Heavy vehicle suspensions : testing and analysis

Transport regulators consider that, with respect to pavement damage, heavy vehicles (HVs) are the riskiest vehicles on the road network. That HV suspension design contributes to road and bridge damage has been recognised for some decades. This thesis deals with some aspects of HV suspension characteristics, particularly (but not exclusively) air suspensions. This is in the areas of developing low-cost in-service heavy vehicle (HV) suspension testing, the effects of larger-than-industry-standard longitudinal air lines and the characteristics of on-board mass (OBM) systems for HVs. All these areas, whilst seemingly disparate, seek to inform the management of HVs, reduce of their impact on the network asset and/or provide a measurement mechanism for worn HV suspensions. A number of project management groups at the State and National level in Australia have been, and will be, presented with the results of the project that resulted in this thesis. This should serve to inform their activities applicable to this research. A number of HVs were tested for various characteristics. These tests were used to form a number of conclusions about HV suspension behaviours. Wheel forces from road test data were analysed. A “novel roughness” measure was developed and applied to the road test data to determine dynamic load sharing, amongst other research outcomes. Further, it was proposed that this approach could inform future development of pavement models incorporating roughness and peak wheel forces. Left/right variations in wheel forces and wheel force variations for different speeds were also presented. This led on to some conclusions regarding suspension and wheel force frequencies, their transmission to the pavement and repetitive wheel loads in the spatial domain. An improved method of determining dynamic load sharing was developed and presented. It used the correlation coefficient between two elements of a HV to determine dynamic load sharing. This was validated against a mature dynamic loadsharing metric, the dynamic load sharing coefficient (de Pont, 1997). This was the first time that the technique of measuring correlation between elements on a HV has been used for a test case vs. a control case for two different sized air lines. That dynamic load sharing was improved at the air springs was shown for the test case of the large longitudinal air lines. The statistically significant improvement in dynamic load sharing at the air springs from larger longitudinal air lines varied from approximately 30 percent to 80 percent. Dynamic load sharing at the wheels was improved only for low air line flow events for the test case of larger longitudinal air lines. Statistically significant improvements to some suspension metrics across the range of test speeds and “novel roughness” values were evident from the use of larger longitudinal air lines, but these were not uniform. Of note were improvements to suspension metrics involving peak dynamic forces ranging from below the error margin to approximately 24 percent. Abstract models of HV suspensions were developed from the results of some of the tests. Those models were used to propose further development of, and future directions of research into, further gains in HV dynamic load sharing. This was from alterations to currently available damping characteristics combined with implementation of large longitudinal air lines. In-service testing of HV suspensions was found to be possible within a documented range from below the error margin to an error of approximately 16 percent. These results were in comparison with either the manufacturer’s certified data or test results replicating the Australian standard for “road-friendly” HV suspensions, Vehicle Standards Bulletin 11. OBM accuracy testing and development of tamper evidence from OBM data were detailed for over 2000 individual data points across twelve test and control OBM systems from eight suppliers installed on eleven HVs. The results indicated that 95 percent of contemporary OBM systems available in Australia are accurate to +/- 500 kg. The total variation in OBM linearity, after three outliers in the data were removed, was 0.5 percent. A tamper indicator and other OBM metrics that could be used by jurisdictions to determine tamper events were developed and documented. That OBM systems could be used as one vector for in-service testing of HV suspensions was one of a number of synergies between the seemingly disparate streams of this project.

Compliant cryptologic protocols

Literally, the word compliance suggests conformity in fulfilling official requirements. The thesis presents the results of the analysis and design of a class of protocols called compliant cryptologic protocols (CCP). The thesis presents a notion for compliance in cryptosystems that is conducive as a cryptologic goal. CCP are employed in security systems used by at least two mutually mistrusting sets of entities. The individuals in the sets of entities only trust the design of the security system and any trusted third party the security system may include. Such a security system can be thought of as a broker between the mistrusting sets of entities. In order to provide confidence in operation for the mistrusting sets of entities, CCP must provide compliance verification mechanisms. These mechanisms are employed either by all the entities or a set of authorised entities in the system to verify the compliance of the behaviour of various participating entities with the rules of the system. It is often stated that confidentiality, integrity and authentication are the primary interests of cryptology. It is evident from the literature that authentication mechanisms employ confidentiality and integrity services to achieve their goal. Therefore, the fundamental services that any cryptographic algorithm may provide are confidentiality and integrity only. Since controlling the behaviour of the entities is not a feasible cryptologic goal,the verification of the confidentiality of any data is a futile cryptologic exercise. For example, there exists no cryptologic mechanism that would prevent an entity from willingly or unwillingly exposing its private key corresponding to a certified public key. The confidentiality of the data can only be assumed. Therefore, any verification in cryptologic protocols must take the form of integrity verification mechanisms. Thus, compliance verification must take the form of integrity verification in cryptologic protocols. A definition of compliance that is conducive as a cryptologic goal is presented as a guarantee on the confidentiality and integrity services. The definitions are employed to provide a classification mechanism for various message formats in a cryptologic protocol. The classification assists in the characterisation of protocols, which assists in providing a focus for the goals of the research. The resulting concrete goal of the research is the study of those protocols that employ message formats to provide restricted confidentiality and universal integrity services to selected data. The thesis proposes an informal technique to understand, analyse and synthesise the integrity goals of a protocol system. The thesis contains a study of key recovery,electronic cash, peer-review, electronic auction, and electronic voting protocols. All these protocols contain message format that provide restricted confidentiality and universal integrity services to selected data. The study of key recovery systems aims to achieve robust key recovery relying only on the certification procedure and without the need for tamper-resistant system modules. The result of this study is a new technique for the design of key recovery systems called hybrid key escrow. The thesis identifies a class of compliant cryptologic protocols called secure selection protocols (SSP). The uniqueness of this class of protocols is the similarity in the goals of the member protocols, namely peer-review, electronic auction and electronic voting. The problem statement describing the goals of these protocols contain a tuple,(I, D), where I usually refers to an identity of a participant and D usually refers to the data selected by the participant. SSP are interested in providing confidentiality service to the tuple for hiding the relationship between I and D, and integrity service to the tuple after its formation to prevent the modification of the tuple. The thesis provides a schema to solve the instances of SSP by employing the electronic cash technology. The thesis makes a distinction between electronic cash technology and electronic payment technology. It will treat electronic cash technology to be a certification mechanism that allows the participants to obtain a certificate on their public key, without revealing the certificate or the public key to the certifier. The thesis abstracts the certificate and the public key as the data structure called anonymous token. It proposes design schemes for the peer-review, e-auction and e-voting protocols by employing the schema with the anonymous token abstraction. The thesis concludes by providing a variety of problem statements for future research that would further enrich the literature.

Probability and statistics

Now in its sixth edition, the Traffic Engineering Handbook continues to be a must have publication in the transportation industry, as it has been for the past 60 years. The new edition provides updated information for people entering the practice and for those already practicing. The handbook is a convenient desk reference, as well as an all in one source of principles and proven techniques in traffic engineering. Most chapters are presented in a new format, which divides the chapters into four areas-basics, current practice, emerging trends and information sources. Chapter topics include road users, vehicle characteristics, statistics, planning for operations, communications, safety, regulations, traffic calming, access management, geometrics, signs and markings, signals, parking, traffic demand, maintenance and studies. In addition, as the focus in transportation has shifted from project based to operations based, two new chapters have been added-"Planning for Operations" and "Managing Traffic Demand to Address Congestion: Providing Travelers with Choices." The Traffic Engineering Handbook continues to be one of the primary reference sources for study to become a certified Professional Traffic Operations Engineer™. Chapters are authored by notable and experienced authors, and reviewed and edited by a distinguished panel of traffic engineering experts.

Colorectal cancer survivors’ exercise experiences and preferences : qualitative findings from an exercise rehabilitation programme immediately after chemotherapy

Little is known about cancer survivors’ experiences with and preferences for exercise programmes offered during rehabilitation (immediately after cancer treatment). This study documented colorectal cancer survivors’ experiences in an exercise rehabilitation programme and their preferences for programme content and delivery. At the completion of 12-weeks of supervised exercise, 10 participants took part in one-on-one semi-structured interviews. Data from these interviews were coded, and themes were identified using qualitative software. Key findings were that most participants experienced improvements in treatment symptoms, including reduced fatigue and increased energy and confidence to do activities of daily living. They also reported that interactions with the exercise trainer and a flexible programme delivery were important aspects of the intervention. Most participants reported that they preferred having a choice of exercise, starting to exercise within a month after completing treatment, having supervision and maintaining a one-on-one format. Frustrations included scheduling conflicts and a lack of a transition out of the programme. The findings indicate that colorectal cancers experience benefits from exercise offered immediately after treatment and prefer individual attention from exercise staff. They further indicate directions for the implementation of future exercise programmes with this population.

Coordinated research skills training at QUT

Universities are wanting to drive research performance to new levels to increase competitiveness and secure additional research funding. Information technology departments, libraries and research offices are being tasked with the triple role of developing infrastructure, introducing new services, and raising researchers’ awareness and skill levels in the uptake of these services and related eResearch concepts in order to achieve institutional goals. The purpose of this poster is to provide an overview of the coordinated approach to the provision of research skills workshops and seminars provided to researchers and higher degree research (HDR) students at QUT. Seminars and workshops are provided by the Library in collaboration with High Performance Computing and Research Support (HPC) and the Research Students Centre. The sessions are findable and bookable via the Library’s KickStart system. A list of session topics is provided. The Research Support services web site brings together information on a range of research support services provided by the Library and HPC. Seminars and workshops are also available via a research training calendar system into which all sessions are populated, regardless of the provider. The Library and HPC are also undertaking a train the trainer program.

Modification and validation of a microwave-assisted digestion method for subsequent ICP-MS determination of selected heavy metals in sediment and fish samples in Agusan River, Philippines

This study investigated, validated, and applied the optimum conditions for a modified microwave assisted digestion method for subsequent ICP-MS determination of mercury, cadmium, and lead in two matrices relevant to water quality, that is, sediment and fish. Three different combinations of power, pressure, and time conditions for microwave-assisted digestion were tested, using two certified reference materials representing the two matrices, to determine the optimum set of conditions. Validation of the optimized method indicated better recovery of the studied metals compared to standard methods. The validated method was applied to sediment and fish samples collected from Agusan River and one of its tributaries, located in Eastern Mindanao, Philippines. The metal concentrations in sediment ranged from 2.85 to 341.06 mg/kg for Hg, 0.05 to 44.46 mg/kg for Cd and 2.20 to 1256.16 mg/kg for Pb. The results indicate that the concentrations of these metals in the sediments rapidly decrease with distance downstream from sites of contamination. In the selected fish species, the metals were detected but at levels that are considered safe for human consumption, with concentrations of 2.14 to 6.82 μg/kg for Hg, 0.035 to 0.068 μg/kg for Cd, and 0.019 to 0.529 μg/kg for Pb.

AITPM national newsletter October 2008 president's report

It’s a pleasure for me to be penning my first President’s Message for the AITPM Newsletter. I am eagerly looking forward to serving the Institute and members over the coming couple of years. First though, I’d like to congratulate Andrew Hulse for steering the good ship AITPM over the past two years, bringing so many initiatives to the fore, including the Certified Transport Planner (CTP), stronger ties with other organisations and agencies such as IPENZ and Austroads, mutually beneficial sponsorship arrangements, and sharing his enthusiasm towards the Thunderbirds. Personally and largely thanks to my kids’ domination of the TV I’m a bit keener on the other great British sixties sci-fi classic, Doctor Who. Maybe we can generate a “favourite Doctor” dialogue in the Newsletter.

Developing an intimate ''relationship'' with nature through extreme sports participation

This article explores the interplay between extreme sports and the natural world in which they take place. Prior theoretical work on extreme sports has often made anthropocentric assumptions about this relationship, taking for granted that extreme participants treat nature only as a resource for athletic consumption, valuable only for its human uses. From this perspective, the natural world is regarded as a playground or battlefield, as a means to test physical prowess and human capacity. In contrast, extreme sports participants involved in this study report developing an intimate and reciprocal relationship with the natural world. A phenomenological analysis of participant accounts reveals, among veteran extreme athletes, the development of a heightened respect for something greater than themselves and a realization that humanity is simply a part of the natural environment.

Self-reported driving difficulty by persons with Hemianopia and Quadrantanopia

Purpose: To compare self-reported driving difficulty by persons with hemianopic or quadrantanopic field loss with that reported by age-matched drivers with normal visual fields; and to examine how their self- reported driving difficulty compares to ratings of driving performance provided by a certified driving rehabilitation specialist(CDRS). Method: Participants were 17 persons with hemianopic field loss, 7 with quadrantanopic loss, and 24 age-matched controls with normal visual fields, all of whom had current drivers’ licenses. Information was collected via questionnaire regarding driving difficulties experienced in 21 typical driving situations grouped into 3 categories(involvement of peripheral vision, low visibility conditions, and independent mobility). On-road driving performance was evaluated by a CDRS using a standard assessment scale. Results: Drivers with hemianopic and quadrantanopic field loss expressed significantly more difficulty with driving maneuvers involving peripheral vision and independent mobility, compared to those with normal visual fields. Drivers with hemianopia and quadrantanopia who were rated as unsafe to drive based upon an on-road assessment by the CDRS were no more likely to report driving difficulty than those rated as safe. Conclusion: This study highlights aspects of driving that hemianopic or quadrantanopic persons find particularly problematic, thus suggesting areas that could be focused on driving rehabilitation. Some drivers with hemianopia or quadrantanopia may inappropriately view themselves as good drivers when in fact their driving performance is unsafe as judged by a driving professional.

Exploring the process of implementing a smoking cessation intervention in pregnancy training program for midwives

The question of how to implement evidence effectively reveals a deficiency in our knowledge and understanding of the compound factors involved in such a process (Kitson, Rycroft-Malone et al. 2008). Although there is some awareness of the complexities of the process, there has been little exploration of the effectiveness of implementing evidence-based programs in health care. Despite public awareness of the dangers of smoking in pregnancy, and widespread public health measures to prevent smoking-related disease, women still continue to smoke in pregnancy (Ananth, Savitz et al. 1997; Laws and Hilder 2008). Evaluation of public health measures concludes that smoking cessation interventions during pregnancy increase quit rates among pregnant women (Melvin, Dolan-Mullen et al. 2000; Albrecht, Maloni et al. 2004; Lumley, Oliver et al. 2007). Notwithstanding the potential for improvement in health outcomes for pregnant women and their unborn babies, smoking interventions are often conducted poorly or not at all. Although midwives understand why women smoke in pregnancy and parenthood and are aware of the risks of smoking to both the pregnancy and the unborn child, they require specific knowledge and skills in the provision of support and advice on smoking for pregnant women (Bull and Whitehead 2006) . Organisational-change research demonstrates the complexity of the process of planned change in professionalised institutions such as health care (Greenhalgh, Robert et al. 2005). Some innovations and interventions are never accepted, and others are poorly supported (Greenhalgh, Robert et al. 2004). Comprehension of the change process around health promotion is crucial to the implementation of new health promotion interventions within health care (Riley, Taylor et al. 2003). This study utilised a case study approach to explore the process of implementing a smoking cessation training program for midwives in Queensland metropolitan and regional clinical areas, who attended a ‘Train-the-Trainer program’. The study draws on the organisational change work of Greenhalgh et al (2004) as the theoretical framework through which situational and structural factors are explored and examined as they inform the implementation of smoking cessation programs. The research data constituted staged interviews with midwives who instituted training programs for midwives, as well as organisational and policy documentation. Analysis of the data identified some areas that were not fully addressed in the theoretical model; these formed the basis of the Discussion and Implications for Future Research.

Understanding the diversity of non-specialised units within Australian property degrees

Building on the recommendations of the Bradley Review (2008), the Australian Federal government intends to promote a higher level of penetration of tertiary qualification across the broader Australian community which is anticipated to result in increased levels of standardisation across university degrees. In the field of property, tertiary academic programs are very closely aligned to the needs of a range of built environment professions and there are well developed synergies between the relevant professional bodies and the educational institutions. The strong nexus between the academic and the professional content is characterised by ongoing industry accreditation which nominates a range of outcomes which the academic programs must maintain across a range of specified metrics. Commonly, the accrediting bodies focus on standard of minimum requirements especially in the area of specialised subject areas where they require property graduates to demonstrate appropriate learning and attitudes. In addition to nominated content fields, in every undergraduate degree program there are also many other subjects which provide a richer experience for the students beyond the merely professional. This study focuses on the nonspecialised knowledge field which varies across the universities offering property degree courses as every university has the freedom to pursue its own policy for these non-specialised units. With universities being sensitive to their role of in the appropriate socialisation of new entrants, first year units have been used as a vehicle to support students’ transition into university education and the final year units seek to support students’ integration into the professional world. Consequentially, many property programs have to squeeze their property-specific units to accommodate more generic units for both first year and final year units and the resulting diversity is a feature of the current range of property degrees across Australia which this research will investigate. The matrix of knowledge fields nominated by the Australian Property Institute for accreditation of degrees accepted for Certified Practising Valuer (CPV) educational requirement and the complementary requirements of the other major accrediting body (RICS) are used to classify and compare similarities and differences across property degrees in the light of the streamlining anticipated from the Bradley Review.

Effect of cold water immersion on repeated cycling performance and limb blood flow

The purpose of the present study was to compare the effects of cold water immersion (CWI) and active recovery (ACT) on resting limb blood flow, rectal temperature and repeated cycling performance in the heat. Ten subjects completed two testing sessions separated by 1 week; each trial consisted of an initial all-out 35-min exercise bout, one of two 15-min recovery interventions (randomised: CWI or ACT), followed by a 40-min passive recovery period before repeating the 35-min exercise bout. Performance was measured as the change in total work completed during the exercise bouts. Resting limb blood flow, heart rate, rectal temperature and blood lactate were recorded throughout the testing sessions. There was a significant decline in performance after ACT (mean (SD) −1.81% (1.05%)) compared with CWI where performance remained unchanged (0.10% (0.71%)). Rectal temperature was reduced after CWI (36.8°C (1.0°C)) compared with ACT (38.3°C (0.4°C)), as was blood flow to the arms (CWI 3.64 (1.47) ml/100 ml/min; ACT 16.85 (3.57) ml/100 ml/min) and legs (CW 4.83 (2.49) ml/100 ml/min; ACT 4.83 (2.49) ml/100 ml/min). Leg blood flow at the end of the second exercise bout was not different between the active (15.25 (4.33) ml/100 ml/min) and cold trials (14.99 (4.96) ml/100 ml/min), whereas rectal temperature (CWI 38.1°C (0.3°C); ACT 38.8°C (0.2°C)) and arm blood flow (CWI 20.55 (3.78) ml/100 ml/min; ACT 23.83 (5.32) ml/100 ml/min) remained depressed until the end of the cold trial. These findings indicate that CWI is an effective intervention for maintaining repeat cycling performance in the heat and this performance benefit is associated with alterations in core temperature and limb blood flow.

Experiences in training ICD-10 trainers

The National Centre for Health Information Research & Training (formerly NCCH Brisbane) has been conducting an annual introductory ICD-10 coding program in Brisbane for seven years. In 2008, the Centre introduced a new initiative, inviting potential trainers to participate in a one week train the trainer workshop prior to the regular coder training. The new trainers are provided with the opportunity to practice their new skills with the support and assistance of the NCHIRT trainers during the subsequent introductory program. This paper will report on the results of a survey of participants of these programs about their experiences conducting training courses in their own countries. The train the trainer program as a means to create a cadre of trainers to support the implementation of ICD-11 will be explored.

Quality management system and construction performance

This paper discusses the level of effectiveness of quality principles and quality management system implementation and the relationship with performance of ISO9000 certified Indonesian contractors. It also discusses the statistical relationship between quality management systems (QMSs) and key performance indicators (KPIs) amongst a large sample of Indonesian construction companies. Data collected is from questionnaire surveys involving Quality Managers, Managers, and Project and Site Engineers representing 77 different companies. Results indicate that even though some contractors have not yet effectively implemented an effective QMS, most of the KPIs of respondent companies are still at the level of high performance. The statistical results show that the relationship between variables of ISO9000 QMS principles and contractors’ KPIs is significant. These results suggest that an increment in the implementation level of QMS principles can increase KPIs, however that much effort is still required for Indonesian contractors to fully effectively implement QMS principles and thus substantially improve performance against KPIs.