K that is also responsible for the blue LLP. Based on our study, Y3+ ions are suggested to act as electron traps to improve the performance of the blue phosphorescence of Eu2+ such as intensity and persistent time.

novel blue-emitting long-lasting proyphosphate phosphor Sr2P2O7:Eu2+, Y3+

By introducing the Y3+ into Sr2P2O7:Eu2+, we successfully prepared a kind of new phosphor with blue long-lasting phosphorescence by the high-temperature solid-state reaction method. In this paper, the properties of Sr2P2O7:Eu2+, Y3+ were investigated utilizing XRD, photoluminescence, luminescence decay, long-lasting phosphorescence and thermoluminescence (TL) spectra. The phosphor emitted blue light that was related to the 4f(6)5d(1)-S-8(7/2) transition of Eu2+. The bright blue phosphorescence could be observed by naked eyes even 8 h after the excitation source was removed. Two TL peaks at 317 and 378 K related to two types of defects appeared in the TL spectrum. By analyzing the TL curve the depths of traps were calculated to be 0.61 and 0.66 eV. Also, the mechanism of LLP was discussed in this report.

Synthesis and characterization of monodisperse spherical core-shell structured SiO2@Y3Al5O12 : Ce3+/Tb3+ phosphors for field emission displays

Nanocrystalline Y3Al5O12: Ce3+/Tb3+ ( average crystalline size 30 nm) phosphor layers were coated on non-aggregated, monodisperse and spherical SiO2 particles by the sol-gel method, resulting in the formation of core-shell structured SiO2@Y3Al5O12:Ce3+/Tb3+ particles. X-ray diffraction, Fourier transform infrared spectroscopy, transmission electron microscopy, photoluminescence, cathodoluminescence spectra, as well as lifetimes were utilized to characterize the core-shell structured SiO2@Y3Al5O12: Ce3+/Tb3+ phosphor particles. The obtained core-shell structured phosphors consist of well-dispersed submicron spherical particles with a narrow size distribution. The thickness of the Y3Al5O12:Ce3+/Tb3+ shells on the SiO2 cores ( average size about 500 nm, crystalline size about 30 nm) could be easily tailored by varying the number of deposition cycles (100 nm for four deposition cycles). Under the excitation of ultraviolet and low-voltage electron beams (1-3 kV), the core-shell SiO2@Y3Al5O12:Ce3+/ Tb3+ particles show strong yellow-green and green emission corresponding to the 5d-4f emission of Ce3+ and D-5(4)-F-7(J) ( J = 6, 5, 4, 3) emission of Tb3+, respectively.