Automação da drenagem no teste de produção convencional em tanque cilíndrico

This document aims to improve the quality of the production test in vertical tanks with free water drain pipes, through a device to control the draining system. This proposal consists of an interface detector close to the tank bottle and a control valve on the pipe-drain; they are attached to a remote supervisor system, which will be minimizing the human influence in the conclusion of the test result. And for more consciousness the work shows the importance of the wells production test in the attendance and diagnosis of the productive process, informing the large number of tests executed and problems of the procedure adopted in the field today. There are many possible sources of uncertainty in this kind of test as shown in the experiments realized in the field; the object prototype of this dissertation will be made in the field, based upon the definition of parameters and characteristics of the devices proposal. For a better definition of the draining process the action results of the assessment test are shown, especially changed some for the understand ing of the real process. It shows the proposal details and the configuration that will be used in the tank of Monte Alegre s field Production Station, explaining the interface detector kind and the control system. It is the base to a pilot project now in development, named as the new project classified in the status of the new technology and production improvement of PETROBRAS in Rio Grande do Norte and Ceará. This dissertation concludes that the automation of the conventional test with the draining system will bring benefits both economically as metrologically, because it reduces the uncertainty of the test procedures with free water draining, and also decreases the number of tests with problems

Effect of oxygen on the electrical characteristics of field effect transistors formed from electrochemically deposited films of poly(3-methylthiophene)

Field effect devices have been formed in which the active layer is a thin film of poly(3-methylthiophene) grown electrochemically onto preformed source and drain electrodes. Although a field effect is present after electrochemical undoping, stable device characteristics with a high modulation ratio are obtained only after vacuum annealing at an elevated temperature, and only then if the devices are held in vacuo. The polymer is shown to be p type and the devices operate in accumulation only. The hole mobility in devices thermally annealed under vacuum is around 10 -3 cm 2 V -1 s -1. On exposure to ambient laboratory air, the device conductance increases by several orders of magnitude. This increase may be reversed by subjecting the device to a further high-temperature anneal under vacuum. Subsidiary experiments show that these effects are caused by the reversible doping of the polymer by gaseous oxygen.

Electronic transport in field-effect transistors of sexithiophene

The electronic conduction of thin-film field-effect-transistors (FETs) of sexithiophene was studied. In most cases the transfer curves deviate from standard FET theory; they are not linear, but follow a power law instead. These results are compared to conduction models of "variable-range hopping" and "multi-trap-and-release". The accompanying IV curves follow a Poole-Frenkel (exponential) dependence on the drain voltage. The results are explained assuming a huge density of traps. Below 200 K, the activation energy for conduction was found to be ca. 0.17 eV. The activation energies of the mobility follow the Meyer-Neldel rule. A sharp transition is seen in the behavior of the devices at around 200 K. The difference in behavior of a micro-FET and a submicron FET is shown. (C) 2004 American Institute of Physics.

A Hydrogeologic Evaluation of the Waterloo Area in the Upper Jefferson River Valley, Montana

The Upper Jefferson River is one of the most dewatered rivers in Montana. The river exists in an intermontane basin filled with sediment transported from the Highland Mountains to the west, the Tobacco Root Mountains to the east, and the Jefferson River from the south. The Upper Jefferson River Valley is highly dependent on the Jefferson River as the main industry in the valley is agriculture. A majority of the valley is irrigated and used to grow crops, and a good portion is also used for cattle grazing. The residents of the Upper Jefferson River Valley use the aquifer as the main source of potable water. The Jefferson River is also widely used for recreation. This study took place in the Waterloo area of the Upper Jefferson River Valley, approximately 20 miles south of Whitehall, Montana. The Waterloo area provides significant groundwater base flow to the Jefferson River, which is particularly important during the late irrigation season when the river is severely dewatered, and elevated surface-water temperatures occur, creating irrigation water shortages and poor trout habitat. This area contains two springfed streams, Willow Springs and Parson’s Slough, which discharge to the Jefferson River providing cool water in the late season as well as providing the most important trout spawning habitat in the valley. The area is bordered on both the east and west by irrigation ditches, and about 60% of the study area is irrigated. Tile drains were installed in the study area in close proximity to Parsons Slough causing some concern by neighboring residents. This study evaluated relationships between surface water, groundwater, and irrigation practices so that water managers and others can make informed management decisions about the Upper Jefferson River. Data was collected via a network of groundwater wells and surface-water sites. Additionally, water-quality samples were taken and an aquifer test was conducted to determine aquifer properties. The field data were analyzed and a groundwater budget was created in order to evaluate the aquifer. Results of the groundwater budget show that seepage from the irrigation canals and irrigation recharge have the biggest influence on recharge of the aquifer. There is significant groundwater outflow from the aquifer in the spring-fed streams as well as discharge to the Jefferson River. In comparing previous study results to this study’s results, there is no evidence of the water table decreasing due to irrigation practice changes or tile drain installation. However, given the amount of recharge irrigation practices contribute to the aquifer, if significant changes were made, they may affect groundwater elevations. Also lining the irrigation ditches would have a significant impact on the aquifer, as the amount of seepage would be greatly reduced.

Experimentation of mitigation techniques to reduce the effects of permafrost degradation on transportation infrastructures at Beaver Creek experimental road site, Alaska Highway, Yukon

Les méthodes de design et de construction des routes développés dans le sud canadien ont maintenant besoin d’être adaptés aux environnements nordiques du pays afin de prévenir le dégel dramatique du pergélisol lors de la construction d’une nouvelle route. De plus, le réchauffement climatique occasionne présentement d’importants problèmes de stabilité des sols dans le nord canadien. Ces facteurs causent des pertes importantes au niveau des capacités fonctionnelles et structurales de l’Alaska Highway au Yukon sur un segment de plus de 200 km situé entre le village de Destruction Bay et la frontière de l’Alaska. Afin de trouver des solutions rentables à long terme, le ministère du transport du Yukon (en collaboration avec le Federal Highway Administration du gouvernement américain, Transports Canada, l’Université Laval, l’Université de Montréal et l’Alaska University transportation Center) a mis en place 12 sections d’essais de 50 mètres de longueur sur l’autoroute de l’Alaska près de Beaver Creek en 2008. Ces différentes sections d’essais ont été conçues pour évaluer une ou plusieurs méthodes combinées de stabilisation thermique telles que le drain thermique, le remblai à convection d’air, le pare-neige / pare-soleil, le remblai couvert de matières organiques, les drains longitudinaux, le déblaiement de la neige sur les pentes et la surface réfléchissante. Les objectifs spécifiques de la recherche sont 1) d’établir les régimes thermiques et les flux de chaleur dans chacune des sections pour les 3 premières années de fonctionnement ; 2) de documenter les facteurs pouvant favoriser ou nuire à l’efficacité des systèmes de protection et ; 3) de déterminer le rapport coûts/bénéfices à long terme pour chacune des techniques utilisées. Pour ce faire, une nouvelle méthode d’analyse, basée sur la mesure de flux d’extraction de chaleur Hx et d’induction Hi à l’interface entre le remblai et le sol naturel, a été utilisée dans cette étude. Certaines techniques de protection du pergélisol démontrent un bon potentiel durant leurs 3 premières années de fonctionnement. C’est le cas pour le remblai à convection d’air non-couvert, le remblai à convection d’air pleine largeur, les drains longitudinaux, le pare-soleil / pare-neige et la surface réfléchissante. Malheureusement, des problèmes dans l’installation des drains thermiques ont empêché une évaluation complète de leur efficacité.

Controlo e monitorização do efluente de uma indústria vitivinícola

O tema deste trabalho é "Controlo e monitorização do efluente de uma indústria vitivinícola" e teve lugar na Adega Cooperativa de Reguengos de Monsaraz - CARMIM. O controlo e monitorização, bem como a caracterização físico-química do efluente deste tipo de indústrias, especialmente na CARMIM, pretendem representar um instrumento importante no sentido da necessidade de se construir uma estação de pré-tratamento de águas residuais, antes destas fazerem parte do sistema de águas residuais municipais. A monitorização do efluente ocorreu em duas épocas distintas, a Época Baixa e a Época de Campanha. Em cada uma das épocas foram monitorizadas operações distintas, como a lavagem dos filtros de terras de diatomáceas, a higienização do equipamento de filtração tangencial, a higienização das cubas de inox, lavagens de cubas de vinho tinto e lavagens de depósitos de vinho branco. Foi também monitorizado o efluente resultante do edifício de engarrafamento, da Adega Velha e da caixa colectora global. Acompanhou-se em cada operação e caixas colectoras, o pH, temperatura e caudal, sempre que possível. Para cada amostra foi efectuada uma caracterização físico-química, que inclui os seguintes parâmetros: carência química em oxigénio, azoto total, fósforo total, nitratos, sólidos suspensos totais e metais como ferro, cobre e manganês. ABSTRACT: "Winery wastewater control and monitoring" is the main theme of all this work. All this occurred in CARMIM - Cooperativa Agrícola de Reguengos de Monsaraz. The control and monitoring, as well as physical and chemistry features of this type of wastewater, particularly related with CARMIM, intend to represent an important instrument towards the necessity of building a pre-treatment wastewater station, before they are part of the municipal wastewater system. The wastewater monitoring took place in two different seasons, the non-vintage and vintage season. ln both seasons there were checked different operations such as, the washing of earth filtering equipment, red and white wine tanks and finally inox tank caustic washing. At the same time, there was also possible monitoring the final wastewater resulting from the bottling line facility, "Old “Cellar (Adega Velha) and global drain boxes. There was preformed a physical chemistry feature for each sample. These features comprehend several parameters: Chemical oxygen demand, total nitrogen, total phosphorous, nitrates, total suspended solids and metals such as iron, cupper and manganese.

Charge accumulation and transport in degenerately doped semiconducting polymers with mixed ionic and electronic conductivity

This thesis is part of the fields of Material Physics and Organic Electronics and aims to determine the charge carrier density and mobility in the hydrated conducting polymer–polyelectrolyte blend PEDOT:PSS. This kind of material combines electronic semiconductor functionality with selective ionic transport, biocompatibility and electrochemical stability in water. This advantageous material properties combination makes PEDOT:PSS a unique material to build organic electrochemical transistors (OECTs), which have relevant application as amplifying transducers for bioelectronic signals. In order to measure charge carrier density and mobility, an innovative 4-wire, contact independent characterization technique was introduced, the electrolyte-gated van der Pauw (EgVDP) method, which was combined with electrochemical impedance spectroscopy. The technique was applied to macroscopic thin film samples and micro-structured PEDOT:PSS thin film devices fabricated using photolithography. The EgVDP method revealed to be effective for the measurements of holes’ mobility in hydrated PEDOT:PSS thin films, which resulted to be <μ>=(0.67±0.02) cm^2/(V*s). By comparing this result with 2-point-probe measurements, we found that contact resistance effects led to a mobility overestimation in the latter. Ion accumulation at the drain contact creates a gate-dependent potential barrier and is discussed as a probable reason for the overestimation in 2-point-probe measurements. The measured charge transport properties of PEDOT:PSS were analyzed in the framework of an extended drift-diffusion model. The extended model fits well also to the non-linear response in the transport characterization and results suggest a Gaussian DOS for PEDOT:PSS. The PEDOT:PSS-electrolyte interface capacitance resulted to be voltage-independent, confirming the hypothesis of its morphological origin, related to the separation between the electronic (PEDOT) and ionic (PSS) phases in the blend.

Power converters in WBG device technology for automotive applications and characterization setups for GaN power transistors

This PhD dissertation envisages the design of innovative power converters exploiting WBG devices to get state-of-the-art performance in products intended for industrial applications of automotive field. The collaborations with different specialized companies, provided the opportunity to access commercially-available state-of-the-art SiC and GaN technologies and the possibility to realize innovative converter prototypes. Concerning SiC technology, the complete design of a $350kW$ Battery Emulator instrument in collaboration with a company leader in the automotive testing sector, was carried out from scratch exploiting state-of-the-art SiC power-modules, planar magnetics and top-notch MCU technologies. Discrete high-voltage GaN switches were exploited in the Power Supplies design for automotive charger application to target improved performances compared to the market state-of-the-art. Specifically, two high-efficiency prototypes, an AC/DC converter and a DC/DC converter of $7.5kW$, have been realized for this purpose. To further investigate the characteristics of state-of-the-art GaN power devices two measurement set-ups have been designed. In particular, the trapping phenomenon causing the collapse of drain current during ON-state with a consequent degradation of ON-resistance has been analyzed.