936 resultados para Center of Occupational Activities
Resumo:
The exposure to dust and polynuclear aromatic hydrocarbons (PAH) of 15 truck drivers from Geneva, Switzerland, was measured. The drivers were divided between "long-distance" drivers and "local" drivers and between smokers and nonsmokers and were compared with a control group of 6 office workers who were also divided into smokers and nonsmokers. Dust was measured on 1 workday both by a direct-reading instrument and by sampling. The local drivers showed higher exposure to dust (0.3 mg/m3) and PAH than the long-distance drivers (0.1 mg/m3), who showed no difference with the control group. This observation may be due to the fact that the local drivers spend more time in more polluted areas, such as streets with heavy traffic and construction sites, than do the long-distance drivers. Smoking does not influence exposure to dust and PAH of professional truck drivers, as measured in this study, probably because the ventilation rate of the truck cabins is relatively high even during cold days (11-15 r/h). The distribution of dust concentrations was shown in some cases to be quite different from the expected log-normal distribution. The contribution of diesel exhaust to these exposures could not be estimated since no specific tracer was used. However, the relatively low level of dust exposure dose not support the hypothesis that present day levels of diesel exhaust particulates play a significant role in the excess occurrence of lung cancer observed in professional truck drivers.
Resumo:
Excessive exposure to solar UV light is the main cause of skin cancers in humans. UV exposure depends on environmental as well as individual factors related to activity. Although outdoor occupational activities contribute significantly to the individual dose received, data on effective exposure are scarce and limited to a few occupations. A study was undertaken in order to assess effective short-term exposure among building workers and characterize the influence of individual and local factors on exposure. The effective exposure of construction workers in a mountainous area in the southern part of Switzerland was investigated through short-term dosimetry (97 dosimeters). Three altitudes, of about 500, 1500 and 2500 m were considered. Individual measurements over 20 working periods were performed using Spore film dosimeters on five body locations. The postural activity of workers was concomitantly recorded and static UV measurements were also performed. Effective exposure among building workers was high and exceeded occupational recommendations, for all individuals for at least one body location. The mean daily UV dose in plain was 11.9 SED (0.0-31.3 SED), in middle mountain 21.4 SED (6.6-46.8 SED) and in high mountain 28.6 SED (0.0-91.1 SED). Measured doses between workers and anatomical locations exhibited a high variability, stressing the role of local exposure conditions and individual factors. Short-term effective exposure ranged between 0 and 200% of ambient irradiation, indicating the occurrence of intense, subacute exposures. A predictive irradiation model was developed to investigate the role of individual factors. Posture and orientation were found to account for at least 38% of the total variance of relative individual exposure, and were also found to account more than altitude on the total variance of effective daily exposures. Targeted sensitization actions through professional information channels and specific prevention messages are recommended. Altitude outdoor workers should also benefit from preventive medical examination.
Resumo:
Background: Although the proportion of women in medicine is growing, female physicians continue to be disadvantaged in professional activities. The purpose of the study was to determine and compare the professional activities of female and male primary care physicians in Andalusia and to assess the effect of the health center on the performance of these activities. Methods: Descriptive, cross-sectional, and multicenter study. Setting: Spain. Participants: Population: urban health centers and their physicians. Sample: 88 health centers and 500 physicians. Independent variable: gender. Measurements: Control variables: age, postgraduate family medicine specialty (FMS), patient quota, patients/day, hours/day housework from Monday to Friday, idem weekend, people at home with special care, and family situation. Dependent variables: 24 professional activities in management, teaching, research, and the scientific community. Self-administered questionnaire. Descriptive, bivariate, and multilevel logistic regression analyses. Results: Response: 73.6%. Female physicians: 50.8%. Age: female physicians, 49.1 ± 4.3 yrs; male physicians, 51.3 ± 4.9 yrs (p < 0.001). Female physicians with FMS: 44.2%, male physicians with FMS: 33.3% (p < 0.001). Female physicians dedicated more hours to housework and more frequently lived alone versus male physicians. There were no differences in healthcare variables. Thirteen of the studied activities were less frequently performed by female physicians, indicating their lesser visibility in the production and diffusion of scientific knowledge. Performance of the majority of professional activities was independent of the health center in which the physician worked. Conclusions: There are gender inequities in the development of professional activities in urban health centers in Andalusia, even after controlling for family responsibilities, work load, and the effect of the health center, which was important in only a few of the activities under study.
Resumo:
OBJECTIVE: To evaluate the contributions of autophagic, necrotic, and apoptotic cell death mechanisms after neonatal cerebral ischemia and hence define the most appropriate neuroprotective approach for postischemic therapy. METHODS: Rats were exposed to transient focal cerebral ischemia on postnatal day 12. Some rats were treated by postischemic administration of pan-caspase or autophagy inhibitors. The ischemic brain tissue was studied histologically, biochemically, and ultrastructurally for autophagic, apoptotic, and necrotic markers. RESULTS: Lysosomal and autophagic activities were increased in neurons in the ischemic area from 6 to 24 hours postinjury, as shown by immunohistochemistry against lysosomal-associated membrane protein 1 and cathepsin D, by acid phosphatase histochemistry, by increased expression of autophagosome-specific LC3-II and by punctate LC3 staining. Electron microscopy confirmed the presence of large autolysosomes and putative autophagosomes in neurons. The increases in lysosomal activity and autophagosome formation together demonstrate increased autophagy, which occurred mainly in the border of the lesion, suggesting its involvement in delayed cell death. We also provide evidence for necrosis near the center of the lesion and apoptotic-like cell death in its border, but in nonautophagic cells. Postischemic intracerebroventricular injections of autophagy inhibitor 3-methyladenine strongly reduced the lesion volume (by 46%) even when given >4 hours after the beginning of the ischemia, whereas pan-caspase inhibitors, carbobenzoxy-valyl-alanyl-aspartyl(OMe)-fluoromethylketone and quinoline-val-asp(OMe)-Ch2-O-phenoxy, provided no protection. INTERPRETATION: The prominence of autophagic neuronal death in the ischemic penumbra and the neuroprotective efficacy of postischemic autophagy inhibition indicate that autophagy should be a primary target in the treatment of neonatal cerebral ischemia.
Resumo:
The purpose of this study was to assess the relationship between blood pressure (BP) levels and physical activity (PA) domains accounting for overweight/obesity. Adolescents aged 10 to 17 years old were recruited (n = 1021). International Obesity Task Force (IOTF) criteria were used to define overweight and obesity. High BP was defined using the Center of Disease Control and Prevention criteria. Different domains of PA (school activities, sport out of school, and leisure time PA) were assessed using a validated questionnaire. The prevalence of overweight/obesity was 21.9% for boys and 14.8% for girls. Some 13.4% of boys and 10.2% of girls, respectively, had high blood pressure (HBP). A strong and positive association was found between overweight and HBP. After adjustment for body mass index (BMI), total PA was inversely associated with BP. When all PA domains were entered simultaneously in a regression model, and after adjustment for BMI, only sport out of school was significantly and inversely associated with systolic BP [β: -0.82 (-1.50; -0.13)]. These findings open avenue for the early prevention of HBP by the prevention of obesity and promotion of PA.
Resumo:
We investigated the activities of fluconazole, caspofungin, anidulafungin, and amphotericin B against Candida species in planktonic form and biofilms using a highly sensitive assay measuring growth-related heat production (microcalorimetry). C. albicans, C. glabrata, C. krusei, and C. parapsilosis were tested, and MICs were determined by the broth microdilution method. The antifungal activities were determined by isothermal microcalorimetry at 37°C in RPMI 1640. For planktonic Candida, heat flow was measured in the presence of antifungal dilutions for 24 h. Candida biofilm was formed on porous glass beads for 24 h and exposed to serial dilutions of antifungals for 24 h, and heat flow was measured for 48 h. The minimum heat inhibitory concentration (MHIC) was defined as the lowest antifungal concentration reducing the heat flow peak by ≥50% (≥90% for amphotericin B) at 24 h for planktonic Candida and at 48 h for Candida biofilms (measured also at 24 h). Fluconazole (planktonic MHICs, 0.25 to >512 μg/ml) and amphotericin B (planktonic MHICs, 0.25 to 1 μg/ml) showed higher MHICs than anidulafungin (planktonic MHICs, 0.015 to 0.5 μg/ml) and caspofungin (planktonic MHICs, 0.125 to 0.5 μg/ml). Against Candida species in biofilms, fluconazole's activity was reduced by >1,000-fold compared to its activity against the planktonic counterparts, whereas echinocandins and amphotericin B mainly preserved their activities. Fluconazole induced growth of planktonic C. krusei at sub-MICs. At high concentrations of caspofungin (>4 μg/ml), paradoxical growth of planktonic C. albicans and C. glabrata was observed. Microcalorimetry enabled real-time evaluation of antifungal activities against planktonic and biofilm Candida organisms. It can be used in the future to evaluate new antifungals and antifungal combinations and to study resistant strains.
Resumo:
We report here the legislative issues related toembryo research and human embryonic stem cell (hESC)research in Spain and the derivation of nine hESC lines atthe Center of Regenerative Medicine in Barcelona. You canfind the information for obtaining our lines for researchpurposes at blc@cmrb.eu.
Resumo:
This doctoral thesis deals with the rise and potential fall of achievement career as an institutional biographical pattern. I start with the assumption that the achievement career, as a result of the spread of large-scale bureaucratic companies, the male-breadwinner family model, and meritocratic ideals, came to life in the first half of the twentieth century. During the so-called 30 glorieuses, it became even a normatively dominant and also politically significant male biographical pattern. But the structural changes that announced the end of the post-war golden age seemed also to threaten and-according to certain scholars-erode this type of occupational trajectory. In order to understand this dynamic I will try to reconstruct the achievement career in Switzerland empirically. I examine (1) the structural changes of the economic field from 1970 to 2000, (2) the transformations of the trajectories during this period, and (3) ways in which the concerned individuals interpret and react to these changes.
Resumo:
Skin exposures to chemicals may lead, through percutaneous permeation, to a significant increase in systemic circulation. Skin is the primary route of entry during some occupational activities, especially in agriculture. To reduce skin exposures, the use of personal protective equipment (PPE) is recommended. PPE efficiency is characterized as the time until products permeate through material (lag time, Tlag). Both skin and PPE permeations are assessed using similar in vitro methods; the diffusion cell system. Flow-through diffusion cells were used in this study to assess the permeation of two herbicides, bentazon and isoproturon, as well as four related commercial formulations (Basagran(®), Basamais(®), Arelon(®) and Matara(®)). Permeation was measured through fresh excised human skin, protective clothing suits (suits) (Microchem(®) 3000, AgriSafe Pro(®), Proshield(®) and Microgard(®) 2000 Plus Green), and a combination of skin and suits. Both herbicides, tested by itself or as an active ingredient in formulations, permeated readily through human skin and tested suits (Tlag < 2 h). High permeation coefficients were obtained regardless of formulations or tested membranes, except for Microchem(®) 3000. Short Tlag, were observed even when skin was covered with suits, except for Microchem(®) 3000. Kp values tended to decrease when suits covered the skin (except when Arelon(®) was applied to skin covered with AgriSafe Pro and Microgard(®) 2000), suggesting that Tlag alone is insufficient in characterizing suits. To better estimate human skin permeations, in vitro experiments should not only use human skin but also consider the intended use of the suit, i.e., the active ingredient concentrations and type of formulations, which significantly affect skin permeation.
Resumo:
A new method of measuring joint angle using a combination of accelerometers and gyroscopes is presented. The method proposes a minimal sensor configuration with one sensor module mounted on each segment. The model is based on estimating the acceleration of the joint center of rotation by placing a pair of virtual sensors on the adjacent segments at the center of rotation. In the proposed technique, joint angles are found without the need for integration, so absolute angles can be obtained which are free from any source of drift. The model considers anatomical aspects and is personalized for each subject prior to each measurement. The method was validated by measuring knee flexion-extension angles of eight subjects, walking at three different speeds, and comparing the results with a reference motion measurement system. The results are very close to those of the reference system presenting very small errors (rms = 1.3, mean = 0.2, SD = 1.1 deg) and excellent correlation coefficients (0.997). The algorithm is able to provide joint angles in real-time, and ready for use in gait analysis. Technically, the system is portable, easily mountable, and can be used for long term monitoring without hindrance to natural activities.
Resumo:
In this study, we assessed the mixed exposure of highway maintenance workers to airborne particles, noise, and gaseous co-pollutants. The aim was to provide a better understanding of the workers' exposure to facilitate the evaluation of short-term effects on cardiovascular health endpoints. To quantify the workers' exposure, we monitored 18 subjects during 50 non-consecutive work shifts. Exposure assessment was based on personal and work site measurements and included fine particulate matter (PM2.5), particle number concentration (PNC), noise (Leq), and the gaseous co-pollutants: carbon monoxide, nitrogen dioxide, and ozone. Mean work shift PM2.5 concentrations (gravimetric measurements) ranged from 20.3 to 321 μg m(-3) (mean 62 μg m(-3)) and PNC were between 1.6×10(4) and 4.1×10(5) particles cm(-3) (8.9×10(4) particles cm(-3)). Noise levels were generally high with Leq over work shifts from 73.3 to 96.0 dB(A); the averaged Leq over all work shifts was 87.2 dB(A). The highest exposure to fine and ultrafine particles was measured during grass mowing and lumbering when motorized brush cutters and chain saws were used. Highest noise levels, caused by pneumatic hammers, were measured during paving and guardrail repair. We found moderate Spearman correlations between PNC and PM2.5 (r = 0.56); PNC, PM2.5, and CO (r = 0.60 and r = 0.50) as well as PNC and noise (r = 0.50). Variability and correlation of parameters were influenced by work activities that included equipment causing combined air pollutant and noise emissions (e.g. brush cutters and chain saws). We conclude that highway maintenance workers are frequently exposed to elevated airborne particle and noise levels compared with the average population. This elevated exposure is a consequence of the permanent proximity to highway traffic with additional peak exposures caused by emissions of the work-related equipment.
Resumo:
The inability to characterize more precisely the extent of occupational diseases limits the implementation of an effective preventive policy. Furthermore, not all work-related conditions are reported by the Swiss workers' compensation system. A seven-year (1986 to 1992) retrospective study of medical visits in an Institute of Occupational Health Sciences is presented. The objective of this study is to expand data on occupational diseases for clinical and public health intervention. 298 patients have been examined for a possible work-related condition. In 140 cases (47%), an occupational disease according to the Swiss Law was found. Respiratory tract was the main target of industrial pollutants. Respiratory irritation , solvent intoxications, contact dermatitis and asthma were the most frequent conditions seen. 97 workplace visits (32% of all medical visits) were necessary for diagnostic purposes. Painters (construction, cars) and other solvent exposed workers were at particular risk. Rare alpha-1-antitrypsin phenotypes were found several times in workers with respiratory diseases confirming the value of this test in occupational medicine. Despite many referral biases, direct clinical and public health applications of the data are possible. This study confirms the hypothesis that occupational respiratory diseases and intoxications are probably underreported in the workers' compensation statistics. Activities with an increased risk of work-related diseases have been identified so workplace intervention could be highly targeted. This study shows also that a more intense collaboration between primary care physicians, hospital services and occupational medical specialists is necessary to improve clinical and epidemiological surveillance of work-related health conditions.
Resumo:
Despite numerous discussions, workshops, reviews and reports about responsible development of nanotechnology, information describing health and environmental risk of engineered nanoparticles or nanomaterials is severely lacking and thus insufficient for completing rigorous risk assessment on their use. However, since preliminary scientific evaluations indicate that there are reasonable suspicions that activities involving nanomaterials might have damaging effects on human health; the precautionary principle must be applied. Public and private institutions as well as industries have the duty to adopt preventive and protective measures proportionate to the risk intensity and the desired level of protection. In this work, we present a practical, 'user-friendly' procedure for a university-wide safety and health management of nanomaterials, developed as a multi-stakeholder effort (government, accident insurance, researchers and experts for occupational safety and health). The process starts using a schematic decision tree that allows classifying the nano laboratory into three hazard classes similar to a control banding approach (from Nano 3 - highest hazard to Nano1 - lowest hazard). Classifying laboratories into risk classes would require considering actual or potential exposure to the nanomaterial as well as statistical data on health effects of exposure. Due to the fact that these data (as well as exposure limits for each individual material) are not available, risk classes could not be determined. For each hazard level we then provide a list of required risk mitigation measures (technical, organizational and personal). The target 'users' of this safety and health methodology are researchers and safety officers. They can rapidly access the precautionary hazard class of their activities and the corresponding adequate safety and health measures. We succeed in convincing scientist dealing with nano-activities that adequate safety measures and management are promoting innovation and discoveries by ensuring them a safe environment even in the case of very novel products. The proposed measures are not considered as constraints but as a support to their research. This methodology is being implemented at the Ecole Polytechnique de Lausanne in over 100 research labs dealing with nanomaterials. It is our opinion that it would be useful to other research and academia institutions as well. [Authors]
Resumo:
Introduction Functional subjective evaluation through questionnaire is fundamental, but not often realized in patients with back complaints, lacking validated tools. The Spinal Function Sort (SFS) was only validated in English. We aimed to translate, adapt and validate the French (SFS-F) and German (SFS-G) versions of the SFS. Methods Three hundred and forty-four patients, experiencing various back complaints, were recruited in a French (n = 87) and a German-speaking (n = 257) center. Construct validity was estimated via correlations with SF-36 physical and mental scales, pain intensity and hospital anxiety and depression scales (HADS). Scale homogeneities were assessed by Cronbach's α. Test-retest reliability was assessed on 65 additional patients using intraclass correlation (IC). Results For the French and German translations, respectively, α were 0.98 and 0.98; IC 0.98 (95% CI: [0.97; 1.00]) and 0.94 (0.90; 0.98). Correlations with physical functioning were 0.63 (0.48; 0.74) and 0.67 (0.59; 0.73); with physical summary 0.60 (0.44; 0.72) and 0.52 (0.43; 0.61); with pain -0.33 (-0.51; -0.13) and -0.51 (-0.60; -0.42); with mental health -0.08 (-0.29; 0.14) and 0.25 (0.13; 0.36); with mental summary 0.01 (-0.21; 0.23) and 0.28 (0.16; 0.39); with depression -0.26 (-0.45; -0.05) and -0.42 (-0.52; -0.32); with anxiety -0.17 (-0.37; -0.04) and -0.45 (-0.54; -0.35). Conclusions Reliability was excellent for both languages. Convergent validity was good with SF-36 physical scales, moderate with VAS pain. Divergent validity was low with SF-36 mental scales in both translated versions and with HADS for the SFS-F (moderate in SFS-G). Both versions seem to be valid and reliable for evaluating perceived functional capacity in patients with back complaints.
Resumo:
Introduction: Beryllium (Be) is increasingly used in various industrial applications. Occupational exposure to Be may lead to chronic beryllium disease (CBD), a pulmonary granulomatous disorder closely similar to sarcoidosis, which develop in 1 to 15% of exposed workers. Although Switzerland is one of the major Be importers worldwide, little information is available about occurrence of exposure and the number of workers exposed in this country. Objectives: 1) evaluate the number of workers potentially exposed to Be in Switzerland; 2) construct a screening tool to allow potential Be exposure detection in a clinical setting. Methods: After identification of industrial sectors involving beryllium exposure based on expert reports and scientific literature, an estimation of the number of workers employed in these relevant industries was made using data from the Swiss federal population census and registries of economic activities. A second analysis was performed to estimate the fraction of workers really exposed to Be in each industrial sector. This adjustment was made according to the results of a French survey (INRS, Institut National de Recherche et de Sécurité) conducted by questionnaire addressed to 4500 companies in relevant industries on their use of beryllium and other issues such as percentage of employees really exposed. These realistic data were used to develop a self-administrated screening questionnaire allowed to identify patients with possible Be exposure. Results: In Switzerland, the number of workers employed in industries using Be was nearly 150 000. The estimated number of workers exposed to beryllium in these industries ranged from 2000 to 4000. Relevant sectors were: microengineering, precision turning, watchmaking and metal waste treatment and recycling. The validation of the self-administrated questionnaire containing a list of jobs and leisure activities associated with potential Be exposure is in progress within the framework of a national study. Conclusions: The number of workers potentially exposed to Be in Switzerland is rather high compared to estimations for other industrialized countries and might constitute an underestimated occupational health problem. Undetected Be exposure in patients with sarcoidosis may occur and result in misdiagnosis. Once validated, the self-administrated questionnaire could be used by clinicians to screen for Be exposure in patients with granulomatous lung disorders.