Estudo das propriedades termofísicas com variação da expansibilidade de compósito desenvolvido com matriz PUR-NOP e carga funcional de argilomineral

In this study were conducted experimental procedures for determination of variation of the expandability of rigid polyurethane foam (PUR) from a natural oil polyol (NOP), specifically the Castor oil plant, Ricinus communis, pure and additions of the vermiculite in phase dispersed in different percentage within a range from 0% to 20%, mass replacement. From the information acquired, were defined the parameters for production of bodies of test, plates obtained through controlled expansion, with the final volume fixed. Initially, the plates were subjected to thermal performance tests and evaluated the temperature profiles, to later be extracted samples duly prepared in accordance with the conditions required for each test. Was proceeded then the measurement of the coefficient of thermal conductivity, volumetric capacity heat and thermal diffusivity. The findings values were compared with the results obtained in the tests of thermal performance, contributing to validation of the same. Ultimately, it was investigated the influence that changes in physical-chemical structure of the material had exerted on the variation of thermophysical quantities through gas pycnometry, scanning electron microscopy (SEM) combined with energy dispersive X-ray fluorescence spectroscopy (EDXRF), infrared spectroscopy using Fourier transform (FTIR), thermogravimetric analysis (TGA) and differential thermal analysis (DTA). Based on the results obtained was possible to demonstrate that all load percentage analyzed promoted an increase in the potential expansion (PE) of the resin. In production of the plates, the composites with density near at the free expansion presented high contraction during the cure, being the of higher density adopted as definitive standard. In the thermal performance tests, the heating and cooling curves of the different composites had presented symmetry and values very close for lines of the temperature. The results obtained for the thermophysical properties of composites, showed little difference in respect of pure foam. The percentage of open pores and irregularities in the morphology of the composites were proportionate to the increment of vermiculite. In the interaction between the matrix and dispersed phase, there were no chemical transformations in the region of interface and new compounds were not generated. The composites of PUR-NOP and vermiculite presented thermal insulating properties near the foam pure and percentage significantly less plastic in its composition, to the formulation with 10% of load

Análise tribológica das malhas multifuncionais obtidas por multicamadas

The present work consists in the analysis of tribologycal properties of basic and multifunctional knitted fabrics. This knowledge has fundamental importance for the textile industry since it can quantify, in an objective way, the tactil. The fabrics used were characterized by friction and mechanical tests for determining the viscoelastic region, wear resistance and friction coefficient of the fabrics used. The stress-strain curve was obtained by the method Kawabata, KES-FB1. Wear tests performed with the aid of equipment Martindale. The measurement of friction coefficient, two methods were used and analyzed comparatively. The first was a method already established worldwide known as KES-FB4 and the second was an innovative method called FRICTORQ, developed by the University of Minho. These two methods were compared taking into account the relative motion between the tribologycal pairs are different from each method. While the first motion is translational, the second is rotational. It was formal that the knitted had a multifunctional fabrics tribologycal performance which was better than the basic knitted fabrics, as the viscoelastic region, was laager highlighting a multifunctional structure, with greater wear resistance mainly on the back side of the knitted fabrics and lower friction coefficient. Performing a comparative analysis between two methods used to measure the friction coefficient, it was formal that both methods were consistent in terms of results. In operational terms, the FRICTORQ showed ease of operation and increased reproducibility of results

Painéis-sanduíche com núcleo de EPS reciclado: metodologia de execução e determinação de propriedades termofísicas

New materials made from industrial wastes have been studied as an alternative to traditional fabrication processes in building and civil engineering. These materials are produced considering some issues like: cost, efficiency and reduction of nvironmental damage. Specifically in cases of materials destined to dwellings in low latitude regions, like Brazilian Northeast, efficiency is related to mechanical and thermal resistance. Thus, when thermal insulation and energetic efficiency are aimed, it s important to increase thermal resistance without depletion of mechanical properties. This research was conducted on a construction element made of two plates of cement mortar, interspersed with a plate of recycled expanded polystyrene (EPS). This component, widely known as sandwich-panel, is commonly manufactured with commercial EPS whose substitution was proposed in this study. For this purpose it was applied a detailed methodology that defines parameters to a rational batching of the elements that constitute the nucleus. Samples of recycled EPS were made in two different values of apparent specific mass (ρ = 65 kg/m³; ρ = 130 kg/m³) and submitted to the Quick-Line 30TM that is a thermophysical properties analyzer. Based on the results of thermal conductivity, thermal capacity and thermal diffusivity obtained, it was possible to assure that recycled EPS has thermal insulation characteristics that qualify it to replace commercial EPS in building and civil engineering industry

Análise teórico-experimental do coeficiente de perfomance (COP) de um sistema de refrigeração por jato-compressão

The use of waste heat of energy conversion equipment to produce a cooling effect, consists currently in a very interesting way of efficiency improvement of energy systems. The present research has as intention the theoretical and experimental study of a new intermittent refrigeration system ejector cycle characteristics, with use of waste heat. Initially, was doing a bibliographical survey about the vapor ejector refrigeration system technology. In the following stage was doing a simulation of the corresponding thermodynamic cycle, with preliminarily intention to evaluate the performance of the system for different refrigerants fluids. On the basis of the results of the simulation were selected the refrigerant fluid and developed an experimental group of benches of the refrigeration system considered, where pressure and temperature sensory had been inserted in strategical points of the refrigeration archetype and connected to a computerized data acquisition system for measure the refrigerant fluid properties in the thermodynamic cycle. The test results obtained show good agreement with the literature

Métodos de determinação de cálcio e magnésio trocáveis e estimativa do calcário residual em um Latossolo submetido à aplicação de calcário e gesso em superfície

A determinação da fração do calcário remanescente no solo (calcário residual), em área onde foi realizada aplicação de calcário em superfície, sem incorporação, na implantação do sistema plantio direto, pode ser uma ferramenta importante para auxiliar na definição do momento em que se faz necessária a reaplicação de calcário. Nesse sentido, os objetivos deste trabalho foram avaliar: quais os teores de Ca e Mg trocáveis, extraídos por percolação com solução de KCl e resina trocadora de íons; a quantidade do calcário aplicado que ainda não havia reagido no solo, mediante a determinação dos teores de Ca e Mg não-trocáveis; e qual a influência do gesso nos teores de Ca e Mg trocáveis e na dissolução do calcário, 18 meses após a aplicação em superfície. O experimento foi realizado em um Latossolo Vermelho distroférrico, em Botucatu (SP). O delineamento experimental foi de blocos casualizados com parcelas subdivididas e quatro repetições. Nas parcelas, foram aplicadas quatro doses de calcário dolomítico (0, 1.100, 2.700 e 4.300 kg ha-1), com PRNT = 71,2 %, e nas subparcelas, duas doses de gesso agrícola (0 e 2.100 kg ha-1). O calcário e o gesso foram aplicados em superfície, sem incorporação. Houve alta correlação na determinação de Ca e Mg trocável entre os métodos de percolação com solução de KCl e resina trocadora de íons. A extração pelo método da resina trocadora de íons superestimou os teores de Ca e Mg trocáveis em solo com recente aplicação de calcário em superfície. A aplicação de gesso em superfície reduziu a dissolução do calcário na camada superficial (0-0,10 m). Os teores de Ca e Mg não-trocáveis podem ser utilizados para estimar a quantidade de calcário residual no solo.

Avaliação do comportamento tribológico de compósitos poliéster/fibra de vidro utilizando resíduos de poliéster/fibra de vidro e carbonato de cálcio como carga

The use of composite materials and alternative is being increased every day, as it becomes more widespread awareness that the use of renewable and not harmful to the environment is part of a new environmentally friendly model. Since its waste (primarily fiberglass) can not be easily recycled by the difficulty that still exists in this process, since they have two phases mixed, a polymeric matrix thermoset difficult to recycle because it is infusible and phase of fiber reinforcements. Thermoset matrix composites like Polyester + fiberglass pose a threat due to excessive discharge. Aiming to minimize this problem, aimed to reuse the composite Polyester + fiber glass, through the wastes obtained by the grinding of knifes and balls. These residues were incorporated into the new composite Polyester/Fiberglass for hot compression mold and compared tribological to composites with filler CaCO3, generally used as filler, targeting a partial replacement of CaCO3 by such waste. The composites were characterized by thermal analysis (TGA, DSC and DMA), by the surface integrity (roughness determination, contact angle and surface energy), mechanical properties (hardness) and tribological tests (wear and coefficient of dynamic friction) in order to evaluate the effect of loads and characterize these materials for applications that can take, in the tribological point of view since waste Polyester + fiberglass has great potential for replacement of CaCO3

Número mínimo de colheitas em pepino híbrido estimado por meio do coeficiente de repetibilidade

O objetivo deste trabalho foi estimar o número mínimo de colheitas em experimento com a cultura do pepino. Foram analisados dados de um experimento onde avaliaram-se 14 híbridos de pepino japonês, no delineamento em blocos ao acaso, com quatro repetições e cinco plantas por parcela, conduzidas sob ambiente protegido. Foram efetuadas 32 colheitas, três colheitas por semana, por um período de 72 dias e estimados os coeficientes de repetibilidade, com base na análise de componentes principais para os caracteres produção de frutos por planta, em massa e número, total e comercial. Os resultados permitiram concluir que menos de nove colheitas foram suficientes para analisar as diferenças de produtividade entre os diferentes híbridos, com 95% de certeza de serem eleitos os mais produtivos.

Aspectos metodológicos para análise de depósitos de pulverizações pela determinação dos depósitos pontuais

Objetivou-se com este trabalho avaliar a variabilidade dos depósitos de traçadores, simulando herbicidas aplicados em pós-emergência, em populações de Brachiaria plantaginea e Commelina benghalensis infestantes da cultura da soja. Os depósitos dos traçadores foram também avaliados em plantas da cultura, utilizando-se o pulverizador de barra tratorizado, com pontas de jato plano da série 110-SF-03, aplicando o volume de 250 L ha-1 de calda preparada com 0,18% de corante Azul Brilhante e 0,18% de Amarelo Saturn Yellow. Os alvos naturais utilizados foram: plantas de soja com 150 repetições; B. plantaginea no estádio de duas a oito folhas, coletadas na linha da cultura com 141 repetições; e B. plantaginea e C. benghalensis nas entrelinhas, com 150 e 50 repetições, respectivamente. Os alvos artificiais foram constituídos por lâminas distribuídas a 0, 12,2 e 22,5 cm da linha da cultura. Após a aplicação, os alvos foram coletados individualmente e lavados com 30, 20 e 15 mL de água deionizada, para soja, lâminas e plantas daninhas, respectivamente. Estas originaram as amostras analisadas em espectrofotômetro, estimando-se o depósito de calda em µL por planta e µL cm² de área foliar. Foram ajustadas curvas de regressão entre os depósitos unitários e as freqüências acumuladas, utilizando-se o modelo de Gompertz. As relações entre os depósitos máximos e mínimos foram de 7, 4, 10 e 6 para soja, C. benghalensis e B. plantaginea na linha e na entrelinha, respectivamente. As plantas de B. plantaginea da entrelinha receberam, em média, 34% a mais de depósito do que as plantas da linha.

Determinação dos períodos de interferência de plantas daninhas na cultura do girassol

O objetivo deste estudo foi determinar o período anterior à interferência e o período total de prevenção à interferência da comunidade infestante sobre a cultura do girassol (híbrido M 734). O delineamento experimental utilizado foi o de blocos casualizados, com quatro repetições. Os tratamentos foram compostos por parcelas constituídas por períodos de controle e de presença de plantas daninhas. Para os períodos de controle, o girassol foi mantido livre das plantas daninhas pelos períodos crescentes de 7, 14, 21, 28, 35, 42, 49 e 125 dias após a sua emergência (DAE). Quanto a convivência, a cultura foi mantida na presença da comunidade infestante pelos mesmos períodos. Foram avaliados a densidade e o peso da matéria seca das plantas daninhas e, no girassol, a altura de plantas, o diâmetro de capítulos e a produtividade de aquênios e de óleo. Para a produtividade de aquênios, o período anterior à interferência foi de 15 DAE da cultura, e o período total de prevenção à interferência, de 39 DAE. O período crítico de prevenção à interferência abrangeu 24 dias do ciclo da cultura. Quanto à produtividade de óleo, o período anterior à interferência foi de 32 DAE, e o período total de prevenção à interferência, de 28 DAE.

Determinação experimental e modelagem termodinâmica do ponto de turbidez de sistemas aquosos com tensoativos nonilfenolpolietoxilados

The nonionic surfactants are composed of substances whose molecules in solution, does not ionize. The solubility of these surfactants in water due to the presence of functional groups that have strong affinity for water. When these surfactants are heated is the formation of two liquid phases, evidenced by the phenomenon of turbidity. This study was aimed to determine the experimental temperature and turbidity nonilfenolpoliethoxyled subsequently perform a thermodynamic modeling, considering the models of Flory-Huggins and the empirical solid-liquid equilibrium (SLE). The method used for determining the turbidity point was the visual method (Inoue et al., 2008). The experimental methodology consisted of preparing synthetic solutions of 0,25%, 0,5%, 1%, 2%, 3%, 4%, 5%, 6%, 7%, 8%, 9%, 10%, 12,5%, 15%, 17% and 20% by weight of surfactant. The nonionic surfactants used according to their degree of ethoxylation (9.5, 10, 11, 12 and 13). During the experiments the solutions were homogenized and the bath temperature was gradually increased while the turbidity of the solution temperature was checked visually Inoue et al. (2003). These temperature data of turbidity were used to feed the models evaluated and obtain thermodynamic parameters for systems of surfactants nonilfenolpoliethoxyled. Then the models can be used in phase separation processes, facilitating the extraction of organic solvents, therefore serve as quantitative and qualitative parameters. It was observed that the solidliquid equilibrium model (ESL) was best represented the experimental data.

Determinação de dados de equilíbrio líquido-vapor a altas pressões para sistemas de hidrocarbonetos assimétricos

Crude oil is a complex liquid mixture of organic and inorganic compounds that are dominated by hydrocarbons. It is a mixture of alkanes from the simplest to more complex aromatic compounds that are present derivatives such as gasoline, diesel, alcohol, kerosene, naphtha, etc.. These derivatives are extracted from any oil, however, only with a very high quality, in other words, when the content of hydrocarbons of low molecular weight is high means that production of these compounds is feasible. The American Petroleum Institute (API) developed a classification system for the various types of oil. In Brazil, the quality of most of the oil taken from wells is very low, so it is necessary to generate new technology to develop best practices for refining in order to produce petroleum products of higher commercial value. Therefore, it is necessary to study the thermodynamic equilibrium properties of its derivative compounds of interest. This dissertation aims to determine vapor-liquid equilibrium (VLE) data for the systems Phenilcyclohexane - CO2, and Cyclohexane - Phenilcyclohexane - CO2 at high pressure and temperatures between 30 to 70oC. Furthermore, comparisons between measured VLE experimental data from this work and from the literature in relation to the Peng- Robinson molecular thermodynamic model, using a simulation program SPECS IVCSEP v5.60 and two adjustable interaction parameters, have been performed for modeling and simulation purposes. Finally, the developed apparatus for determination of phase equilibrium data at high pressures is presented

Recuperação e purificação de quitosanases usando adsorção em leito expandido com streamline DEAE com modelagem e simulação usando redes neurais

Expanded Bed Adsorption (EBA) is an integrative process that combines concepts of chromatography and fluidization of solids. The many parameters involved and their synergistic effects complicate the optimization of the process. Fortunately, some mathematical tools have been developed in order to guide the investigation of the EBA system. In this work the application of experimental design, phenomenological modeling and artificial neural networks (ANN) in understanding chitosanases adsorption on ion exchange resin Streamline® DEAE have been investigated. The strain Paenibacillus ehimensis NRRL B-23118 was used for chitosanase production. EBA experiments were carried out using a column of 2.6 cm inner diameter with 30.0 cm in height that was coupled to a peristaltic pump. At the bottom of the column there was a distributor of glass beads having a height of 3.0 cm. Assays for residence time distribution (RTD) revelead a high degree of mixing, however, the Richardson-Zaki coefficients showed that the column was on the threshold of stability. Isotherm models fitted the adsorption equilibrium data in the presence of lyotropic salts. The results of experiment design indicated that the ionic strength and superficial velocity are important to the recovery and purity of chitosanases. The molecular mass of the two chitosanases were approximately 23 kDa and 52 kDa as estimated by SDS-PAGE. The phenomenological modeling was aimed to describe the operations in batch and column chromatography. The simulations were performed in Microsoft Visual Studio. The kinetic rate constant model set to kinetic curves efficiently under conditions of initial enzyme activity 0.232, 0.142 e 0.079 UA/mL. The simulated breakthrough curves showed some differences with experimental data, especially regarding the slope. Sensitivity tests of the model on the surface velocity, axial dispersion and initial concentration showed agreement with the literature. The neural network was constructed in MATLAB and Neural Network Toolbox. The cross-validation was used to improve the ability of generalization. The parameters of ANN were improved to obtain the settings 6-6 (enzyme activity) and 9-6 (total protein), as well as tansig transfer function and Levenberg-Marquardt training algorithm. The neural Carlos Eduardo de Araújo Padilha dezembro/2013 9 networks simulations, including all the steps of cycle, showed good agreement with experimental data, with a correlation coefficient of approximately 0.974. The effects of input variables on profiles of the stages of loading, washing and elution were consistent with the literature

Preparo de amostras e métodos para a determinação do teor de óleo essencial de frutos de limoeiro

Objetivou-se avaliar alternativas de preparo da amostra e os métodos quantitativos para a determinação do teor de óleo em frutos de limão. Os tratamentos foram avaliados por meio do delineamento estatístico inteiramente casualizado, em esquema fatorial 2x2x6, com quatro repetições, sendo duas variedades-copa de limoeiro verdadeiro ('Siciliano' e 'Eureka'), dois métodos analíticos para a determinação do teor de óleo (Scott e Clevenger) e seis formas de preparo dos frutos para análise (análise do fruto inteiro; frutos cortados na longitudinal e análise de ¼; frutos cortados na longitudinal e análise de ¹/2; frutos cortados ao meio e análise da parte superior; frutos cortados ao meio e análise da parte inferior; e análise de ²/8 do fruto). O método denominado de Clevenger foi o mais eficiente na determinação do teor de óleo essencial, e as formas de preparo de amostras ½ inferior, ½ superior, ¼ longitudinal e ½ longitudinal dos frutos proporcionaram valores superiores de óleo essencial.

Comparação entre métodos para determinação de carbono orgânico em amostras de solo mensuradas por volume ou massa

O uso da massa (g) ou do volume (cm³) como medida da quantidade de solo para determinação do teor de C orgânico do solo (COS), bem como a utilização de diferentes métodos de determinações analíticas empregados para essa mesma finalidade, pode alterar diretamente a interpretação dos resultados. Este trabalho teve como objetivo comparar os métodos colorimétricos e titulométricos de determinação de matéria orgânica em três solos com diferentes texturas, tomando-se as amostras por massa (pesagem) e por volume (cachimbagem). Houve variação no teor de COS entre os métodos estudados para um mesmo solo. O uso da massa e do volume alterou diretamente a interpretação dos teores de matéria orgânica no solo. Há variações nos métodos de determinação de COS entre solos de diferentes texturas.

Determinação de dados de equilíbrio de fases para sistemas aquosos com eletrólitos

In the present work are established initially the fundamental relationships of thermodynamics that govern the equilibrium between phases, the models used for the description of the behavior non ideal of the liquid and vapor phases in conditions of low pressures. This work seeks the determination of vapor-liquid equilibrium (VLE) data for a series of multicomponents mixtures of saturated aliphatic hydrocarbons, prepared synthetically starting from substances with analytical degree and the development of a new dynamic cell with circulation of the vapor phase. The apparatus and experimental procedures developed are described and applied for the determination of VLE data. VLE isobarics data were obtained through a Fischer s ebulliometer of circulation of both phases, for the systems pentane + dodecane, heptane + dodecane and decane + dodecane. Using the two new dynamic cells especially projected, of easy operation and low cost, with circulation of the vapor phase, data for the systems heptane + decane + dodecane, acetone + water, tween 20 + dodecane, phenol + water and distillation curves of a gasoline without addictive were measured. Compositions of the equilibrium phases were found by densimetry, chromatography, and total organic carbon analyzer. Calibration curves of density versus composition were prepared from synthetic mixtures and the behavior excess volumes were evaluated. The VLE data obtained experimentally for the hydrocarbon and aqueous systems were submitted to the test of thermodynamic consistency, as well as the obtained from the literature data for another binary systems, mainly in the bank DDB (Dortmund Data Bank), where the Gibbs-Duhem equation is used obtaining a satisfactory data base. The results of the thermodynamic consistency tests for the binary and ternary systems were evaluated in terms of deviations for applications such as model development. Later, those groups of data (tested and approved) were used in the KijPoly program for the determination of the binary kij parameters of the cubic equations of state original Peng-Robinson and with the expanded alpha function. These obtained parameters can be applied for simulation of the reservoirs petroleum conditions and of the several distillation processes found in the petrochemistry industry, through simulators. The two designed dynamic cells used equipments of national technology for the determination of VLE data were well succeed, demonstrating efficiency and low cost. Multicomponents systems, mixtures of components of different molecular weights and also diluted solutions may be studied in these developed VLE cells