Demonstration of Radio-over-Fibre Transmission of Broadband MIMO over Multimode Fibre using Mode Division Multiplexing

Abstract (40-Word Limit): A novel method for sending MIMO wireless signals to remote antenna units over a single multimode fibre is proposed. MIMO streams are sent via different fibre modes using mode division multiplexing. Combined channel measurements of 2km MMF and a typical indoor radio environment show in principle a 2x2 MIMO link at carrier frequencies up to 6GHz.

The high strain rate response of Ultra High Molecular-weight Polyethylene: From fibre to laminate

The effect of strain rate upon the uniaxial response of Ultra High Molecular-weight Polyethylene (UHMWPE) fibres, yarns and laminates of lay-up [0/90]48 has been measured in both the 0/90 and ±45 configurations. The tensile strength of the matrix-dominated ±45 laminate is two orders of magnitude less than that of the fibre-dominated 0/90 laminate, and is more sensitive to strain rate. A piezoelectric force sensor device was developed to obtain the high strain rate data, and this achieved a rise time of less than 1 μs. It is found that the failure strength (and failure strain) of the yarn is almost insensitive to strain rate within the range (10 -1-103 s-1). At low strain rates (below 10 -1 s-1), creep of the yarn dominates and the failure strain increases with diminishing strain rate. The tensile strength of the dry yarn exceeds that of the laminate by about 20%. Tests on single fibres exceed the strength of the yarn by 20%. © 2013 Elsevier Ltd. All rights reserved.

Short-term cytotoxic and inflammatory responses of human monocytes to stainless steel fibre networks

The aim of the current work was to examine the human monocyte response to 444 ferritic stainless steel fibre networks. 316L austenitic fibre networks, of the same fibre volume fraction, were used as control surfaces. Fluorescence and scanning electron microscopies suggest that the cells exhibited a good degree of attachment and penetration throughout both networks. Lactate Dehydrogenase (LDH) and TNF-α releases were used as indicators of cytotoxicity and inflammatory responses respectively. LDH release indicated similar levels of monocyte viability when in contact with the 444 and 316L fibre networks. Both networks elicited a low level secretion of TNF-α, which was significantly lower than that of the positive control wells containing zymosan. Collectively, the results suggest that 444 ferritic and 316L austenitic networks induced similar cytotoxic and inflammatory responses from human monocytes. © 2012 Materials Research Society.

Optical vortex based Mode Division Multiplexing over graded-index multimode fibre

Mode Division Multiplexing is performed over 2km and 8km of 50μm graded-index multimode fibre using (de)multiplex phase masks based around optical vortex modes to transmit 2×56Gbps QPSK signals without MIMO equalization. © 2013 OSA.

Orthogonal multipulse modulation for 64 Gigabit Fibre Channel

Real-time orthogonal multipulse modulation is demonstrated at 56 Gb/s with transmission over 500 m of single-mode fiber. Up to 2 dBo power budget advantage is predicted relative to alternatives such as PAM4. © 2013 OSA.

Transmission of simultaneous 10Gb/s Ethernet and radio-over-fibre transmission using in-band coding

A technique using spectrum-shaping codes to create nulls in the baseband spectrum of an Ethernet signal, so that several RF signals can be inserted in-band, is demonstrated by simultaneous transmission of 10GbE and WCDMA signals. © 2013 OSA.

2x56-Gb/s mode-division multiplexed transmission over 2km of om2 multimode fibre without MIMO equalization

A Spatial Light Modulator is used to optically demultiplex modal channels on the basis of degenerate propagation constants using a shared phase mask for all channels. This allows groups of modes to be routed to common output fibres eliminating the need for MIMO equalization to transmit 2x56Gb/s QPSK over 2km of OM2 grade 50μm core MMF. © 2012 OSA.

FEC-free 50 m 1.5 Gb/s plastic optical fibre link using CAP modulation for home networks

LED-based carrierless amplitude and phase modulation is investigated for a multi-gigabit plastic optical fibre link. An FPGA-based 1.5 Gbit/s error free transmission over 50 m standard SI-POF using CAP64 is achieved, providing 2.9 dB power margin without forward error correction. © 2012 OSA.

Optical vortex based mode division multiplexing over graded-index multimode fibre

Mode Division Multiplexing is performed over 2km and 8km of 50μm graded-index multimode fibre using (de)multiplex phase masks based around optical vortex modes to transmit 2x56Gbps QPSK signals without MIMO equalization. © 2013 OSA.

Orthogonal multipulse modulation for 64 gigabit fibre channel

Real-time orthogonal multipulse modulation is demonstrated at 56 Gb/s with transmission over 500 m of single-mode fiber. Up to 2 dBo power budget advantage is predicted relative to alternatives such as PAM4. © 2013 OSA.

Transmission of simultaneous 10Gb/s ethernet and radioover-fibre transmission using in-band coding

A technique using spectrum-shaping codes to create nulls in the baseband spectrum of an Ethernet signal, so that several RF signals can be inserted in-band, is demonstrated by simultaneous transmission of 10GbE and WCDMA signals. © 2013 OSA.

High performance fibre-reinforced cementitious composite (CARDIFRC) - Performance and application to retrofitting

This paper describes first some of the recent performance checks on the high performance fibre-reinforced cementitious composite CARDIFRC and then its application to the retrofitting of damaged concrete beams. It is shown that an even distribution of fibres throughout the bulk of the material is crucial to its excellent fatigue performance and to the reduction in the autogenous shrinkage strains. The distribution of fibres in beams, cylinders and strips is examined using computerised tomography imaging and traditional image analysis. Thin strips of CARDIFRC are used to retrofit damaged concrete beams which are subjected to thermal cycling. It is shown that neither the load carrying capacity of the retrofitted beams nor the bond between retrofit strips and concrete deteriorates with thermal cycling. The load carrying capacity of retrofitted beams is predicted with a model based on fracture mechanics, and the predictions are shown to be in good agreement with test data. © 2006 Elsevier Ltd. All rights reserved.

Friction between carbon fibre reinforced polymers: Experiments and modelling

Carbon fibre reinforced polymers (CFRP) are well-known for the excellent combination of mechanical and thermal properties with light weight. However, their tribological properties are still largely uncovered. In this work an experimental study of friction between two CFRP at weak normal load (inferior to 20 N) was performed. Two effects were scrutinuously studied during the experiments: fibre volume friction and fibre orientation. In addition to this experimental work, a modelling of a contact between two FRP was realized. It is supposed that the real area of contact consists of a multitude of microcontacts of three types: fibre-fibre, fibre-matrix and matrix-matrix. The experimental work has shown a small rise in friction coefficient with the change of fibre orientation of two composites from parallel to perpendicular relative to the sliding direction. In parallel, the proposed analytical model predicts a independence of this angle. Regarding the influence of the fibre volume fraction, Vf, the experiments reveal a decrease in friction coefficient of 50% with a change of Vf from 0% to 62%. This observation corresponds to the qualitative dependence depicted with the model. © 2012 EDP Sciences.

Corrugated all-composite sandwich structures. Part 2: Failure mechanisms and experimental programme

A novel corrugated composite core, referred to as a hierarchical corrugation, has been developed and tested experimentally. Hierarchical corrugations exhibit a range of different failure modes depending on the geometrical properties and the material properties of the structures. In order to understand the different failure modes the analytical strength model, developed in part 1 of this paper, was used to make collapse mechanism maps for the different corrugation configurations. If designed correctly, the hierarchical structures can have more than 7 times higher weight specific strength compared to its monolithic counter part. The difference in strength arises mainly from the increase in buckling resistance of the sandwich core members compared to the monolithic version. The highest difference in strength is seen for core configurations with low overall density. As the density of the core increases, the monolithic core members get stockier and more resistant to buckling and thus the benefits of the hierarchical structure reduces. © 2008 Elsevier Ltd. All rights reserved.