3μm GaInNAs/GasAs Quantum Well Resonant Cavity Enhanced Photodetector

A 1.3μm GaInNAs resonant cavity enhanced (RCE) photodetector (PD) has been grown by molecular beam epitaxy (MBE) monolithically on (100) GaAs substrate using a home-made ion-removed dc-plasma cell as nitrogen source. A transfer matrix method was used to optimize the device structure. The absorption region is composed of three GaInNAs quantum wells separated by GaAs layers. Devices were isolated by etching 130μm-diameter mesas and filling polyamide into grooves. The maximal quantum efficiency of the device is about 12% at 1.293μm. Full width at half maximum (FWHM) is 5.8nm and 3dB bandwidth is 304MHz. Dark current is 2 * 10~(-11) A at zero bias voltage. Further improvement of the performance of the RCE PD can be obtained by optimizing of the structure design and MBE growth conditions.

Using photoluminescence as optimization criterion to achieve high-quality InGaAs/AlGaAs pHEMT structure

The single delta -doped InGaAs/AlGaAs pseudomorphic HEMT structure materials were grown by molecular beam epitaxy. The photoluminescence spectra of the materials were studied. There are two peaks in the photoluminescence spectra of the materials, corresponding to two sub energy levels of InGaAs quantum well. The ratio of the two peak's intensity was used as criterion to optimize the layer structures of the materials. The material with optimized layer ;tructures exhibits the 77 It mobility and two-dimensional electron gas density of 16 500 cm(2)/Vs and 2.58 x 10(12) cm(-2) respectively, and the 300 K mobility and two-dimensional electron gas density of 6800 cm(2)/Vs and 2.55 x 10(12) cm(-2) respectively. The pseudomorphic HEMT devices with gate length of 0.2 mum were fabricated using this material. The maximum transconductance of 650 mS/mm and the cut-off frequency of 81 GHz were achieved. (C) 2001 Elsevier Science B.V. All rights reserved.

应用负载型纳米铁去除饮用水中砷的研究

砷是毒性最强的元素之一，水体中砷的污染己经引起人们广泛的关注。我国的新疆、内蒙、山西和台湾等省和地区地下水砷含量严重超标。全球共有5,000多万人遭受高砷饮用水的威胁，其中中国有1,500多万，是饮用水砷污染最严重的国家之一。WHO推荐饮用水砷的最高允许浓度从原来的50 µg•L-1已降至10 µg•L-1。更为严格的砷卫生标准的颁布，对作为饮用水源的地下水中的砷去除工艺提出了更高的要求。吸附法除砷比膜法、混凝法和离子交换法更安全、简便，是砷去除工艺中最有效的方法之一。 首先，本研究通过优化制备条件（包括炭种类的选择、炭的粒径大小、还原剂的浓度及滴定速率、反应温度、铁盐的种类及浓度、分散剂的比例及浓度），制备了负载型纳米铁。考虑到砷的去除效率、工程应用的可行性以及经济性，最优的制备条件如下：选用粒径为20~40目煤质炭，在室温、一定的分散剂比例及浓度，0.2 M KBH4滴速为20 d•min-1时所制备的Fe/炭为82.0 mg•g-1；纳米铁在活性炭孔内呈针状，其直径为30~500 nm，长度为1,000~2,000 nm。绝大多数的铁都负载到活性炭内部，这在处理水时铁不流失很重要。 其次，利用制备的负载型纳米铁作吸附载体，进行了饮用水中As(Ⅴ)的吸附去除实验。研究了该吸附剂对As(Ⅴ)的吸附等温线、动力学以及影响动力学的各种因素（包括As(Ⅴ)的不同初始浓度、吸附剂用量、pH值、共存离子和不同温度）、pH值、共存离子等环境条件对As(Ⅴ)去除的影响；以及吸附剂的再生及再生后的吸附效率等。研究发现在前12 h内吸附较快，72 h时达到了平衡。用Langmuir 吸附等温式估算出As(Ⅴ)的吸附量为12.0 mg•g-1。该吸附剂在pH 6.5， (25±2)℃， As(Ⅴ)初始浓度为2 mg•L-1，吸附剂用量为1.0 g•L-1时，As(Ⅴ)的去除率为75.2%；当把吸附剂的用量增加到1.5 g•L-1时，As(Ⅴ)的去除率可达99.9%以上。吸附剂可以用0.1M的NaOH浸泡12 h后即可再生，再生效率较高。常见的阴离子中PO43-、SiO32-对As(Ⅲ)的去除抑制较大，而SO42-、CO32-、C2O42-等离子对砷的去除影响较小。Fe2+对As(Ⅲ)的吸附抑制作用较大而其它阳离子影响不大。吸附剂可用0.1 M NaOH 有效再生，并且具有良好的机械性能。实验室初步实验数据表明，该吸附剂对饮用水除砷具有较好的应用前景。 第三，利用实验室制备的负载型纳米铁对饮用水中As(Ⅲ)的吸附去除也进行了研究。考察了吸附等温线、动力学以及影响动力学的各种因素、pH值、共存离子等环境条件对As(Ⅲ)去除的影响；以及吸附剂的再生及再生后的吸附效率等。研究发现，该吸附剂在pH 6.5， (25±2)℃， As(Ⅲ)初始浓度为2 mg•L-1，吸附剂用量为1.0 g•L-1时， 对As(Ⅲ)的去除率为99.8%；其吸附容量为1.996mg•g-1。吸附过程中部分As(Ⅲ)被氧化。与As(Ⅴ)的吸附相比，该吸附剂对As(Ⅲ)的效率比较高-而常见的其它除砷吸附剂如载铁纤维棉等，对As(Ⅴ)的效率比As(Ⅲ)高，为有效去除As(Ⅲ)，常常需要专门加上氧化这一过程。 最后，利用负载型纳米铁对饮用水中As(Ⅲ) 的氧化性能进行考察，发现该吸附剂不但能够有效吸附去除饮用水中的砷，而且还能把As(Ⅲ)有效地氧化为As(Ⅴ)。经过对吸附剂的构成组分分析发现，活性炭表面因富含多种官能团而对三价砷的氧化作用最大；其次是纳米铁也能把As(Ⅲ)氧化为As(Ⅴ)。

Performance of an improved logarithmic phase mask with optimized parameters in a wavefront-coding system

In two papers [Proc. SPIE 4471, 272-280 (2001) and Appl. Opt. 43, 2709-2721 (2004)], a logarithmic phase mask was proposed and proved to be effective in extending the depth of field; however, according to our research, this mask is not that perfect because the corresponding defocused modulation transfer function has large oscillations in the low-frequency region, even when the mask is optimized. So, in a previously published paper [Opt. Lett. 33, 1171-1173 (2008)], we proposed an improved logarithmic phase mask by making a small modification. The new mask can not only eliminate the drawbacks to a certain extent but can also be even less sensitive to focus errors according to Fisher information criteria. However, the performance comparison was carried out with the modified mask not being optimized, which was not reasonable. In this manuscript, we optimize the modified logarithmic phase mask first before analyzing its performance and more convincing results have been obtained based on the analysis of several frequently used metrics. (C) 2010 Optical Society of America

Interface delamination of the thermal barrier coating subjected to local heating

To investigate the possible failure modes of the thermal barrier coating (TBC) used to protect the scramjet combustion chamber, the local heating via laser beam irradiation was utilized to simulate the service condition of high thermal flux and high temperature gradient. Firstly, the experimental method and process were described and the typical fracture morphology of the TBC under test were provided. Then, the theoretical and finite element modeling were carried out to study the temperature, deformation and stresses of the specimen when the top ceramic coat was subjected to local heating, and to demonstrate the mechanism on the failure of the TBC. It is revealed that the interface delamination shall appear and ultimately lead to the failure of the TBC under such thermal loading of local quick heating. According to the outcome of this study, the driving force of the interface delamination is influenced greatly by the key structural parameters and performance matching. Moreover, by utilizing the rules of the effects of these parameters on the fracture driving force, there is some possibility for the designer to optimize the performances of the TBC.

高寒湿地自然保护区多核心动态分区研究——以四川若尔盖湿地国家级自然保护区为例

中国拥有92466 Km2的各类高原湿地，具有湿地退化、过度放牧等相似特征，保护与利用矛盾突出。高寒湿地保护区尽管在制度上以核心区、缓冲区来约束当地的放牧等外来干扰行为，但在实际管理中却不能起到应有的作用。 本研究以四川若尔盖湿地国家级自然保护区为例，应用3S技术，建立保护区多功能动态分区工作流模型，通过不同植被类型的识别和空间特征分析、不同动物类群在上述植被生境中的时空分布特征分析、保护区主要干扰因素的时空分布特征分析，突出对保护区主要保护对象（湿地生态系统）的保护，对保护区进行管理分区，依据野生动物利用特征和植被生长特征对核心区进行年周期动态利用，缓解保护与发展的矛盾，促进保护区的优化管理。 应用归一化植被指数（NDVI）与植被盖度的相关性，将归一化植被指数（NDVI）转化为植被盖度指数（MDVI），结合保护区牧场划分和时空利用特征专家经验，结果表明，MDVI值在1-139之间主要代表着水体、裸地、沙地等；MDVI140-256为草地和高山灌丛；MDVI210是当地夏牧场和秋冬牧场的划分区间值。 合理的区划需要资金、技术和政策的支持，为保证保护区多核心动态分区的实施，本研究提出了生态工程、牧业发展方式转变、湿地特色产业发展、湿地政策、社区参与和科技支撑等六大保障措施。 In China, 92466 Km2 highland or frigid wetlands are (were) facing major management problems, such as wetland degradation and overgazing. Conflict between conservation and utilization on those wetlands can be found anywhere today. Although many nature reserves have been setup for protection of frigid wetland, and core and buffer zone has been declared to forbid any kinds of disturbance, local farmers still use these areas for grazing. As an example by Sichuan Roige Wetlands National Nature Reserve(SRWNRR), we set up a 3S flow model to analyze the character of year-round distribution patters of vegetation, wildlife, and grazing. Combined and overlapped these characters together, we select multi-core zone and buffer zone, then define a dynamic management period in different zone to optimize protection wetland in the reserve. Normalized Difference Vegetation Index（NDVI）is highly related with coverage of vegetation. When convert NDVI to MDVI (coverage index, 1-256), index 139 and 210 can be as inflexion to distinguish among water/sand/bared land, summer pasture, and autumn / winter pasture. We use these to select different layers and analyze grazing pattern. To be more realistic, we put forward some strategies to support our multi-core and dynamic management of wetland in Roige, including ecological restoration engineering, changing of stock raising industry, changing of wetland policy, community based management and technology renovation supports.

白腐菌选择性降解木质素的研究

对15株白腐真菌进行了以玉米秸秆为基质的初步筛选，从中获得一株选择性系数较高的菌株Y10，并对其降解玉米秸秆的情况进行了研究。结果表明，在30天的培养过程中菌株Y10对玉米秸秆降解的选择性系数都大于1，第15天选择性系数最高为3.88。对未经降解和降解过的玉米秸秆分别作了紫外光谱和红外光谱分析，结果表明，经该菌降解后玉米秸秆的化学成分发生了很大变化，且木质素的降解程度要大于纤维素的降解程度。对菌株Y10进行了ITS-5.8S rDNA序列鉴定，初步判定其为Cerrena sp.。 为了考查不同的外源添加物对菌株Y10降解玉米秸秆的影响，在以玉米秸秆为基质的固态发酵培养基中分别添加了7种金属离子、8种碳源、6种氮源。结果显示，这7种金属离子均能促进木质素的降解，并且一定浓度的某些离子明显抑制纤维素的降解；其中添加0.036%的MnSO4·H2O和0.36%的MgSO4·7H2O对纤维素降解的抑制作用比较强，降解率分别为0.96%和1.31%，木质素的选择性系数分别达到了34.40和20.17。8种碳源中除麦芽糖外都能促进木质素的降解，除微晶纤维素外都明显促进纤维素的降解。6种氮源中酒石酸铵、硫酸铵、草酸铵和氯化铵的添加都会使该菌生长变慢，而且氮源浓度越高菌丝生长越慢。外加碳源和金属离子对半纤维素降解和选择性系数的影响不大。 同时对菌株Y10在液态培养下产木质素降解酶的条件和培养基做了优化。结果表明，在初始产酶培养基中，菌株Y10的漆酶酶活在第10d达到最高，锰过氧化物酶酶活在第11d达到最高，基本上检测不到木质素过氧化物酶。菌株Y10产漆酶的最适温度为32℃，最适PH为6.0；产锰过氧化物酶的最适温度为32℃，最适PH为6.5。菌株Y10产漆酶的最佳碳源为甘露糖，最佳氮源为酒石酸铵，最适诱导剂VA浓度为3 mmol/L，最适表面活性剂TW-80浓度为1%。 利用响应面法对其产漆酶的培养基进行优化，优化后的培养基配方为葡萄糖10.00 g/L，酒石酸铵0.50 g/L，大量元素296.50 ml/L，微量元素100.00 ml/L，NTA 1.40 g/L，VA 5.00 mmol/L，吐温-80加入量为0.10%。进行了菌株Y10产漆酶的验证实验，实测酶活为5282.56 U/L，与预测酶活5162.73 U/L接近。在优化后培养基中，菌株Y10在第14 d达到生长的最高峰，第20 d时，漆酶酶活最高，为11325.00 U/L；第16 d时，锰过氧化物酶酶活最高，为30.77 U/L。 对菌株Y10的漆酶酶学性质做了初步的研究，结果显示，酶反应的最适温度为40℃-65℃，最适PH为3.0。在40℃，PH=3.0时，漆酶催化ABTS反应的米氏方程为 。 Fifteen white-rot fungi based on corn stalk were screened. One white-rot fungus Y10 with high selectivity value was obtained. The degradation of corn stalk was initially studied. The results indicated that the selectivity value was above 1 during the 30 day-cultivation and the highest was 3.88 after 15 days. The composition of untreated and treated stalk was analyzed through ultraviolet spectroscopy and infrared spectroscopy. It was found that the composition of treated stalk was greatly altered and the degree of the degradation of lignin is greater than the cellulose. Y10 was identified as Cerrena sp. by ITS -5.8S rDNA sequence analysis. The influence of metal ions, carbon sources and nitrogen sources on corn stalk degradation by white-rot fungus was studied. While all seven metal ions could promote lignin degradation, the cellulose degradation was best inhibited at certain ion concentrations. Notably, when 0.036% MnSO4·H2O and 0.36% MgSO4·7H2O were added into the medium, the cellulose degradation was restrained to the extents that the coefficients of lignin selectivity rose to 34.40 and 20.17 respectively. It was also found that all carbon sources except maltose can promote lignin degradation. The addition of carbon sources other than microcrystalline cellulose significantly promoted cellulose degradation. The addition of the nitrogen sources, ammonium tartrate, ammonium sulfate, oxalate, ammonium chloride, resulted in remarkable inhibition to mycelium growth; the larger the concentrations of nitrogen sources are, the slower the mycelium grew. The addition of carbon sources and metal ions had less impact on the degradation of hemicellulose and selectivity value. Meanwhile, we optimized the conditions and culture medium of the lignin-degrading enzyme production of strain Y10. The results showed that in the initial culture medium, the Lac activity was highest at the 10th day, the MnP activity was highest at the 11th day and the LiP could not be detected. The optimum condition of Lac was at temperature 32 and PH =6.0 and the optimum condition of MnP was at temperature 32 and PH =6.5. The optimum carbon source for Lac was seminose, the optimum nitrogen source was ammonium tartrate, the optimum content of VA was 3 mmol/L, the optimum content of TW-80 was 1%. PB and RSM were used to optimize the culture medium of laccase by white-rot fungus Y10. The optimum culture medium was consist of glucose 10.00 g/L, ammonium tartrate 0.50 g/L, macro elements 296.50 ml/L, trace elements 100.00 ml/L, NTA 1.40 g/L, VA 5.00 mmol/L, TW-80 0.10%. Under the optimal conditions, the activity of laccase was 5282.56 U/L and the experimental value agreed with the predicted value 5162.73 U/L. The biomass was highest at the 14th day, the Lac activity was highest at the 20th day, the MnP activity was highest at the 16th day. The results of the studies on the characteristics of Lac showed that the optimum temperature for Lac activity is 40℃-65℃ ; the optimum PH for Lac activity is 3.0 and under 40℃，PH=3.0, the Michaelis-menten equation of Lac catalized ABTS oxidation was .

厌氧产氢菌的分离筛选、诱变选育及其产氢特性的研究

本文从四川绵竹酒厂、成都市龙泉长安垃圾填埋场以及四川大学荷花池底的厌氧污泥中先后分离得到63株厌氧产氢菌，其中H-8、H-61、HC-10等16株产氢细菌产氢能力较高，HC-10的产氢能力最高，最大产氢量和最大产氢速率分别达到2840 ml H2/L培养基和25.39 mmol H2/g drycell·h，对HC-10进行生理生化鉴定和分子生物学鉴定，判定其为clostridium sp.，对HC-10的产氢条件进行了研究，结果表明，该菌的最适生长温度为35 ℃，最适生长初始pH为7，以葡萄糖为最佳碳源，以蛋白胨为最佳氮源，不利用无机氮源，其产氢发酵液相产物以乙醇和乙酸为主，其发酵类型属于乙醇型发酵。此外，以酒糟废液作为底物，进行了菌株HC-10的生物强化试验，研究表明，投加了HC-10的强化系统其产氢量比对照高出40.32%。 同时为了获得厌氧产氢菌的高效突变株，分别以产氢菌H-8和H-61为原始菌株进行微波诱变处理，对微波诱变参数进行了优化，考察了突变株的遗传稳定性、产氢特性及耐酸性。菌株H-8经过微波诱变得到5株高产氢突变株HW7、HW33、HW181、HW184、HW195，经多次传代表明HW195是稳定的高产突变株。突变株HW195具有较好的耐酸性，在pH值为2.8时仍能生长。通过间歇发酵实验，其最大产氢量和最大产氢速率分别达到2460 mL/L培养基和27.97 mmol H2/g drycell·h，比原始菌分别提高了50.75%和41.7%。菌株H-61经过微波诱变后选育得到的突变株HW-18，其最大产氢量和最大产氢速率分别达到2190 mL/L培养基和25.86 mmol H2/g drycell·h，比原始菌分别提高了23.03%和31.00%。 为了对比各种诱变方式对产氢菌产氢能力的影响，以厌氧产氢菌H-61为原始菌株，先后经亚硝基胍(NTG)、紫外(UV)诱变，选育得到1株高产突变株HCM-23。在葡萄糖浓度为10 g/L的条件下，其产氢量为3024 mL/L培养基，比原始菌株提高了69.89%；其最大产氢速率为33.19 mmol H2/g drycell·h，比原始菌株提高了68.14%。经过多次传代实验，稳定性良好。其发酵末端产物以乙醇和乙酸为主，属于典型乙醇型发酵。其最适产氢初始pH为6.5，最适生长温度为36 ℃，以蔗糖为最佳碳源。与原始菌株相比，突变株HCM-23的产氢特性发生了改变，如生长延滞期延长，可利用无机氮源等。 From anaerobic activated sludge, 16 strains of hydrogen producing bacteria were newly isolated. One of them named as HC-10 had the highest hydrogen producing capability, under the batch fermentative hydrogen production condition, the maximal hydrogen yield and hydrogen production rate was 2840 mL/L culture and 25.39 mmol H2/g drycell·h. It was identified as clostridium sp.HC-10 by 16S rDNA sequence analysis. Various parameters for hydrogen production, including substrates, initial pH and temperature, have been studied. The optimum condition for hydrogen producing of strain HC-10 were achieved as: initial pH 7.0, temperature 35 ℃, glucose as the favorite substrate, Moreover, using distiller's solubles wastewater as substrate, HC-10 strain was added in the biohydrogen producing system to research the bioaugmentation effection. The results showed that the hydrogen production of bioaugmentation system was 40.32% higher than the noaugmentation system. An anaerobic, hydrogen producing strain H-8 was irradiated by microwave to optimize the microwave mutagenesis condition, and to test the heredity, hydrogen-producing potential and aciduric of the mutants. An aciduric mutant named as HW195 with steady hydrogen-producing capability was obtained, which can grow at pH 2.8. Its capability of hydrogen production was tested in the batch culture experiments. The maximum hydrogen yield and hydrogen production rate was 2460 mL/L culture and 29.97 mmol H2/g drycell·h, which was 50.7% and 41.7% higher than those of the initial strain, respectively. When used the strain H-61 as original strain, a mutant named as HW18 was obtained. The maximum hydrogen yield and hydrogen production rate was 2190 mL/L culture and 25.86 mmol H2/g drycell·h, which was 23.03% and 31.00% higher than those of the initial strain, respectively. The results demonstrated that microwave mutagenesis could be used in the field of hydrogen producing microorganism. The hydrogen producing strain H-61 was used as an original strain which was induced by NTG and UV for increasing and the hydrogen production capability. One of the highest efficient H2-producing mutants was named as HCM-23 with its stable hydrogen production capability. which was tested in the batch culture experiments. With the condition of 10 g/L glucose, its cumulative hydrogen yield and hydrogen production rate was 3024 mL/L culture and 33.19 mmol H2/g drycell·h, 69.89％and 68.14％ higher than that of the original strain, respectively. The terminal liquid product compositions showed that the mutant HCM-23 fermentation was ethanol type, while the original strain H-61 fermentation was butyric acid type. Varieties of parameters of hydrogen production fermentation were studied, including time, carbon source, nitrogen source, glucose concentration, glucose utilization, initial pH and incubation temperature had been studied, indicated the optimum condition of hydrogen production for the mutant HCM-23 as initial pH6.5, temperature 36 ℃, and the favorite substrate was sucrose. The hydrogen production characters of the mutant and the original strain were different, such as, the growth lag phase and the utilization of inorganic nitrogen source, etc. This work shows a good application potential of NTG-UV combined mutation in the biohydrogen production. And the hydrogen production mechanism and metabolic pathway should be explored furthermore.

Design of the IMP microbeam irradiation system for 100 MeV/u heavy ions

Abstract A state-of-the-art high energy heavy ion microbeam irradiation system is constructed at the Institute of Modern Physics of the Chinese Academy of Sciences. This microbeam system operates in both full current intensity mode and single ion mode. It delivers a predefined number of ions to preselected targets for research in biology and material science. The characteristic of this microbeam system is high energy and vertical irradiation. A quadrupole focusing system, in combination with a series of slits, has been designed to optimize the spatial resolution. A symmetrically achromatic system leads the beam downwards and serves simultaneously as an energy analyzer. A high gradient quadrupole triplet finally focuses a C6+ ion beam to 1 µm in the vacuum chamber within the energy range from 10 MeV/u to 100 MeV/u. In this paper, the IMP microbeam system is described in detail. A systematic investigation of the ion beam optics of this microbeam system is presented together with the associated aberrations. Comparison is made between the IMP microbeam system and the other existing systems to further discuss the performance of this microbeam. Then the optimized initial beam parameters are given for high resolution and high hitting efficiency. At last, the experiment platform is briefly introduced.

Experimental results of helicon sources

Helicon plasma source is known as an efficient generator of uniform and high density plasma. A helicon plasma source was developed for the investigation of plasma striping and plasma lens at the Institute of Modern Physics, CAS. In this paper, the characteristics of helicon plasma have been studied by using Langmuir four-probe and a high plasma density up to 3.9×1013 /cm3 has been achieved with the Nagoya type III antenna. In the experiment, several important phenomena have been found: (1) for a given magnetic induction intensity, the plasma density became greater with the increase of RF power; (2) the helicon mode appeared at the RF power between 300 W and 400 W; (3) the plasma density gradually tended to saturation as the RF power increased to the higher power; (4) a higher plasma density can be obtained by a good matching between the RF power and the magnetic field distribution. The key issue is how to optimize the matching between the RF power and the magnetic field. Moreover, some tests on the extraction of ion beam were performed, and the preliminary results were given. The problems which existed in the helicon ion source will be discussed and the increase in beam density will be expected by extraction system optimum.

Development of external electron-beam enhancement of the Penning ionization gauge ion source

To study the injection of additional electrons from an external electron gun into the plasma of a Penning ionization gauge (PIG) ion source, a test bench for the external electron-beam enhancement of the PIG (E-PIG) ion source was set up. A source magnet assembly was built to satisfy the request for magnetic field configuration of the E-PIG ion source. Numerical calculations have been done to optimize the magnetic field configuration so as to fit the primary electrons to be fed into the PIG discharge chamber along the spreading magnetic field lines. Many possible methods for improving the performance and stability of the PIG ion source have been used in the E-PIG ion source, including the use of multicrystal LaB6 cathode and optimized axial magnetic field. This article presents a detailed design of the E-PIG ion source. Substantial enhancement of ion charge state is expected to be observed which demonstrates that the E-PIG is a viable alternative to other much more costly and difficult to operate devices for the production of intense ion beams of higher charge state.

Optimization of magnetic field for CR dipole magnet

High homogeneity of the CR (collector ring) dipole magnet for FAIR (Facility for Antiproton and Ion Research) project at GSI is essential. The two optimized and analysis methods are introduced in detail. In order to obtain an ideal integral magnetic field distribution, the complicated end chamfer has been designed. By chamfering the removable pole, the distribution tolerance of high magnetic field is optimized to +/- 2 x 10(-4). The method of adding a mirror plane is suitable for the high magnetic field and it doesn't fit the low one. The OPERA is used to optimize the dipole magnetic field.

Optimization design of magnetic field on cold yoke superconducting solenoid

The optimized design of magnetic field for a cold yoke superconducting solenoid is introduced in this paper. Using some kinds of optimization designs and OPERA, we optimize the main solenoid, cold yoke and compensated winding. Through this design, the requests of the superconducting solenoid are realized.

Geographical constraints to range-based attacks on links in complex networks

In this paper, we studied range-based attacks on links in geographically constrained scale-free networks and found that there is a continuous switching of roles of short-and long-range attacks on links when tuning the geographical constraint strength. Our results demonstrate that the geography has a significant impact on the network efficiency and security; thus one can adjust the geographical structure to optimize the robustness and the efficiency of the networks. We introduce a measurement of the impact of links on the efficiency of the network, and an effective attacking strategy is suggested

Simulation of micromegas detector by garfield program

In this paper, a batch file which describes the detailed structure and the corresponding physical process of Micro-Mesh Gaseous Structure (Micromegas) detector, the macro commands and the control structures based on the Garfield program has been developed. And using the Garfield program controlled by this batch file, the detector's gain and spatial resolution have been investigated under different conditions. These results obtained by the simulation program not only exhibit the influences of the mesh and drift voltage, the mixture gas proportion, the distance between the mesh cathode and the printed circuit board readout anode, and the Lines Per Inch of the mesh cathode on the gain and spatial resolution of the detector, but also are very important to optimize the design, shorten the experimental period, and save cost during the detector development. Additionally, they also indicate that the Garfield program is a powerful tool for the Micromegas detector design and optimization.