The influence of task design on upper limb muscles fatigue during low-load repetitive work: A systematic review

Ergonomic interventions such as increased scheduled breaks or job rotation have been proposed to reduce upper limb muscle fatigue in repetitive low-load work. This review was performed to summarize and analyze the studies investigating the effect of job rotation and work-rest schemes, as well as, work pace, cycle time and duty cycle, on upper limb muscle fatigue. The effects of these work organization factors on subjective fatigue or discomfort were also analyzed. This review was based on relevant articles published in PubMed, Scopus and Web of Science. The studies included in this review were performed in humans and assessed muscle fatigue in upper limbs. 14 articles were included in the systematic review. Few studies were performed in a real work environment and the most common methods used to assess muscle fatigue were surface electromyography (EMG). No consistent results were found related to the effects of job rotation on muscle activity and subjective measurements of fatigue. Rest breaks had some positive effects, particularly in perceived discomfort. The increase in work pace reveals a higher muscular load in specific muscles. The duration of experiments and characteristics of participants appear to be the factors that most have influenced the results. Future research should be focused on the improvement of the experimental protocols and instrumentation, in order to the outcomes represent adequately the actual working conditions. Relevance to industry: Introducing more physical workload variation in low-load repetitive work is considered an effective ergonomic intervention against muscle fatigue and musculoskeletal disorders in industry. Results will be useful to identify the need of future research, which will eventually lead to the adoption of best industrial work practices according to the workers capabilities.

The influence of pauses on the fatigue of upper limb muscles during the task of ironing

The aim of this study was to analyze the influence of position and pauses on muscle activity and fatigue during the task of ironing. Ten female participants performed the task of ironing in two different positions (standing and sitting) for 10 min each with a 1-min pause at the end of each task. Muscle activity and fatigue from the upper trapezium, anterior deltoid, and pectoralis major were analyzed using surface electromyography. The results showed that the positions had no significant influence on muscle activity; nevertheless, they had significant influence on muscular fatigue. In addition, the pauses were possibly beneficial in decreasing the muscle fatigue, but the results were not conclusive.

Fatigue life assessment of exhaust systems for naval gas turbines

Dissertação para obtenção do Grau de Mestre em Engenharia Mecânica

Determinação da tenacidade à fratura de adesivos estruturais em modo misto pelo ensaio Single-Leg Bending

A utilização de juntas adesivas em aplicações industriais tem vindo a aumentar, em detrimento dos métodos tradicionais tais como a soldadura, brasagem e ligações aparafusadas e rebitadas. Este facto deve-se às vantagens que estas oferecem, como o facto de serem mais leves, comportarem-se bem sob cargas cíclicas ou de fadiga, a ligação de materiais diferentes e menores concentrações de tensões. Para aumentar a confiança no projeto de estruturas adesivas, é importante conseguir prever com precisão a sua resistência mecânica e respetivas propriedades de fratura (taxa crítica de libertação de energia de deformação à tração, GIC, e corte, GIIC). Estas propriedades estão diretamente relacionadas com a Mecânica da Fratura e são estimadas através de uma análise energética. Para este efeito, distinguem-se três tipos de modelos: modelos que necessitam da medição do comprimento de fenda durante a propagação do dano, modelos que utilizam um comprimento de fenda equivalente e métodos baseados no integral J. Como na maioria dos casos as solicitações ocorrem em modo misto (combinação de tração com corte), é de grande importância a perceção da fratura nesta condições, nomeadamente das taxas de libertação de energia relativamente a diferentes critérios ou envelopes de fratura. Esta comparação permite, por exemplo, averiguar qual o melhor critério energético de rotura a utilizar em modelos numéricos baseados em Modelos de Dano Coesivo. Neste trabalho é realizado um estudo experimental utilizando o ensaio Single-Leg Bending (SLB) em provetes colados com três tipos de adesivos, de forma a estudar e comparar as suas propriedades de fratura. Para tal, são aplicados alguns modelos de redução da taxa de libertação de energia de deformação à tração, GI, e corte, GII, enquadrados nos modelos que necessitam da medição do comprimento de fenda e nos modelos que utilizam um comprimento de fenda equivalente. Numa fase posterior, procedeu-se à análise e comparação dos resultados adquiridos durante a fase experimental de GI e GII de cada adesivo. A discussão de resultados foi também feita através da análise dos valores obtidos em diversos envelopes de fratura, no sentido de averiguar qual o critério de rotura mais adequado a considerar para cada adesivo. Foi obtida uma concordância bastante boa entre métodos de determinação de GI e GII, com exceção do adesivo mais dúctil, para o qual o método baseado no comprimento de fenda equivalente apresentou resultados ligeiramente superiores.

Establishing the main Guidelines for Cast Steel to Produce Truck Parts

Este trabalho foi realizado na Scania CV AB e teve como principal objectivo estabelecer uma diretriz sobre a possível utilização de aços vazados. Existe uma grande necessidade na realização deste trabalho, de forma a apoiar os engenheiros de projecto no seu processo de selecção dos materiais mais adequados, para produzir componentes mais leves e de elevado desempenho. Esta diretriz apresenta informação relacionada com propriedades mecânicas, processos de fundição, vazabilidade, tipologia de defeitos, tratamentos térmicos, soldabilidade e tratamentos superficiais dos aços vazados. Este trabalho foi limitado, na seleção de materiais para componentes do camião, a aços vazados que poderiam ser aplicados em dois componentes específicos: um componente estrutural da carroçaria sujeito a esforços de fadiga e a um colector de gases de combustão, sujeito a fluência, oxidação, fadiga por corrosão, fadiga-térmica e fadiga-mecânica. Foi realizado um benchmark focado nestes dois componentes de forma a saber que materiais são utilizados de momento por outras empresas concorrentes. Foi realizada ainda uma análise sobre possíveis materiais que possam ser aplicados em cada componente referido. Foi conduzida uma caracterização no estado bruto de fundição de um aço inoxidável vazado usado para produzir um protótipo do colector de gases. Esta caracterização consistiu numa análise microestrutural e medição de macro e microdurezas. Além da caracterização inicial, foram aplicados um conjunto de tratamentos térmicos, de forma a estudar a possibilidade de eliminar os carbonetos presentes inicialmente nas fronteiras de grão. As principais conclusões deste trabalho são que o aço vazado apresenta potencial para ser uma escolha válida em diversas aplicações, devido a um leque alargado de propriedades apresentadas tipicamente por este material. Relativamente a aplicações estruturais, o aço vazado é vantajoso comparativamente ao ferro fundido, quando são requeridos, por exemplo, soldabilidade e elevada resistência, combinada com elevada tenacidade à fractura. Para componentes sujeitos a elevadas temperaturas de serviço, o aço inoxidável vazado é vantajoso quando usado a temperaturas superiores a 750°C, apesar do seu elevado custo. O tratamento térmico composto por um recozimento de solubilização seguido de envelhecimento, elimina quase na totalidade os carbonetos presentes nas fronteiras de grão e verifica-se um aumento de dureza através de uma precipitação de carbonetos finamente dispersos na matriz, que poderão também aumentar a resistência à fluência.

Predictivity Strength of the Spatial Variability of Phenanthrene Sorption Across Two Sandy Loam Fields

Sorption is commonly agreed to be the major process underlying the transport and fate of polycyclic aromatic hydrocarbons (PAHs) in soils. However, there is still a scarcity of studies focusing on spatial variability at the field scale in particular. In order to investigate the variation in the field of phenanthrene sorption, bulk topsoil samples were taken in a 15 × 15-m grid from the plough layer in two sandy loam fields with different texture and organic carbon (OC) contents (140 samples in total). Batch experiments were performed using the adsorption method. Values for the partition coefficient K d (L kg−1) and the organic carbon partition coefficient K OC (L kg−1) agreed with the most frequently used models for PAH partitioning, as OC revealed a higher affinity for sorption. More complex models using different OC compartments, such as non-complexed organic carbon (NCOC) and complexed organic carbon (COC) separately, performed better than single K OC models, particularly for a subset including samples with Dexter n < 10 and OC <0.04 kg kg−1. The selected threshold revealed that K OC-based models proved to be applicable for more organic fields, while two-component models proved to be more accurate for the prediction of K d and retardation factor (R) for less organic soils. Moreover, OC did not fully reflect the changes in phenanthrene retardation in the field with lower OC content (Faardrup). Bulk density and available water content influenced the phenanthrene transport mechanism phenomenon.

From Mind to Body: Is Mental Practice Effective on Strength Gains? A Meta-Analysis

Mental practice is an internal reproduction of a motor act (whose intention is to promote learning and improving motor skills). Some studies have shown that other cognitive strategies also increase the strength and muscular resistance in healthy people by the enhancement of the performance during dynamic tasks. Mental training sessions may be primordial to improving muscle strength in different subjects. The aim of this study was to systematically review and meta-analiyze studies that assessed whether mental practice is effective in improving muscular strength. We conducted an electronic-computed search in Pub-Med/Medline and ISI Web of Knowledge, Scielo and manual searchs, searching papers written in English between 1991 and 2014. There were 44 studies in Pub-Med/Medline, 631 in ISI Web of Knowledge, 11 in Scielo and 3 in manual searchs databases. After exclusion of studies for duplicate, unrelated to the topic by title and summary, different samples and methodologies, a meta-analysis of 4 studies was carried out to identify the dose-response relationship. We did not find evidence that mental practice is effective in increasing strength in healthy individuals. There is no evidence that mental practice alone can be effective to induce strength gains or to optimize the training effects.

Adhesive selection for single lap bonded joints: Experimentation and advanced techniques for strength prediction

The integrity of multi-component structures is usually determined by their unions. Adhesive-bonding is often used over traditional methods because of the reduction of stress concentrations, reduced weight penalty, and easy manufacturing. Commercial adhesives range from strong and brittle (e.g., Araldite® AV138) to less strong and ductile (e.g., Araldite® 2015). A new family of polyurethane adhesives combines high strength and ductility (e.g., Sikaforce® 7888). In this work, the performance of the three above-mentioned adhesives was tested in single lap joints with varying values of overlap length (LO). The experimental work carried out is accompanied by a detailed numerical analysis by finite elements, either based on cohesive zone models (CZM) or the extended finite element method (XFEM). This procedure enabled detailing the performance of these predictive techniques applied to bonded joints. Moreover, it was possible to evaluate which family of adhesives is more suited for each joint geometry. CZM revealed to be highly accurate, except for largely ductile adhesives, although this could be circumvented with a different cohesive law. XFEM is not the most suited technique for mixed-mode damage growth, but a rough prediction was achieved.

Strength improvement of adhesively-bonded scarf repairs in aluminium structures with external reinforcements

Adhesively bonded techniques are an attractive option to repair aluminium structures, compared to more traditional methods. Actually, as a result of the improvement in the mechanical characteristics of adhesives, adhesive bonding has progressively replaced the traditional joining methods. There are several bonded repair configurations, as single-strap, double-strap and scarf. Compared with strap repairs, scarf repairs have the advantages of a higher efficiency and the absence of aerodynamic disturbance. The higher efficiency is caused by the elimination of the significant joint eccentricities of strap repairs. Moreover, stress distributions along the bond length are more uniform, due to tapering of the scarf edges. The main disadvantages of this technique are the difficult machining of the surfaces, associated costs and requirement of specialised labour. This work reports on an experimental and numerical study of the tensile behaviour of two-dimensional (2D) scarf repairs of aluminium structures bonded with the ductile epoxy adhesive Araldite® 2015. The numerical analysis, by Finite Elements (FE), was performed in Abaqus® and used cohesive zone models (CZM) for the simulation of damage onset and growth in the adhesive layer, thus enabling the strength prediction of the repairs. A parametric study was performed on the scarf angle (α) and different configurations of external reinforcement (applied on one or two sides of the repair, and also different reinforcement lengths). The obtained results allowed the establishment of design guidelines for repairing, showing that the use of external reinforcements enables increasing α for equal strength recovery, which makes the repair procedure easier. The numerical technique was accurate in predicting the repairs’ strength, enabling its use for design and optimisation purposes.

Muscular strength decrease in Rattus norvegicus experimentally infected by Toxocara canis

The muscular strength of experimental infected Rattus norvegicus with 3rd. stage Toxocara canis larvae was investigated. Fifty Wistar rats, divided in three groups (G1 - 20 rats infected by 300 eggs of T. canis; G2 - 20 rats infected by 2,000 eggs of T. canis and G3 - 10 rats without infection) had been used. Ten and 30 days after infection the muscular strength in the fore-feet of the rats was checked; at the same time, the body weight was determined. No significative differences in the body weight were noted among the infected and control rats in both occasions. Otherwise, an impairment on the muscular strength was observed in rats infected with T. canis 30 days after inoculation.

Estudo e otimização de juntas do tipo Tpeel soldadas, adesivas e híbridas

A necessidade de utilizar métodos de ligação que melhor satisfaçam as necessidades de projeto tem causado a crescente utilização das juntas adesivas, em detrimento dos métodos tradicionais tais como a soldadura, ligações aparafusadas e rebitadas. A sua utilização em diversas aplicações industriais justifica-se pela redução de peso, redução de concentrações de tensões, isolamento acústico e melhor resistência à corrosão. Contudo, também apresentam desvantagens, como a necessidade de preparação das juntas, a fraca resistência a esforços de arrancamento e a complexidade da previsão da sua resistência. As juntas híbridas são obtidas por combinação de uma técnica tradicional com uma ligação adesiva. As juntas híbridas adesivas-soldadas obtêm-se através da combinação da ligação adesiva com a ligação soldada, sendo a soldadura de resistência por pontos a técnica de soldadura mais usada no fabrico deste tipo de juntas. A sinergia entre ligação adesiva e soldadura por pontos oferece vantagens competitivas em relação às ligações adesivas, tais como superior resistência e rigidez, e maior resistência ao arrancamento e à fadiga. No presente trabalho é apresentado um estudo experimental e numérico de juntas T-peel soldadas, adesivas e híbridas (adesivas-soldadas) solicitadas ao arrancamento. Considerouse o adesivo frágil Araldite® AV138 e os adesivos dúcteis Araldite® 2015 e Sikaforce® 7752 e aderentes de aço (C45E). Foi realizada uma análise dos valores experimentais e efetuada uma comparação destes valores com os resultados obtidos pelo Método de Elementos Finitos (MEF) no software ABAQUS®, que incluiu uma análise de tensões na camada de adesivo e previsão do comportamento das juntas por MDC. Observou-se que, dos três adesivos em estudo, o adesivo Sikaforce® 7752 é o que apresenta o melhor desempenho na ligação de juntas T-peel. A boa concordância entre os resultados experimentais e numéricos permitiu validar a utilização de MDC para previsão da resistência de juntas T-peel adesivas e híbridas. Assim, o presente trabalho representa uma base para posterior aplicação no projeto deste tipo de ligação, com as vantagens decorrentes na redução do tempo de projeto e maior facilidade de otimização.

Strength and damage analysis of composite-aluminium adhesively-bonded single-lap joints

With the need to find an alternative way to mechanical and welding joints, and at the same time to overcome some limitations linked to these traditional techniques, adhesive bonds can be used. Adhesive bonding is a permanent joining process that uses an adhesive to bond the components of a structure. Composite materials reinforced with fibres are becoming increasingly popular in many applications as a result of a number of competitive advantages. In the manufacture of composite structures, although the fabrication techniques reduce to the minimum by means of advanced manufacturing techniques, the use of connections is still required due to the typical size limitations and design, technological and logistical aspects. Moreover, it is known that in many high performance structures, unions between composite materials with other light metals such as aluminium are required, for purposes of structural optimization. This work deals with the experimental and numerical study of single lap joints (SLJ), bonded with a brittle (Nagase Chemtex Denatite XNRH6823) and a ductile adhesive (Nagase Chemtex Denatite XNR6852). These are applied to hybrid joints between aluminium (AL6082-T651) and carbon fibre reinforced plastic (CFRP; Texipreg HS 160 RM) adherends in joints with different overlap lengths (LO) under a tensile loading. The Finite Element (FE) Method is used to perform detailed stress and damage analyses allowing to explain the joints’ behaviour and the use of cohesive zone models (CZM) enables predicting the joint strength and creating a simple and rapid design methodology. The use of numerical methods to simulate the behaviour of the joints can lead to savings of time and resources by optimizing the geometry and material parameters of the joints. The joints’ strength and failure modes were highly dependent on the adhesive, and this behaviour was successfully modelled numerically. Using a brittle adhesive resulted in a negligible maximum load (Pm) improvement with LO. The joints bonded with the ductile adhesive showed a nearly linear improvement of Pm with LO.

Developing and validating a measure of the strength of the HRM system: Operationalizing the construct and relationships among its dimensions

The four studies in this article introduce a questionnaire to measure Strength of the HRM System (HRMSQ), a multidimensional construct, theoretically developed by Bowen and Ostroff (2004). Strength of the HRM System is a set of process characteristics that lead to effectiveness in conveying signals to employees that allow them to create a shared meaning of desired and appropriate work behaviours. Nine characteristics are suggested, grouped in three features: Distinctiveness, Consistency and Consensus. Study 1 developed and tested a questionnaire in a sample of workers from five different sectors. Study 2 cross-validated the measure in a sample of civil servants in a municipality. These two studies used performance appraisal as the reference HRM practice and led to a short version of the HRMSQ. Study 3 and Study 4 extend the HRMSQ to several common HRM practices. The HRMSQ is tested in two samples, of call center and several private and public organizations‟ workers (study 3). In study 4 the questionnaire is refined and tested with a sample from a hotel chain and finally cross-validated with two other samples, in the insurance and batteries sectors, leading to a longer version of the HRMSQ. Content analysis of several interviews with human resource managers and the Rasch model (1960, 1961, 1980), were used to define and select the indicators of the questionnaire. Convergent, discriminant and predictive validity of the measure are tested. The results of the four studies highlight the complexity of the relationships between the proposed characteristics and support the validity of a parsimonious measure of Strength of the HRM System.

Impact of the HRM content (i.e. practices) and process (i.e. strength) on individual and organizational outcomes, in the hotel industry

A Work Project, presented as part of the requirements for the Award of a Masters Degree in Management from the NOVA – School of Business and Economics