Indagine modellistica sulla tenuta idraulica delle difese arginali deputate alla protezione idraulica del territorio

La prima parte di questo lavoro di tesi tratta dell’interazione tra un bacino di laminazione e il sottostante acquifero: è in fase di progetto, infatti, la costruzione di una cassa di espansione sul torrente Baganza, a monte della città di Parma. L’obiettivo di tale intervento è di ridurre il rischio di esondazione immagazzinando temporaneamente, in un serbatoio artificiale, la parte più pericolosa del volume di piena che verrebbe rilasciata successivamente con portate che possono essere agevolmente contenute nel tratto cittadino del torrente. L’acquifero è stato preliminarmente indagato e monitorato permettendone la caratterizzazione litostratigrafica. La stratigrafia si può riassumere in una sequenza di strati ghiaioso-sabbiosi con successione di lenti d’argilla più o meno spesse e continue, distinguendo due acquiferi differenti (uno freatico ed uno confinato). Nel presente studio si fa riferimento al solo acquifero superficiale che è stato modellato numericamente, alle differenze finite, per mezzo del software MODFLOW_2005. L'obiettivo del presente lavoro è di rappresentare il sistema acquifero nelle condizioni attuali (in assenza di alcuna opera) e di progetto. La calibrazione è stata condotta in condizioni stazionarie utilizzando i livelli piezometrici raccolti nei punti d’osservazione durante la primavera del 2013. I valori di conducibilità idraulica sono stati stimati per mezzo di un approccio geostatistico Bayesiano. Il codice utilizzato per la stima è il bgaPEST, un software gratuito per la soluzione di problemi inversi fortemente parametrizzati, sviluppato sulla base dei protocolli del software PEST. La metodologia inversa stima il campo di conducibilità idraulica combinando osservazioni sullo stato del sistema (livelli piezometrici nel caso in esame) e informazioni a-priori sulla struttura dei parametri incogniti. La procedura inversa richiede il calcolo della sensitività di ciascuna osservazione a ciascuno dei parametri stimati; questa è stata valutata in maniera efficiente facendo ricorso ad una formulazione agli stati aggiunti del codice in avanti MODFLOW_2005_Adjoint. I risultati della metodologia sono coerenti con la natura alluvionale dell'acquifero indagato e con le informazioni raccolte nei punti di osservazione. Il modello calibrato può quindi essere utilizzato come supporto alla progettazione e gestione dell’opera di laminazione. La seconda parte di questa tesi tratta l'analisi delle sollecitazioni indotte dai percorsi di flusso preferenziali causati da fenomeni di piping all’interno dei rilevati arginali. Tali percorsi preferenziali possono essere dovuti alla presenza di gallerie scavate da animali selvatici. Questo studio è stato ispirato dal crollo del rilevato arginale del Fiume Secchia (Modena), che si è verificato in gennaio 2014 a seguito di un evento alluvionale, durante il quale il livello dell'acqua non ha mai raggiunto la sommità arginale. La commissione scientifica, la cui relazione finale fornisce i dati utilizzati per questo studio, ha attribuito, con molta probabilità, il crollo del rilevato alla presenza di tane di animali. Con lo scopo di analizzare il comportamento del rilevato in condizioni integre e in condizioni modificate dall'esistenza di un tunnel che attraversa il manufatto arginale, è stato realizzato un modello numerico 3D dell’argine mediante i noti software Femwater e Feflow. I modelli descrivono le infiltrazioni all'interno del rilevato considerando il terreno in entrambe le porzioni sature ed insature, adottando la tecnica agli elementi finiti. La tana è stata rappresentata da elementi con elevata permeabilità e porosità, i cui valori sono stati modificati al fine di valutare le diverse influenze sui flussi e sui contenuti idrici. Per valutare se le situazioni analizzate presentino o meno il verificarsi del fenomeno di erosione, sono stati calcolati i valori del fattore di sicurezza. Questo è stato valutato in differenti modi, tra cui quello recentemente proposto da Richards e Reddy (2014), che si riferisce al criterio di energia cinetica critica. In ultima analisi è stato utilizzato il modello di Bonelli (2007) per calcolare il tempo di erosione ed il tempo rimanente al collasso del rilevato.

Computer analysis of large civil engineering structures

The finite element method is now well established among engineers as being an extremely useful tool in the analysis of problems with complicated boundary conditions. One aim of this thesis has been to produce a set of computer algorithms capable of efficiently analysing complex three dimensional structures. This set of algorithms has been designed to permit much versatility. Provisions such as the use of only those parts of the system which are relevant to a given analysis and the facility to extend the system by the addition of new elements are incorporate. Five element types have been programmed, these are, prismatic members, rectangular plates, triangular plates and curved plates. The 'in and out of plane' stiffness matrices for a curved plate element are derived using the finite element technique. The performance of this type of element is compared with two other theoretical solutions as well as with a set of independent experimental observations. Additional experimental work was then carried out by the author to further evaluate the acceptability of this element. Finally the analysis of two large civil engineering structures, the shell of an electrical precipitator and a concrete bridge, are presented to investigate the performance of the algorithms. Comparisons are made between the computer time, core store requirements and the accuracy of the analysis, for the proposed system and those of another program.

Modeling technique for honeycomb FRP deck bridges via finite elements

Honeycomb structures have been used in different engineering fields. In civil engineering, honeycomb fiber-reinforced polymer (FRP) structures have been used as bridge decks to rehabilitate highway bridges in the United States. In this work, a simplified finite-element modeling technique for honeycomb FRP bridge decks is presented. The motivation is the combination of the complex geometry of honeycomb FRP decks and computational limits, which may prevent modeling of these decks in detail. The results from static and modal analyses indicate that the proposed modeling technique provides a viable tool for modeling the complex geometry of honeycomb FRP bridge decks. The modeling of other bridge components (e.g., steel girders, steel guardrails, deck-to-girder connections, and pier supports) is also presented in this work.

A general technique to embed non-uniform discontinuities into standard solid finite elements

A general technique to embed non-uniform displacement discontinuities into standard solid finite elements is presented. The technique is based on the decomposition of the kinematic fields into a component related to the deformation of the solid portion of the element and one related to the rigid-body motion due to a displacement discontinuity. This decomposition simplifies the incorporation of discontinuity interfaces and provides a suitable framework to account for non-uniform discontinuity modes. The present publication addresses two families of finite element formulations: displacement-based and stress hybrid finite element. © 2005 Elsevier Ltd. All rights reserved.

A wavelet-based adaptive technique for adsorption problems involving steep gradients

A general, fast wavelet-based adaptive collocation method is formulated for heat and mass transfer problems involving a steep moving profile of the dependent variable. The technique of grid adaptation is based on sparse point representation (SPR). The method is applied and tested for the case of a gas–solid non-catalytic reaction in a porous solid at high Thiele modulus. Accurate and convergent steep profiles are obtained for Thiele modulus as large as 100 for the case of slab and found to match the analytical solution.

A model updating technique based on FRFs for damped structures

Model updating methods often neglect that in fact all physical structures are damped. Such simplification relies on the structural modelling approach, although it compromises the accuracy of the predictions of the structural dynamic behaviour. In the present work, the authors address the problem of finite element (FE) model updating based on measured frequency response functions (FRFs), considering damping. The proposed procedure is based upon the complex experimental data, which contains information related to the damped FE model parameters and presents the advantage of requiring no prior knowledge about the damping matrix structure or its content, only demanding the definition of the damping type. Numerical simulations are performed in order to establish the applicability of the proposed damped FE model updating technique and its results are discussed in terms of the correlation between the simulated experimental complex FRFs and the ones obtained from the updated FE model.

The use of the boundary element method in the analysis of single lap joints

The most common techniques for stress analysis/strength prediction of adhesive joints involve analytical or numerical methods such as the Finite Element Method (FEM). However, the Boundary Element Method (BEM) is an alternative numerical technique that has been successfully applied for the solution of a wide variety of engineering problems. This work evaluates the applicability of the boundary elem ent code BEASY as a design tool to analyze adhesive joints. The linearity of peak shear and peel stresses with the applied displacement is studied and compared between BEASY and the analytical model of Frostig et al., considering a bonded single-lap joint under tensile loading. The BEM results are also compared with FEM in terms of stress distributions. To evaluate the mesh convergence of BEASY, the influence of the mesh refinement on peak shear and peel stress distributions is assessed. Joint stress predictions are carried out numerically in BEASY and ABAQUS®, and analytically by the models of Volkersen, Goland, and Reissner and Frostig et al. The failure loads for each model are compared with experimental results. The preparation, processing, and mesh creation times are compared for all models. BEASY results presented a good agreement with the conventional methods.

A FEM-based model to study the behaviour of corroded RC beams shear repaired by NSM CFRP rods technique

This paper presents the main features of finite element FE numerical model developed using the computer code FEMIX to predict the near-surface mounted NSM carbon-fiber-reinforced polymer CFRP rods shear repair contribution to corroded reinforced concrete RC beams. In the RC beams shear repaired with NSM technique, the Carbon Fibre Reinforced Polymer (CFRP) rods are placed inside pre-cut grooves onto the concrete cover of the RC beam’s lateral faces and are bonded to the concrete with high epoxy adhesive. Experimental and 3D numerical modelling results are presented in this paper in terms of load-deflection curves, and failure modes for 4 short corroded beams: two corroded beams (A1CL3-B and A1CL3-SB) and two control beams (A1T-B and A1T-SB), the beams noted with B were let repaired in bending only with NSM CFRP rods while the ones noted with SB were repaired in both bending and shear with NSM technique. The corrosion of the tensile steel bars and its effect on the shear capacity of the RC beams was discussed. Results showed that the FE model was able to capture the main aspects of the experimental load-deflection curves of the RC beams, moreover it has presented the experimental failure modes and FE numerical modelling crack patterns and both gave similar results for non-shear repaired beams which failed in diagonal tension mode of failure and for shear-repaired beams which failed due to large flexural crack at the middle of the beams along with the concrete crushing, three dimensional crack patterns were produced for shear-repaired beams in order to investigate the splitting cracks occurred at the middle of the beams and near the support.

A FEM-based model to study the behaviour of corroded RC beams shear repaired by NSM CFRP rods technique

This paper presents the main features of finite element FE numerical model developed using the computer code FEMIX to predict the near-surface mounted NSM carbon-fiber-reinforced polymer CFRP rods shear repair contribution to corroded reinforced concrete RC beams. In the RC beams shear repaired with NSM technique, the Carbon Fibre Reinforced Polymer (CFRP) rods are placed inside pre-cut grooves onto the concrete cover of the RC beam’s lateral faces and are bonded to the concrete with high epoxy adhesive. Experimental and 3D numerical modelling results are presented in this paper in terms of load-deflection curves, failure modes and slip information of the tensile steel bars for 4 short corroded beams: two corroded beams (A1CL3-B and A1CL3-SB) and two control beams (A1T-B and A1T-SB), the beams noted with B were let repaired in bending only with NSM CFRP rods while the ones noted with SB were repaired in both bending and shear with NSM technique. The corrosion of the tensile steel bars and its effect on the shear capacity of the RC beams was discussed. Results showed that the FE model was able to capture the main aspects of the experimental load-deflection curves of the RC beams, moreover it has presented the experimental failure modes and FE numerical modelling crack patterns and both gave similar results for non-shear repaired beams which failed in diagonal tension mode of failure and for shear-repaired beams which failed due to large flexural crack at the middle of the beams along with the concrete crushing, three dimensional crack patterns were produced for shear-repaired beams in order to investigate the splitting cracks occurred at the middle of the beams and near the support.

Innovative methodologies for the enhancement of the flexural strengthening performance of NSM CFRP technique for RC beams

Tese de Doutoramento em Engenharia Civil

Analysis of a finite volume element method for the Stokes problem

In this paper we propose a stabilized conforming finite volume element method for the Stokes equations. On stating the convergence of the method, optimal a priori error estimates in different norms are obtained by establishing the adequate connection between the finite volume and stabilized finite element formulations. A superconvergence result is also derived by using a postprocessing projection method. In particular, the stabilization of the continuous lowest equal order pair finite volume element discretization is achieved by enriching the velocity space with local functions that do not necessarily vanish on the element boundaries. Finally, some numerical experiments that confirm the predicted behavior of the method are provided.

Mastication effort study using photorefractive holographic interferometry technique

The purpose of this work was the force-displacement response analysis of the masticatory process in a dried human skull by Double-Exposure Photorefractive Holographic Interferometry Technique (2E-PRHI). The load concentration and dissipation of the forces from dried human skull were analysed at applied loading stands as a Simulation of Isolated Contraction (SIC) of some mastication muscles. The 2EHI and Fringe Analysis Method were used to obtain the quantitative results of this force-displacement response. These results document quantitatively the real biomechanical response from dried human skull under applied loading and it can be used for complementary study by finite element model and others analysis type. Crown Copyright (C) 2009 Published by Elsevier Ltd. All rights reserved.

The strut-and-tie models in reinforced concrete structures analysed by a numerical technique

Os modelos de bielas e tirantes são procedimentos de análise apropriados para projetar elementos de concreto armado em casos de regiões onde há alterações geométricas ou concentrações de tensões, denominadas regiões D. Trata-se de bons modelos de representação da estrutura para avaliar melhor o seu comportamento estrutural e seu mecanismo resistente. O presente artigo aplica a técnica da otimização topológica para identificar o fluxo de tensões nas estruturas, definindo a configuração dos membros de bielas e tirantes, e quantifica seus valores para dimensionamento. Utilizam-se o método ESO, e uma variante desse, o SESO (Smoothing ESO) com o método dos elementos finitos em elasticidade plana. A filosofia do SESO baseia-se na observação de que se o elemento não for necessário à estrutura, sua contribuição de rigidez vai diminuindo progressivamente. Isto é, sua remoção é atenuada nos valores da matriz constitutiva, como se este estivesse em processo de danificação. Para validar a presente formulação, apresentam-se alguns exemplos numéricos onde se comparam suas respostas com as advindas de trabalhos científicos pioneiros sobre o assunto.

Application of a model updating technique for health condition monitoring and damage detection of flexible structures

This paper discusses the application of a damage detection methodology to monitor the location and extent of partial structural damage. The methodology combines, in an iterative way, the model updating technique based on frequency response functions (FRF) with monitoring data aiming at identifying the damage area of the structure. After the updating procedure reaches a good correlation between the models, it compares the parameters of the damage structure with those of the undamaged one to find the deteriorated area. The influence of the FEM mesh size on the evaluation of the extent of the damage has also been discussed. The methodology is applied using real experimental data from a spatial frame structure.

Modeling 3-D desiccation soil crack networks using a mesh fragmentation technique

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)